Search Documents

By R. A. Pallanch

This paper, which describes the milling practice at the Midvale concentrator, is one of a series being prepared by the Bureau of Mines. The Midvale concentrator, a custom lead-zinc selective flotation plant, is in Salt Lake County, Utah, on a flat site several hundred yards east of the Jordan River and about 200 yards south of the Denver & Rio Grande Western Railroad tracks leading to Bingham Canyon. The site is at an elevation of about 50 feet above the river, the highest available location, thus allowing maximum storage of tailings.

Jan 1, 1931

By D. A. Douglass

This report describes the tri-n-butyl phosphate extraction of cerium (IV) from a sulfate leach liquor prepared from a bastnaesite concentrate as well as from pure eerie nitrate solutions. The work was done on a laboratory scale using separatory funnels. Extraction from pure cerium solutions entailed no great difficulties; however, extraction from the bastnaesite solution proved more difficult, mainly because of the inhibiting effect of the sulfate ion. Despite this, procedures were developed for obtaining good single-state cerium extraction (95+ percent) and a high-purity product (99+ percent), although the maximization of both cannot be achieved simultaneously. This necessitates a compromise in any extraction scheme.

Jan 1, 1959

By B R. Castley

Consumable materials used in mines are often transported to the working areas down shallow angle decline shafts, typically at anywhere between 10¦ and 30¦ to the horizontal. The winding equipment is usually a relatively small single-drum winder and the material is transported in one or more cars, running on rails in the decline. The winding rope is attached directly to the cars, which are mechanically coupled together. For small rock hoisting declines, the cars are replaced with hoppers or skips. The winder is normally of basic design, fitted with only the minimum required safety devices and very elementary brake control. Since these winders are not ælicensedÆ and are usually located in remote areas, the standard of maintenance on the installations is often poor, leading to frequent accidents, resulting in runaways, derailments and broken ropes. These problems can be overcome easily with the application of the rope haulage principle. When large volumes of ore have to be transported to surface, belt conveyors are used on shallow angle inclines, or high-capacity friction winders are used in vertical shafts. Conveyors are limited to inclines no steeper than 14¦ and vertical shafts with large friction or drum type winders are extremely capital-intensive. Rope haulage systems can be used on decline shafts where the inclination is too steep for belt conveyors and too shallow for conventional drum winders. Rope haulage systems also offer a variety of safety, technical and cost advantages over other winding and transport systems. This paper describes the adaptation of the rope haulage principle to modern requirements and, combined with 21st century electronic technology, explains how the principle can be used as an efficient, safe and practical solution to some problems associated with the transport of materials, personnel and ore in mines. The authors describe the designs, methods of operation, safety aspects, automated control, loading and unloading facilities of modern rope haulage systems used for transporting personnel, material and ore. This paper considers a variety of systems already designed for different applications, from small material-only installations to multi-purpose and large rock-hoisting systems with payloads as much as 180 t. It also describes in more detail, a material transporting system recently commissioned in South Africa.

Jan 1, 2005

By W. H. Hamilton

The Kokomo (Tenmile) mining district has had an output valued between $20 and $30 million, mostly from production of silver, lead, and zinc, since 1878. For many years before World War II, there was little production, as the complex nature of the ores made them unattractive at existing metal prices. Under the stimulus of the war, the Geological Survey and the Bureau of Mines studied they district, and in October 1944 the Bureau of Mines began an exploration project, which included dia¬mond drilling, bulldozer trenching, and geophysical surveying. Project work was continued until March 1949, except for short recesses during 1945, 1947, and 1948. Forty-five diamond-drill holes, totaling about 13,000 feet, were drilled from underground and surface stations on the various properties in the district. Eleven bulldozer trenches, abut 2,400 linear feet, were excavated in an attempt to uncover the outcrop of the middle Quail limestone. These trenches ranged from 100 to 485 feet in length and reached a maximum depth of 15 feet. A limited geophysical investigation was made during the summer of 1946. The length of the traverses were: Magnetic, 990 feet; resistivity, 6,250 feet; and self-potential, 69,780 feet.

Jan 1, 1955

By J. Winterton

Estimating the residual metal inventory of large heap leaching operations is desirable for many reasons. Several methods have been tried with limited success. Drilling data from the Valley Leach Facility at AngloGold Ashanti's Cripple Creek and Victor Gold Mine has been used to develop a robust inventory estimation technique. The technique is presented along with discussion of the particular inventory components and evaluation methodologies.

Feb 27, 2013

It is indeed a privilege and honour to deliver the keynote address at this 15th APCOM symposium. APCOM has played a significant role in my own career and I am sure in the careers of many of the thousands of other participants over the years since its inception as a short course on "Computers and Computer Applications in the Mineral Industry" at the University of Arizona in 1961. The technical papers and addresses presented at the 14 past symposia provide an imposing record of sustained pro- gress and achievement in the field of computer applications. I will not attempt to analyse this technical side of APCOM but rather endeavour to provide you with a broad popular perspective of the road travelled to date and that lying ahead of us. The name of the series of symposia has changed from time to time, with titles such as Mathematical and Statistical Techniques, Mining and Exploration, and Decision Making being used at various times until in 1972 the name APCOM was coined and the present loga designed by the South African organising committee for the 10th symposium. It can conveniently be accepted as standing for:

Jan 1, 1977

By R. J. Tocher

Uniaxial testing was performed on coal specimens to determine the time-dependent response. The testing was carried out on coal from six mine sites throughout the Western United States and Pennsylvania. Testing configurations were varied to allow analysis of moisture dependency, stress level and specimen orientation. Several theories were presented for the behavior of coal due to moisture diffusion. Experimental results showed the correlation between the theories and the actual material response. Coal deformation was found to be highly dependent on the moisture level of the testing environment. Moisture migration causes drying and shrinkage which lead to progressive degradation of the material. The coal tested experienced a rebound if saturated after a period of drying. This type of time-dependent behavior overshadows the dependence on the applied stress level, which, however, still produces a noticeable creep behavior. Analysis of one series of creep test results was performed. A relationship was developed on the basis of a simplified rheological model to describe the coal response to uniaxial stress. Previous empirical formulations in the form of power laws were compared and their deficiencies pointed out.

Jan 1, 1980

By Millard M. Gilkey

This Bureau of Mines report presents results of a detailed study of water usage in the Wyoming mineral industry along with projections for the future In 1964, the mineral industries of Wyoming used 20 billion gallons of new water, nearly all self-supplied, and reused 72 billion gallons, a total usage of 92 billion gallons. Consumption amounted to 2.8 billion gallons. About one-half of the 20 billion gallons of new water was obtained from [srface] sources and the rest from ground water. Reported costs, covering power and maintenance, for the self-supplied new water at mineral industry operations ranged from less than 1 cent to 20 cents per thousand gallons and aver-aged 8 cents. At one mineral-related operation, water was hauled by truck to supplement a well supply. The cost was $2.00 per thousand gallons delivered. However, the supplemental requirement was only 10 gpm. Cost figures for the recirculation of water, covering power and maintenance, averaged 2 cents. In terms of water usage, the value of product for the entire industry was $25 per thousand gallons of new water intake and about $180 per thousand gallons consumed. The study revealed that Wyoming has a water deficiency but that the shortage is less severe than in the arid Southwest. Projection of the water needs of the Wyoming mineral industries indicates that the demand for new water will increase from the 20 billion gallons used in 1964 to 25 billion gallons in 1980, a 25-percent increase. The projected new-water requirement for the year 2000 is 40 billion gallons, a 100-percent increase compared with the 1964 figure.

Jan 1, 1967

By J Savage, A Crawford, M Doyle, N McNaughton, T G. Blenkinsop

Area selection criteria for gold exploration have historically highlighted the low prospectivity of high-metamorphic grade terranes relative to regions with lower metamorphic grades. The Tropicana gold project, Western Australia, is a rare example of a major greenfields gold discovery in Archean mid-amphibolite to granulite-facies gneissic rocks that have experienced widespread recrystallisation and partial melting.The project, located on the tectonically reworked eastern margin of the Yilgarn Craton, is part of the Tropicana Joint Venture, which is 70 per cent owned by AngloGold Ashanti Australia (manager) and 30 per cent by Independence Group NL. Construction of the mine commenced in the June quarter of 2011 and first gold pour from open pit mining is anticipated in the December quarter of 2013. The approved project will have a ten-year mine life and in the first three years of operation, gold production will be between 470 000 - 490 000 oz/a at a cash cost of A$590 - A$630/oz.Reserves as at 31 December 2011 total 56.4 Mt grading 2.16 g/t for 3.91 Moz of gold. The mineral resource, as of 30 December 2012, has grown to 7.89 Moz of contained gold, including Inferred Resources of 11.9 Mt at 2.83 g/t for 1.08 Moz.Economic gold mineralisation post-dates peak metamorphism and is interpreted as younger in age (ca. 2500 Ma) than other gold deposits in the Yilgarn Craton on the basis of structural and geochronological constraints. Mineralisation is genetically related to an imbricate thrust stack that records a prolonged history of reactivation during the Proterozoic era. Gold mineralisation formed from higher temperature (>350¦C) silica-undersaturated fluids that preferentially migrated though a favourable intensely potassium metasomatised zone. Permeability created during brittle fragmentation was accompanied by replacement of mafic metamorphic minerals, and synchronous partitioning of strain into pervasively biotite-sericite-pyrite-altered stylolites and shear planes that bound more competent lithons.CITATION:Doyle, M, Savage, J, Blenkinsop, T G, Crawford, A and McNaughton, N, 2013. Tropicana - unravelling the complexity of a +6 million ounce gold deposit hosted in granulite facies metamorphic rocks, in Proceedings World Gold 2013 , pp 87-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By S Coward, J Vann, R Wolff, S Jackson, S Moayer, A Bye

Uncertainty about the future and orebody should significantly impact evaluation of mining projects. Scenario planning, widely used in other industries, for example in the petroleum industry, can provide organisations with an opportunity to explore the consequences of uncertainty on their future plans. By developing plausible scenarios, scenario planning assists decision makers by allowing them to make systematic and possibly effective decisions for the future. This paper reviews existing mine project evaluation in the context of a new framework called scenario-based project evaluation (SBPE) (Vann et al , 2012) that addresses many shortcomings of existing approaches. SBPE uses conditional simulations (CS) models as inputs which are evaluated against future alternative project pathways (æalternativesÆ). These alternatives are evaluated using multiple plausible images of the deposit (CS realisations) which capture realistic variability and as an ensemble, map uncertainty of various orebody attributes at fine scale. The alternatives can involve different mining, stockpiling, blending and processing strategies. The ultimate output is a (stochastic) set of cash flows for each alternative from which financial measures, such as NPV, can be derived. Alternatives can then be explored in the presence of against external scenarios such as changes in prices, costs, and taxation. The obvious problem with such data rich results is knowing which scenarios or group of scenarios are optimal.An innovative approach to robust stochastic optimisation (RSO) suited to the SBPE framework is presented here for the first time. This approach to RSO aims to deal with the large number of alternatives generated from SPBE. The goal of applying the RSO approach to SBPE is to identify robust strategic alternatives (project configurations) which have the flexibility to deal with variability and uncertainty of geological and processing inputs such as density, grade and process performance. By applying the proposed RSO method, it is possible to deal with uncertainty and identify the best project configuration in the face of a large number of envisaged scenarios. A case study is provided, in which we have tested the application of the proposed method and compared the result with conventional methods. An important conclusion from this research is that selecting the value of the penalty coefficients in the RSO approach proposed is (as is all optimisation) an exercise of trade-offs; a higher net present value (NPV) is generally associated with a higher risk and a lower risk is associated with a lower NPV. Indeed, this is a strong argument for considering the RSO approach outlined here over more conventional approaches.CITATION:Moayer, S, Vann, J, Coward, S, Jackson, S, Bye, A and Wolff, R, 2012. An innovative approach to robust optimisation for scenario-based mineral project evaluation, in Proceedings Project Evaluation 2012 , pp 141-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Michael D. Balen

During the years 1987 through 1989, the Bureau of Mines Alaska Field Operations Center (Bureau) in cooperation with the Western Field Operations Center and the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted mining, geological, and geochemical investigations in the 5.7 million-acre Valdez Creek Mining District (VCMD). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district studies program. The Bureau's MLA program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies. The information also provides the basis for decisions that would expand the domestic supply of important mineral resources, primarily strategic and critical minerals. Much of the MLA work is done jointly with cooperating State or U.S. geological surveys.

Jan 1, 1992

By Sean Gallagher

The restricted workspace present in low-seam coal mines forces workers to adopt awkward working postures (kneeling and stooping), which place high physical demands on the knee and lower back. Method: This article provides an analysis of injury claims for eight mining companies operating low-seam coal mines during calendar years 1996-2008. All cost data were normalized using data on the cost of medical care (MPI) as provided by the U.S. Bureau of Labor Statistics. Results: Results of the analysis indicate that the knee was the body part that led in terms of claim cost ($4.2 million), followed by injuries to the lower back ($2.7 million). While the average cost per injury for these body parts was $13,100 and $14,400, respectively (close to the average cost of an injury overall), the high frequency of these injuries resulted in their pre¬eminence in terms of cost. Analysis of data from individual mining companies suggest that knee and lower back injuries were a consistent problem across companies, as these injuries were each among the top five most costly part of body for seven out of eight companies studied. Application/Impact: Results of this investigation suggest that efforts to reduce the frequency of knee and low back injuries in low-seam mines have the potential to create substantial cost savings.

Jan 1, 2009

By J. E. Dutrizac

"The end of an era in zinc metallurgy took place on July 31, 1976 when the horizontal retort furnaces of the National Zinc Company in Bartlesville, Oklahoma were permanently shut down (1) . For more than a century, horizontal retorting had been the most common method of producing zinc in the United States; it was a thriving industry in many parts of that country, especially in the natural gas belts of Oklahoma and Texas. With the Bartlesville closure, yet another metallurgical process has become an object of historical interest for North American metallurgists. Although shrouded in controversy, the origins of zinc metallurgy seem to date back at least 2000 years. Pyrometallurgical methods with carbon reductants are capable of producing zinc from oxidic zinc ores, but only above the boiling point of the metal. Although slow cooling results in re-oxidation of the zinc vapour by air or carbon monoxide, quenching yields liquid zinc; some form of rapid cooling, either accidental or intentional, was likely used by ancient metallurgists to liquify the metal. Zinc metal found in Athenian objects of the Roman era was likely of accidental origin. The Romans employed brass extensively for coins and ornaments(2) , and this was intentionally produced by the calamine process whereby oxidic zinc ores were added to molten copper under strongly reducing conditions. Zinc appears to have been known in China and India as early as 1000-1300 A.D., and was probably smelted commercially in those countries from the 14th century. Although the early metallurgical procedures were probably inefficient, they were able to produce zinc metal in significant amounts. The large heaps of zinc residues with clay retorts bear testimony to an early smelting industry of impressive magnitude. It is estimated that the heaps at Zawar, India alone represent the extraction of 100 000 tons of metallic zinc(2) In the 1730s the smelting of oxidic zinc ores was developed in England using a vertical retort method. In 1788 a British patent was granted for making zinc from zinc blends (ZnS) by roasting the ore in a coalfired reverberatory furnace, mixing the calcine with charcoal and smelting the mixture with suitable zinc condensation. The English process was very energy intensive, however, and early in the 19th century the Belgians developed a horizontal retort process for the reductiondistillation of zinc that was more fuel efficient. This technique was gradually developed into what came to be known as the Belgian process, the forerunner of the ""modern"" horizontal retort furnace."

Jan 1, 1999

Domestic production of pyrite cinder reached 15.95 million tons in 2006. The pyrite cinder used in cement industry accounts for about 30% production. The remaining 70%, 11.17 million tons, was thrown away as waste, which brought serious environmental and resource problems. A new technology of composite pellet reduction-roasting and magnetic-separation (CPRM) has been developed to utilize pyrite cinder. Pyrite cinder sample, containing 45.56% Fe, 0.19% Cu and 1.45% S, was pelletized with addition of 5% composite agent in balling disc. Green balls after drying were reduced at 700~800 ? for 20min with 300kg/t pulverized coal injection in rotary kiln. After two stages of ball-grinding and four stages of magnetic separation, high grade magnetite concentrate with 66.23% Fe was produced, meanwhile impurities Cu and S was decreased to 0.048% and 0.053%, respectively. And iron recovery of 73.32%, desulphurization of 96.34% and decoppering degree of 74.73% were achieved. Key technique is that composite agent can accelerate reduction of Fe2O3 and transfer copper and sulphur into water-soluble inorganic salts, which can be removed during wet magnetic concentration. This new technology can be used to fully utilize pyrite cinder and produce high quality magnetite concentrates as feed for steel industry, which will help tackle the pollution problem of pyrite cinder and extend iron-bearing raw material sourcing for Chinese steel industry.

Jan 1, 2014

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By A. Chattopadhyay

Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex, ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.

Sep 1, 2012

By J. W. Thompson

This work is a codification and annotation of the Congressional enactments relating to minerals, mineral lands, and mining. It covers every enactment of Congress from the original ordinance of 1785 to the present time, as well as all sections of the Revised Statutes of the United States relating to these subjects. These laws are grouped according to their general subject matter, and are arranged thereunder in numerical or chronological order. Many of the mining statutes include matter not pertinent to the subject, and only those parts of such acts are quoted as will properly show their relation to minerals and mineral lands and indicate how they should be construed. Some mining acts have been repealed or have become obsolete, and others have become incorporated substantially in sections of the Re- vised Statutes; but these are retained in order to show the changes made, and the constructions placed thereon by the courts are given as aids in construing the new or repealing acts. The annotations consist of legal propositions abstracted from the decisions of the various courts and executive officers of the Govern- ment that have interpreted the sections and statutes so codified. These legal propositions are arranged under the different sections and acts with appropriate headings, titles, and subtitles, in logical order, exhibiting the present status of each particular section or act and its application to the subject of mines and mineral lands. The annotations do not purport to be abstracts of decisions on the sub- stantive law of mines and mining generally, but are limited strictly to the interpretation placed on a given section or act definitely re- ferred to by a court or executive officer by the number of the section of the Revised Statutes or the volume and page of the Statutes at Large in which the Congressional enactment is found. It may be observed that the legal propositions stated are not always pertinent to the particular section or act under which they are classed and of which they purport to give a construction. The arrangement, however, is not an arbitrary one, but is so made for the reason that the courts or officers in the construction of a particular section or act definitely referred to by number or volume and page incorporated in the decision matter not strictly pertinent to the par- ticular section or act so designated. This statement applies especially to the interpretations placed on the sections of the Revised Statutes. The decisions abstracted for the purpose of this work are those of the United States Supreme Court, 234 volumes; the various Federal courts, 214 volumes; the decisions of the Department of the Interior

Jan 1, 1915

By Lewis Carroll

AS he contemplates the numerous good things the hard-working committees have evolved for the 140th Meeting of the Institute, the Editor knows just how the walrus felt when he uttered his memorable, if somewhat lugubrious lines. For there are the Annual Reception and Dinner at the Commodore, 'the Gold Supply Symposium, the luncheons, general and special, and the Annual Institute of Metals Lecture, a Round Table on Iron Ore and a wonderful Informal Dance at the Grand Central Art, Gallery, substantial general sessions, a Smoker-and many other things. -Old, friends and new, reminiscences and confidential chats, horizons pushed back by new information and adjusted perspectives, courage revived and ambitions stimulated-one with a flair for the modernistic might make something-or nothing-of the kaleidoscopic preview 'of the coming Annual Meeting.

Jan 1, 1931

By Bernd Friedrich, Elif Emil‑Kaya, Merve Papakci

In the production of SmCo permanent magnets with excellent temperature stability, corrosion resistance, and oxidation resistance, samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are employed. Cobalt (Co) is a crucial component in tool materials, nickel-based alloys, tablet and smartphone batteries, and electric car batteries. REEs and Co have been listed as critical raw materials by the European Union Commission for many years. Due to the ever-growing demand for Co and REEs in technological applications, the recovery of these elements from secondary sources has garnered significant interest. There are two types of SmCo magnets, one of which contains a high amount of iron, approximately 15.2%. This paper focuses on the recycling of Fe-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Feb 15, 2024

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960