Search Documents

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By L. J. Davies

Refractories usage in furnaces for the extraction of nickel from both sulphides and lateritic ores is reviewed. Recent changes in raw materials and basic brick qualities developed to meet the increasing demands of existing and new processes are outlined. Examples of used brick examinations to establish mechanisms of wear are given. The importance of physical and chemical properties are discussed. The use of simulative laboratory testing to aid in refractories development and selection is described.

Jan 1, 1988

By John C. Cook

A 1-year program of exploratory research, to determine the feasibility of radar exploration in advance of coal mining, has been completed. Advance detection of obstructions including faults, clay veins, abandoned wells, and pyritic concretions would improve the safety and efficiency of mining. Initial calculations based on laboratory tests of the RF electrical properties of bituminous coals indicated feasibility; radar waves at frequencies below 100 MHz should be detectable through tens to hundreds of meters of coal and be well-reflected by clay, pyrite and metal obstructions. Using a proprietary, experimental, VHF short-pulse "mining radar" system, two cycles of field testing and equipment improvement were completed. Measurements were made in three bituminous coal mines, a quarry, and a salt mine. Comparisons were made with ground-penetrating radar equipment developed by others for salt dome exploration and for military tunnel detection. The proprietary mining radar equipment and techniques used were found to be the most effective known for coal exploration, but further improvements are needed; one major problem in all systems is interfering clutter signals arising in the equipment and from mine room reverberations through leakage coupling of the antennas to the air. Nevertheless, several practical goals have been achieved: excellent radar reflections were received and identified through up to 30 feet of coal; reflections from a wet, abandoned drill hole were identified by their polarization property and detected at distances up to 272 feet, and mine-wall reflections were detected at distances up to 735 feet (both through salt); propagation through and reflections from large vertical clay veins in coal were demonstrated; experimental results agree reasonably well with theory. The results and experience gained during the project affirm the feasibility of the method. They also provide a firm basis for the development of a practical radar technology for exploration in advance of mining. No Subject Inventions, as defined in the contract, were made in the course of this work.

Jan 1, 1971

By Karoly (Charles) Kocsis, August Greth, Jon Fox

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contributes a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed.The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than the diesel engines. Battery-powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers and (c) reduced mine operating costs due to lower ventilation requirements"

Jan 8, 2018

By A. E. Boone

"The paper presents critical areas in which improved coordination of effort by industry, government and sup-pliers will be essential to continue the growth record of the Canadian mining industry into the 'seventies'. The analysis includes: exploration, production, mining methods, research and development, markets, management and industrial relations. Performance objectives are suggested where tangible results can be measured. The author suggests the methods by which the 'seventies' can be the greatest decade in the history of Canadian mining. It is indicated that a national mineral policy is essential to the Canadian mineral industry."

Jan 1, 1970

The objective of the paper is to develop a material balance calculation procedure for a production unit involving two plants separated by a pipeline. The case study is taken from the oil sands industry. The raw sands are first mixed with water in a conditioning plant, then transported through a pipeline to an oil extraction plant. The combination of pipeline dimensions and nominal throughput creates a significant variable time lag between the two plants. As usual, mass balance calculations required for the evaluation of plant performance indicators, such as bitumen recovery, are inaccurate due to measurement errors. In addition, in the present case study, the time lag of the pipe creates an additional source of uncertainty, which may lead to misinterpretations and wrong decisions. Raw data are usually reconciled through steady-state mass balancing, to correct for measurement errors. However, because of the significant pipeline dynamic lag, standard steady-state daily mass balance may fail at giving an appropriate picture of the operations. The proposed solution to the data reconciliation problem includes the use of a pipeline plug-flow model in the mass balance calculation. To fulfil the industrial constraint that current data reconciliation must not modify past reconciled values, while still satisfying dynamic constraints, a daily one-step method, i.e. a unitary filter-ing horizon, is recommended. The method is illustrated with simulation data, and the results com-pared to those of standard data reconciliation methods.

Jan 1, 2014

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By Joseph A. Holmes

The investigations carried on at the fuel-testing plant of the United States Geological Survey at St. Louis in 1904-1907 included tests of the steaming and gas-producing qualities of many coals and of the possibilif3 of their improvement by briquetting, together with washing and coking tests and tests of some of the resulting coke in the cupola. These tests were part of a general inquiry into the manner of utilizing most efficiently each of the coals under investigation. The equipment used in the cupola tests of coke, the manner of conducting the tests, and the essential results have been described in publications of the Geological Survey," and only the more important conclusions to be drawn from the tests are mentioned in the following pages. The tests were made to show the fitness of the cokes for foundry purposes, but an incidentlll result was to show foundry men and the coke producers the advisability of studying the conditions of foundry practice. The present bulletin, published by the Bureau of Mines because the analyzing and testing of fuels have been transferred from the Gilological Survey to the Bureau of Mines, briefly reviews the status of the coke industry, some features of practice in the use of coke in the foundry, the probable happenings of a cupola heat, and the reasons for modifying charging practice so that a particular coke can be used to best advantage.

Jan 1, 1910

By E. J. Murphy

"INTRODUCTION This investigation is a continuation of previous work 3/4/5/ on the gaseous products of permissible explosives with and without sheaths. The range of oxygen balance of the explosives has been considerably increased. As has been shown previously, certain approximate relations exist between the volumes of gaseous products and the oxygen balance. Further systematization of the data is not feasible, since the method of theoretioal calculatln of the gaseous product is not yet satisfactorily developed. In a previously described method, 6/ it has been assumed that the explosion occurs at constant volume and that thermodynamic equilibrium is established. Apart from the presumably less important uncertainty of some of the thermodynamic data, it is not known how the confinement of the shots in the Bichel gage or the Crawshaw-Jones gage should be treated, or whether thermodynamic equilibrium is fully attained; nor can the extent to which the equilibrium composition changes during the subsequent period of expansion and cooling be judged with any reliability. Therefore, no calculations have been attempted. However, in anticipation of possible future theoretical interest and as an aid in answering practical problems, the new data are presented in the same minute detail as was done previously."

Mar 1, 1948

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

By Philip B. Grote

The deep ocean mining industry is in a pre-commercialization stage of development. In the context of a proper legal/regulatory regime, deep ocean mining system design, site survey, and operation technologies are capable of rapid evolution. The report recommends that the regulatory framework develop in parallel with the industry and presents a rationale for implementing this approach. The Government has several interests in deep ocean mining technology: (1) as a potential regulator, sound regulations should be based on an understanding of the technology; (2) as a potential monitor, survey technologies are relevant; and (3) as an estimator of strategic minerals supplies, it is important to understand the technology which allows economic access to deep ocean minerals. Thus, the major portion of the report presents an in-depth review of systems design, operations, and survey equipment and techniques.

Jan 1, 1979

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By Charles S. Allbright, Frank G. Schwartz, Marvin L. Whisman

Radioactive tracer techniques were used to gain a better knowledge of the types of compounds that cause gum formation in gasoline during storage . A selected organic compound was labeled with tritium and purified . An unstable gasoline was tagged by adding a small amount of the labeled compound . After storage of the gasoline at 110 ° F for 16 weeks , the gum that had formed was recovered . The amount of the test compound converted to gum was determined by liquid scintillation counting . About 70 compounds , including several classes and types , were studied . The compounds , listed in order of descending reactivity in the test fuel , were sulfur compounds , nitrogen compounds , polycyclic hydrocarbons , olefins , alkylbenzenes , and saturates . In the order of decreasing percentage of each in the gum , the compounds were monoolefins , alkylbenzenes , sulfur compounds , polycyclic hydrocarbons , nitrogen compounds , and diolefins . This type of information should be helpful in developing a method for predicting the storage stability of gasoline .

Jan 1, 1964

By Frederick Laist

This paper is a review of Montana reverberatory smelting practice covering a period of approximately fifty years, during which time the small furnaces that had been in use elsewhere for a century or more, without much change in size or method of operation, were revolutionized and were developed into the huge, continuously operating furnaces of today. A study of Montana practice is particularly instructive, since reverberatory furnace smelting for the production of copper matte received more attention there than in other smelting centers and many of the improvements that finally resulted in establishing the preeminence of this type of furnace over the blast furnace originated in Butte and Anaconda. The material in this paper was gathered from original sources, wherever possible, and all of the illustrations were made from original drawings, some of which have been simplified and worked over so as to be better adapted for reproduction. The aim has been to trace the modifications in design and operation which took place during the period in question—the reasons for the changes and the results achieved through them. For developments during the first twenty years, the technical literature of the period was freely drawn upon, but I am particularly indebted to W. M. Kelly, general foreman at the Anaconda Works, whose recollections and personal experience extend back to the early days. I wish to acknowledge the use made of publications of E. P. Mathewson, William Wraith and L. V. Bender, as well as information obtained here and there from friends and associates. The resume of Great Falls practice was compiled from correspondence, notes and drawings found in the files of the old Boston & Montana Co. and the tabulations showing the performance of furnaces at Butte and Anaconda are adapted from plant records and correspondence in the files of the Anaconda Copper Mining Company. The paper deals with some interesting comparisons that were made between furnaces operated under various conditions in connection with the Carson Case, and results obtained when using natural gas as fuel. This part of the paper may be considered original to the extent that these results have not previously been published.

Jan 1, 1934

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist&apos;s interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1984

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By R. G. O'MEARA, Alexander M. Gow, W. T. SCHRENK

Lime is used extensively in the various industries. The National Lime Association in an excellent and recent bulletin lists 23 important in- dustries in which lime plays a vital role; and it thereby justifies the statement that "Lime is one of the most versatile and widely used reagents in the chemical and industrial world." There is, however, one application of this "universal" reagent which has not been mentioned. It is the use of lime in the flotation of ores. An appreciable percentage of the lime produc- tion is consumed by ore-dressing plants. The uses of lime throughout all the industries are more or less re- lated, but "lime" is a broad term; the varieties of lime are more mumerous than the limestones from which it is made, and its use involves a complicated technique. The interrelated application and growing importance of lime in flotation warrant this additional publication on the various "limes," with emphasis on those uses related to the function of lime in flotation. ཁྐྲ་ Lime in water treatment, cyaniding, and amalgamating will be men- tioned, after which its use in flotation will be taken up. This compendium was prepared by the Mississippi Valley Experiment Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, Rolla, Mo.

Apr 1, 1931

By Gerald Edmunds

CASTINGS of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, some-times nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is devel-oped to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and there-fore the position of the grains is more com-plex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicat-ing that thermal contact was better there than in neighboring areas.

Jan 1, 1940

By John J. Mulligan

The Bureau of Mines investigated reports of mineral deposits within 10 miles of the route of the proposed pipeline from Prudhoe Bay to Valdez. No producing lode deposits or lode prospects of possible national economic significance were found. Measured placer deposits in the route are or slight value except possibly some deeply buried gold placer deposits in the Fairbanks and Livengood Quadrangles. The pipeline corridor crosses five belts of minerals having potential economic value: (1) The north slope of the Brooks Range (oil, gas, oil shale, coal, phosphate); (2) the south slope 01 the Brooks Range (copper, gold); (3) the Livengood area (gold); (4) the Fairbanks area lead-silver, antimony); and (5) the Wrangell Mountains-Denali copper belt (copper-gold). The Jarvis Creek coalfield, an eastern extension of the Nenana coalfield, is on the north side of this belt. Scattered along the corridor across the Chugach Mountain and in the vicinity of Valdez are a wide variety of metallic deposits that make up the eastern margin of the Chugach gold belt but do not seem to constitute a well-defined zone.

Jan 1, 1974