Search Documents

By C. W. Davis

This paper is the second of a series of progress reports on a study of the hydrometallurgy of manganese which is being, conducted in an endeavor to make possible utilization-of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of S02 gas on manganese oxides at elevated temperatures may prove of value.

Jan 1, 1930

By Andrew Stafford, Kate Willa Brown Requist, Eric Lutz, Simon Lotero Lopez, Moe Momayez, Jeffrey Gordon

This formal literature review identifies strengths and shortcomings of current literature related to mine rescue, self-rescue, and self-escape technology. Key concepts and factors that influence the decision making behind mine rescue and self-escape were identified. Historically, underground mining has been one of the most dangerous occupations due to the harsh nature of working environments. During the latter half of the twentieth century, and into the twenty-first century, mining fatalities have declined, yet large-scale mine emergencies persist. The emergence of new technologies, in combination with evidencebased mine emergency research, is resulting in new training methods, monitoring systems, and self-escape approaches being tried in operating mines. This review identifies areas in which substantial research is being conducted, such as the use of virtual reality and game-based training and areas that warrant further development such as the measurement and information gathering capabilities of unmanned ground and aerial vehicles, as well as emergency management and incident command systems. This paper summarizes the current underground mine rescue and self-escape landscape in the USA, including the breadth and depth of mine rescue and self-escape training and practices as evident in the literature.

Nov 2, 2023

By YUSONG MIAO, DI WU, XIANRONG YAN, YIPING ZHANG, JIE LIN, KEBIN LI

Rock fragmentation size distribution is often used as an important index to account for the blasting effect because it directly affects the subsequent loading, transportation, and secondary crushing. Due to the mismatching of explosive and rock wave impedance, high boulder yield often occurs which affects the blasting effect. In this study, methods of measuring rock acoustic impedance, rock strength point loading, and detonation wave velocity have been used to obtain more accurate input parameters. Then, in the watershed image segmentation technique, the Gates-Gaudin-Schuhmann and Rosin-Rammler distribution functions have been used to analyze and quantitatively describe the rock fragmentation size distribution in the existing muck-pile. Finally, taking the rock properties, explosive performance, blasting parameters, and system characteristic variable into consideration, support vector machine (SVM) regression model has been analyzed on the learning and prediction of samples. The results show that SVM has a good prediction accuracy, high precision, and strong generalization ability. The optimized matching coefficient of rock and explosive wave impedance K ranges from 2.50 to 2.58 times. This study has developed a series of simple, accurate methods for rock properties analysis, detonation wave velocity measurement, and muck-pile model image processing, and a basis for predicting and evaluating rock fragmentation size distribution and optimizing the matching coefficient before carrying out a blasting operation.

Jan 22, 2021

By Turgut Yalcin

"Recent years have seen a resurgence of interest in flotation cell design, and one of the areas where attention is being focused is flotation in centrifugal fields which aims at increasing the flotation rates by forced bubble-particle contact.A new cycloflotation device was developed at Laurentian University and tested on the nickel ore of Falconbridge Limited in Sudbury. In comparison with conventional flotation, cycloflotation yielded at least seven times faster flotation rates in terms of the mass of solids floated per unit time per unit flotation volume, while producing concentrate grades similar to those of conventional flotation. These results, which were obtained with a bench-scale ""cyclofloat cell,"" suggest that cycloflotation has the potential of setting a new direction in flotation technology.IntroductionFroth flotation is no doubt the dominant separation technique in the mineral processing industry. Since its inception early in this century, much research effort has been and is still being expended on this process. Until recent years, emphasis seems to have been placed on the chemical aspects of flotation, but there is now an increased awareness for the need to improve flotation machine performance and more and more attention is being directed towards this area. In a 1982 article on ""Flotation Machines"" (Young 1982) it is stated that "" ... by now the design of the machines used would have reached a high level of perfection, ... In fact, this is not the case ... "".The process of flotation in a flotation device may be considered to take place in several distinct stages as follows:"

Jan 1, 1994

By R. R. Sayers

"An important, function of the U.S. Bureau of Mines is to instruct miners in first aid, and as a means of promoting interest in it first-aid contests are held under the auspices of the Bureau, usually in coop; ration with other interested organizations, especially the American Red Cross, the National Safety Council and various operators' and Miners' associations. It was early found that the method of judging first-aid meets is one of the most vital factors in determining the degree of success of the meet.It may be safely stated that there is no method for the judging of first-aid contests that has proved ideal. A method that would give the most uniform judging would necessitate the rating of each team by the same judge or committee of judges and, in order that a judge may rate a team satisfactorily, he should see that team perform several events and average the ratings. Such a procedure is not practicable where there are many terms entered in the contest, as it would prolong the meet indefinitely. To overcome this objection the method has been tried of assigning separate judges to each team but this brings in a new factor the individuality of the various judges, some of whom rate closely, others loosely. The next development was to average the judging by having the judges rate different teams for each event. This would seem to solve the problem out it has been found, after using the method over a wide area for a considerable period of time, that the differences in the judging are too marked to be at all satisfactory. The next development was to appoint a committee of chief judges three to five in number especially trained and experienced, to aid the individual judges in rating the teams. This method has proved satisfactory at small meets but, as committee must review the work of each judge on each event, it has not been deemed feasible for a large meet."

Nov 1, 1920

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By Lee J. Raabe

A specialized loading system for tensile and fatigue testing of wire rope was constructed and installed in the U.S. Bureau of Mine Wire Rope Test Facility in Bruceton, Pennsylvania. The computer-controlled closed-loop servo-hydraulic test system which can apply up to 800,000 pounds of force on the rope while stretching it up to 30 inches will be used in the development and verification of hoist rope retirement criteria for ropes in the 1 to 2 ½ in. diameter range. Characteristics and capabilities of the system are discussed.

Jan 1, 1984

By Yi Luo

The efforts to mitigate longwall subsidence influences on various residential and farming structures by many coal mining companies have been successful in the recent years (Luo, et al, 2003). The successes were largely dependent on the accurate subsidence predictions, correct assessments of potential influences, appropriate design and implementation of the mitigation measures. However, such efforts for protecting large industrial structures are still very rare. In this paper, the successful assessment and mitigation of the subsidence influences associated with a very intensive dynamic longwall subsidence process on a large workshop are presented.

Jan 1, 2005

On the 26th of June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19,000 m3 of saturated hydraulic fill into the mine and caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at Normandy?s zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the adjacent Gossan Hill mine had progressed to a point where a self supporting fill material was required to enable full recovery of high grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16th July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in-situ performance.

May 1, 2007

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By Gregory J. Kurras

In 1995 the Marine Minerals Technology Center (MMTC) of the University of Hawaii conducted a sidescan sonar survey and sampling expedition of the submarine geology and hydrothermal systems surrounding the active volcano White Island. The island is located in the Bay of Plenty, within the geothermally active Taupo Volcanic Zone off-shore of the North Island of New Zealand, and is the site of numerous shallow-water hydrothermal systems. The survey system, an EdgeTech DF1000 sonar, was a dual frequency 100 kHz & 500 kHz sonar capable of imaging the seafloor at better than 1 m resolution and possibly detecting gas bubbles within the water column. Sidescan imagery clearly shows sand channels, debris slumps, submarine landslides, and volcanic ridges all around the island to roughly 800 meters offshore. However, analyses of the both raw and processed acoustic data indicate that the sonar was not able to image any of the shallow-water hydrothermal gas seeps known to exist around the island. Vents were located using a commercial fish finder and knowledge from local tour guides and divers. Eleven gas samples from three different sites were collected by divers for analysis of chemical and isotopic composition. Rock samples were collected from thirteen underwater outcrops for correlation with existing data on subarial island flows sampled by previous investigators. Thin sections and XRF analysis were done for each rock to determine mineral assemblages along with major and trace elements, which were used to tie submarine samples to specific subarial stratigraphic layers.

Jan 1, 2011

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By J. D. Miller

Characterization of feed material with respect to expected concentrate grade and recovery is fundamental to the design of improved separation efficiencies and to achieve sustainable development in the utilization of our mineral resources. An important reference point for this characterization is the liberation-limited grade/recovery curve which represents the perfect separation, the best separation which can be achieved for a given feed material limited only by the extent of liberation. Now, liberation-limited grade/recovery curves can be determined based on 3D mineral liberation analysis of feed material. Thus, actual separation efficiencies can be compared to what might be expected for a perfect separation limited only by the extent of liberation. It is shown that 3D mineral liberation analysis based on X-ray micro CT (XMCT) is preferred to 2D section analysis which overestimates the extent of liberation. By way of example, procedures and experimental results are presented and discussed for feed material in the case of phosphate rock flotation.

Jan 1, 2009

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By I Mason, A Wellington, J Hargreaves

Many people are familiar with the use of marine echo sounders which are used by fishermen to monitor water depth and locate schools of fish. Similar technology has recently been used in some West Australian mines to provide detailed maps of ore contacts and other geological structures. Whilst drillhole intersections provide details of the location of a contact at a point, echo sounding can be used to obtain a continuous profile of the contact. A series of profiles together with drillhole intersection data can be used to build a more accurate geological model than can be inferred from drillhole intersections alone. The benefits of this are more complete ore extraction, less dilution and the ability to make more informed financial decisions. This paper presents a case history which demonstrates the successful application of the technology.

Jan 1, 2000

By S. Mostaghel, V. Hernandez, S. Ge

"The automotive industry is under a constant pressure to reduce the weight of vehicles in order to reduce emissions and improve fuel efficiency. As such, there is an ever-growing demand for high strength and high ductility steel grades to meet the need for lightweight automotive components. Over the past decade, the production and application of 2nd and 3rd generation Advanced High Strength Steels (AHSS) as a lightweight material in automobiles has gained significant popularity due to their exceptional mechanical properties. However, the production cost of these high manganese steel remains high, partially due to the need of large amounts of ferromanganese as alloying material in standard steelmaking processes.The current study introduces a new and cost-effective technology for the production of medium- and high-manganese steels, where self-fluxed micro-pellets of manganese ore will be used as the source of manganese that can be injected into the steel bath. Prior to injection, these pellets are subjected to a pre-reduction process using a mixture of H2 and CO gases, where partial metallization of iron and manganese will occur. Direct injection of the pre-reduced micro-pellets provides less volatilization/emission and higher recovery of manganese, and is capable of producing AHSS with 6–18 wt% Mn.INTRODUCTIONAutomakers are constantly searching for lighter, stronger and cheaper materials in an effort to create safer and more fuel efficient vehicles. The introduction of aluminum alloys and polymer composite materials for automotive applications has been carving into what is traditionally one of the most profitable markets of the iron and steel business. The steel industry responded with Advanced High Strength Steel (AHSS)—a family of manganese containing steels which exhibit exceptional strength and ductility."

Jan 1, 2016

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

By Arne M. Myrvang

Rock stress measurements have been carried out by the Mining Department, the Norw. Institute of Technology (NTH) since 1964. Before that time rock stress measurements were carried out at a few locations by the Swedish professor Hast as early as 1958. From the very beginning the NTH engagement in the rock stress measuring field has been very practically aimed, and we have all the time enjoyed a very good cooperation with the Norwegian mining industry. At a very early stage the industry realized that proper measurements with proper equipment could be a very valuable practical tool. Hence the industry also was willing to grant considerable funds for the education of experts and development of measuring techniques. Since 1964 measurements have been carried out in the great majority of Norwegian mines. During the last years a large number of measurements have also been carried out in connection with hydro-electric power plants, road tunnels etc.

Jan 1, 1981

By K. Huttu, A. van Wageningen

"The Kittilä underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittilä achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two openpits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small openpits will mine any remaining near-surface reserves in the future.The Kittilä Mine is located in the Lapland region of northern Finland, approximately 900 km (560 miles) north of Helsinki and 150 km (93 miles) north of the Arctic Circle. With a mine life estimated through 2034, Kittilä is Agnico’s longest-life mine.The mine’s proven and probable reserves contain 32 Mt (4.7 million oz) at 4.6 g/t (0.13 oz/ st) gold. Ore has been mined from underground since 2010. The original 3 kt/d (3,300 stpd) operation underwent an expansion project to increase the throughput capacity of the mill by 1 kt/d (1,100 stpd), starting by the end of 2014.The region around the Kittilä Mine is underlain by mafic volcanic and sedimentary rocks of the Kittilä Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle’s Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between ironrich and magnesium-rich rocks lies a 100- to 200- m (330- to 660-ft) thick structural zone known as the Suurikuusikko Trend. This trend hosts the Kittilä deposit, where multiple mineralized zones have been traced over a strike length of more than 25 km (15 miles).Most of Agnico Eagle’s work has focused on a 4.5-km (2-mile) segment of the Suurikuusikko Trend that hosts the five main zones of the known gold reserves and resources. From south to north they are: Ketola, Etela, Suuri, Roura and Rimpi.The ore at the Kittilä Mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulfide minerals – arsenopyrite and arsenic-rich pyrite. Only about 4 percent is very fine-grained “free gold” (not locked in sulfide grains) and easier to extract. Most of this free gold is found in the outer, oxidized or eroded sections of the ore."

Jan 1, 2015