Search Documents

By G F. Brent, R D. Hart, C Carr, F Felipe

In underground operations, where copper, gold and other metals are mined, the open stopes can be backfilled to stabilise surrounding workings. This fill may consist of tailings from the processing plant, usually mixed in slurry with a binder such as ordinary Portland cement (OPC). Extensive use is made of tailings in OPC-based paste fill, cemented hydraulic fill or cemented aggregate fill applications. A large underground operation such as the Mount Isa Copper Operations utilises over three million tonnes of backfill per annum. Geopolymers offer an alternative binder system with significant environmental advantages over OPC. Geopolymers are formed by polymerisation of aluminosilicate precursors in an alkali medium. They generally form products with superior strength characteristics as well as increased resistance to degradation, particularly under acidic conditions. Geopolymers have lower carbon dioxide emissions associated with their manufacture than OPC and offer further potential advantages, such as the use of less water and more waste materials. The application of geopolymers to weak material systems such as mine backfill has not been widely studied. The aims of this investigation were to assess a range of Australian mine process wastes for suitability as feedstocks in fill applications and to construct a range of these cemented minefills using a geopolymer binder. The physicochemical characteristics of each of the wastes are discussed as well as how they ultimately contribute to the geopolymer cement through direct replacement of OPC. Results from various tests on the candidate geopolymer fill formulations are presented and the potential of such fill formulations to replace OPC in mine backfilling operations is highlighted. The significant potential contribution to reducing greenhouse gas emissions from the use of geopolymer-based mine backfill across the industry is noted. Conversion of a single mine, such as the Mount Isa Copper Operations, is shown to match the reductions in greenhouse gas emissions due to the current total installed photovoltaic electricity generation capacity of Australia. A similar examination of wastes available to a gold mine could potentially yield new binders for use in established or new fill systems.

Jan 1, 2007

By Daniele Tolazzi

Electric Arc Furnaces keep evolving into highly powerful melting units, shrinking taptotap times by increasing the effectiveness of the energy sources and the material fluxes used in the process. Steelmakers are targeting to increase the efficiency of their injection package in order to reduce the overall conversion costs, seeking for technologies specifically designed to promote the metallurgical reactions in a predictable and reproducible process automatically controlled at the correct timing. Many technological enhancements have focused in the gas management, improving the burner design and the penetration capacity of oxygen injectors, dedicated to decarburization and the other exothermic reactions. Instead, lower evolution efforts have been addressed to engineered solutions for managing the addition of solid materials required in slag forming, although they are playing a key role in EAF process optimization, as well. The paper describes the latest solutions designed to manage efficiently the injection of fuel, oxygen and powdered materials in several EAFs and presents the operational results achieved. Accurate control of reliable additions of coal, lime and magnesia proved crucial for the control of the slag FeO and viscosity, generating stable foamy slag and producing cleaner steel.

Aug 17, 2017

This paper examines the integration of risk management into the design philosophy of a project to produce a æzero baseÆ design, which targets a minimum capital cost without adversely impacting upon the operating costs of the resulting plant. The concept of zero base design is similar to zero base budgeting and the desired outcome is to improve the economy of the design. Design requirements are questioned in an attempt to distinguish preference, prejudice and myth from necessity. Where doubt remains a risk management approach is adopted. The key to risk management is not risk elimination, but risk mitigation. Risks can be managed by designing them out, but often this involves considerable capital cost penalties and it is more attractive to accept the risk and design an operating strategy to deal with it. The paper discusses this with some examples of real world risk mitigation strategies that resulted in substantial capital cost savings. The paper concludes that as much as a quarter of project capital costs can be eliminated by a combination of zero base design and carefully crafted risk mitigation strategies.

Jan 1, 2004

By Dale S. Preece, Lee M. Taylor

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry.

Jan 1, 1990

By H. J. Kelly

[This investigation of the refractory properties of seven Pacific Northwest chrome ores and concentrates has shown that five of the ores and one of the concentrates are suitable for making refractories and that all may be used in combination with high-grade chromite. The specific objectives of the investigation were to determine the inherent physic al and chemical characteristics, to shapes using each of the chrome ores and concentrates, to compare the refractory qualities of the laboratory-prepared with commercial chrome refractories. As far as possible, standard tests were used as criteria.]

Jan 1, 1952

By Joseph B. Cummings

"INTRODUCTION The property was first examined by an engineer 3/ of the Bureau of lanes in December 1942 and was later investigated by the sane engineer in January and February 1943. Prominent outcrops and underground exposures of high-grade iron ore, together with mention of sizable intersections of hematite in logs of four widely scattered churn—drill holes, indicated the possible occurrence of a substantial tonnage of iron ore at this old copper producer.From March to May 1943, detailed topographic and geologic mapping of the property was done by the Federal Bureau of Mines, the Federal Geological Survey, and the Arizona Bureau of Mines.Funds were allotted for exploration of the property by churn and diamond drilling. This work was started in December 1943 and completed in June 1944.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts, developed by each exploratory project as soon as practicable after its conclusion. The Mining Drench, Lowell B. Moon, Chief, conducts preliminary exmination, performs the actual exploratory work, and prepares the final report, The Metallurgical Branch, P. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world's largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine's roof. This report was prepared by the U.S. Bureau of Mines to summarize the opinions of 268 coal miners, 29 rust-line supervisors, and 30 MSHA inspectors concerning why people go under unsupported roof, and how to prevent this behavior. Interviews were conducted at six minesites.

Jan 1, 1991

By Alfonso Guzmán da Silva

El análisis del trabajo señala la importancia y aplicación del proceso Sink & Float en la aceleración de la industria minera metálica, la no-metálica y la del carbón del Perú. Dicho procedimiento que implica la separación de una mezcla de partículas de densidades distintas a través de la diferencia de las mismas, tiene como ejemplo más próximo de su ejecución, a la compañía minera Milpo S. A., así como la primera planta instalada para la pre-concentración de minerales en el Perú, la corporación minera Castrovirreyna, en Huancavelica.

Jun 20, 1954

By A. U. Seybolt

A FEW copper-zinc-base alloys meet die-casting requirements reason- ably well, although improvements are desired. Aluminum bronzes, high-tinbronzes and some copper-nickel-zinc alloys can be die-cast, accordingto Herb,1 but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. TABLE 1. Commercial Die-casting Brasses a Constituent Yellow Brass Low-silicon High-siliconb Brass Brass Nickel Silver Composition, Per Cent Cu 57-59 63-65 80 -81.5 42.0 Zn 40-42 33-35 13.5-16.0 41.0 Sn 0.5-1.5 Si 0.75-1.25 3.75-4.25 Pb 1.0 Ni 16.0 Properties Tensile, lb. per sq. in.. 55,000-60,000 65,000-70,000 85,000-95,000 85,000-95,000 Yield, lb. per sq. in.d.. 30,000-35,000 35,000-40,000 65,000-70,000 65,000-72,000 Elong., per cent in 2 in . 15-20 20-30 8-12 10-20 Brinell hardness 120-130 120-130 160-180 160 Specific gravity 8.47 8.50 8.15 8.45 Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy, 3,4 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. c Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb' as 1650° F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600° F., and of the nickel silver as 1675° F. d Criterion not stated.

Jan 1, 1939

By J. Girard-Dwyer, T. Camm

Direct costs such as medical, legal, administrative, and worker’s compensation costs, property damage, lost earnings, and lost benefits are typically used to compute the economic impacts of occupational injuries. However, there are also a number of less obvious, indirect costs that substantially contribute to the overall loss costs. In fact, for every $1 of direct costs an estimated $3 to $5 of indirect costs are also incurred. This paper presents a systems approach that incorporates engineering, economics, psychology, and sociology in order to evaluate the total value of investments in safety. By studying the interrelated system comprised of the injured worker, their family and coworkers, as well as the organizational structure that was the setting for the incident, a methodology can be developed that will more accurately capture the true costs of mine injuries.

This report describes the results of a program to design, procure, install, and evaluate a multi-channel underground telephone system of modern design in the Sunshine Silver Mine near Wallace, Idaho. Although the evaluation portion of the program was deleted, this report contains a cost benefit analysis for such a system using estimates of operational data for the Sunshine Mine. The results show a centrally switched telephone system of conventional design with ruggedized phone enclosures and special environmentally sealed dial pads to be the most economical.

Jan 1, 1982

By John W. Taber

Discovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits appear to be sharp-walled, low-angle-, tabular ore bodies in granite and are at least 10 feet thick. The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaF2 and 1.44 percent SiO2. Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3.

Jan 1, 1952

By W. W. Graff

This paper describing the mining practices at Mine, No. 4 on the Marquette range, Michigan, is one of a series of articles on mining methods and practices in various mining districts in the United States. Mire No. 4 is located in the Swanzy district, in the southern end of the Marquette range, about 3 miles from Gwinn, Mich. The Swanzy district is an isolated ore-bearing formation, and Mine No. 4 is at the extreme southeastern end.

Jan 1, 1930

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Steve Kral

In a lagging economy where profits are tight, businesses cut costs. No revelation there. The mining industry, though, has always looked for ways to reduce production costs — no matter the state of the economy or commodity prices. The fact is, when planning a new mine or the expansion of an existing one, mining companies gamble that commodity prices will be reasonably high when a project comes onstream. It takes millions of dollars and several years to bring a mine into operation. And a lot can happen economically between the time management gives the go-ahead for a new project and its completion.

Jan 1, 2002

By C. V. Deutsch, J. B. Boisvert, J. L. Deutsch

Data used to build geostatistical models come from a wide variety of sources with potentially differing sample errors and volume supports. Typically all available sample measurements are pooled together for statistical analysis irrespective of the quality of the data. The sample data is used to assess spatial continuity, make local estimates and assess uncertainty. A new methodology is proposed to simplify accounting for samples of differing quality. The result is improved estimates with higher weights assigned to high-quality samples, while low-quality samples receive less influence in resource estimation. A new dimension, d, is introduced and calibrated to account for sample error and/or volume during estimation. The addition of an extra dimension can be easily incorporated in existing kriging or inverse distance workflows. The only additional parameters required are the sample error and volume for each datum. The methodology is demonstrated and the improvement in local accuracy is documented. Extending the dimensionality of the domain to four (three spatial dimensions and the additional d dimension) requires a valid 4D variogram model; therefore, the spherical variogram model is generalized to arbitrary n-dimensions.

Jan 1, 2011

By Ingemar Hermansson, Thomas Bjerendal, Mattias Grävare, Carl-John Grävare

"AbstractHigh strain dynamic pile tests (HSDPT) on driven piles have been carried out on a routine basis in Sweden for more than 30 years. The Swedish Commission on Pile research established, in the early 1980s, safety factors based on the percentage of piles tested. The safety factors could then be reduced, creating economic incentives for the contractor to carry out testing.Energy formulas adopted by our neighbour countries, Norway and Denmark, were not accepted in Sweden as a reliable method since the dynamic testing method was considered to be a more scientific and reliable method. It has become almost the only in-situ method used to verify geotechnical bearing capacity on driven piles.The typical Swedish geology of soft soils overlaying very hard strata makes it possible to verify high design loads, typically 20 kN per cm2 of pile cross sectional area for steel piles and 1,5 kN per cm2 for concrete piles.Conventionally a certain percentage of the piles have been tested in Sweden. The EC7, on the other hand states a number of piles to be tested, regardless of the total number of piles. The Swedish NA (National Annex) states a maximum distance between tested piles, which results in better distribution of the test piles over the foundation.For shaft-bearing piles in soft clays, dynamic pile tests have to be correlated by static load tests.Historical backgroundOn a research basis stress-wave measurements have been carried out for a long time in Sweden. One example is a project in the city of Gothenburg, conducted by Fellenius and Pejrud (1964). Strain gauges were glued on the reinforcement bars in 60 m long, precast concrete piles at 3 m and 25 m above the pile tip respectively. Evaluation was done with different methods such as dynamic formulas,stress-wave measurements and in addition compared with static load tests.In the 1975 Building Code in Sweden, driving criteria for concrete piles based on stress-wave theory were introduced, as summarized in Table 1. The driving criteria are intended for 3 and 4 tonne gravity hammers. For hydraulic rigs, which have free-falling hammers, the drop height indicated should be reduced to 80 % of the values in the table. The criteria were considered to include a safety factor of 3,0. For 330 - 450 kN pile load, pile with a standard a cross sectional area of 235 mm x 235 mm was used. For 600 kN load, the standard cross sectional area was 275 mm x 275 mm."

Jan 1, 2014