Search Documents

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens' fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

By M. J. Lawrence

Independent natural resource Valuers are an essential link between miners and mineral explorers on the one hand and the finance industry on the other. Investors (and regulators) expect the mining and financial industries to be vigilant against the use of inappropriate methodology or use of illogical steps within the chosen valuation method. The Australian Corporations Law generally requires an Independent Expert Report to support mergers and takeovers (as well as for capital raising activities). The introduction of the VALMIN Code (1998) by The Australasian Institute of Mining as Metallurgy, has meant that such Reports, when prepared in compliance with it, are now much more comprehensible and reliable than before. This is because the key requirements of the Code are for transparency and materiality in the Technical Assessment and Valuation Reports prepared in connection with the transaction involved. Transparency is particularly important because it allows the reader to identify and understand the assumptions made to derive a value and to then form a view as to the reasonableness of the result. Even though many elements of resource asset valuation practice are undeniably subjective, there must be some basis of objective rationality to it. Where the reasoning is patently illogical or the inputs are chosen to achieve a particular result, the estimated value must be viewed as virtually worthless. Experience, qualifications, competence and repute are the hallmarks of a professional technical auditor and valuer.

Jan 1, 2000

By G. M. Hughes, R. W. Dunn

"AbstractCurrently installed an analogue instrumentation devices at Sherritt 's Ruttan Concentrator control. and/ or measure mill tonnages, grind, pH, density , some reagent and slurry flows, and cell levels. On-stream analysis is used to assay the main process streams. The history of development of process control is reviewed from startup to the present stage of selection of a process control computer. A pragmatic approach has been taken to process control to ensure compatibility with the needs and resources of Ruttan. Emphasis is made of the need to have the mill performing well from a mechanical and instrumentation point of view and to have opera tor acceptance of the computer through training. Plans for the computer phase to achieve these objectives are outlined.IntroductionTHE COPPER-ZINC OREBODY at Ruttan Lake was discovered by Sherritt exploration personnel in 1969 and by mid-1973 a 10,000-tpd mine and concentrator were in operation. After a typical startup period , the major mechanical problems in the crusher and concentrator have been resolved. Metallurgical performance is now up to standards forecast in the feasibility study.The cost of the original instrumentation installations, including an on- stream analyzer, was about one million dollars or 4% of the cost of the milling complex. Although there was no intention of using a process control computer until the plant was operating smoothly, it was understood that all instrumentation was compatible with .a computer, but this did not prove to be correct. This paper cover s the development of the instrumentation loops to date and the control strategies that will eventually be implemented through a process control computer."

Jan 1, 1977

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture fillings and associated alteration on the mechanical behavior of rocks. Experimental results are presented for 98 specimens from the Climax mine, which were tested since the annual report (May 1973). The conclusions reached are based on both these results and those reported in the annual report. The locations studied are the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from: 1) Climax, medium-grained granite, fine-grained granite, granite porphyry, schist, and gneiss; 2) Henderson, rhyolite porphyry; 3) San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineralogy, composition and fabric of fracture fillings, density, apparent porosity, and optical diffraction patterns. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic velocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Conclusions are that some relation appears to exist between compressive strength and the following properties and features for all specimens: dynamic Young's modulus, sonic velocity, density, rock composition, slope of velocity curve, composition and fabric of fracture fillings-veinlets, and apparent porosity. There appears to be some relation between compressive strength and Shore scelerscope hardness for the quartz monzonite (San Manuel). A relation appears to exist between texture and compressive strength and the extent of failure on fracture fillings for schists, gneiss, and fine-grained granite (Climax). The amount of swelling clays (montmorillonite, hydromicas, etc.) present in the rock and the relative number of fractures in which they constitute of major portion of the fracture fillings are related to the strength of the rocks. Possible tests for checking the amount of these clays present is presented including saturation, dyes, and X-rays. A useful index relating to rock strength, as revealed in this study, is the presence of swelling clays in detectable abundances. These clays can be detected in the field with a simple wetting and striking test; in the laboratory they can be detected by X-ray and dye methods.

Jan 1, 1974

Falls of ground (FOG) still account for around 35 per cent of all fatalities in underground southern African mines. To help reduce FOG, appropriate support technology needs to be implemented, and a mindset and cultural change are required to make a significant change. Discipline plays a major role and needs attention, whilst appropriate first-world support technology is available to assist in the reduction of injuries and the improvement of productivity. Section 54 mine stoppages due to FOG are costly. Appropriate support should reduce these unnecessary stoppages. Coal mining has adapted leading support technologies over the years. Platinum and chrome mines have shown significant moves towards adopting leading and appropriate support technologies, seeing noteworthy changes in injury statistics for the better. In typical conventional underground mining operations, the use of temporary support components offers some protection to workers while the permanent and generally more elaborate support systems are installed or constructed. Nonetheless, FOG continue and still result in injuries to people. The author wishes to explore the options and practicality of making use of new-generation support products and technology to provide not only safer support operations, but to also enhance productivity at the working faces. This paper will examine the use of appropriate support technology as a means to making the working stope or development end a safer and more productive workplace.

Jan 1, 2012

By AIME AIME

EDWIN W. KEMMERER, professor of international finance at Princeton, in a speech before a banking conference at Urbana, Ill., on Nov. 26, stated that the increase in the store of gold held by the United States is not so alarming as it appears on the surface. Excerpts from his address, as reported by The New York Times, follow: "It is significant . . . that the value of gold as expressed in its purchasing power in the United States during the last half-dozen years has been higher than at any other equivalent period since our records began 140 years ago. Our so-called 59-cent dollar today buys about 25 per cent more goods at wholesale than did our old dollar in the prosperous year 1926, and an ounce of gold will now buy considerably more than twice what it did then. This present high value of gold is one reason for its recent large production.

Jan 1, 1941

By A Walker

The presence of high noise levels in many industries, together with the fact that countries are becoming increasingly concerned with the health of its citizens, has contributed to the importance of the problem of hearing loss. This problem has become the focus of scientific research, law and medicine, and the object of this thesis is to present the means whereby noise may be detected, with its resulting effects and possible means of control, in mining operations. 0BJECTIONABLE noise is a particularly prevalent by-product of the mining industry, and, al-though a dangerous noise level has been recognized, it is believed that at no time now, or in the future, will it be possible to enumerate a single over-all decibel figure at which hearing impairment will oc-cur. Individual susceptibility must be recognized in any study of occupational loss of hearing aimed at the setting of standards and criteria for industrial noise control.

Jan 1, 1963

By Clifford H. Summers

This report describes an experimental program which we conducted on behalf of the U. S. Bureau of Mines, to select from currently available materials two novel systems of construction for air-restraining bulkheads to be used in control of radon-polluted air in underground uranium mines. The program included both laboratory and field tests, the latter conducted in a portion of an operating mine owned and operated by Union Carbide Corporation at LaSal, Utah. The test site was a worked-out, double entry stope having a Volume of about 2000 cubic meters, and was located immediately adjacent to an exhaust airway. The bulkheads were constructed of 15 cm x 1.5 cm timber uprights, 5 cm x 15 cm horizontal members supporting a close-fitted 13 mm plywood curtain-wall., which was covered with a low-permeability membrane to seal in the radon-polluted air. The two membrane materials selected for testing were chosen from a list of twenty-two potentially acceptable candidates using criteria such as strength, flammability, ease of application, adhesion, radon permeability, and elasticity. Thirteen of the candidates were tested in our laboratories for adhesion to plywood and to both wet and dry concrete (simulating wet and dry mine rock surfaces), and for their general physical properties, including radon permeability. The final selections made by the Technical Project Officer, and based on our recommendation, were a pre-formed ethylene propylene diene monomeric rubber (EPDM) membrane 1.12 mm thick, normally used as a roof sealant in industrial construction, and available from Carlisle Tire and Rubber Co., Division of Carlisle Corp., Carlisle, PA, and Aquafas 48-00, a water-based mastic used in a wide variety of commercial applications and available from H. B. Fuller Co., Foster Products Division, Spring House, PA. The EPDM membrane was applied as a single sheet, laminated (dry) between two layers of plywood, and the Aquafas was applied both by troweling and spraying onto a plywood surface. In the field test, radon concentrations were continuously measured before, after, and in the trapped air behind each bulkhead. Temperature, pressure, and velocity of the air in the adjacent airway were also measured and recorded continuously. Radon fluxes at the rock/air interface and through the bulkheads themselves were measured manually on a frequent basis. All continuously acquired raw data were recorded automatically on two USBM Data Aquisition Systems (DAS), and the raw data were converted into engineering units and recorded on magnetic disks by a specially programmed microcomputer that was interfaced with the DAS's. Relatively clean (i.e. low radon concentration) air was pumped into a point near the face of one test bulkhead from a location 170 meters away through vent bag. Several air curtains and two air-restraining bulkheads were erected in passageways adjacent to the test area in an effort to control both velocity and radon concentration of the air flowing past the bulkhead faces. An average concentration of approximately 500 pCi/liter at a flow of 550 m3/minute was attained as the background concentration against which leakage through the bulkheads was measured. The entire field test period extended from October, 1981 to March, 1982, a total of six months, and was subdivided into seven successive time periods: 1) site preparation 2) background measurements prior to bulkhead construction 3) passive restraint, with bulkheads in place and totally sealed 4) open bleeder period of natural convection ventilation in and out of the bulkheaded area through a 10 cm (diameter) opening, with connecting tubing; leading into an Exhaust airway 5) open bleeder period, having forced exhaust through a 1.0 cm opening using a servo-controlled fan 6) charcoal trapping period, using the servo-controlled fan to exhaust air through the charcoal traps, to test the effectiveness of such traps in removal of radon from the exhausted air 7) site decommissioning Each of the two systems tested, one incorporating the pro-formed EPDM-rubber membrane and the other utilizing Aquafas 48-00, was assessed for effectiveness in controlling radon-polluted air by observing the change in the radon concentration in the ventilation air flowing continuously over the surface of each bulkhead. The sensitivity of the observed measurements was limited by the volume flow-rate of the ventilation air and the radon concentration in that air. The data would indicate that the observed increments in radon concentration in the ventilation air moving across bulkheads B-l and B-2 were essentially zero within the limits of sensitivity of the measurements. Data from radon flux measurement taken both on the sealed ribs adjacent to the bulkheads and on the bulkheads themselves did not differ significantly from blank data.

Jan 1, 1982

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

Reynolds Metals Company announced plans to increase its rate of production of primary aluminum by 17 thousand tons per year by the end of February. Other producers were expected to increase operating rates during the first quarter of 1976 (see table 10 pg. 29). CHROMIUM -Under the Trade Act of 1974, a petition was filed July 16, 1975, with the U.S. International Trade Commission (ITC) by the Tool and Stainless Steel Industry Committee for Import Relief and the United Steelworkers of America, AFL-CIO, for import relief for certain stainless and alloy tool steel products. The Commission determined on January 16, 1976, in a report to the President, that increased quantities of imports of stainless steel sheet and strip, plate, bar, and rod and alloy tool steel except ingots, blooms, billets, slabs, and sheet bars were a substantial cause of serious injury or threat thereof. The Commission recommended import quotas for the period 1976 through 1980. The President has 2 months in which to act, with his decision subject to a Congressional override.

Jan 1, 1976

By G. Warren

"In the past, smelting and refining of the precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. This philosophy is changing however, as economic and environmental pressure are forcing a re-evaluation of all aspects of gold mining and milling.This paper describes and evaluates three furnace technologies available and used by precious metal operators. The operation of arc, induction, and reverberatory furnaces are discussed and their strengths and weaknesses with respect to capital cost, impurity removal, slag quality, and environmental concerns highlighted.INTRODUCTIONIn the past, smelting and refining of precious metals recovered from ore has been generally looked upon as a small and relatively minor component of the business of gold mining. This is not surprising when one considers that the manpower, space, and capital components of a gold refinery at an operating mine can be several orders of magnitude smaller than other unit operations at the same location. Generally, gold producers will spend a great deal of effort to squeeze the last drop of efficiency out of a leach or grinding circuit via simulation or testwork but will design and build the refinery based upon past practices or industry standards. That past practices or industry standards will provide a functional refinery is undisputed; that this philosophy achieves the efficiencies that are possible or demanded in other plant operations is debatable.Environmental and worker hygiene requirements are considerations as well. Pollution control equipment can become a substantial contributor to both the capital and operating costs of a refinery and furnace selection has a marked influence upon the type and cost of this equipment. Slag characteristics and subsequent processing options available also play a role in furnace selection as precious metal slag losses and the recovery effort can greatly influence the cost / benefit analysis of a particular technology."

Jan 1, 2001

By N. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract J0377014, "Development and Evaluation of Noise Control Techniques for Taconite Processing Equipment." Three areas of taconite processing equipment, grinding mills, fine screens, and crusher screens have been investigated. Extensive noise and vibration measurements have been made on grinding mills in which the process parameters that affect mill noise have been identified, and the level of shell impact noise around the mill defined. A multiplexing telemetry system was used to obtain shell vibration measurements from a rotating mill. Mill noise control methods were investigated and a partial mill barrier was built and tested on a semi-autogeneous mill. A noise reduction of approximately 3 to 6 dBA was achieved on the falling side of the mill. The use of rubber mill liners on autogenous mills has been evaluated. The noise sources on fine screens have been quantified, and noise control treatments developed. Noise reductions of 11 to 13 dBA were achieved at positions around the fine screen and some in-service testing has been done. Noise measurents of crusher screens were obtained and noise control through resilient screen decks appears to hold the most promise. Additional benefits might be lower life-cycle cost, since the service life of resilient decks is claimed to be longer than steel.

Jan 1, 1983

By Ping Zhang, Xu Ma

Perturbations arising from mining operations significantly affect the stability of rock masses, and the influences aggerates with the rapid increase of mining-operation depths during recent years. The subsurface structures with major discontinuities subject to seismic hazards resulted from the shear-slip behaviors of rock masses. In order to identify the shear-slip regime of discontinuities and calculate seismic moment and seismic energy involved with shear-slip behaviors, we use discrete element modeling to study the shear slip failure along discontinuities in an underground mine. The recorded characteristic and properties of sub-contacts in DEM provide a basis for computing and visualizing the temporal and spatial distribution of seismic moment and seismic energy with mining operations. We computed the seismic energy and seismic moment using the numerical modeling method and the analytic method. We compared the result of summing seismic energy and seismic moment from the subcontacts of numerical models and the result of the analytic method. We confirmed that this tool can be used in comparative analyses. We also found that seismic moment and seismic energy, associated with shear stress drop and shear displacement increase, accumulate in the vicinity of major discontinuities. Mining operations at a greater depth cause greater changes of seismic moment and seismic energy, leading to a higher risk of inducing seismic hazards. Quantifying seismic potential using discrete element modeling can greatly facilitate the investigation of instability of geological discontinuities and thereby can help estimate the potential of seismic hazards.

Jan 21, 2023

By Fujio Ishii

The deoxidation of liquid nickel and nickel binary alloys with silicon has been determined at temperatures between 1500°C and 1650°C using quartz crucibles in order to investigate the deoxidation of nickel based alloys. The equilibrium constant of the deoxidation reaction in liquid nickel and the effects of the different alloying elements such as chromium, molybdenum, tungsten, iron, cobalt and coppcr on the activity coefficient of oxygen in liquid nickel have been established.

Jan 1, 1993

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By B. Comley, M. C. Harris

There is as yet no accepted method of predicting flotation frother performance in plant processes based on laboratory scale characterisation techniques. This paper investigates the use of dynamic surface tension, using the maximum bubble pressure method, as a means of evaluating frothers and frother mixtures. An adsorption model is presented, which has been used to quantify the role of frother type and concentration during frother bubble interaction, based on the correlation of model parameters to physical frother characteristics. This approach was found to provide useful insight with respect to blending and selection of flotation frothers to meet specified flotation performance criteria.

Jan 1, 2001

By Graham A. Davis

?The ideas of economists and political philosophers, both when they are right and when they are wrong, are more powerful than is commonly understood. Indeed, the world is ruled by little else. Practical men, who believe themselves to be quite exempt from any intellectual influences, are usually the slaves of some defunct economist. Madmen in authority, who hear voices in the air, are distilling their frenzy from some academic scribbler of a few years back. I am sure that the power of vested interests is vastly exaggerated compared with the gradual encroachment of ideas. . . . But, soon or late, it is ideas, not vested interests, which are dangerous for good or evil.? John Maynard Keynes The General Theory (1936) Policy analysts, economists and others have tradition-ally considered mining and mineral wealth a boon, providing rich countries with the resources needed to sustain their modern industrial economies while helping poorer countries generate the foreign exchange, tax revenues and other assets necessary for economic growth and development. Nevertheless, this conventional view has always had its critics.

Jan 1, 2008

By B. P. von der Heyden, T. Blenkinsop, A. Mamuse

Zimbabwe hosts a varied array of coloured gemstones. With the exception of emerald deposits and several world-class pegmatites, few of the gemstone occurrences have received detailed attention from the scientific or mineral exploration communities. In the present contribution we summarize the status of knowledge of the gemstone deposits and occurrences in Zimbabwe, paying particular attention to the geological settings in which they were formed. Synthesis of this regional geological approach reveals that there may be significant exploration potential for further gemstone occurrences, particularly in the extensive pegmatite fields and in Al-enriched orogenic belts that have undergone greenschist to granulite facies metamorphism. Further socio-economic and developmental initiatives will aid in optimizing the value generation from this important sub-sector.

Feb 12, 2024