Search Documents

By C E. J de Ronde, J G. Scott

Economic gold mineralisation was discovered at Round Hill by Homestake NZ Limited in 1984 and was subsequently put into production by Macraes Mining Company Limited (MMCL) in 1990. The total mineral resource in 1990 was estimated at 41.4 Mt @ 1.42 glt at a 0.7g/t cut off, for 1.8 Moz of gold. Since project start up the mill has been upgraded twice to increase throughput and reached its current capacity of 3.2 Mtpa. At 31 December 1996, a total of 16.2 Mt of ore at average grade of 1.73 g/t has been excavated, yielding 655,000 oz of gold. MMCL began exploration along the Hyde Macraes Shear Zone in 1994. Since 1994, exploration has been successful with the discovery of over 3.5 Moz of gold. The resource now stands at 110 Mt @ 1.46 g/t gold for 5.1 Moz. This success has led to a planned expansion of the processing capacity to 9 Mtpa with the building of a new 6 Mtpa processing plant.

Jan 1, 1997

By M. Gous

Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC-arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC-arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilization and furnace stability, complemented by continuous improvement drives, will be thevehicle to drive performance in the short-term, with longer-term performance enhancements due to strategic process development. Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC-arc furnace, titania slag, pig iron

Jan 1, 2006

By L. Betteridge, A. Marks

"An OK 300 cu. ft. Skim - Air cell was installed at the HBM&S concentrator in Flin Flon in 1987. Since that time, 3 additional OK Skim - Air cells have been installed in HBM&S concentrators. The cell treats a coarse 70% solids slurry with a residence time of 2.5 minutes. The product from the cell (a unit cell type application) is a final grade copper concentrate with high precious metal values. Since its installation, the cell has improved gold recovery by 10 - 15%. Process variables such as circulating load, pH, froth depth, feed size, and reagent additions all have an effect on the operation of the cell. Maintenance on the cell has been minimal. Initial operating problems involving level control have been significantly reduced and operations are now relatively trouble free. Although very successful at Flin Flon, site specific operating circumstances will determine the suitability of this cell. INTRODUCTIONHudson Bay Mining and Smelting operates four concentrators in Northern Manitoba. Three treat copper-zinc ores, the fourth mills a copper-nickel ore. The Flin Flan concentrator operates two circuits in parallel which treat copper and zinc ores from the Trout Lake and Callinan mines. Both circuits in the Flin Flan mill have Skim-Air cells integrated into the grinding circuits.The Trout Lake cell was installed first and had a payback period of a few months. Required modifications to the cell were made to enhance its performance. These included changing the discharge valve size, tuning the level controller, and installing an insert into the rubber valve sleeve to increase its wear life. The payback period on the Callinan cell was significantly reduced because these modifications were completed prior to its installation.The cells produce a final grade copper concentrate and since their installation gold and silver recoveries to the final copper concentrate have increased significantly. Operating parameters such as coarseness of cell feed dictate the metal recoveries and froth depth determines the selectivity of the cell and therefore the grade of the concentrate.The Skim-Air cell can be suitable in applications where a final product is generated. However, when a bulk concentrate, which requires further separation, is produced, the coarseness of the product may not make it amenable to conventional flotation.The Flin Flan mills Skim-Air cells have worked exceptionally well with little maintenance required."

Jan 1, 1991

By D. R. Dollnar

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2002

By O. Worku, J. H. Masliyah, Z. A. Zhou

ABSTRACT The viscosity of concentrated kaolinite or illite clay in aqueous suspensions was measured in the presence and absence of a small amount of montmorillonite (<1 wt%). To avoid solids settling and to increase the sensitivity of the suspension viscosity measurements, solids concentrations higher than 38 wt% were used. The pH of the suspensions and the concentration of calcium and bicarbonate ions were found to significantly impact the viscosity of the clay suspensions. The results showed a significant increase in the viscosity of kaolinite suspensions with the addition of as low as 0.25 wt% of montmorillonite on a solids weight basis. In addition to illustrating the role of water chemistry in modifying slurry rheological properties, our study demonstrated that viscosity measurement could be a simple, yet sensitive technique for determining the content of smectite clays, such as montmorillonite, in a complex mix of various types of clay.

Jan 1, 2012

By Kush Patel, Gary Cavanough

Mining operations consume over 2.5 Billion Australian dollars’ worth of bulk explosives annually (Richardson, 2018). Despite the large volume of product used, current practices only conduct a cup density test of the product being used. Explosive products are made up of a number of components, each with an effect on the performance of the explosive. This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser. Through a total of 60 tests carried out on 10 different bulk explosive products the average error of each method was determined, the BEA presented an average error of 0.11%, whereas, the wet chemistry method presented an average error of 1.90%. This is a significant difference when considering the importance of formulation of explosives. Further investigation into the capabilities of the BEA are also presented in this paper.

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

By E. F. Perry

Simulated weathering tests are used to estimate leachate quality of rocks containing varying concentrations of pyrite and carbonates at mines. This study reports the inter-laboratory results from the third phase of a three part effort to develop a standardized, reproducible simulated weathering test for coal mine overburden. Initial development in phases I and II included evaluation of different test apparatus, effects of particle size, gas composition, leaching frequency and other variables. Phases I and II results are reported by Brady et al (2004) and Hornberger et al (2004). In Phase III, a standard column leaching protocol was used by eight commercial, government and university labs to test five rocks of different lithology, pyrite and carbonate content. Ideally, a simulated weathering test should have three characteristics to be useful in mine drainage studies. These include the capability to produce repeatable results, accuracy in simulating field conditions, and a concise test protocol of weeks to a few months. Simulated weathering, or kinetic testing, produces an effluent that simulates mine drainage composition. This can be beneficial for predicting mine drainage quality in comparison to whole rock analyses. The effluent may be tested for the same water quality parameters as the drainage produced during mining, such as pH, acidity, alkalinity, sulfate, iron, manganese, aluminum or other parameters. If the physical, chemical, and biological conditions of the kinetic tests are representative of those found in the mine environment, leachate composition may be used to estimate the water quality parameter concentrations produced during mining. Hornberger and Brady (1998), and Geidel et al (2000), compiled comprehensive chapters on kinetic tests for mine drainage prediction. These sources included: (1) a chronology and synopsis of scientific literature on these kinetic tests as they have developed over approximately 50 years, (2) discussion of the influence of physical, chemical, and biological processes, and (3) general guidelines for test procedures, data interpretation, and recommendations for further research to develop standard methods. Most of the kinetic test methods in use today were substantially developed and applied more than 40 or 50 years ago, including leaching columns (Braley, 1949), humidity cells (Hanna and Brant, 1962), Soxhlet reactors (Pedro, 1961), and field scale tests (Glover and Kenyon, 1962). . The most commonly used kinetic tests for mine drainage prediction are leaching columns and humidity cells. While these kinetic test methods and others have been used in hundreds of mine drainage studies as shown in Hornberger and Brady (1998) and other references (e.g. Sorini, 1997), they have rarely been used in coal mine permitting by either regulatory agencies or the mining industry. The major impediment to routine use of kinetic test methods is the variation in the design and operation of these kinetic tests, and lack of a standardized, accepted (e.g. by EPA or ASTM) test method. Interpretation and data comparison from different studies can be difficult. METHODS Five rocks of varying lithology, mineralogy, carbonate and pyrite content were collected in bulk from Pennsylvanian age coal measures in Pennsylvania, West Virginia and Indiana. Mineralogical composition of the samples was characterized in detail by Hammerstrom et al (in press) using optical, X-ray diffraction, scanning electron microscopy and electron microprobe methods. Acid Base Accounting (Sobek et al 1978; Skousen et al, 1997, Kania, 1998) was performed on bulk samples for % total sulfur (%S) as a measure of pyrite and potential acid generation, and Neutralization Potential (NP) as an index of carbonate content. A modified NP test, following the procedure suggested by Skousen et al, 1997 was also conducted for four of the five samples. The modified NP test accounts for initial acid consumption, Fe oxidation, and subsequent Fe hydrolysis by the iron carbonate mineral siderite. Siderite, even though it is a carbonate gives zero net alkalinity. Lithologic, Acid Base Accounting and general mineral composition data for the five rocks are shown in table 1 (see Appendix). Whole rock elemental analysis for major and trace elements was conducted on a sub-sample of each rock type. One laboratory was contracted to mix, homogenize, and size the bulk samples and prepare sub-samples for all the participating labs. Splits were sent to eight labs, and each organization was provided a detailed set of instructions for column assembly and leaching procedure. The protocol was developed based on results from phases 1and 2 of this study. The principal features of the column assembly are: a specific composition of particle size by weight (table 2), weekly leaching cycles, and incubation under humidified air containing 10% CO2. Figure 1 shows the column construction. [ ] The particle size distribution of the crushed rock sample is largely an artifact of the crushing process, rather than a natural systems process like the particle size distribution of a soil or an unconsolidated sedimentary deposit. The standardized particle size distribution, shown in Table 2, promotes operational consistency of the weathering test procedure, and provides better control over reaction kinetics. Large amounts of fine particles within specific zones of the leaching columns have been found to impede uniform fluid flow and/or gas flow (Hornberger and Brady, 1998). Regarding reaction kinetics, the importance of surface area to volume ratios has been described in a previous phase of this study (Brady et al., 2004), and significant differences in crushed particle size distributions and effective surface areas were found among the lithologic units. Standardizing the particle

Jan 1, 2009

By M. Botz

Anatolia Minerals Development Limited (AMDL) is constructing the Çöpler Gold Project in eastern Turkey and commenced mining in the fourth quarter of 2009 with gold production scheduled to begin in the fourth quarter of 2010. The project is a 15,500 tonnes/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life approximately 40 million tones of ore will be placed on the leach pad, which will contain about 35,000 tonnes of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the mine life. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By Roger J. Higgins

Papua New Guinea is a country on the cusp of development, struggling to find a balance between the demands of national and regional growth, landowner expectations and the maintenance of cultural identity. Ok Tedi Mining Limited is the single largest contributor to PNG?s economy, representing about 10 percent of the country?s GDP. OTML is demonstrating that business and country risk can be managed through effective, respectful partnerships with local communities. OTML?s relationships with the communities of PNG?s Western Province are multifaceted. Communities have borne the brunt of the mine?s environmental impact, yet have benefited enormously from the development that the mine has brought. Importantly, the PNG economy is now the ultimate beneficiary of more than four-fifths of the dividends from the mine, the majority of which are held in trust for long-term sustainable development projects. The paper describes how OTML works with the Western Province communities to create a secure operating environment that recognizes the people?s aspirations for development and self-determination.

May 1, 2002

The Skorpion Zinc Project demonstrated the viability of the production of zinc from non-sulphide (commonly called ?zinc-oxide?) ores, using the leach/solvent extraction/electrowinning process route. The success of Skorpion raised the profile of a number of other zinc oxide deposits, considered to be similar. However, a study of three such deposits demonstrates that the application of whole-ore-leaching may be limited and that the concentration of zinc, or at least the separation from acid-consuming gangue minerals, prior to leaching is essential to the successful recovery of zinc from these deposits. The recovery of zinc is dependent on an understanding of the geology of the deposit, the mineralogical association of zinc minerals with gangue minerals (Boni, 2005) and limitations of mining practice. Flow sheet development and the associated metallurgical test work to derive an economically viable treatment route from two of these deposits are discussed. Key parameters affecting zinc recovery by gravity separation and flotation are presented, demonstrating that even minor differences in mineralogy have a profound impact on zinc recovery and reagent consumption. The study also deals with the determination of appropriate design parameters through metallurgical mapping of the dense media separation process.

Jan 1, 2008

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that&apos;s proportional to the noise level.

Jan 1, 1975

By Christian Maguire

The presence of hydrogen sulphide in sewerage systems leads to severe concrete corrosion. Acid causes breakdown of the concrete matrix, and attacks reinforcement. Older sewer systems under acid attack are often found to be acutely corroded, sometimes after short operational periods. Consequently secondary liners are now almost always used. Polymer concrete is extremely acid resistant and if used in segmental linings can forgo the need for a secondary lining. Combined with fibers and/or GFRP rebar Polymer Concrete can produce a very strong acid resistant lining, saving considerable time in the installation of additional liners. This paper explains the problems and advantages of using Polymer concrete in segmentaly lined wastewater tunnels, addressing areas of design, cost, and programming.

Jan 1, 2008

By G. R. Lane, A. Vermeulen, S. van de Venter, S. Bhoowanpursadh

Over the past two years Anglo Platinum made use of the specialist skills of Cyest Corporation to develop a Mine Optimization Tool (MOT) to enhance the current suite of in house mine planning tools and processes. The application was built in a multidimensional modelling environment developed by Cyest called CarbonL. This has allowed complex modelling that is transparent to the business users and therefore is not prone to the ?black box? approach that generally exists with these types of complex tools. The purpose of the MOT is to have an integrated software tool that can schedule production activities by half level for a shaft complex, while at the same time integrating the economics concomitant with that schedule. The tool allows the user to configure all activities relevant to the selected mining method, define the mine design parameters and geological parameters, define scheduling rules and then schedule all activities. This allows the user to test various production strategies and schedules very quickly and easily in terms of shaft value, costs and revenue profiles, labour complement and production ramp up so as to determine the option that best fits the overall strategy. This allows assessments of multiple scenarios in a relatively short period of time, after which only the best option is taken forward for graphic design and scheduling. This paper discusses briefly the rationale behind the Mine Optimisation Tool and the underlying workings of the modules that comprise the tool. It also covers the life cycle of this tool from the original prototype through to the final Mine Optimisation Tool software and discusses the positioning of the final tool.

Jan 1, 2007

An examination of the Census of Fatal Occupational Injuries (CFOI) data for the period 1992-1995 shows that 659 fatalities occurred in the mining industry as defined by the SIC. Oil and gas accounted for slightly more than one-half of all fatalities (figure 1-1). The coal industry had the highest fatality rate for the 4-year period, with 35.6 deaths per 100,000 full-time workers, followed by metal (23.1 per 100,000), oil and gas (23.1 per 100,000), and nonmetal (20.1 per 100,000). The fatality rate for all U. S. industries during this same period was 5.1 per 100,000 full-time workers. Figure 1-2 compares the fatal injury rates by year for the four major industry sectors of mining to the fatality rate for all industries combined. Figure 1-3 compares age-specific fatality rates in the mining industry to those seen for U. S. industry as a whole. Fatality rates for all industries combined were lowest for young workers and steadily increased in relation to workers&apos; ages. In the mining industry, fatality rates by age group show a U-shaped curve. Young workers under 20 years of age had the highest injury rate (54.6 per 100,000), followed by workers aged 20-24 (50.8 per 100,000) and workers over age 65 (37.7 per 100,000). Table 1-1 shows the distribution of injuries by type of injury event. The mining industry, in comparison with all industries, had a considerably larger proportion of fatalities classified as caught in or crushed by collapsing materials (9.1% and 1.9%, respectively) and fires and explosions (10.0% and 3.1%, respectively). Transportation events comprised the largest proportion of fatal injuries in both the mining industry and all industries. Within the mining industry only, transportation accounted for the largest proportion of fatalities in all mining sectors except coal. A more detailed examination of the transportation events within the mining industry showed that highway incidents (50.5%) were the most common, followed by nonhighway incidents (22.2%), pedestrian incidents (10.6%), and those incurred during rail, water, and air transport (15.7%). Incidents involving caught in or crushed by collapsing materials comprised a higher percentage of injuries in the coal and metal sectors, while fall-from-height incidents were more frequent in the oil and gas sector. The classification system used in CFOI for type of injury event is not compatible with any variables contained in the MSHA data; therefore, direct comparisons are not attempted. [ ]

Jan 5, 2000

By H. Lyn Bourne

This is the seventh annual tabulation of royalty information. It is also the first year in which some data have been deleted to make room for new data. The concept of royalties evolved from a time when the government owned all of the land, including mines, to the situation where free miners won the right to claim minerals but paid a portion of their production to the royal treasury. Today, a mineral royalty is a payment to the owner of the mineral rights for the privilege of producing the mineral commodity. However, some people incorrectly believe that the selling price and the royalty are the same thing. The contract between the owner (lessor) and the mining company (lessee) is the mineral lease. Some clauses that are common to mineral leases include: identification of property, granting clause, reservations, definitions, royalty rate, taxes and title, indemnity, termination, inspection, assignability, successors, and reclamation. There often are variations in royalty rates for a given commodity that reflect differences in location, quality, market conditions or public versus private ownership. History In the time of ancient Rome, the government owned the mining properties by virtue of conquest. It would lease the mines to favored citizens who would pay rent to the State. Various conditions of sovereign ownership of both land and mineral rights continued in Europe until the Renaissance. As the laws evolved for land ownership by private citizens, the concept that minerals belonged to the State (King, Crown, sovereign) continued until about the 15th century. Free miners challenged the notion of sovereign ownership and won the right to discover and claim minerals. But a portion of their production had to be paid to the sovereign - a royalty. So, the original concept of a mineral royalty was a tax on production that was due to the Crown or Church. The term mineral royalty, as it is known today, is a payment to the owner of the mineral rights (formerly the royal owner) for the privilege of mining and producing the mineral commodity. The owner of the mineral rights, the lessor, and the mine operator, the lessee, enter into an agreement to mine the property. The agreement is the lease. While this concept is common, there are some who do not understand that the royalty is a portion of production paid to the owner as agreed on in the lease document. This author has seen reports where the selling price of a commodity has been quoted as the royalty. ("They get 70 cents a ton royalty at their pit and the guy down the road only has a 65 cent royalty.") These reports have been authored by people not familiar with the mining industry. Lease clauses In addition to the amount to be paid the lessor, there are several other items to be addressed in the lease agreement. The following list may not be all inclusive, but briefly describes most of the common clauses any good mining lease should contain. Identification: This opening clause names the owner (lessor) and the operator (lessee), the address of each, and gives the legal description of the property. Granting clause: This part of the lease gives the time period or duration of the agreement and information about renewal periods. It also has language about the exclusive right of the lessee to mine the property. Reservations: If the owner wants to exclude any portion of the property or set some specific conditions about the operation, there needs to be a clause that describes these reservations. Definitions: This section should address some of the technical terms that the lessor may find confusing - short tons versus cubic yards, dollars versus percentage of average selling price, any escalator indices such as consumer price index or producer price index, and material mined versus material sold. Royalty: This section spells out what the royalty rate will be, how often it will be paid, if there is an annual minimum, the pay dates, and how the records will be kept. This section also describes the conditions under which the lessee is exempt from the annual minimum - natural disasters, strikes, governmental actions, or other causes referred to as force majeure. Taxes and title: The lease needs to identify who is responsible for the property taxes, severance taxes (if applicable), and other taxes that relate to the mining activity - taxes on equipment, improvements, or stockpiles. This is a good place in the lease for the owner to certify his ownership of the property and its mineral rights and also certify that no other leases are in effect. The lessees may want language that allows them to pay mortgages or other debts on the property to keep their lease in effect. Indemnity: This portion of the lease identifies that the lessee assumes the risks for lessee&apos;s mining operation. Lessor should expect indemnification by the lessee through standard insur¬ance policies - workers compensation, liability and property damage. Termination: Both the lessor and lessee want language that will allow them to terminate the lease. This section of the lease describes the conditions under which one of the parties may terminate the lease (failure of the

Jan 1, 1989

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988