Search Documents

Dynamic Simulation of an Alumina Refinery

Sep 13, 2010

By Peter M. Herzig

In 1994 and 1998 the German research vessel R/V Sonne undertook detailed mapping and sampling of the largely uncharted offshore areas of the Tabar-Lihir-Tanga-Feni island chain in the New Ireland Basin of Papua New Guinea. The New Ireland Basin occupies a fore-arc position with respect to the formerly active Manus-Kilinailau arc-trench system and hosts a series of Pliocene to Recent alkaline volcanoes which are built on rifted Miocene sedimentary basement. Several of the volcanoes possess high-level porphyry stocks and active geothermal systems, including gold-depositing hot springs and the giant (40 million ounces) Ladolam gold deposit on the island of Lihir. On the southern flank of Lihir island, a group of three volcanic cones were discovered at water depths from 1.000-1.500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered volcanic rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts (ankaramites), porphyritic phlogopite basalts, and trachybasalts. Unusual gold-rich hydrothermal precipitates were recovered from the summit of the 600 m high Conical Seamount located only about 10 km south of Lihir Island. 1200 kg of sampled material systematically collected with a TV-guided grab from the top plateau (150 x 200 m, 1.050 m water depth) are intensely mineralized with pyrite, marcasite, minor sphalerite, chalcopyrite, galena, tennantite/tetrahedrite, and orpiment/realgar together with traces of anglesite, cerrusite, and amorphous silica in stockwork-like veins. Bulk samples of the vein mineralization consist mainly of clays, silica, and disseminated sulfides, and have an unusual high gold content ranging from 1.2-44.0 ppm Au. In some of these samples, grains of native gold (about 1 micron in diameter) were identified by SEM in pyrite and sphalerite. The gold-rich material also contains high concentrations of silver (up to 1000 ppm) and typical epithermal elements such as As (2.6 wt.%), Sb (0.2 wt.%), and Hg (34 ppm). Similar to epithermal deposits on land, which usually have only low base metal contents, the samples from Conical Seamount contain only minor amounts of Zn (max. 4.5 wt.%), Cu (2.0 wt.%), and Pb (2.0 wt.%). Many of the samples recovered from Conical Seamount are virtually identical to the gold ore at Lihir.

Jan 1, 1998

Advances in technology have led to larger and deeper open pit mines and, consequently, also increased the potential economic impact associated with slope failures. If the ultimate aim of mining operations is to maximise project profit, it is surprising to see related research activities have mostly been focusing on technical areas such as slope stability modelling, but with limited studies conducted to date to assess the relationship between geotechnical uncertainties and economic risk. Given most major decisions in the mining industry nowadays are made by management staff with financial background, any design approach that would help to link slope stability analysis results with monetary values would no doubt enhance communication between geotechnical practitioners and decision makers. This paper presents a study which assesses economic impact of slope failures to assist in mine planning. The study also estimates the impact of slope failures on project value, which would enable economic risks associated with pit slope designs to be closely examined. The proposed risk assessment techniques, used by financial institutions for many years to assess portfolio risks, can assist geotechnical practitioners in quantifying risks of slope failures. Risk-adjusted concepts are also suggested to assist management in selecting a slope design with optimal risk and return ratio.

May 1, 2010

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

By Bertrand L. Johnson

The major elements essential to plant growth are nitrogen, potassium, and phosphorus. These three constituents of the soil are removed relatively rapidly by growing crops and consequently are the main constituents of commercial fertilizers. Scientific studies, however, have progressively revealed the fact that a number of other plant foods, many of which are not necessarily supplied in commercial fertilizers, are necessary to assist plant growth and fruit production and that soils deficient in certain of these minor elements may be made much more productive by adding them. The farmer looks to the miner to furnish most of the elements requisite to plant growth, which have to be supplied through the medium of fertilizer additions. It follows that the mining industry should keep an eye upon developments in the fertilizer industry and in the results of soil studies as a possible outlet for mineral products. The important industries engaged in the production and marketing of the three principal pant nutrients have already been described in Bureau of Mines publications .3 The present paper discusses the commercial implications with respect to other elements that are now employed as soil additions.

Jan 1, 1935

By Joe Holmes, Peter Langlois

"Falconbridge’s Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region, has been in operation since December 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,000,000 tonnes per year. Optimization of the ABC grinding circuit has proven to be the most challenging component of this capacity increase. Concurrent flotation circuit modifications have allowed concentrate grades to increase from 16 to 18 percent nickel, while maintaining recoveries. Concentrate drying problems encountered during the first 15 months of operation have been addressed through equipment upgrades. The challenges associated with surface deposition of filtered tailings in an arctic environment are now better understood, and detailed design of the progressive reclamation cover is underway.GRINDINGCircuit OverviewOre from open pit and underground mining operations is introduced to the underground ore handling system via surface and underground truck dumps. Two underground bins with a combined capacity of 4000 tonnes provide roughly a day of live capacity for ore storage. Ore from the two bins is conveyed to a 150 tonne surge bin immediately ahead of the grinding circuit in the concentrator.The Raglan grinding circuit has a conventional ABC configuration (Figure 1) with a design capacity of 100 mtph (800,000 tonnes per year). The 24’ AG mill is powered by a 3000 hp motor with variable speed drive. AG discharge is sized on a 8’x16’ single deck vibrating screen, with screen oversize recirculating to a 5 %’ short head cone crusher (400 hp) before returning to the AG mill. Screen undersize is combined with ball mill discharge to feed up to 5 15” Krebs hydrocyclones. The ball mill is a 14’x 21’ overflow mill driven by a 3000 hp motor at 73% critical speed. Target Pgo for the grinding circuit product is 65 microns"

Jan 1, 2001

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

DML Resources Limited - Mining Division produced over 50 000 oz of alluvial gold in the 1995 - 1996 year from five operations located in the West Coast and Otago Regions on the South Island of New Zealand. DML Resources Limited - Mining Division have a twenty year history of alluvial gold mining development in New Zealand. Recent expansions have seen the establishment of two operations in Chile whilst exploration continues in Bolivia, Peru and Argentina. The overseas growth is based on a stable production base in New Zealand focussed on the West Coast and Southland/Otago present and future operations. DML Resources consider that the mining potential in the Arahura Valley on the West coast will be fundamental to their New Zealand operations for some time. Collectively the plants operating in this catchment are referred to as the Poutini Project. Recent and late Pleistocene gravels derived from the erosion of the Alpine Schists running parallel to the Alpine Fault located on the Pacific/Australian Plant boundary are thought to be the sources of the alluvial gold in the Arahura and adjacent catchments. These gravels have been extensively mined for the past 130 years yielding some six million ounces over this period. Production from the Poutini Project started in 1989 and stood at approximately 35 000 oz for the 1995 - 1996 year. This production was split among three plants each working different areas of the deposit. Recovery techniques from each of the plants are fundamentally the same. Gravels are fed to a floating treatment plant where, following screening, the gold is recovered using jig plants and knudsen bowls. Overburden to wash stripping ratios vary between zero and seven to one with plants treating between 80 and 250 cubic metres per hour. Restoration of the land following mining is undertaken progressively. All land in the Poutini Project area mined to date has been restored to a standard suitable for dairy farming purposes. The Poutini Project is a cooperative venture between the Maori landowners and DML Resources Ltd. The Arahura River has particular cultural significance to the Maori as it is the source of the much valued greenstone or pounamu a type of jade valued for jewellery and tools. The Poutini Agreement was signed in 1989 setting out the role of each party in the mining of the Arahura and adjacent lands. Current exploration and development should extend the resource to allow mining to continue on the Poutini project for an additional three to five years at current gold prices. Production within new Zealand beyond this point may be compromised by increasing difficulty in gaining access to prospective areas within New Zealand, lowered margins due to high New Zealand dollar exchange rates and the overall lowering of alluvial headgrades throughout the West Coast and Otago/Southland regions. To counter these effects DML has continued to improve on operational efficiency and performance monitoring to optimise the mining practices used. This paper detains the background to the Poutini Project, the geology, plant and equipment used together with descriptions of the current mining methods employed.

Jan 1, 1996

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By John C. Stankus

At the 13th Conference on Ground Control in Mining, a paper was presented detailing a successful test in which a new truss system was utilized, in lieu of wood cribs, for tailgate support in the Pittsburgh seam (Stankus et al., 1994). Since that time, additional tests using this same truss system in the Pittsburgh and other seams are now complete. Also, several mines are now using trusses for full panel tailgate support with no cribs. Through an extensive instrumentation program, much data and new information has been gained from these tests and the full panel usage. From this data, not only have new concepts pertaining to tailgate support been developed, but also for headgate, pillar configuration, primary and supplemental support. In this paper, an update will be presented summarizing the results of these various tailgates.

Jan 1, 1995

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

When it comes to structuring major mining contracts, the two most widely adopted formats are æmeasure and valueÆ and æcost-plusÆ. A problem with both of these formats is the difficultly of aligning the objectives of the mining company with those of the contractor to achieve mutually beneficial outcomes. An alternative contractual arrangement is for the mining company to enter into an Alliance arrangement with the contractor, linking remuneration to mine performance across a range of targets. These targets can change over time as operational requirements change. &nbsp; The aims of this paper are to: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; outline alternative types of mining contracts, as well as their strengths and pitfalls; +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; describe the philosophy behind the Alliance contract at Newmont Waihi GoldÆs Favona underground mine; and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; identify some of the keys to success and pitfalls to avoid when implementing an Alliance.

Jan 1, 2007

Worldwide minerals exploration slipped in 1992 from 1991 levels. Although industrial production figures showed the US economy emerging from recession in early 1992, it was not until February 1993 that the lagging indicator of unemployment dropped to 7%. Most other industrialized countries are still in recession. Preliminary data for 1992 showed industrial production dropping in Japan (5%), Germany (1.4%), the United Kingdom (0.5%) and France (1.4%). The slowdown in industrial production led to reduced mineral demand. This resulted in lean cash flows from mining operations, which squeezed exploration funding. Although mineral prices were steady during most of 1992, some mineral commodity prices began falling in late 1992 and early this year. Exploration 1991-1992 According to Metals Economics Group (MEG), planned 1992 exploration expenditures were down by about 5%. Geographically, the leading exploration target was the United States with 21 % of the expenditures, followed by Australia (19%), Canada (18%), Latin America (15%), South Africa (9%) and the western Pacific (7.5%). The remaining 10% was split between Europe and Africa. There were absolute increases in exploration expenditures in the United States and Latin America. Latin America showed the largest increase. The change in the Mexican mining law allowing foreign ownership of mines should result in the inflow of direct foreign investment in Mexico&apos;s mining industry.

Jan 1, 1993

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By Bill Linville

Producing oil, gas, and coal in sufficient amounts to satisfy U.S. demands for fuels, electrical power, and chemicals promises to be one of the country&apos;s major challenges during the 1970&apos;s. Adding significantly to this challenge is the urgent task of satisfying soaring fuel and power demands without destroying the natural environment or jeopardizing long-range requirements for resources. The Bureau of Mines, U.S. Department of the Interior, is engaged in a comprehensive program of research to help industry meet this challenge. This report reviews the aims of the research program and accomplishments in 1970; the first 11 sections cover coal programs, nine sect ions are then devoted to petroleum, and the concluding five sections deal with oil shale research. Figure 1 shows the nationwide distribution of Bureau of Mines energy research installations; Full addresses are given in appendix A. Many of the publications resulting from the Bureau?s energy research efforts are discussed throughout the report; others are listed in appendix B.

Jan 1, 1971

By L Barro

There is currently a worldwide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow characteristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A capillary rheometer, designed to handle settling suspension, has been used for determining rheological properties. Brown coal of 0.0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦C - 319¦C. Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physicochemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage. Apparent viscosity increased sharply with increase in solids concentration and suspensions at higher concentration behaved as non Newtonian liquids. Viscosity decreased with increase in temperature; rate of decrease slowed down with increase in temperature.

Jan 1, 1980

By J. T. Chen, S. Winkler, M. J. Worswick, O. Orlov

This paper presents a review of research conducted at the University of Waterloo concerned with the application of aluminum alloy sheet and tube in automotive structures and body panels. The research has focussed on formability prediction and results using a range of damage-based formulations. These models include continuum-level damage approaches and, more recently, a so-called percolation damage approach intended to capture microstructural heterogeneity effects on damage development. This paper presents applications of these damage approaches to simulate formability of experiments considering stretch flange panels. The experiments consider drawbead effects associated with the bend/unbend deformation as the material flows through the drawbead. Recent work on simulating in situ X-ray tomography experiments that capture damage evolution during tensile deformation will also be reviewed.

Jan 1, 2006

By L Baumgardner, A. V. Castelli

Barite In 1987, United States mine production of barite increased 15.870, consumption (sold or used by grinding plants) increased by 6.97, and imports are estimated to have fallen by 19.57. World mine production decreased by 137, according to the US Bureau of Mines. The value of US produced barite, fob mine, decreased 1.4%, according to the Bureau. The declared value for cif US port of all imported unground barite during the first 10 months of 1987 decreased from $39.02/t ($35.40 per st) to $37.16/t ($33.71 per st), the Bureau stated. Nevada continued to be the leading US producer of&apos; barite with 637r of the total. It is followed by Georgia, Missouri, California, Tennessee, and Montana. The Bureau of Mines estimates 657 of the US mine production was used as a weighting agent in drilling fluids. The remaining 35°/r was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector continued to increase. Of the total consumption (used by grinding plants and chemical manufacturers), it is estimated that 8070 was used in drilling fluids and 2017( in the non-oilfield sector - barium chemicals and fillers in paper, plastics, and glass. The tonnage consumed in the drilling fluids market increased slightly. But the average number of rotary rigs operating decreased from 964 in 1986 to 936 in 1987. This is the lowest number of operating rigs reported since 1949. The increase in consumption in this sector is due to an increase of rigs operating in the US Gulf and other higher consumption areas over 1986. Crude barite imports were estimated to be down by 19.5% in 1987. Still, they accounted for 637 of the barite consumed in the US. During the first 10 months, China continued to be the leading exporter to the US with 86.970, followed by Mexico with 10.997, and Morocco 2.107(. About 5Y of the imported ore was used in the nonoilfield sector. Ground barite imports dropped from 19.8 kt to 8.8 kt (21,800 st to 9800 st) in 1987. Of this amount, 1.4 kt (1598 st) was used in drilling muds and the remainder of the non-oilfield use. During 1987, a few more grinding plants that supplied the drilling fluid market were closed. Along the US Gulf Coast, there are 13 operating plants versus a high of 31 in 1981. Cameron Offshore reopened its grinding plant at Cameron, LA. New Riverside Ochre Co. of Cartersville, GA, purchased a jigging-washing plant in Missouri and plans to place it in operation this year on a new deposit near Cartersville, GA. Milpark purchased Hughes Drilling Fluid in 1987 and operates under Milpark. US mine production will probably stay about the same as 1987. Price increases in the 10 % range for imported ore are expected due to water freight and the weak dollar. Baker Hughes estimates the average number of operating rotary rigs at 1070. A slight increase is expected in the non-drilling fluid market (chemicals, glass, and filler). Bauxite and alumina L. Baumgardner, US Bureau of Mines Domestic bauxite production in 1987, expressed as dried equivalent, was 581 kt (640,400 st), a 14% increase over 1986. US mine production amounted to less than 170 of total world production. Virtually none of the domestic bauxite was consumed in the production of primary alumina metal. About 30% of the bauxite produced by US mines was calcined to produce 117 kt (128,970 st) for use in abrasives, catalysts, chemicals, proppants, and refractories. Most of the uncalcined bauxite was refined to specialty aluminum oxide (alumina) forms. Metallurgical grade bauxite was imported from 10 countries in 1987. Principal suppliers of the 9.8 Mt (10.8 million st) were Guinea (4270), Jamaica (3501,), Australia (127), and Brazil (57). The average value, delivered U.S. ports, cif, as reported to US Customs Service, was $29.50/t ($26.76 per st). Calcined refractory grade baux-

Jan 6, 1988

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van&apos;t Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985