Search Documents

By M. Götze, P. Eysel

Over the last years, the importance of the assessment of environmental and social aspects as well as of issues of good governance has increased significantly in mining finance. For this, international standards as well as internal guidelines of the banks and other involved institutions have been established and continuously improved. Considering these standards and regulations, the banks can influence the sustainability of mining projects - and they have done so in the past -, mainly by implementing certain provisions and covenants in the loan documentation, binding the financing to the mining company’s adherence to the agreed sustainability standards. However, there are limits to the banks’ influence due to the competitive environment with other available means of financing. Nevertheless, the experience of the last years has shown that the standards and regulations bound to the financing by the banks help to lead the mining industry towards more sustainable projects.

Jan 1, 2011

By C Bellia, A Maldonado, S Strong, H Baxter

This paper discusses the technical and cost benefits of alternative data collection techniques used to collect lithological information, obtain laboratory testing samples and perform in situ testing. A comparison between diamond coring and sonic coring techniques is made using data from a recent geotechnical investigation for a final pit slope cut-back. The impacts of the coring method on laboratory strength testing results, material character testing and, ultimately, the mass strength parameters and subsequent slope design adopted are compared. The sonic coring method was chosen out of necessity and enabled the collection of tube samples of a clay unit of interest as well as bulk samples for material character and geochemical testing. The sonic coring generated unexpected degradation of clastic units, while cohesive clay-dominated units were recovered well. The likelihood that disturbance due to the coring method would result in lower than expected triaxial strength results was recognised ahead of time, with surplus samples collected and single-stage triaxial strength testing undertaken. This testing compared favourably with historic three-stage testing, where sample degradation occurred during the later stages. Material character testing of fine-grained, clay-dominated units was comparable with historic diamond core testing, while grain size estimates for more clastic units tended to be finer than previous results. The use of sonic coring over non-cored methods enabled the collection of material texture data, geotechnical properties and a full suite of geochemical analyses. This provided a comprehensive understanding of the lithological and geotechnical character of the rock and soil mass. A high-confidence geotechnical model was developed. The end result was the development of a slope design that was more aggressive than was previously designed (5° steeper inter-ramp angle), which has proven to be appropriate to the conditions following excavation. Overall, sonic coring was a cost-effective means of obtaining additional geotechnical data for the site.CITATION:Baxter, H, Bellia, C, Maldonado, A and Strong, S, 2015. Case study assessing alternative data collection techniques and analysis methods to assist with geotechnical slope design, in Proceedings Iron Ore 2015, pp 419–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010

By Andrew Allan

[Research conducted by the Bureau of Mines hrinq the last 5 years on the uce of machines for 7!naer:rolmrl ?.eve loym~nt in pi.t,c hlng anthracite beds l~a~ provide? data ?howin? that ?:;panrt of thc roof an9 str?eg of thes? oTen - jnqs requires almst half of' the PRS? workin? time. The possibilitie~ of i!rinz a mvable,. te1.ee*co@. c tpr? 3f ?tee1 ~h-!.oltl at the face in~tetcrl of conventional wood a*ti~yorts w?r? si:~q~eteil by engineers engaqad on the~ work If ~uch a shi~l8 COLI.~,~. be ~sve~.~yad, it tnillil man that face workera w~uld be provi8ed with mulrnu.m prot?ct+on from falls of' roof and ribs mi! the en- tire ehift could he I~W? Lo ~lro,J.~:ce cocl. Fermanent tim3er coald be p'l.acnA behind the shielR independently of the 'face work as the face advanced.]

Jan 1, 1953

By G. S. Beaumont

This report presents a programme of work to demonstrate the use of a surface-based centralised computer control system for the remote monitoring and control of underground conveyors in a US coal mine. The system selected for demonstration was the 'Dynalink' Micro MINOS system which is manufactured by Hawker Siddeley Dynamics Engineering Limited. The site selected was Barnes S Tucker Lancashire No. 20 Mine located near Carrolltown, Cambria County, Pennsylvania. The system concept, operating and application software was designed and developed by the. British National Coal Board. The report describes the selection of the site, specification of the system requirements, commissioning, operation and evaluation of the system under typical US mine operating conditions. Experience with the system, based primarily on the system reliability and performance of conveyor control, was favourable. Mine management personnel felt that the system had successfully achieved its objectives and were keen to expand monitoring and control to other activities.

Jan 1, 1986

By T. Geyer

The Carbon Disclosure Project (the pre-eminent global initiative for institutional investor collaboration on climate change) groups the business risks (and opportunities) related to climate change into four categories: 1. Regulatory risks from tightening legislation (and opportunities for companies that can make the carbon market work for them), e.g. rising costs for carbon and energy-intensive processes. 2. Competitive risks & opportunities generated by a possible decline in customer demand for carbon/energy intensive products (and opportunities from a consequent rise in demand for efficient / low carbon products). 3. Reputational risks from perceived inaction on climate change (and benefits to those perceived to be ?solutions providers?). 4. Physical risks from changes to climatic patterns, e.g. asset damage from extreme weather events; project delays; water scarcity; resource risks as certain crops become no longer viable in certain areas and new supply chains become necessary; and potential human and socio-political impacts. All of these are already having repercussions for businesses in certain sectors and geographies. The understanding of specific impacts of climate change is still evolving but it is clear that climate change will have a material impact on the value of many businesses, either directly or indirectly. Many commentators and analysts consider that rising energy costs are likely to represent the most direct and immediate investment risk that climate change and the resulting regulatory responses will create for business in the near term. However, it is already possible to identify numerous examples of competitive and reputational risks and opportunities that are leading to significant value creation or destruction in business: the success of the Toyota Prius; the rush by the UK?s leading supermarket retailers to ?green? their brands; and the surging fortunes of companies involved in the manufacture of renewable energy generation equipment, are all manifestations of this trend. In addition, the potential physical impacts of climate change are also making themselves felt in certain sectors: an example is the Australian wine industry, suffering after an extreme and prolonged period of drought. THE PROJECT This paper describes a project undertaken for a multinational mining company to examine the physical risks from climate change across its international business operations. The study addressed 163 components of the business and included operating sites (mines, smelters, and refineries), key transport routes (road and rail) and port links. The inclusion of the transport networks and ports is extremely important; key transport routes (e.g. a key railway link) may often be impacted (e.g. by flooding) far more than individual sites due to their large geographic exposure and multiple potential failure points. Extreme weather events causing loss of life and major economic damage continue to be front page news. According to the World Meteorological Organization, January to July 2007 ?was marked by record weather extremes in many regions across the world.? Inevitably, the associated phenomena are starting to impact business and investments, not so much as deal breakers, but in changing the parameters of risk management and the approaches required to devise mitigation measures. EXAMPLES OF EXTREME WEATHER EVENTS No one event can be presented as directly attributable evidence of climate change, however climate change projections suggest that the frequency and severity of many extreme weather events can be expected to increase in a warming world. In August 2003, a heat wave struck Europe, with temperatures as high as 42°C (108°F). As summer temperatures in much of northern Europe rarely exceed 30°C (86°F), the area was unprepared for the disaster, and many thousands of deaths occurred. In August 2005, Hurricane Katrina caused catastrophic damage along the Gulf Coast of the United States, forcing the effective abandonment of south-eastern Louisiana (including New Orleans) for up to two months and damaging oil wells that resulted in increased oil prices. Katrina killed over 1,800 people and caused at least $75 billion in damages, making it one of the costliest natural disasters of all time. This was followed in September, by Hurricane Rita which left 119 people dead along the U.S. Gulf Coast, causing $9.4 billion in damage. In January 2006, hundreds of people were killed when Russia, Eastern Europe and Scandinavia experienced the coldest weather for decades. In summer 2007, dramatic floods in the south central region of England, UK left 350,000 people without drinking water and many without electricity. Transport infrastructure was severely disrupted; combined with floods which occurred earlier in the summer in Yorkshire (North England), the damage is estimated to total over £2 billion. ASSESSING RISKS FROM CLIMATE CHANGE To date, only a minority of companies have attempted to quantify the risks from climate change. However, investors are seeking greater disclosure of climate change related risks and opportunities and it is expected companies that can demonstrate they are prepared for climate change will attract higher market valuations. Climate Change Threats A variety of climate change threats were examined for their potential to have a potential measurable impact on the mining company?s business operations. Those considered most significant were included in the study and are shown in Table 1 (see Appendix A). Certain threats can be considered as being cyclical in nature and the future predictions may suggest a change in the frequency and severity of such events (e.g. storms/hurricanes, rainfall, drought). However other threats are associated with a gradual change over time (e.g. loss of glaciers, loss of permafrost, sea level rises). A slightly different approach is needed to address this differing nature of the threats, as described subsequently. Climatic Regions Much of the research and data associated with climate change is collected and reported on a regional basis. An example of the climate change impacts predicted for a number of climatic regions is shown in Table 2 (see Appendix A).

Jan 1, 2009

By D. Harrington, G. S. Rice, R. R. Sayers

"The Bureau of Mines in Serial No. 2606,4 issued in May, 1924, gave tentative specifications for rock-dusting to prevent coal-dust explosions in mines. Subsequently, a sectional committee of the American Engineering Standards Committee was appointed to formulate recommendations for standard practice in rock-dusting coal mines. The report of this Committee which follows was approved by the American Engineering Standards Committee, December 30, 1925. Several members of the Bureau of Mines staff served on this Sectional Committee and its recommendations are essentially in harmony with those of the Tentative Specifications in Serial No. 2606.As certain explanatory details contained in that serial are not included in the recommendations formulated by the American Engineering Standards Committee, it should be considered by coal-mine managements in conjunction with the committee's report which follows:Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions 1. Definitions of Terms Used: The term ""Mine"" shall include all underground excavations from which coal is hoisted or transported to the surface, through one or more openings.The term ""Main Haulage"" shall include all underground slopes and planes, all rock tunnels, and all entries excepting those from which rooms or chambers are turned.The term ""Entry"" shall include all underground haulageways, travellingways and airways, excepting working places as defined below:"

Mar 1, 1927

By A. Cichowicz

The objective of this work is to quantify the effect of the rock mass surrounding a stope or a tunnel on the seismic signal so that the rockburst damage on the excavation can be derived. It has been shown that the transfer function of rock mass surrounding an excavation can be modelled using a damped oscillator. The method of estimating the transfer function is extended in this paper. The parameters of a damped oscillator are estimated using inversion techniques and the transfer function is modelled as a time-varying system. The technique is tested on data acquired at three different sites in two deep gold mines. Employment of a modal model of the transfer function was suitable in two cases. Application of this technique is essential to track the time variation of the natural frequency during ground motion caused by a seismic event.

Jan 1, 1999

By Eugene Stephenson

CRITICAL analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,1 Pierce and Lewis,2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or, by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by McWilliams.4 Much of the. dissatisfaction with proration in certain fields is because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the "potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If :no difficulties ever

Jan 1, 1931

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

Peculiarities of Quartz Distribution in Zinc Flotation Products and their Influence to Mineral Processing

Sep 13, 2010

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a “stand up” or “box cut” mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of Orica’s knowledge of blast design, modelling and i-konTM electronic detonators.

Jan 1, 2003

By Arthur Notman

For the period January 1st, 1942, to January 1st, 1946, the American Bureau of Metal Statistics records the gold production of the world as 118,788,000 fine ounces. If we include 1946 at the same rate as 1945 (26,- 590,000), we arrive at a total of 145,378,000 fine ounces in the past five years . Included in these figures are estimates of Russian output at 4,000,000 ounces per annum for the five years, and 1,300,000 ounces per annum for Korea and Japan. The remaining 120,000,000 ounces represent the aggregate production from official reports of the other gold producing areas of the world, with the exception of the 1946 figures, as noted above. At $35.00 per fine ounce, this represents $5,188,230,000. According to the reports of the Federal Reserve System of the United States, on December 31st, 1941, the monetary gold reserves of the United States were $22,736,- 600,000 (at $35.00 per fine ounce) , while on October 31st, 1946 (latest available) , they had fallen to $20,402,000,000, a decline of $2,334,600,000. Adding this decline to the value of the new production for the five years, we have a total of $7,522,830,000, which has been absorbed by the rest of the world since Pearl Harbour, a rate of absorption of over $1,500,000,000 per annum. This has taken place at a rime when the advocates of purely managed currencies had convinced many people that gold performed no really essential function in the world's economy, and that we could get along perfectly well without it. It was pointed out that gold could not be eaten, it could not clothe our nakedness, it could not shelter us from storms, and, therefore, it was a non-essential, even though it could be used to settle international balances of trade. Apparently, the world as a whole still regards it as preferable to the paper promises of governments, however sound, relatively, they may appear. Actually, we have no way of measuring the true strength of this feeling, because the principal governments of the world have made it legally impossible for their citizens to own gold, except in the form of ornaments.

Jan 1, 1947

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

By Marco Olper

After two years of extensive research a new and innovative modification to the CX-EW process has been exploited. This process, called CX-EWS, avoids completely all the critical aspects of the previous process which affected the cost of the energy, of the chemicals and of The maintenance of the insoluble anodes. All these benefits reflect a saving of about 30% of The operating costs compared to the present traditional production and allow for a total operating costs of less than 6.5 cts/lb. lead (net of raw material cost). With this new technology it is allowed for the first time the treatment in the same plant facilities of both primary lead sulphide concentrate and spent batteries. The paper describes the technical and economical aspect of the new process with a feasibility study for 150,000 t/y spent battery facility throughput.

Jan 1, 1995

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which makes completely new designs of shell and tube configurations possible. Further, self-cleaning fluidized bed heat exchangers show a strong shear thinning effect in non-Newtonian liquids. All the above characteristics make the self-cleaning fluidized bed heat exchanger an ideal tool for the indirect heating of laterite nickel slurry in High-Pressure-Acid-Leach (HPAL) plants. Preliminary tests and evaluations of these heat exchangers have shown that the performance and price of these heat exchangers used for the production of nickel and cobalt from a laterite slurry, cannot be matched by existing conventional heat exchange systems. This article explains the principle, design, lay-out and enormous advantages of the self-cleaning fluidized bed heat exchange technology in a plant suitable for an annual production of approx. 45,000 ton nickel and 4,500 ton cobalt from laterite slurry through high pressure'acid leaching.

Jan 1, 2002

By John Lemke

Current practice for monitoring static pile load tests commonly consists of measuring load and displacement at the top of a pile. This is typically accomplished by monitoring dial gauge movements, line pressure of a hydraulic jacking system, and electronic load cells on occasion. While this testing approach provides useful information for one boundary condition (the top of the pile), a system that measures movement and/or strain along the entire length of the pile can provide additional useful data that can be used to refine pile design. Automated data acquisition systems provide the essential ingredient that can integrate these types of sophisticated instrumentation devices into a standard pile load test program in a cost effective way. This paper provides a general overview of pile testing instrumentation and describes a newly developed chain of instrumentation modules that can be embedded in a pile to gather additional testing information. The new system can measure forces and movements within the test pile synchronously with measurements at the pile top, and the direct application of this system to axial and lateral pile testing is illustrated. This is particularly relevant to the design of ACIP and drilled displacement piles since determination of the reinforcement cage length is important from the standpoint of both seismic design and foundation cost.

Jan 1, 2002