Search Documents

Jan 1, 1962

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By John M. Popovich

Disposing of coal mine waste at the surface has been and continues to be a problem which has yet to be resolved within the coal mining industry. A possible solution to this problem is to return the refuse back into the operating underground mine generating the waste material. It is believed that the approach described will provide an inexpensive and pratical solution to the problem. The designed system is installed and operable at the Millers Cove Energy Company, Inc. property in Lee County, Virginia. This system limits surfact facilities to a minimum size. It incorporates state-of-the-art hydraulic transport and backfilling technology and equipment to systematically backfill areas within the active mine. It maximized the benefits of reducing treatment of coal wasts while it minimizes environmental impacts on groundwater. The system approaches the problem in a manner to maximize benefits and minimize risks. The cost of returning coal waste back underground at the Millers Cove site is estimated at $0.67 per ton of marketable coal (1982 dollars), which is slightly higher than their surface disposal cost of $0.61 per ton of marketable mat (1982 dollars). The underground disposal costs do not include cost savings that should be realized within the preparation plant and treatment facilities at the surface. Preliminary tests of the system were conducted at the surface; funding restrictions prevented an in-mine trial. Efforts should continue to demonstrate the feasibility of solving the problem of refuse disposal. The installed system and plant at Millers Cove should provide the opportunity to test an underground disposal operation. This report contains guidelines to pursue this opportunity.

Jan 1, 1986

By Peter O. Wilkinson

Ascot Racecourse in the UK is a major international venue for horseracing. The racecourse is being redeveloped to provide entirely new public facilities. The development includes the construction of a new grandstand. A site investigation was earned out comprising mainly cone penetration testing. The site is underlain by the Bagshot Formation, comprising predominately cohesionless deposits of medium dense becoming dense, silty fine to medium sand, containing occasional layers of clay. Shallow foundations would present uncertainty regarding total and differential movement; hence a piled foundation solution was chosen using a continuous flight auger (CFA) piling system. The possibility that piles may found either directly on or within the influence of cohesive material suggested uncertainty regarding toe resistance. In order to measure shaft friction, an instrumented preliminary test pile was undertaken. The results were compared to published correlations of cone and shaft resistance. This approach resulted in a net saving in terms of pile length which resulted in optimum value engineering and hence a cost saving to the client.

Jan 1, 2006

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems include: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of environmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental difficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 9, 1980

By Clifford B. Farris

Introduction Shale Mining Problems The mining problems an oil shale operator will face are largely determined by the process. Candidate oil recovery processes are surface (above ground processing of mined oil shale), modified in situ (underground with some shale removed), and true in situ (completely underground with no shale removed). The shale removed for modified in situ (MIS) is generally processed by surface techniques. The mining problems are different for each category. Fig. 1 depicts the diversity of western shale deposits. Mining for surface operations will employ underground mining techniques in common use but the scale will be larger. A typical oil shale operation is expected to require 75,000 to 250,000 st (68 000 to 226 800 tons) a stream day of crushed oil shale. This is above the upper limit of current mining operations. Major problems in¬clude: (1) lack of good engineering design properties for oil shale, especially when interbedded with saline minerals at depths below 1,000 ft (305 m); (2) presence of water, hydrogen sulfide, and methane in some areas; (3) necessity for mine disposal of as much retorted oil shale waste as possible; and (4) control of en¬vironmental impacts of mining. Portions of the oil shale deposits in Colorado, Wyoming, and Utah and significant portions of the Devonian shales in the eastern U.S. are adapted to surface mining. No major technological problems are apparent outside overburden thicknesses up to 1,000 ft in the West. However, numerous political and environmental dif¬ficulties have arisen. One major oil shale developer cancelled a planned surface mining operation and currently is pursuing a modified in-situ plan. The eastern shales are closer to the surface than the western, but suffer from many of the same environmental and political problems. Modified in-situ operations face much more severe mining problems than surface efforts. Because the mined stope (called an in-situ "retort" by processors) acts as a retorting process vessel subject to gas flow, combustion, and temperatures between 1,500° and 2,000°F, mining is under highly restrictive limitations. This processing method involves removing between 20 and 40% of the shale deposit and then blasting the roof and walls into the mined space, where the oil is recovered by retorting. Major problems are: (1) swell factor severely limited; (2) need for consistent size distribution of blasted shale; (3) even filling of stope (in-situ retort) by blasted shale with consistent permeability throughout; (4) scaleup of blasting techniques, after optimization; (5) protection of retort pillars and roof during and after retorting; (6) prevention of groundwater percolation; (7)use of ANFO explosive in wet holes; (8) disposing of surface-retorted shale waste in stope; and (9) restoration of site. True in-situ operations are less well developed than surface or MIS processes. No actual mining is done, as the true in-situ processes generate permeability in the highly

Jan 1, 1980

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Geir Martin Haarberg

Modern electrolysis technologies can provide possibilities for developing sustainable processes in terms of energy and environment. Laboratory experiments were carried out to study electrodeposition of iron from molten salts and aqueous solutions using an inert oxygen evolving anode to eliminate the emissions of CO2. The possibilities of molten salt electrorefining of metallurgical grade silicon to produce solar grade silicon were also investigated. Electrochemical techniques were used to study the electrochemical behaviour of dissolved iron, silicon, and titanium species. Bulk electrolysis was carried out to deposit pure iron, silicon, and titanium. The quality of the deposits was studied by SEM/EDS and XRD analyses. Calculations based on laboratory studies indicate that great improvements in terms of reduced energy consum

Jan 1, 2010

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By L. Moyd, P. Moyd

The first commercially available portable gamma ray-neutron beryllium detector, the Rerylometer, was developed by the same group that developed the first practical portable scintillation counter, the Scintillo-meter. This group includes Professor George Brownell, of the Geology Department of the University of Manitoba in winnipeg, and his associates, K. I. Roulston, R. w. Pringle, and R. L. Funt, of the Physics and Engineering Departments of the University of Manitoba. A prototype model was tested in the field by Dr. Brownell during the summer of 1958. Commercial production was undertaken shortly thereafter by Nuclear Enterprises Ltd., of Winnipeg, and a license for manufacture and distribution in the U.S. was granted to Isotopes Specialties Co., of Burbank, California, a division of Nuclear Corporation of America. Early in 1959, we were retained by the 'Mining Division of Minerva Oil Co. to Legin a search throughout North America for minable deposits of beryllium, and to train members of their permanent staff to continue the program. The project included literature sur-veys, interviews with members of various federal, state, and provincial agencies, scanning of our own collection of suites of specimens from various mineral occurrences, and the examination of deposits in the field. The value of a beryllium detector to this program was obvious and arrangements were made to procure one as soon as possible, which resulted in our obtaining and using the first instrument that was produced commercially in the U. S. In addition to the commercially available Berylometer, Mr. William Vaughan and his associates, of the U. S. Geological Survey Geophysics Division, in Denver, have developed and tested several experimental instruments based on the same principles. DETECTOR Principles The detection of beryllium is based on the fact that "hard" gamma rays (1.6 MEV and geater), such as those produced by Antimony convert ordinary beryllium (Be9) to Be8 , with the release of a neutron. The neutrons are counted by a scintillator designed to favor neutron responses while suppressing those of gamma rays. 'The instrument is completely selective for beryllium. No other element can interfere. Instrunlentation The Rerylometer itself, which is cylindrical, is about 8 inches in diameter, 13 inches high, and weighs about 11 pounds. (Figs. 1, 2). The principal components include: 1. A disc of wax to moderate (or "thermalize") neutrons. 2. A boron-enriched polyester-zinc-sulphide fluorescent screen. This material produces strong flashes when struck by thermalized neutrons but only weak flashes from gamma rays. 3. A photomultiplier tube. 4. An electronic circuit, complete with one srnall 71/2-volt dry battery. The photomultiplier tube and electronic circuit convert neutron flashes to electrical impulses, but gamma ray effects are almost

Jan 1, 1961

Physical/Chemical Treatment of Mercury-Contaminated Wastes from Former Chlorine-Alkali Electrolysis Plants - Application of Flotation Technologies in Soil Washing Plants

Sep 13, 2010

By Steven W. Schmauch

A mineral survey by the U.S. Bureau of Mines and U.S. Geological Survey indicate the Blanco Mountain RARE II area has low potential. Lode deposits consist of small, mineralized quartz or quartz-gossan veins. The veins are sparse and widely separated and lead, silver and gold content is restricted in amount and concentration. No gold or other potentially economic minerals were found in a placer deposit. There is no evidence of industrial mineral, geothermal, or energy resource potential in the study area. INTRODUCTION A mineral resource survey of the Blanco Mountain RARE II area (No. 5059), Inyo and Mono Counties, California was conducted in July 1981. This report summarizes the results and interpretations of the Bureau of Mines investigation.

Jan 1, 1982