Search Documents

By Oliver C. Fursman

The Bureau of Mines undertook this investigation in order to determine the feasibility of producing commercially acceptable alumina and iron by application of the Pedersen process to high-silica, high-titania, ferruginous bauxites of the Pacific Northwest. Calcium aluminate slags were produced by smelting bauxite with coke and lime in an electric-arc furnace. Over 90 percent of the total alumina can be extracted by sodium carbonate solution from slags of properly controlled ternary-phase composition (CaO-Al203-SiO2) that are cooled slowly enough to permit adequate crystallization of the 2CaO-SiO2 and the calcium aluminate compounds. Most of the iron charged was recovered in the regulus; the slag contained about 2 percent iron (as iron oxide), regardless of smelting time.

Jan 1, 1968

By Fredrick L. Johnson

The Jerry Peak, Jerry Peak West, and Boulder Creep: Wilderness Study Areas contain no identified mineral resources. Two workings, a 20-ft-long adit and a pit, were found in Paleozoic, brecciated, limonitic jasperoid in the east part of the Jerry Peak Wilderness Study Area (WSA), but no significant metallic mineral values were noted. Lenses and pods of quartz containing copper minerals occur in Paleozoic sedimentary rocks 1/2 mi north of the Jerry Peak West WSA. Similar rocks crop out along Pine Creep: in that study area but no copper-bearing quartz lenses were found.

Jan 1, 1984

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

Minerals contribute to the U.S. gross domestic prod-uct (GDP) at several levels?mining, processing and manufacturing finished products. In 2008, the estimated growth rate for the real GDP of the United States was 1.1 percent and the nominal GDP was about $14.3 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. For instance, continued declines in the U.S. housing market during 2008 were reflected in further reductions in the production and consumption of cement, clays, construction sand and gravel and crushed stone (mineral commodities that are used almost exclusively in construction), and those associated with the related manufacture of goods, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard ? all used by the housing industry. The widespread effects of the slowing domestic economy became more apparent in the last three to six months of 2008 when prices for many mineral commodities declined sharply after reaching record highs earlier in the year, indicating significantly lower demand for those materials or products containing them.

Jan 1, 2009

By Floyd D. Varley, C. M. K. Boldt

Toolbox training is often described as short, informal training conducted at a worksite by technically competent persons for the benefit of a work team. The key feature of toolbox training is the focus on a work team and what is important to that group in its workplace. Toolbox training conducted by peers can connect miners and establish the feeling that the hazard is a real threat to them. This feeling can bridge the gap between delivery of a safety message and behavioral changes that can prevent an accident. Toolbox training is a popular form of "maintenance" training that should not be used to teach a new skill. The 10- or 15-minute toolbox session is simply too short a time to teach or learn a new skill and test for skill development. However, the toolbox format is an excellent way to inform workers of changes in workplace rules, conditions, or hazards by bringing the discussion of change to the level of the work group and suggesting how a change will affect the way workers perform their jobs. Toolbox training should be structured to address a very specific hazard. That is, the hazard source should be identified and the effect of the hazard on the worker described. The temptation to discuss a safety subject in broad terms will result in an equally vague result. For instance, discussing "equipment guards" is inappropriate for a 15-minute training session. There simply is not enough time to cover all the hazards and their remedies. A more appropriate topic would be "placing guards on a conveyor return roller" or "hazards of cleaning a conveyor return roller." Each topic is concise enough to allow the trainer time to define a particular threat to the safety of miners and discuss ways to defend against that threat. The clearest way to a safe workplace is to identify hazards methodically and eliminate them. This cannot be done with sweeping, generalized training. Some best practices that will protect a worker from the hazard should be presented, and the hazard should be located at the specific worksite. Toolbox training is an opportunity for the work team to participate in learning and share experiences and knowledge, often through storytelling. Storytelling is an ancient form of passing along information in an entertaining way. It is entertaining because it draws the listener in with imagination and creativity. Stories told within work groups are a way for miners to exchange experiences in which they made mistakes that resulted in an accident or a near-miss and learned a valuable lesson. Thus, co-workers can learn from others without the pain or fear that accompanied the storyteller's learning path. To encourage these shared experiences, the people in the group must be comfortable with one another. Participation doesn't stop with listening to a near-miss story or informing the group of an unsafe work practice. Participation by sharing experiences, knowledge, and skills should lead toward action in changing the unsafe tool, practice, or machine (Wallerstein, 1992). This power to change is called empowerment. Empowered workers use toolbox training sessions to discuss a problem; direct their own knowledge, experience, and talents in the context of their work environment to solve the problem; and put into practice what they have learned by sharing (Baker, 1992). A worker is much more likely to implement changes they have contributed to creating than changes forced upon them. Toolbox training functions best when the group size is small (under 20) and composed of workers with similar job functions. While combining all workers on a shift or multiple shifts may be convenient, the level of participation will drop dramatically as group size increases and participants are less connected. Similarly, when the work group participants are from different job functions, keeping the materials relevant to the individual becomes more difficult. The role of management in the toolbox training system is to communicate among various groups so that all groups at a mine site are hearing the same message. In very small operations, combining work groups can be productive if the trainer can promote open discussions and lead the group to solutions that address the needs of all and not let one group or individual dominate the discussion. WHY USE NARRATIVE METHODS An effective communications tool is to use stories as a means of describing a hazard and its consequences. Historically, using stories to transfer knowledge between individuals of the same and different generations is well established. All good stories share the same elements required to communicate safety principles. Stories require a setting (the part of the workplace), a plot (the circumstances that lead to a hazard), the solution (best practices), the lesson (what can happen), and the result (what will be done to prevent the hazard) (Dennehy, 1999).

Jan 1, 2002

By Kristen Dunlap

There are several thousand remote stream crossing structures in the Tongass National Forest in need of removal. In 2007 thirty-three collapsing log bridges, log culverts, and metal culverts no longer in use were removed with explosives. Species of salmon, trout, char, and sculpin are present in the project area. Blasting overpressures may injure or kill fish in streams and ground vibrations can damage salmonid embryos in streambeds. Regulatory agencies offer guidelines with limits for blasting induced overpressures and vibrations. However, there has been no quantification of blast overpressures in shallow streams. Methods used to predict lethal levels for various blasting applications have not been completely validated. This research provides guidance for analyzing ground vibrations and water overpressures during blasting activities in or around fish streams.

Jan 1, 2009

A production drill rig at a site in Sweden was equipped with a monitoring system to estimate production statistics. Drill running times, drill hole depths, penetration rate, rotation speed, thrust, air percussive pressure and torque pressure were recorded for every 10 mm of hole length for a period of 5 months. Operational activities (rock penetration, tube handling, moving and set-up time) accounted for almost 62% of the time consumed, the remaining 38% being different types of stoppage. Drilling itself, as opposed to handling, took less than 24% of the total time. The results give an indication of how the overall drilling capacity can be increased and which activity should be emphasised. The impacts of automation, new developments and reorganisation on production can also be predicted. Average production was found to be around 100 m/day, but varied between 50 and 160 m/d. The company's specification for the drill rig, before purchase, was that an average production rate of 130 m/d be attained over two consecutive months of drilling - a rate which monitoring shows will not be achieved

Jun 19, 1905

By J. McCoy

Charged sprays and fog have been evaluated for reducing respirable dust concen¬trations. Charged spray technology was reviewed for effectiveness, equipment and theoretical considerations. A mathematical model was developed for predicting dust reduction effects. Laboratory tests were made showing charged spray is considerably more effective at reducing dust on a unit water basis than hydraulic spray. Positive and negative sprays are equally effective. Combined polarity sprays are considerably less effective than either polarity alone. Little difference in effectiveness by dust type was observed. The charged cloud can present a spark hazard in explosive atmospheres. Due to this spark hazard from the charged droplet cloud this technique must not be used in gassy mines. Predictions were made for field test conditions but confirmation was impossible due to particles resulting from dissolved solides in the spray water. Dissolved or suspended solids in atomizing sprays can result in an increase of the respirable dust burden. Charged sprays are an available dust control technique best suited to applications where water usage must be limited and long contact time between spray and dust is possible.

Jan 1, 1983

By I Lamb

Past experience of ground settlement and groundwater monitoring for tunnelling projects in Melbourne has provided an appreciation of the value and importance to owners of establishing a broad baseline monitoring program of the ground surface movements and groundwater movements well in advance of the commencement of any excavation and tunnelling activities. For the Northern Sewerage Project (NSP) tunnels in the northern suburbs of Melbourne, a baseline monitoring network of ground settlement points and groundwater wells was established in early 2006, 18 months prior to the commencement of project construction, and has continued throughout the tunnelling and project construction activities. This baseline monitoring network provides insights into the superposition and interpretation of both tunnelling and non-tunnelling effects, such as seasonal effects, which result in ground settlement.In the case of the NSP the baseline monitoring and construction phase excavations coincided with several years of drought. The reduced rainfall developed overall downward settlement trends project wide that could easily be mistaken at the local site level to be construction effects if the baseline monitoring was not available to show otherwise. There are lessons to be learned from the NSP experience for tunnel projects where there are variable surface soil types and where project-specific settlement criteria are to be established for the protection of property prior to construction.This paper presents examples of the baseline monitoring, how the tunnelling-specific settlement was identified and determined, and what this means in terms of how settlement criteria should be established and set for project consenting and in the construction contract documents.

Mar 8, 2011

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

Delivered at the University of Sydney, on June 4th, 1954.THE TORCH WE HOLDLast year Our Institute celebrated its Diamond Jubilee, coincident with the holding of the Fifth Empire Mining and Metallurigcal Congress in Australia and New Zealand. We can be proud of our growth over the 61 years since the inaugural meeting in Adelaide in April, 1893, which followed suggestions from a provisional committee of mining men, formed in 1892 in Broken Hill.We can also be proud of our technical achievements in the fields of economic geology, mining and metallurgy.Should we be content with the growth of our mining and metallurgical industries over these years? My answer is in the negative. The discovery of new mineral deposits is essential for the continuance and development of the industries we represent.Let me review the background and trends of our industry in an attempt to emphasise the changing factors influencing the search for minerals and their exploitation.Australia was blessed with the discovery of coal in New South Wales in 1796; copper in South Australia at Kapunda, Burra, Wallaroo and Moonta in the eighteen-forties; gold in Victoria and Eastern Australia in the 'fifties; tin at Mount Bischoff, Tasmania, and gold at Charters Towers, Queensland, in the 'seventies; lead-silver at Broken Hill, New South Wales; gold and copper at Mount Morgan, Queensland, and copper at Mount Lyell, Tasmania, in the 'eighties; and gold at Kalgoorlie, Western Australia, and zinc-lead atRosebery, Tasmania, in the 'nineties. As well, the iron ore deposits of the Middleback Ranges, South Australia, and Yampi Sound, Western Australia, were known before...

Jan 1, 1954

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME 'is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959

By E. T. Turkdogan

Jan 1, 1962

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009