Search Documents

By N. Mulaudzi, S. Archer

"Direct cobalt electrowinning was developed to produce unrefined cobalt metal as an alternative to producing a mixed hydroxide product (MHP), which is the common cobalt intermediate product in African Copperbelt operations. MHP is preferred due to the high cost of producing high-grade cobalt cathode. Direct cobalt electrowinning test work results have shown that the purity of the unrefined cobalt metal produced from a low-grade copper solvent-extraction raffinate stream was ~97% (w/w), which is significantly higher than the MHP purity (up to 45% (w/w) Co). The current study investigates whether direct cobalt electrowinning would increase the profitability of African Copperbelt copper–cobalt oxide operations, when compared with the MHP flowsheet. An order-of-magnitude economic evaluation was conducted using dynamic differential discounted cash flow models on a “bare-bones” basis, using a 10% discount rate. Three variables were evaluated, namely; reagent utilisation extents, precipitation extents and filter-press wash efficiency. Multivariable risk analysis was also conducted using the Monte Carlo simulation technique to understand the impact of key project drivers. The financial study results indicated that a direct cobalt electrowinning flowsheet could potentially result in a higher mean net present value (NPV) compared with the MHP flowsheet. Cobalt recovery was found to have the most significant impact on the NPV. In addition to increased profitability of African Copperbelt operations, direct cobalt electrowinning has the potential to reduce the environmental footprint of operations as well as addressing the Democratic Republic of Congo government’s drive towards export of higher value metal products instead of low-grade intermediates."

Jan 1, 2015

By H. L. Bibbs, H. D. Snedden

"INTRODUCTION The use of beryllium and its alloys has increased rapidly during the last decade. Further expansion of its use is limited; in part, by lack of adequately developed ore reserves. The principal commercial beryllium mineral is beryl, which is found chiefly in pegmatites and produced for market as a byproduct of the mica and feldspar industries. The coarse beryl is mined selectively, sobbed and sorted by hand, and then sold without further beneficiation. The known reserves of coarse beryl are small. No method has been available for concentrating small disseminated beryl crystals, so ores of this type have not been mined or have been left on waste dumps. Disseminated ore in low-grade unmined areas and waste dumps on developed properties is a potential source of beryl, provided a method is developed for its beneficiation.Published literature on the concentration of beryl is lacking in detail or deals chiefly with tests on artificial mixtures of pure minerals, and procedures as given were not applicable to the beryl ores tested at the Salt Lake Station. The testing procedures described in this report are independent developments. By employing these procedures, beryl was satisfactorily con¬centrated from several run-of-mine and dump ores, although these ores wore low in grade and part of the contained beryl was finely crystalline and disseminated.Beryl, quartz, and feldspar, when ground to flotation sizes, are so alike in color and general appearance that they cannot he distinguished by visual observation. The progress of the work depended on rapid determination of the grade of test products by means of the petrographic microscope. Small samples of concentrates and tailings were often cut after each addition of reagents, dried, and examined under the microscope."

May 1, 1947

By G. Denton, P. den Hoed, A. Luckos

The potential application of fluidized beds in several sectors of the ferroalloy industry is promising. They can be used in the direct reduction of iron ores to produce a feed for steelmaking, in the reduction of manganese dioxide to produce a lesser oxide for feeding to smelters, in the preheating of chromite for the production of ferrochrome, and in the calcining and pre-reduction of nickel laterites for the production of ferronickel. This paper discusses the potential of fluidized beds in theses processes and highlights the advantages of the technology over other technologies, such as rotary kilns. Two primary advantages?(1) that fluidized beds can treat fine materials and (2) that fluidized beds can be integrated with smelters in a way that allows for more efficient use of energy?may well see the technology gain prominence as more deposits of lower grade are mined and industries strive to use their resources more efficiently. In discussing the potential of the technology in the ferroalloy industry, this paper focuses on the application of fluidized beds in the smelting of chromite, nickel laterites, and manganese ores. Central to the successful operation of this technology is a knowledge of how particle properties influence the behaviour and design of fluidized beds.

Jan 1, 2007

By H. F. Niemand, C. J. Postma, P. L. Crouse

"SynopsisThe separation of zirconium and hafnium is essential in the nuclear industry, since zirconium alloys for this application require hafnium concentrations of less than 100 ppm. The separation is, however, very difficult due to the numerous similarities in the chemical and physical properties of these two elements.Traditional methods for separation of zirconium and hafnium rely predominantly on wet chemical techniques, e.g. solvent extraction. In contrast to the traditional aqueous chloride systems, the AMI zirconium metal process developed by Necsa focuses on dry fluoride-based processes. Dry processes have the advantage of producing much less hazardous chemical waste.In the proposed AMI process, separation is effected by selective sublimation of the two tetrafluorides in an inert atmosphere under controlled conditions, and subsequent selective desublimation. Estimates are made for the sublimation rates of the two tetrafluorides based on the equilibrium vapour pressures. A sublimation model, based on the sublimation rates, was developed to determine if the concept of separation by sublimation and subsequent desublimation is theoretically possible.IntroductionZirconium requires several purification steps to conform to nuclear-grade specifications. Little information is available on the sublimation separation of Zr and Hf compounds, especially in the fluoride form, the majority of which deals with sublimation under vacuum conditions. On the industrial scale, only vacuum sublimation of ZrF4 has been reported. No records were found for the sublimation of ZrF4 in an inert atmosphere. Information on the sublimation rate of ZrF4 or HfF4 in an inert atmosphere is also limited. The rate is assumed to be dependent on several factors, of which temperature, area, and composition are considered the most important."

Jan 1, 2015

By B Watson

The ConSep ACACIA Reactor is a device, which utilises a high intensity cyanidation process to achieve very high, usually near total, recovery of gold from gravity concentrates. The process utilises a fluidised bed and a chemical oxidant to enhance the gold dissolution kinetics to the point where the bulk of the dissolution occurs in a few hours. For convenience and security, most plants operate a 24-hour turn around. The product from the process is in the form of cathode gold ready for smelting by traditional means. The ConSep ACACIA Reactor performs a two-fold role. Firstly it increases gravity gold production, leading to a decreased CIP feed grade. Secondly, it removes slow leaching components from the plant leaching circuit. This two fold benefit leads to the following efficiencies: enhancement of the dissolution kinetics; enhancement of the adsorption kinetics; reduction of the gold load reporting to the carbon; a significant reduction of the ægold in circuitÆ lockup; and removal of slow leaching entities which can also result in a lowering of the required cyanide concentrations in the leaching circuit and a subsequent reduction in overall cyanide consumption. The above benefits are discussed in this paper, with a particular focus on the ConSep ACACIA ReactorÆs role in removing slow leaching components, with data generated over a 21-month period. Improvement in overall plant recovery via removal of slow leaching gold species is achieved in two ways. Firstly, some of the slow leaching entities, successfully leached under intensive cyanidation, are not always fully leached under plant conditions. This results in a lowering of the solid tailing. Secondly, the faster leaching kinetics achieved in the plant as a result of the removal of slow leaching entities results in faster and more complete adsorption of the dissolved gold onto activated carbon. This results in a lowering of the solution tailings. The construction and operation of the ConSep ACACIA Reactor is simple. Apart from the reactor body, which is a proprietary design, all components of the system are æoff the shelfÆ or specific to the siteÆs requirements. In operation of the fully automated version, a PLC controls a series of valves and pumps but except for a daily changeover process the only operating component for the bulk of the time is a relatively small solution pump. The process can be totally automated giving the security of a æhands freeÆ concentrate handling process up to the point where the product is presented as cathode gold. The ConSep ACACIA Reactor was developed by Anglogold Australia (formerly Acacia Resources) for Union ReefÆs Gold Plant and has been in production since February 1999. It has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, as of June 2003 there are eighteen full installations of the processing plant installed at mines owned and/or managed by Anglogold, Newmont, Placer Dome, Independence (formerly Lonrho), Sons of Gwalia and Harmony.

Jan 1, 2003

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By S C. Dominy

This contribution examines the effect of feedstock sampling before the sorting stage of polyethylene terephtalate (PET) bottle recycling. Batches of waste PET bottles may contain non-PET bottles which need to be removed by sorting. Any residual presence of PVC is detrimental for the quality of products manufactured from recycled PET. The maximum tolerated concentration of PVC in cleaned PET is extremely low, which places high demands on the recovery of PVC achieved by sorting. To be confident of attaining the desired PET quality after sorting, acceptance sampling of truckloads of PET bottles may take place prior to sorting. It is shown that accounting for sampling uncertainty requires that the sorting process achieves a consistently high recovery of PVC bottles.CITATION:Glass, H J and Dominy, S C, 2017. Plastics recycling and sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 129–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

By R. H. Colquhoun

"INTRODUCTION The Holt-McDermott Mine is wholly-owned gold mining operation of American Barrick Resources Corp. that begun operations in June 1988.The property is located 0.5 km. south of Highway 101 East in the Harker-Holloway Townships of Northeastern Ontario, 7 miles south of Lake Abitibi and 15 miles west of the Quebec-Ontario border.Employees of the operation travel daily from various communities in the area, predominantly from Kirkland Lake, Ont., which is located 65 km. to the southwest.The significance of the operation is that it is the first full scale operation associated to the Oestor-Porcupine Fault to go into full production in recent history as well as the first Carbon-in-Leach (CIL) operation in the province owing to the natural occurring carbonaceous ores that are associated to the ore body and the geological fault systems.GEOLOGYThe Holt-McDermott deposit is located in the Abitibi Greenstone Belt, a short distance west of the Ontario-Quebec border. Ore grade material follows the footwall contact of a fault zone known locally as the McKenna Fault, which is thought to be a splay off of the Oestor-Porcupine Fault, itself a major feature in the Abitibi belt.The McKenna Fault strikes approximately east-west (as does the Oestor-Porcupine) and dips to the south at sixty-five to seventy degrees. The fault lies within a package of mafic volcanic rocks (basalts). These rocks have been strongly altered and mineralized adjacent to the McKenna Fault, and the resulting lens-like ore bodies constitute the mining targets."

Jan 1, 1989

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By H. Robert Ensminger

The Belizean economy registered a modest real growth of 1.3% during 1981. The gross domestic product (GDP), based on current prim was $121 million' with an inflation-rate of 10%. The country received $19 million in economic aid during 1981. In early 1981, Belize'e four commercial banks raised the interest on deposits to 15% in an effort to curb capital outflow. During 1981, the financial situation deteriorated somewhat, particularly the balance of payments. For the year the total value of imports exceeded exports by almost $38 million, while the Government continued to maintain a fairly free trade policy. Import duties and term averaged about 8% on essential item and 40% on nonessential ones.

Jan 1, 1983

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1974 figures because adequate world information was not available beyond that date. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production, consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 2012

By Y. M. Chen, H. L. Zhang, W. U. Bing, C. Q. Zhou

Multiphase flow in the widely used Vanyukov furnace was numerically studied. An unsteady three-dimensional and three-phase flow model was firstly built using the computational fluid dynamics (CFD) software ANSYS FLUENT®, and then solved with the volume of fluid (VOF) and k - ??model. The results showed that the proposed model could be used to predict the multiphase movement, the slag/air fluctuation, the vortex formation, and effects of structural and operational parameters. By fast Fourier transform (FFT), the dominant frequency of density with time signal was calculated as 0.29 Hz. The analysis of different injection flow rates of enriched air indicated that this variable has a major effect on the mean slag velocity. The peak mean velocity increased from 2.17 to 4.99 m/s while the flow rate of enriched air varied from 70 to 160 m/s. The proposed model provides a method to optimize the furnace structure and operating conditions for the best furnace performance and lowest energy consumption.

Jan 1, 2015

By Eric Schraml

Wardrop Engineering and the Placer Dome?s Campbell Mine Design Team utilized leading edge directional raise boring techniques and an innovative, remote controlled application of steel fibre reinforced shotcrete ground support to achieve improved mine ventilation and a superior, safety focused secondary emergency egress. While more standardized methods may have provided a sufficient solution to either the requirement for a ventilation raise or for a traditional escape ladder way, innovative methodology ensured both objectives were met with a single, enhanced solution. Placer Dome committed to provide a solution that minimized energy consumption, optimized air delivery and facilitated an escape way focused on minimizing the negative physiological aspects associated with mine evacuation. The project was successful in providing a new airway, returning 47 m3/s (100,000 cfm) from the 39 Level to 30 Level, minimizing risk to the raise equipping crew and providing a fully equipped escape hoist. The resulting secure escape environment provided an efficient means of evacuating personnel working at depth without necessitating a potentially dangerous exhausting climb to surface. The project has substantiated, that optimized safety focused design can be achieved without jeopardizing project economics.

May 1, 2002

By L. B. Clarke

The optimal maintenance and control of the air flow and pressure distribution in a mine network are achieved by the correct positioning of the mine fans and regulators within the mine ventilation circuit. The principal considerations are the location of the main and underground fans or regulators and the attendant control of mine leakage. Air flow control is achieved by either passive or active regulation. Passive regulation adds resistance, usually in the form of a regulating door. Active regulation adds pressure sources in the form of underground booster fans. Ventilation engineers are increasingly turning to analytical tools to assist them in the design and operation of ventilation systems. The application of computer methods, formal optimisation methods and numerical solution methods is outlined

Jul 1, 1996

By Charles D. Wood

"Selected Topics,? in reviewing the control of emissions from diesel engine powered equipment used in underground mining, explores these fields of interest: hydrogen as fuel; lubricating oil as a source of particulates; applicability of stationary source scrubbers; worldwide diesel exhaust scrubbers; instrumentation technology for measurement of N02; control of emissions through application of sensors and microprocessors; use of fuel additives; technology transfer of marine diesel practice; technology required to use 4-stroke, aftercooled, turbocharged, direct injection engines; oxidation and reduction catalysts for diesel engine exhausts. "Selected Topics? makes recommendations for research and provides a bibliography and lists of references.

Jan 1, 1979

By G. Papachristodoulou, O. Trass

"Performance data for both wet and dry grinding of materials have been obtained in this novel, planetary ring-roller mill over wide ranges or operating conditions. The Szego mill consists of a stationary cylindrical shell inside which grooved, radially mobile rollers rotate, driven by a central shaft. The mill has several internal design variables such as number, diameter and length of rollers as well as size, shape and pitch oi helical grooves. It is compact, has a high specific capacity, modest power consumption, and can grind many materials down to ultrafine powders. Illustrative data on product fineness and mill power consumption are given along with results from studies on grinding kinetics.INTRODUCTIONThe extensive use and importance of grinding as a unit operation, coupled with the rather low energy efficiency of conventional equipment provide a challenging incentive to investigate novel methods of comminution. Yet, most current development work is taking place in mill performance modelling and optimization, or with various detailed improvements rather than in the field of new equipment development.This paper is a report on the development of a ring-roller mill invented by the late L.L. Szego which embodies several novel concepts. The mill has a broad range of applications, may be operated wet or dry, and can grind materials down to ultrafine sizes with modest energy consumption. It has been developed by General Comminution Inc. in close cooperation with the University of Toronto."

Jan 1, 1986

By Stephen L. Chryssoulis, Daniela Venter, Stamen Dimov

"Comparative surface analysis of floated and rejected free gold grains from a number of full scale benefication plants and from pilot plant testwork, has shown silver (the most common impurity in gold) and sulphur invariably in greater concentration on floated gold grains, implying that they assisted gold flotation (gold activators). Collector loading measurements on individual gold grains from concentrates of staged rougher flotation tests on a cyclone U/F product of a pyritic gold ore, revealed first progressively lower concentrations of the collector monomer on gold from each follow-up concentrate and secondly a direct proportionality between the surface concentration of silver and the collector monomer. These two observations leave no doubt that silver activates gold and that collector monomers play a significant, previously not fully recognized role in gold flotation.INTRODUCTIONGold to some degree is naturally floatable in industrial systems, which means that it can be recovered without collector addition (Marsden and House, 1992). This is due to the adsorption of hydrocarbons and deposition of sulphur, which are dependent on the metallic properties of gold, particularly its high electrical conductivity, which allows surface electrochemical reactions to occur catalytically and selectively. Cyclic voltammetry has shown that gold can be rendered hydrophobic by deposition of a surface layer of sulphur (Sº) from S2- and HS- solutions (Walker et al., 1984). Twenty monolayers of sulphur were required to produce a hydrophobic gold surface.However, no sulphide flotation plant relies solely on the natural floatability of gold for its recovery. Gold hydrophobicity is enhanced by the addition of flotation collectors such as xanthates (X), dithiophosphates (DTP), dithiophosphinates (DTPI), mercaptobenzothiolates (MBC) etc., as used in sulphide mineral flotation (Dekok, 1973: Adams et al., 1986). The mechanism invoked in enhancing the hydrophobicity of pure gold with the aforementioned four groups of collectors is similar to that of pyrite, whereby collector anions are oxidized at the gold surface to form dimers (Groot, 1987; Marsden and House, 1992; Basilio et al., 1992) As an example, xanthate ions are oxidized at the gold surface to form the neutral dimer dixanthogen (X2):"

Jan 1, 2003