Search Documents

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

The Mount Lyell Mining Field is Australia's chief productive source of copper. It is situated near Queenstown, on the western flanks of the West Coast Ranges, about 20 miles from the west coast of Tasmania (Fig. 1).The following observations on the mineral composition of the copper ores of the Mount Lyell Field are based on a...

Jan 1, 1939

By David O. DeGagné

While mine backfill plants are becoming increasingly more automated and instrumented, especially with paste fill operations, underground backfill distribution systems have hardly changed over the years. While fill properties are appropriately measured in the preparation plants, as backfill enters the mine borehole, the technology for control, data gathering and reporting is somewhat lacking. Mines typically experience problems with borehole and pipeline plugging, pipeline bursting, bulkhead failure and exposed fill sloughing. With adequate instrumentation of the backfill system it is possible to obtain a complete, continuous and detailed picture of the entire filling operation from preparation to post-pour. Good data will, over time, provide the basis for needed improvements of backfill systems and will be essential to safer, more efficient and less costly fill practices. This paper will review the areas of the filling operations where monitoring would prove critical to eliminate failures such as pipelines, bulkheads, fill exposures, stope walls, etc. The types of monitoring systems currently available will be reviewed and potential areas for development will be highlighted.

May 1, 2001

By M Bourke

Modern computers and software provide powerful tools for the geologist to construct reliable models of geological resources, and the mining engineer to produce accurate and workable mine plans. Over the years many people have developed a phobia of computers, especially for geological analysis, modelling and mine planning. This phobia is often caused by a lack of knowledge, poor training or a bad experience. The adoption however of computers for geological modelling and mine planning is now becoming mainstream. With the correct training, a good understanding of input data, and detailed knowledge of the required results, the phobia can safely be overcome to provide mining operations with increased productivity.

Jan 1, 1999

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By D Craw, J Becker

Post-metamorphic structural evolution of Otago Schist resulted in a pattern of northwest and northeast striking faults and fractures cutting the basement rocks. These faults have been reactivated several times since Mesozoic metamorphism. Gold-bearing quartz veins which have been exploited sporadically over the past 130 years are almost invariably hosted by northwest striking structures, and most exploration has been focussed on these structures. There is evidence for hydrothermal activity and mineralisation along some of the northeast striking structures, although there has been very little work done on these structures. Our study is attempting to characterise the hydrothermal processes in the northeast structures, in comparison to the northwest structures, in order to see if further detailed exploration is warranted. There is evidence for both normal and reverse senses of movement on northeast striking faults, and some of the faults have evidence for early ductile deformation overprinted by later brittle structures. Northeast striking structures host stibnite mineralisation in places, and faults are locally silicified or extensively impregnated with ankeritic carbonate. Sulphides are rare in veins, but do occur in some hydrothermally altered host rocks. Hydrothermal haematite accompanies extensive silicification along the Manuherikia fault zone near Alexandra. Anomalous gold concentrations occur in some hydrothennal zones, and in downslope sediments in some localities.

Jan 1, 1998

This paper sets out to examine the possible relationships between three factors, they are, the rate of growth of world production of minerals, the growth of Australian production and the growth of scientific and engineering knowledge.The first two are quantified, in terms of tonnes and value. The third, an abstract concept "knowledge", requires to be quantified, in terms of manpower.A mathematical model, which has general application, was derived to demonstrate certain axiomatic premises and to define, more precisely, basic concepts related to the philosophy of knowledge.Finally a summary is made of education-cum-industry issues.

Jan 1, 1981

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

By J. Durkin

The Bureau of Mines has conducted field studies in coal mines throughout the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above these mines. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10% false-alarm rate, the expected probability o detecting a miner's signal" from a depth of 1000 ft is 54% at 500 ft it is 95%. These depths exceed the actual depths of 90 and 50%, respectively, of United States coal mines. Sensitivity studies have shown that at depth of 1000 ft, the probability of detection will improve approximately 2% for each dB of increase in signal-to-noise (SNR) ratio.

By Scott Orenstein

Construction blasting has allegedly been the cause of property damage in the following situations: (1) When the detonation of the shot hurls rock and debris into the air that causes property damage upon impact; and (2) When property owners notice cracks in their walls and foundations after they experience the momentary vibrations that coincide with the detonation of the shot. The current state of the law for both these situations is firmly established. Blasting is classified as an abnormally dangerous activity, for which the blaster is held strictly liable, whether the damage is the result of flying debris or vibrations and concussions generated by the blast. It is when the alleged blasting damage is supposedly from concussions and vibrations, however, that the courts usually reach the wrong result. The typical scenario involves property owners that thoroughly investigate their property after feeling blast generated vibrations, and find cracks that they believe did not exist beforehand. Most often the truth is that the property owners have never noticed these cracks before because they have never looked that closely before. Any structure has a certain number of cracks due to a variety of causes, such as settlement overtime and temperature and humidity changes.

Jan 1, 2004

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress,

Jan 1, 1965

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources:

Jan 1, 1965

By Torben Edens

Norddeutsche Affinerie?s (NA?s) primary smelter continually increased production in the past decade. The smelter?s concentrate capacity was expanded from 500,000 in 1993 to 1,000,000 t/a dry concentrate in 2000 and the goal of the present upgrade is 1,150,000 t/a. These goals were reached without erecting new equipment in the anode area, but instead by refitting the existing plant. The life-span extension of the casting moulds was absolutely necessary to increase the casting performance from 260,000 to 450,000 t anodes per year on a single casting wheel. Different mould manufacturing processes and alloys were tested in order to find the optimal mould. In the past the moulds were cast directly, now the anode mould is milled into NA copper cakes. Accompanying measures taken were the shortening of maintenance and repair times as well as improvements in the refining furnace equipment.

Jan 1, 2005

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981

By Mohan K. Wali

This report, the first in a series of 13 reports, provides a summary of 11 major topics on which individual reports have been prepared. These major topics are: (a) Nature of coal mine spoils, topsoils, and unmined soils; (b) influence of macro- and microclimate on (c) plant production on spoils and topsoils; (d) prediction of aboveground biomass from plant cover; (c) mineral composition of plants; (f) controlled environment studies on plant growth response; (g) microbial communities (h) water chemistry and organism diversity of catchbasins; (i) vegetation and soil development on abandoned, and (j) topsoiled sites; and (k) viability and diversity of seed bank. Based on these investigations, general conclusions and some recommendations are presented.

Jan 1, 1982

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By B Vorster

Falls of Ground is one of the highest causes of incidents, accidents and fatal injuries in our mines today. These falls of ground may occur as soon as the face is exposed after blasting or after machine cutting. The falls of ground can also occur after support has been installed. There are many reasons why these falls occur before and after supporting of the face. It is therefore important to support the exposed face as soon as possible to prevent the falls of ground. It is also very important to support the face with the correct support products and to support the face as designed and required by the mining engineers. The possible reasons for falls of ground, possible support methods and the products available will be discussed in this presentation. In typical conventional narrow vein stoping operations, the use of conventional temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The author wishes to discuss the following items in this paper:- ? Introduction ? Basic face behaviour after exposure ? Controllable Parameters ? Mining Engineers support designs ? Primary and Secondary Support ? Products available for prevention of falls of ground

Jan 1, 2008

By Clive Chadbourne

Investigations of world wide coal face strata control practice, the study of theoretical calculations and detailed engineering analysis have been combined to design and select a powered roof support suitable for use in conjunction with the extraction of 4.5-m (14.7- ft) of the 7.5-m (24.6-ft) thick Warwickshire Thick Coal Seam. The interface between geotechnical criteria and engineering design has been closely considered along with the following 3 important factors: Firstly, the need to further improve strata control and operational characteristics whilst producing a wall integrated overall face design. Secondly, to enable the supports to be rapidly transported from face to face in roadways driven at the minimum size for operational requirements. Finally, to provide hydraulic power, automatic control and monitoring systems which will improve operations reduce manpower requirements and improve management information. Clear design requirements were determined in order to allow selection on a commercial basis. A method of tendering is described with the subsequent analysis and selection process. In the event oversupply of coal in the UK resulted in the order not being placed. Brief consideration has been given to supports suitable for reserves to be mined In a few year's time where there is potential for extraction well in excess of 4.5-m (1 4.74.

Jan 1, 1994

By Jean-François Dorion

La corrosivité des environnements miniers souterrains est un phénomène peu étudié au Canada. En plus de détériorer les systèmes de soutènement, la corrosion s?attaque aussi à divers installations et équipements souterrains. Cette étude, débutée en janvier 2007, est l?établissement d?une banque de données afin de caractériser les environnements miniers souterrains selon leur potentiel de corrosivité pour les systèmes de support de terrains. Pour ce faire, cinq (5) mines ont été sélectionnées afin de comparer les environnements : Laronde, Géant-Dormant, Niobec, Mouska et Doyon. À chacune des mines, trois (3) endroits ont été étudiés. Les résultats préliminaires démontrent une grande variabilité des conditions d?une mine à l?autre ainsi qu?à l?intérieur même d?une mine. La minéralogie des roches et du gisement influence la composition des eaux souterraines et la présence des sulfures joue un rôle important sur l?agressivité de l?eau et de l?air des mines de l?étude. Afin de déterminer le potentiel de corrosivité, plusieurs paramètres doivent être considérés et la mine doit être zonée selon l?agressivité des endroits.

Feb 1, 2008