Search Documents

By T. T. Chen

This mineralogical study is based on samples from typical "wet" nickel laterites of humid tropical to sub-tropical regions. An in-situ nickel laterite sample from Goro and a transported laterite sample from Plaine des Lacs, New Caledonia, are predominantly limonitic. Two-thirds of the particles in the Goro sample are <10 um in size; they consist of skeletal goethite and serpentine, as well as minor amounts of talc, gibbsite, chlorite, quartz and clay minerals. The coarser grains are mainly Cr-spinel, serpentine, gibbsite and Mn oxide. Nickel occurs mainly in goethite, serpentine and Mn oxide; cobalt occurs in goethite and Mn oxide. The Plaine des Lacs sample is finer-grained and contains more Al and CO3, but less Mg and Si than the Goro material. The sample contains more kaolinite, chlorite, siderite and feldspar, but less serpentine and gibbsite than the Goro material. Nickel is detected mainly in goethite, serpentine, Fe-Mg silicate and Fe-Mn oxide. The Indonesian ore from Sorowako, as sampled from the reduction kiln feed containing some reverts, is predominantly saprolitic, with apparent particle sizes ranging from <100 um to > 1 cm. The sample of reduction kiln feed is rich in Mg silicates, Mg-Fe silicates and goethite, and exhibits complex alteration textures. The nickel contents vary from particle to particle. Nickel is present mainly in serpentine, olivine, chlorite and amphibole, and in subordinate amounts in goethite and Mn oxide. Cobalt is detected in the Mn oxide. Keywords: Nickel Laterite; Mineralogy; Nickel Carriers; Goro, New Caledonia; Plaine des Lacs, New Caledonia; PT Inco., Sorowaki, Indonesia

Jan 1, 2004

By K. Zipf, Z. T. Bieniawski

"An extensive mixed-mode fracture toughness testing programme was conducted on coal from three coal fields. A special mixed-mode testing fixture for coal and other geologic materials was developed together with reliable specimen preparation procedures. Dynamic modulus measurements made on each of the 116 fracture toughness specimens showed that these coals exhibit certain degrees of anisotropy. The fracture toughness testing programme systematically varied the loading rate, specimen orientation and fracture loading mode. Loading rate did not significantly effect the fracture toughness over the quasi-static range tested. Orientation did have a significant effect on measured fracture toughness. In the coals tested, the divider orientation and arrester orientation had higher fracture toughness than the short transverse orientation. Data showed that one orientation could have almost twice the fracture toughness as another. The fracture toughness testing enabled certain evaluations of three mixed-mode fracture theories: maximum tangential stress, maximum energy release rate and strain energy density theory. Due to the extreme heterogeneity of the coals tested, definitive conclusions regarding the best mixed-mode fracture theory are not possible; however, data do tend to support the strain energy density theory. INTRODUCTIONThe major aim of this research is to ·develop a fundamental understanding of how fine· fragments of coal (respirable dust) are generated during a fracture process. In a related paper [l], a hypothesis was presented for the mechanism of fine fragment formation during a generic coal material/cutting tool interaction. In this hypothesis, fine fragments are created during coal material/cutting tool interactions that are best described as general mixed-mode fracture processes. Data are required on the mixed-mode fracture behaviour of coal, the physical character of the newly-created fracture surfaces and the character of the inherent flaw structure of the coal material. Accordingly, a test programme was designed that provided some information in each of these areas. The testing effort seeks to measure critical fracture toughness under mixed-mode loadings as a material parameter characterizing in part the tendency of various coals to generate undesirable quantities of fines and respirable dust."

Jan 1, 1990

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010

This paper addresses, in particular, the influence of winding depth on the selection of head ropes for Koepe winders. Because this is just one aspect of winder design that affects the operational safety of the winding system, the paper starts by considering all the issues governing the life and safety of the winding ropes. Regulations from a variety of countries are reviewed and comparisons of the legislated rope factors of safety and their variation with winding depth are made. This is followed by a discussion of the typical observed mode of in-service deterioration of Koepe head ropes. This mode of deterioration is due to fatigue and is influenced by the load range occurring in the ropes. Parameters contributing to load range are discussed and the influence of winding depth is highlighted. Lessons learned from early experience with very deep Koepe winders in South Africa are recalled. Predictions of load range as a function of depth are made, from which general rope life predictions are made for ropes selected by conventional national factor of safety requirements. This is illustrated in graphs comparing rope life as a function of depth. Typically a reducing life with depth is predicted. A rope selection strategy is advocated, which is based on achieving a constant rope life irrespective of the depth of wind. A new factor of safety (or rope design factor) equation is prepared that has the trend of increasing with depth. This proposed equation is compared with other published proposals that promote an increasing rope factor of safety with depth. It is shown that smoother winder drive controls enhance winding rope life and this improvement is quantified. The paper concludes by pointing out the consistency in predicted and observed life of winding ropes selected in accordance with legislated factor of safety approaches. It recommends the adoption of a new rope design factor equation for rope selection, to be used in conjunction with appropriate codes of practice for winding rope condition assessment and for the design, installation, operation, maintenance and testing of Koepe winders. The new rope design factor equation approaches a limiting economic depth of wind at shallower depths than the existing Koepe factor of safety approaches. However these older approaches æbuild-inÆ a reducing rope life with depth. The new rope design factor is therefore a more consistent way to select Koepe ropes and to evaluate economic trade-offs between Koepe and conventional double-drum or Blair winding systems.

Jan 1, 2005

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By H. Al-Kazzaz

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded using 1.6 mm EZ33A-T5 filler wire and a continuous wave Nd:YAG system at a power of 4 kW, surface defocusing and various welding speeds, Compared with the base metal, the fusion zone showed significant grain refinement due to high cooling rate, No grain coarsening was observed in the heat affected zone (HAZ). The porosity area percentage and total solidification crack length in the fusion zone (FZ) were reduced as the welding speed increased from 4 to 7 m/min, Fusion zone area, total penetration depth, and weld width decreased with increased welding speed, The hardness in the FZ was similar to or higher than the base metal after a natural aging of about one year, but there was a drop in the hardness of the HAZ, The HAZ width decreased with increasing the welding speed, Tensile test showed that a joint efficiency of approximately 75 ? 90 % was obtained.

Jan 1, 2005

By K. A. Natarajan, Abha Kumari

"The effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. The effect of applied potentials and electrolytic currents on the activity and growth of bacterial cells was assessed. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and biocatalysis of anodic oxidation. IntroductionIn recent years, the bioleaching of low-grade chalcopyrite ores as well as their flotation concentrates has been receiving increased attention. Use of mesophilic bacteria such as Acidithiobacillus ferrooxidans in the bioleaching of chalcopyrite does not yield desirable copper extraction rates due to its easy passivation.Bioleaching of chalcopyrite using A. ferrooxidans has been reported to be very inefficient, and use of thermophilic bacteria at higher temperatures is recommended to improve its bioleaching rates. Bioleaching under imposed applied DC potentials or currents has been shown to enhance not only bioleaching kinetics but also to confer selectivity in mineral dissolution (Abhakumari, 1996; Chirpa Selvi and Natarajan, 1998; Natarajan, 1992a, b,c). Electrochemical principles governing electrobioleaching have been earlier illustrated (Jyothi et.al, 1989). The role of applied potentials on the activity and growth of A. ferrooxidans has also been studied (Natarajan, 1992b). Also, the electrochemical aspects of bioleaching of several sulfide minerals when present alone or in binary and ternary combinations have been reported (Jyothi et al., 1989). The electroleaching of copper-nickel concentrate (Natarajan et al., 1985) and electrobioleaching of sphalerite concentrates have already been studied (Selvi et al.,1998). However, it is possible to enhance the bioleaching rate of chalcopyrite in the presence of A. ferrooxidans under galvanic conditions in the presence of nobler minerals such as pyrite (Jyothi et al.,1989). Also, dissolution of chalcopyrite can be significantly enhanced under applied potential conditions. Ali Ahmadi and his coworkers recently studied the electrochemical bioleaching of chalcopyrite concentrates using moderate thermophiles (Ahmadi et al., 2010, 2011)."

Jan 1, 2015

By A D. Campbell

The sublevel caving (SLC) mining method is becoming more widely adopted as an underground mining method as mines become deeper and target lower grade mineralisation. SLC has been successfully adopted in increasingly complex and wide-ranging conditions in the past 10–20 years, demonstrating the flexibility of the method. Various challenges encountered at SLC mines around the world have led to significant differences in operating practices, mine performance and mine productivity. Unfortunately, aspects related to productivity, operational performance and best practice are not widely published and remain with individual companies. Limited information is publicly available to compare operational performance of SLC mines in the various conditions where the mining method is now being applied. To overcome this shortcoming, a global review of SLC operations was undertaken over a three-year period as part of the Cave Mining 2040 research consortium. The purpose of the review was to document technical and operational practices, hazard management strategies and key benchmarking metrics at SLC mines around the world. A total of 21 mines spread over four continents and 17 different mining companies were included in the project. The main outcome of the project was a manual of operational and technical practices, benchmarking of key metrics and documentation of the current state-of-the-art for each aspect of SLC mining. This paper describes the main findings from the benchmark in terms of mine productivity, including mine development, production and mining costs. The implications of mine scale, depth and ground conditions on operational performance at each of the benchmarked mines is described and charts are provided comparing key productivity metrics.

Mar 29, 2023

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023

By T. F. Oliveira, E. B. Zanelato, J. Alexandre, L. J. T. Petrucci, A. R. G. Azevedo

The paper and cellulose industry is responsible for generating large amounts of solid waste, which are produced during various stages of the production process. Currently this material goes to places like landfills and other generating costs for the company. Furthermore, cement, mortar and concrete represent a significant economic and environmental cost. This study aims to determine the pozzolanic activity index in the residue studied to verify its viability in the incorporation of the same in cement. It will be used Luxan method for this determination. The data found show that the material has the possibility of being incorporated in the mortar due to its pozzolanic activity index.

Mar 1, 2017

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By Edwin B. Wilson, Charles F. Cockrell

The application of evolutionary operation is proposed for the cleaning of coal by the heavy media process. Analysis of the data given suggests some benefits that may not be immediately appreciated unless evolutionary operation is applied. For example, while it may seem obvious to increase specific gravity when the ash and sulfur content of the clean coal is lower than that allowed, evolutionary operation may show that an increase in feed rate or an increase in both feed rate and specific gravity would be a more profitable alternative. In addition, by using evolutionary operation, up-to-date knowledge of the effect of change of feed rate or specific gravity on yield and product quality is available. This information facilitates confidence about decisions made in regard to the day-to-day operation of these units. A number of other applications in the minerals industry are proposed. An application of evolutionary operation in a related field is also given where a large number of variables were required to be optimized.

Jan 1, 1969

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African coal discards derived from feed coal for thermoprocesses pose human health and environmental problems and incur high disposal costs. These issues need to be resolved. Coal fines and a coal fines/ K2CO3 blend were combusted at 700°C in a laboratory rotary kiln to produce ashes containing metakaolinite (Al2O3.2SiO2) and illite/muscovite/orthoclase amorphous materials. The blend ash and coal fines ash, containing 18% K2O and <1% K2O respectively, were leached with water and with 1 M and 8 M NaOH at 80°C for 4 hours using a solid to liquid ratio of 1:5. The 8 M NaOH leach yielded 17% sodalite (Na8Si6Al6O24(OH)2) formation through SiO32-, Al(OH)4-, and Na+ precipitation in the leached ashes. The 1 M NaOH leach yielded no sodalite. X-ray fluorescence analysis of the original ashes and leached ashes showed low Al and Si dissolution efficiencies due to the sodalite formation. Sequential NaOH leaching resulted in the highest potassium dissolution efficiency of 89% for the ashes of fines/K2CO3 blend and 59% for the fines. It may be possible to increase the ash-derived zeolite concentration by using even higher NaOH concentrations (12–20 M NaOH) during leaching. Sodalite derived from coal ash could possibly be utilized for water purification in industrial applications, or as molecule separators. The potassium-containing liquid could be used in fertilizer manufacture.

Mar 30, 2023

By C. Ntsele

Stirred milling technologies have firmly established themselves in concentrator circuits as energy-efficient alternatives to tumbling ball mills. High and continued increases in electricity costs, coupled with the ever-increasing power consumption by primary grinding circuits due to declining head grades of ore-bodies, provides a compelling case for these technologies. Additionally, the ability to successfully deploy stirred milling in coarse grinding applications extends the range of use in concentrators, thus increasing the opportunity matrix for energy optimization in a flowsheet. This paper therefore details methodologies and strategies that can be applied to evaluate the optimum stirred milling solution for different concentrator applications. These methods and strategies will focus specifically on the two major stirred mill machine types; namely, gravity-induced (VERTIMILL? grinding mill and Nippion-Eirich tower mill) and fluidized (SMD, Isamill?, Knelson-Deswik mill, etc. ). Finally, case studies from circuits across industry and laboratory tests will be used to illustrate the energy benefit from the use of stirred mills.

Jan 1, 2012

By W. W. Adams

"The present world-wide demand for increased production in all branches of essential industry involves a matter of vital concern t persons engaged in the mining industry, namely, the productive capacity of the individual mine employee. This applies particularly to coal-mining, upon which other industries so largely depend.The folded and faulted condition of the coal beds in some countries, as well as the thinness and depth of the seams, the adaptability to the beds of available mining machines and equipment are factors which cannot be overlooked in determining what increase in individual output may be looked for in any given country. This subject, while of fundamental importance, can only be referred to in a paper of this length, the primary object here being merely to present a comparative tatamant of individual output under prevailing conditions.The quantity of coal produced by a miner does not accurately indicate the miner's capacity as a workman, not only because of the natural conditions referred to above that limit his annual output, but also because of human factors which may possibly, however, be controlled, such as the demand for coal, the car supply, use of labor-saving machinery, number of days worked during the year, accidents in the mine, etc. It will, however, be an aid in answering the important question as to how and where the immediate need for coal throughout the world may best be surlier, if we examine the output of the miners in the important coal-producing countries over a period of years.Complete official information for recent years is, for several countries, jacking, particularly for France, Austria, and Prussia, but partial data from unofficial sources may be used to show the individual output of the miners in these countries."

Jul 1, 1920

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By Noan Tonini SImonassi

O atual cenário global de crescente conscientização ambiental de consumo de materiais e da busca por utilização de materiais que sejam menos agressivos aos ecossistemas. Fazem com que novos materiais oriundos de fontes naturais, de acordo com tendências e desenvolvimento tecnológico, se tornem alvo de pesquisas. Neste contexto, a utilização de fibras naturais ocupa uma posição destacada. O objetivo deste trabalho foi avaliar o comportamento de resistência de compósitos reforçados com 30% em volume de um tecido de fibra de fique e manta de curauá, com matriz de poliéster, por meio de testes de impacto Izod. Foi observado que a adição do tecido fique e da manta de curauá resultou em um aumento significativo na energia absorvida pelos compósitos, quando comparado com o material sem a adição de reforço. A observação macroscópica dos espécimes pós-impacto e a análise de fratura obtidas através de microscopia eletrônica de varredura (MEV) revelaram que a ruptura transversal através da interface dos compósitos com a matriz de poliéster é o principal mecanismo para a tenacidade destes compósitos.

Oct 30, 2017

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By Denis Shishin

The pyrometallurgical production and recycling of non-ferrous metals involves the use of complex feed stocks, having awide range of chemical compositions from sources that include mineral sulphide concentrates, high value obsolete materials and process wastes. The commercial viabilities of these operations hinge on the ability to extract value from these materials. Increasingly, modern computer-based tools are used to describe and predict process outcomes, including mass and heat balances, the partitioning of elements and phase equilibria. At the heart of these predictive tools are thermodynamic databases that describe the fundamental chemical properties of a system and all the components present. A comprehensive research program has been established to develop an accurate, self-consistent thermodynamic database describing all gas-slag-matte-metal-speiss-solid phases in the system Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Sb-Sn-Ag-Au). The database can be used in conjunction with the FactSage computer platform. The accuracy of the database and its application to industrial practice is demonstrated.