Search Documents

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By D Cliff

"It has been 17 years since the mine disaster at Moura No 2 Mine in Queensland. Recent disasters in the USA and New Zealand prompt the question what has changed since 1994. This paper att emptsto answer this question and identify areas that need improvement."

Jun 1, 2012

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By B Beamish

"All underground coal mines in Australia are required to develop a Spontaneous CombustionManagement Plan (SCMP). The New South Wales Government has developed a guideline (MDG1006) to assist operations to comply with this requirement. A reference document is alsosupplied with the guideline that describes the type of information that is needed for input to theplan, including identifying possible tests that can be used for propensity assessment. However,there is no clear indication of what program of sampling and testing is suffi cient to provide adefi nitive assessment of spontaneous combustion propensity prior to and during mining. This paper reviews the existing methods available for quantifying spontaneous combustion propensity and discusses the sampling requirements that are needed from exploration to mining. A new, more defi nitive method of spontaneous combustion testing is also presented that benchmarks coal self-heating performance from mine ambient temperature to thermal runaway. Examples of the eff ectiveness of this new test method for identifying and quantifying reactive pyrite in coal as well as quantifying the diff erence between dry and wet season conditions are provided in the paper."

Jun 1, 2012

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

By Ciro Manolo Alegre Huamán

El presente texto describe la metodología para el desarrollo del planeamiento de minado subterráneo a través del software minero y de técnicas matemáticas modernas. Así también es importante la base de datos geológica que servirá como soporte para generar los modelos geológicos y geotécnicos a partir de los cuales, se obtiene el modelo de recursos mineros y, consecuentemente, las reservas mineras, que es donde se soporta el planeamiento de minado para una operación minera subterránea.

Jun 1, 2012

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

By Francois Charette

Corrosion is a significant factor affecting the capacity and working life of ground support. The paper explores a relatively simple method to predict the load capacity of a support system using a Monte Carlo stochastic approach. The analysis uses published field data on existing ground support to evaluate the applicability of the method and its predictive performance. Discussion on corrosion rates found in the field and predicted from laboratory measurement is provided.

Jun 1, 2012

By Azadeh Riahi

The main goal of this paper is to investigate the effects of permeability anisotropy in Large Open Pit (LOP) mines for problems that exhibit homogeneous anisotropic characteristics. The most important effect of the groundwater flow in open pit mines is on the stability of the pit slopes. This study will investigate the effects of having increased permeability in both horizontal and vertical directions on three aspects of LOP behavior, location of phreatic surface, pore pressure distribution and stability of slopes. The hydromechanical coupling is simulated using a one-way coupling approach. The Shear Strength Reduction method (SSR) is applied to assess the stability of slopes. The studies performed in this paper suggest that anisotropy in permeability leads to a significantly different regime of pore pressure dissipation depending on two aspects, ratio of anisotropy and the relative magnitude of permeability to simulated time. As a result, variation in safety factors and the location and depth of the failure surface must be expected.

Jun 1, 2012

By Kristine Haug

Although most in situ operations in Alberta do not encounter significant problems during resource extraction, there have been a few documented occurrences of oil or steam releases as a result of compromised caprock seals. The objective of the Oil Sands Caprock Integrity Project (OSCRIP) is to characterize the units above and below bitumen zones to determine which geological factors affect the quality of the caprock seal. In addition, geomechanical properties and stress measurements of the bitumen reservoir and overlying units will be examined to provide a better picture of the containment conditions in which in situ operations occur. The information from this study will aid regulatory staff and industry in determining the zone-specific geological and geomechanical factors that could affect the design, operation, and feasibility of in situ recovery projects. The OSCRIP study area (Townships 87 to 99 and Ranges 1 to 13, West 4th Meridian) encompasses the surface mineable area, the northeast extent of the Wabiskaw-McMurray bitumen deposit and the Clearwater Formation, as well as a wide band of the Devonian salt-dissolution zone. Regional geological mapping of the Cretaceous strata focuses on the spatial extent and thickness of the caprock seal. Mapping of the underlying Devonian strata is targeted at better understanding the potential effects of salt dissolution and collapse of overlying strata on the integrity of the caprock seal. Examination of LiDAR (Light Detection And Ranging) bare earth DEM in the study area has revealed localized depressions that may represent sinkholes rooted in subsurface collapse features in Devonian carbonate and evaporite strata. Mapping the location and understanding the timing of salt dissolution-related features and deformation in the Devonian strata will help address questions about the possible effect that geological structures, such as sinkholes, have on the integrity of the caprock, as well as the potential for localized variations in the stress regime of the bitumen zone and overlying units. The stress regime in units above 350 m is such that any induced fractures are believed to be horizontal, and therefore, there would appear to be no mechanisms that would allow these fractures to reach the surface. However, recent incidents have shown that vertical pathways can occur, linking the subsurface to the surface. The final phase of the project will evaluate the changes that may occur in the stress regime under thermal operating conditions in the study area.

Jun 1, 2012

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012

By Rómulo Mucho

El texto plantea los diversos procesos relacionados con la ejecución de los proyectos de perforación y voladura de rocas. Dado que los requerimientos de prevención de riesgos son "sensibles" desde la perspectiva de seguridad y medio ambiente, es necesario que se realize un planeamiento para minimizar los riesgos a los cuales un contratista está sujeto al momento de realizar trabajos de perforación y voladura en construcción. El planeamiento consiste en organizar los procesos de tal forma que se reduzcan los riesgos. Las actividades que comprende el planeamiento son: análisis matemático y cualitativo, simulación, análisis de precio unitario, calidad, análisis de riesgos, ejecución, análisis de resultados.

Jun 1, 2012

By Bruce Macdonald

Operational reservoir management activities such as cyclical steam, water or CO2 injections frequently cause surface micro-deformation. InSAR monitoring from space based sensors of this surface deformation has become a valuable approach to confirm and monitor extraction and injection activities. Sequestration of CO2 into deep saline aquifers is discussed as an important long term solution to slow future climate change. This method requires reliable continuous monitoring to assure that captured CO2 is sequestered in the substrate for ?all time? (typical minimum requirement by law is 20-30 years). We have shown that combining flow and deformation modeling with spaceborne synthetic aperture RADAR interferometry (InSAR) measurement of ground uplift caused by the underground release and spreading of the CO2 can be forged into a powerful tool to monitor sequestration. We used a novel InSAR approach to resolve the surface motion over the In Salah, Algeria CO2 sequestration site. Our approach exploits all information contained in an interferometric stack by exploiting both persistent distributed as well as persistent point scatterers. Displacement time series are obtained with a network inversion approach applied after topographic error and preliminary atmospheric correction of the network (dual-scale technique). After inverting the original network data to common master we then use an advanced spatio-temporal filtering scheme to remove the remaining atmospheric phase components down to scales of 1 km or less. By comparing final displacement series from multiple interleaving InSAR stacks we show that the accuracy of our refined solution to detect uplift outside of significant temporal data gaps in the InSAR stack is significantly better than 1 mm per year. We further show that accuracy and robustness to data gaps are both significantly improved by co-inverting multiple datasets with the same and different sensors. This co-inversion method also allows the seamless continuation of the monitoring from one sensor to another.

Jun 1, 2012

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By Jaime Meléndez Martínez

Recent interest in unconventional reservoirs motivates our work in laboratory measurements of seismic anisotropy. Seismic anisotropy is the variation in speed of a wave as a function of its direction of propagation. Analyzing anisotropy in unconventional reservoirs is important since anisotropy leads, for example, to differential stresses upon loading and could affect hydraulic stimulation (Reinicke et al., 2010, Zimmermann and Reinicke, 2009); in this sense, laboratory measurements are an important tool to study seismic anisotropy at small scales which can aid in the characterization of larger formations. The purpose of this work is to describe the laboratory methodology used to simultaneously measure ultrasonic P and S-waves in three different directions from a single core sample. Elastic anisotropy of a Proterozoic sedimentary rock from south-west Alberta is investigated. In metamorphic rocks seismic anisotropy is caused by preferred mineralogical alignment or foliation. Assuming a transversally isotropic medium, arrays of compressional and shear piezoelectric ceramic transducers were mounted on a sample trimmed from a core to measure travel times of ultrasonic P-waves and S-waves as a function of confining pressure at directions perpendicular, parallel, and oblique to the plane of foliation (bedding). Results show strong anisotropy agreeing with the assumption of a transversely isotropic medium. Dependence of travel times and hysteresis effects can be observed when pressurizing and depressurizing.

Jun 1, 2012

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012

By B Belle

"Mines around the world are inherently and operationally diverse. Current methodologies for the design of mine ventilation and cooling infrastructure involve controlling major safety and health hazards. Globally, it can be estimated that mine ventilation systems from various commoditiescirculate over 150 000 m3/s of exhaust air through shafts. Additionally, over 2 000 000 workersare transported every day through shafts in labour-intensive mining countries like China, India,Southern Africa, and the Americas. A key objective of this paper is to share experiences and provide a case for the revision of ætime-honouredÆ ventilation design parameters based on a benchmarking exercise on design exhaust shaft velocity from various global operations (gold, diamond, platinum, coal and base metals). An active fi eld observation on exhaust shaft velocity has indicated that, regardless of the commodity or continent where the mine operates, almost all life-of-mine (LOM) design parameters provided are in the same range of 20 m/s to 22 m/s, which is not convincing considering signifi cant variations exist in shaft depths, geography, commodity, operating and capital costs. From a due diligence perspective, there are no documented views that are available on the most widely used design exhaust air velocity. Based on the global exhaust shaft velocity data, it is noted that a significant portion of shaft velocities are outside the current design velocity of 20 m/s (some operating up to 30 m/s) and other signifi cant portions of the exhaust shafts operate in the critical velocity range. In the case of Australian coal mines, limited data suggests that none of the mines have ever reached the LOM design exhaust shaft velocity. It is self-evident that when the shafts are not operating at their design quantities either the mine system resistance is low or the ventilation and main fan is operating ineffi ciently. The most common reasons given for not reviewing the shaft system were, ætime-honouredÆ design parameter are being used and cannot be changed, mine fan pressure limits, possible fan blade damage, possible spontaneous combustion risks, leakage or simply did not consider such a possibility. In conclusion, the study has reiterated the historic lessons that a safe and expensive airway should not be utilised uneconomically by circulating too litt le air through it."

Jun 1, 2012