Search Documents

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By C. Çelik

Nowadays the optical sorting of industrial minerals is one of the most important processing methods which has cost efficient production possibilities. This method is used for industrial and raw materials that have different colour and brightness features. Initially this technology is used for sorting of foodstuffs and recovered glass, but for a long time also as physical mineral processing method for both industrial minerals like: limestone, marble, talc, basalt, flint, quartz and secondary raw materials like: building rubble, refractory materials, glass, plastic and household waste. In this study via optical sorting the separation of quartz out of a flint mix, which consists of the particles with different colors and brightness, is aimed. Experiments are performed on an optical sorting machine named CombiSense® 1200 at the institute of ?Aufbereitung mineralischer Rohs-toffe? RWTH Aachen. This automatic picking device was developed by the company ?Separation Systems Engineering (SSE), Wedel?. Hand picking method is used for product analysis and the efficiency tables are prepared on every step accordingly. This process enables to reach quartz products with purity up to 100%.

Jan 1, 2014

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014

In the wake of the financial crisis that affected world markets in 2002, there has been an increasing international focus on corporate governance. Various corporate governance codes of practice have been introduced, such as the Sarbanes-Oxley legislation in the USA, the Combined Code in the UK, and King III in South Africa. This focus on corporate governance has increased since the most recent financial crisis in 2008, the effects of which are still being felt world-wide. In the mining and minerals industry, reliable metal accounting is essential to sound corporate governance and is also becoming a focus of increased attention and concern, particularly as the figures generated by the metal accounting system feed directly into the financial accounts of mining companies. Mass measurement, sampling, and analysis provide the input data for the metal accounting system and sound corporate governance requires that the procedures used are based on best practice and that the data generated is accurate and handled correctly, transparently, and consistently to produce the accounting reports. The AMIRA Code of Practice for Metal Accounting has been widely adopted in the industry as a means to achieve this, and the compilers of the Code have conducted numerous metal accounting audits at operations, both in South Africa and abroad. These audits have shown that there is a real need for such a code of practice. Keywords metal accounting, AMIRA Code, corporate governance, risk management.

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth's crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

By K. Soldenhoff, D. Wilkins, E. Ho

In the processing of rare earth ores, a pure, mixed rare earth chloride solution is usually produced and used as the feed to solvent extraction circuits to separate the individual rare earths. Cerium(III) may be separated from the other rare earths by oxidising it to cerium(IV), which precipitates as cerium(IV) hydroxide in chloride liquors. This oxidation step may be inserted either before rare earth separation by solvent extraction or between solvent extraction circuits. Although oxidation of cerium by sodium hypochlorite has been known for many years, detailed conditions for oxidation are not readily available. The effect of hypochlorite addition, temperature, pH and cerium concentration on oxidation of cerium(III) from synthetic solutions was investigated

Jan 1, 2014

By Patricio Berrios, David Barriga, Peter Amelunxen, Gerson Sandoval, Roger Amelunxen

Laboratory test equipment and methods have undergone relatively little change since their introduction in the 1950’s. The Denver sub-A cell is still by far the most commonly used laboratory batch cell, but bottom-driven and instrumented cells are beginning to appear. Test procedures have also changed little over the past 60 years, and most engineers continue to rely on empirical models for predicted plant scale performance from laboratory scale tests. This approach is problematic, because changes in the froth phase characteristics in the lab hamper the reliability and reproducibility of the empirical extrapolation to plant scale. In a previous work, the authors reported on the impact of froth recovery at the laboratory cell, showing that variability in the froth recovery can lead to significant error in the modeled kinetic rate constant unless it is properly accounted for in the scale-up model. In this work, we review the role of hydraulic entrainment in the lab cell, and how variability in particle specific gravity, shape factor, and froth residence time can impact the entrainment recovery.

Jan 1, 2014

By Jiongtian Liu, Guixia Fan, Caom Yijun

A cyclonic-static micro bubble flotation column (FCSMC) is an effective separation device for fine grain treatment. The separation of fine ilmenite by FCSMC was explored in this work. The influence of reagents dosage (regulator, collector and auxiliary collector), pulp density, circulation pressure and aeration quantity on TiO2grade and recovery wasinvestigated.The optimal conditions of a rougher are follows: pulp density 45%, pH 5.0, MOH collector dosage 2800 g/t, diesel oil dosage 700 g/t, circulationpressure 0.19 MPa, aeration quantity 0.8 m3/(m2•min). The optimal conditions of a cleaner are follows: pH 4.0, circulation pressures 0.16 MPa, and aeration quantity 0.5 m3/(m2•min).A pilot plant continuous test with a rougher-cleaner by FCSMC for 72 hours was proceeded under the optimum conditions. Compared with industrial flotation machines, the concentrate grade of FCSMC is 48.11% with an improvement of 1.08 percentagepoints, while the recovery is 82.36% with 13.64 percentagepoints increment. Moreover, the flowsheet is simplified from six parts (a rougher-two scavenger-three cleaner) in flotation machines to two parts (a rougher-cleaner) in FCSMC. Proofs were also provided by the analysis of the by-size grade and recovery of concentrate.Results show the FCSMC is an effective separation device to recover -74 µm size fraction.

Jan 1, 2014

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

"SAMPLING: THE IMPACT ON COSTS AND DECISION MAKING1. INTRODUCTIONFor years those in the minerals industry have been taking samples to assist them in making decisions; whether they be about investing billions of rand in a new mining operation, or simply whether a truck load of mineralised material should go to the mill or the waste dump, - we need a sample to help us make our decisions. This paper emphasises the importance and significance of sampling as a process, some of the associated technical problems and some of the advantages, especially in the light of traditional approaches that has usually left mine sampling to the least educated and lowest paid individuals on the mine. Perhaps the most important aspect that requires attention is the variability, usually measured in terms of precision, that tends to infect the sampling procedures. Francis Pitard 12 has stated: ""There is no such thing as reliable feasibility studies, unbiased ore grade control, accurate environmental assessments or effective process control, if you cannot identify and minimize the seven (ten) major sources of sampling variability. "" It is these ten sources of sampling variability and the way they arise that are briefly investigated. Variability is measured in terms of variances and rather than being self-compensating, there is good evidence to indicate that they are in fact additive at every step in the sampling and analytical process."

Jan 1, 2014

By Paul B. Crawford, Gerald N. Pitts

"A new method is introduced for the simulation by computer of the flow of liquid underground. The method has application in simulating, for example, liquid withdrawal systems, injection systems or injection-well systems. The computer simulation of liquid flow permits the utilization of the known properties of the rock in developing a model of the permeable rock mass.The flow properties of the rock at a specific site arc generated statistically using a random number generator. After defining in this manner the rock properties of each element in the computer grid, the streamlines or flow paths of the liquid are traced using the new method. The simulation is designed especially for computers. The meandering character of the liquids paths is displayed clearly as the fluid moves underground, thus providing the technical information required for the control of the movement of liquid."

Jan 1, 2014

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By S. L. Zheng

The compound material of Nano-TiO2 Supported on the diatomite was prepared by the hydrolytic method with purified diatomite and TiCl4. The compound material was characterized by SEM, XRD, TEM, EDX, XPS, and the application test of the compound material was studied. The characterization test results showed that the Nano-TiO2 was coated on the surface of diatomite, the crystal of TiO2 is anatase, and the average crystal size is 12 nm. The pore diameter was reduced, but pore volume and surface area of the compound material are increased after Nano-TiO2 Supported on the diatomite. The application test results for treating coking waste water and formaldehyde gas show that the compound material of Nano-TiO2 / diatomite has adsorption and photo-catalytic function and strong degradation performance for phenol and formaldehyde.

Jan 1, 2014

By A. V. Byvaltsev

Adsorption of cyanide complexes of gold, silver, copper, mercury, nickel, cobalt, iron, zinc and cadmium has been studied. Adsorption isotherms of the mentioned metals from individual solutions for different free cyanide concentrations have been obtained. Values of the constants of Freundlich isotherm equation have been calculated. Metal cyanide complexes affinity to activated carbon was determined.

Jan 1, 2014

By Carlos A. Prato, Federico Pinto

"ABSTRACTThe design of drilled shafts often incorporates large factors of safety, for which settlements under service loads are highly influenced by the initial elastic stiffness. In the case of groups of drilled shafts with typical spacing, the elastic shaft-soil-shaft interaction dominates the behavior even for loads close to the bearing capacity, for which the initial stiffness is a key parameter in the design. This paper describes typical trends in results obtained by means of different approaches currently available in the literature for the evaluation of the initial stiffness of a single shaft. An experimental technique that provides a rapid and inexpensive means for the evaluation of the initial stiffness is described, and the results obtained for typical cases are compared with analytical predictions.IntroductionThe behavior of drilled shafts under axial loads is generally governed by the initial stiffness, as the factors of safety considered in design are often large, due to a superposition of conservative assumptions on soil properties and expected loads. In the case of shaft groups, the initial elastic stiffness plays a major role together with the elastic group effects, as nonlinearities tend to localize around the shafts and have a lesser effect than elastic deformations on adjacent elements (e.g., Leung et al., 2010). An accurate characterization of the initial stiffness is thus warranted for the analysis of drilled shafts and shaft groups under service loads.Initial stiffness of shafts may be estimated on the basis of soil stiffness and structural properties of the element by means of numerical methods (e.g., Pinto and Prato, 2006), as well as analytical methods (e.g., Randolph and Wroth, 1978). The soil stiffness may be determined by means of geophysical tests (e.g., Spectral Analysis of Surface Waves, SASW, Stokoe et al., 1994), or correlations with Standar Penetration Test (SPT) blowcounts or Cone Penetration Test (CPT) resistances (e.g., Sabatini et al., 2002).The initial stiffness may also be measured on drilled shafts by means of load tests. Static load tests (SLT), however, have some limitations on measuring small deflections, for which the initial stiffness is often extrapolated by means of large strain measurements (e.g., Chin, 1970), where the SLT measurements are more accurate."

Jan 1, 2014

By X. G. Liu

Bentonite is an excellent sealant mineral material because of its desirable swelling and self-healing characteristics, low permeability, sorptive qualities, and longevity in nature. A new type of water-swelling building sealant made from bentonite was studied in this paper. The building sealant is prepared by Na-base bentonite, vaseline and paraffin wax under different mass fraction of bentonite (which is 60%,65%,70% respectively). Under unrestricted state, some properties of samples were investigated. The volume expansion ratio at 24 h is 211%, 222%, 256% , and permeability coefficient is 2.86×10-8 cm/s, 4.15×10-8 cm/s and 4.78×10-8 cm/s respectively; low temperature flexibility of the sample (bentonite quality is 65%, 70% respectively) is good, and it does not flow heated for 2 h under 80?. The results of XRD and SEM indicate that bentonite is coated preferably by vaseline, and the spacing of layers of bentonite do not changed. The sample can keep full water swelling ability, and has good molding process. The test results prove that the properties of samples may reach the standard of building sealant.

Jan 1, 2014

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014