Search Documents

By J. C. C. C. Menezes, R. A. S. Silva, A. V. Colling, I. A. H. Scheneider

"Coagulants rich in ferric sulfate can be obtained from pyrite-containing coal tailings using a biohydrometallurgical process. The aim of this study is to evaluate the relationship between quantity of pyrite and rate of oxidation, with regard to the consequent production of ferric sulfate for potential use as a coagulant for water and wastewater treatment. Leaching experiments were carried out on the laboratory scale on four coal tailings with different concentrations of pyrite. Characterization of the coal tailings was conducted for the following parameters: total sulfur, pyritic sulfur, sulfate sulfur, organic sulfur, and elemental analysis of CHN (carbon, hydrogen, nitrogen). The samples were also subjected to X-ray diffraction analysis to assess their mineral compositions. The leaching experiments were accomplished using a laboratory column constructed as a packed bed reactor with a sprinkling system in a closed circuit. After four weeks of leaching, the liquor was filtered and evaporated to an iron concentration of about 12 percent w/w, which is typical of the ferric sulfate coagulants commercialized in Brazil. IntroductionCoagulants used for the treatment of water and wastewater are predominantly inorganic salts of ferric iron and aluminum. Aluminum salts, including aluminum sulfate and aluminum chloride, and prehydrolyzed metal-ion reagents, such as polyaluminum sulfate (PAS) and polyaluminum chloride (PAC), are the coagulants most widely used for water treatment (Bratby, 1980; Tchobanoglous et al., 2003; Buzin et al., 2014).However, the presence of residual amounts of aluminum in drinking water has been controversially implicated in neurological diseases (Association of California Water Agencies, 2000; Becaria et al., 2006; Campbell, Hamai and Bondy, 2001; Rondeau et al., 2000; Walton, 2006). A possible alternative is to use iron-based coagulants, such as ferric chloride, ferric sulfate or polyferric sulfate, instead of the aluminum salts (Jiang, Graham and Harward, 1996; Jiang and Graham, 1998). Iron-based coagulants are commonly produced by the acid dissolution of iron scraps or iron ore (Tchobanoglous et al., 2003).Recent studies have shown that it is possible to produce ferric sulfate coagulants from the pyrite present in coal tailings through a biohydrometallurgical process (Colling et al., 2011). The main advantage of this process is that it does not require acid addition, which can be favorable in terms of production costs. Acidophilic bacteria, such as Acidithiobacillus ferrooxidans, can increase the rate of pyrite oxidation and dissolution by several times (Kontopoulos, 1998; Brett and Jillian, 2003; Johnson and Hallberg 2003). They can be highly significant in the bioprocessing of coal tailings for the production of ferric coagulants, as their action favors the acidification of the medium and iron leach (Colling et al., 2011)"

Jan 1, 2016

By Z. Luo, China University of Mining & Technology, C. Duan

"The magnetic separation removal rate of pyrite could be improved effectively by increasing the susceptibility of pyrite. The electromagnetic characteristics and absorption response performance of high-sulfur fine coal were studied in strengthening the susceptibility of pyrite. In the process of treating the sample through the microwave, electromagnetic energy could be converted into heat energy due to dielectric loss and magnetic loss. The RL(dB) was evaluate the performance of absorption response of coal. The microwave improved the susceptibility was in ultra-high frequency region, which is the most natural resonance. The absorption fine coal to microwave was strengthened and microwave energy was improved by adding the magnetite powder with double loss characteristics as the microwave absorber. The dielectric properties and permeability characteristics of the fine coal trend were investigated by maxing magnetite powder. The microwave absorption in different coal thickness was surveyed through the reflection of energy loss.INTRODUCTIONMicrowave desulfurization is one of the most important research directions (Haque, 1999; Makul, Rattanadecho, & Agrawal, 2014; Su, Tang, Zhang, Jing, & Bai, 2014). The working principle of microwave absorption response can be briefly described as the interaction of the sample with microwave energy, which will result in the microwave energy converting into heat energy loss (Keangin & Rattanadecho, 2013). For specific samples, the polarization effect includes multiple polarization mechanisms(Meikap, Purohit, & Mahadevan, 2005). Different polarization mechanisms have different occurrence time and dominant mechanisms. Meantime, energy consumption will be occurred during the process of polarization effect (Chelgani & Jorjani, 2011; Rowson & Rice, 1990) . The absorption of microwave energy in the fine coal is a process of electromagnetic response (Znamenácková, Lovás, Mockovciaková, Jakabský, & Briancin, 2005). Microwave transfers the electromagnetic waves into the heat energy by microwave dielectric loss and magnetic loss for achieving the absorption of microwave energy in the treatment of samples (Lee, Kim, Kim, Chung, & Kim, 2004). The additive magnetic medium is Fe3O4 belonging to microwave energy absorber of double loss medium (Uslu, Atalay, & Arol, 2003)."

Jan 1, 2016

By G. Girard, A. Larouche, J. Colbert, G. Doyer

"The Direct Chill (DC) casting process uses water to extract heat from molten aluminium and helps to control the solidification process. Many factors such as the water flowrate, water distribution around the mould and water impingement angle have significant impacts on the solidification process. It has been noted that the chemistry variation of the cooling water is also an important factor that has a major impact on the presence of defects on the ingot. A significant change in the water quality can produce defects on the ingots such as cracks, bleedouts, or runouts. Understanding the impact of water quality variation on ingots is therefore essential to ensure good ingot production and reduce defects. This paper aims at describing a new approach to follow the variations of process water quality over time. It is an original and innovative method, which is still under progress. A water quality and stability index (WQSI) is under development to evaluate changes in the water composition based on water physico-chemical parameters. The index is calculated by comparing each of the actual parameters with historical values previously modeled by a statistical law. It is a dimensionless number having an adjustable weight factor for each parameter. The positive or negative contribution of each parameter, with respect to the water cooling capacity, is taken into account to calculate the WQSI. The current selection of parameters is based on knowledge from the literature as well as on empirical experience. When the developed tool will be mature, it could be used to track water variations upon time and anticipate problems, enabling proactive actions to ensure good ingot production.INTRODUCTIONFor many years, the impact of water chemistry on heat transfer, during DC casting, has been of great interest in the aluminum industry. Several papers have been published to demonstrate the correlation between water chemistry and heat transfer (Yu, 1985), (Gildemeister, 2014). Although numerous studies do present the effects of water parameters (i. e. hardness, conductivity, oil, and grease…) on cooling capacity under controlled experimental conditions, they do not reflect the strong interactions between the parameters and variations present in a casting center. Wells and Cockcroft also demonstrated that laboratory based studies are not fully representative of real heat transfer in an industrial casthouse, there are too many factors involved (Wells, Li, & Cockcroft, 2001). In this context, it becomes very difficult to obtain a quantifiable relationship between the capacity of water to cool the ingot and ultimately the performance of the cast."

Jan 1, 2016

By T. S. Lundström, B. D. Marjavaara, I. A. S. Larsson

"The flow field in a rotary kiln, used in an iron ore pelletizing process, was investigated using a three-dimensional computational fluid dynamics model. The model is isothermal, downscaled and simplified. The objective was to examine the possibility of capturing the unsteady motion of the flame seen in the real kiln. The results from the simulations were compared with recorded images of the real process. The results demonstrate the possibility of quickly getting an overview of the flow field in the kiln. The main, unsteady behavior of the flame was captured. The model may be used as a tool in the ongoing work of improving and optimizing the pelletizing process.IntroductionThe pelletizing process, in which the crude iron ore from a mine is upgraded into pellets, is a process involving large amounts of hot air flowing in complex geometries. Flow control is a crucial factor in this process to maintain high pellet quality. The rotary kiln is one of the last steps in the pelletizing process, and this is where the pellets are sintered to increase their strength and metallurgical properties. The kiln burner produces a flame that supplies the entire pelletizing process with the necessary heat.Kiln burner flames are large diffusion flames arising from a jet of fuel from the burner issuing into a concentric confining cylinder with a surrounding coflow of air, called secondary air. To enable combustion, the secondary air needs to be entrained into the fuel jet. This mixing of the fuel and air is the slowest step in the combustion process and therefore affects the efficiency of the combustion. The rate of entrainment depends on the momentum ratio between the burner jet and secondary air. The higher the momentum ratio, the faster the entrainment rate and, consequently, the faster is the fuel/air mixing.The kiln of interest in this study differs from kilns used in other industrial processes in both geometry and operating conditions. A distinguishing feature is the large amount of secondary air being induced through the kiln hood and then transported to earlier stages in the process as air or exhaust gas. The secondary air therefore has a substantial momentum, implying that the resulting flow field has a significant impact on the mixing and combustion process in general and the flame shape and stability as well as combustion efficiency in particular. A systematic study of the factors influencing the dynamics of the flow field in the kiln, neglecting the combustion, is therefore justified."

Jan 1, 2016

By K. Turgeon, D. Larivière, L. Whitty-Léveillé, J. -F. Boulanger, C. Bazin

"The processing of ore containing rare earth elements leads to the production of an impure solution of these elements. The separation of the rare earths from the impurities and the production of individual elements is usually carried out by solvent extraction. The effectiveness of the extraction conditions and of the reagents is generally tested in the laboratory. This paper deals with the processing of results from solvent extraction laboratory tests planned to generate data redundancy. A method is proposed to take advantage of the data redundancy by accounting for the pH variation during the extraction. The parallel processing of several tests also allows estimating the equilibrium constants for the extraction. The proposed method produces equilibrium constants that are more reproducible than values estimated using conventional approaches. The method is illustrated with solvent extraction tests conducted on synthetic solutions of rare earth elements.INTRODUCTIONThe processing of ores containing rare earth elements (REE) usually includes the production of a concentrate of the minerals carrying the REE. These minerals, for instance monazite and bastnäsite, contain the 14 elements from La to Lu plus yttrium and scandium. As an example monazite has the general formula of (La,Ce,Pr,Nd,Sm,Eu,Gd,Tb,Dy…Lu)PO4 with a typical lanthanum content of 20-26%, cerium content of 40-50%, praseodymium of 4-6%, neodymium of 16 to 20%, and decreasing concentrations of heavier elements (Gupta & Krishnamurthy, 2005). During the processing of a REE mineral, it is generally not possible to isolate and separate a single REE from all the rest. The mineral molecules need to be broken (usually via a heat treatment followed by leaching with a base and/or an acid) to produce an aqueous solution of the REE of the ore. After purification of the solution, the REE can be precipitated as a bulk concentrate and sold to a refinery that separates the REE into particular groups of REE such as the light versus heavy REE or into individual elements such as lanthanum, neodymium, or europium oxides to yield value-added products."

Jan 1, 2016

By I. J. Burgess, B. C. Barlow

"The electrodissolution of nickel pellets with different controlled electrical variables was investigated in an effort to mitigate plating residue in Watts bath based electroplating cells. During galvanostatic dissolution at 0.4 A dm-2, the anode potential was seen to oscillate between passive and pitting potentials. In-situ microscopy and ex-situ characterization has shown that lacy-pit formation and large, partially perforated, pit covers form during the potential decay from pitting potentials. In general, covered pitting at low current density shows increased plating residue. Using potential pulses is one way to maintain greater control over surface pitting by creating a higher density of pit nuclei while at the same time controlling their growth. Pits generated from a series potential pulses were examined ex situ for a range of pulse times and stages of pit growth were identified. An alternative method of anode dissolution was devised using potential pulses and duty cycles that allowed average current densities comparable to industrial plating conditions to be achieved. By restricting the time at pitting potentials to 0.05 s, plating residue was reduced more than six-fold in comparison to an equivalent galvanostatic experiment run at a comparable current density.INTRODUCTIONIn typical galvanostatic (direct current) nickel electroplating cells employing soluble anodes, some amount of plating residue is produced which consists of metallic nickel and impurities that detach from the bulk in the form of small fines. Significant buildup of residue requires plating operations be halted and the anode assembly cleaned of residue before operation can resume. While variables in the refining process have been shown to affect plating residue, more precise control of electrochemical variables may provide an attractive route to mitigation of residue."

Jan 1, 2016

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclone separators are used in various industrial applications, including mining milling and tailings systems, in order to separate or classify solid particles and liquid droplets from multiphase systems. The flow within a hydrocyclone commonly used in the mineral processing industry was investigated numerically and experimentally using Particle Image Velocimetry (PIV) and refractive index matching techniques. The computational simulations were performed using a commercially available CFD package, STAR CCM+. Two turbulence models were used in the numerical calculations: the k-? model and the Reynolds Stress Model (RSM). In both cases, the first order discretization scheme was unable to resolve the flow characteristics accurately due to the high levels of numerical dissipation. PIV measurements were taken at various spatial locations along the cyclone. Both the numerical simulations and PIV data demonstrate that tangential velocities tend to increase when going radially inward from the cyclone wall towards the vortex finder, and reach a maximum value before they begin to decline rapidly and eventually become zero at the wall. The results also demonstrate the utility of non-axisymmetric approaches in cyclone flow simulations for a greater understanding of the fluid mechanics. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. The comparisons demonstrated good agreement between the two models.IntroductionHydrocyclones are devices used to separate and classify solid particles or liquid droplets from liquid-solid or liquid-liquid systems. Versatile in application, they have been widely used in many industrial applications including the food, oil, power generation, chemical and mineral processing industries since 1891, when the first hydrocyclone was introduced by Bretney (Park, 2003). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2016

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By Bern Klein, Tichang Sun, Daozhen Gong, University of Science and Technology Beijing, Chunbao Sun, Stefan Nadolski

"This paper is focused on the effect of modifying the SAG mill/ball mill transfer size on the energy efficiency of SABC circuits. The transfer size is considered to be a parameter which provides operators with the opportunity to improve comminution circuit performance. In this study, the Moly-Cop tools package was employed to predict the energy consumption of SAG mill and ball mill circuits under different operating conditions. An Energy Benchmarking model was adopted to calculate grinding energy efficiency. The SABC circuit at the Huckleberry mine was selected for this case study. It was observed that after increasing circuit transfer size (T80) from the existing 3.3 mm to 4.8 mm, the Benchmark Energy Factor (BEF) of the SABC circuit decreased from 4.30 to 4.05. In terms of energy consumption of the SABC circuit, 1.17 kWh/t of specific energy saving was achieved through the transfer size optimization.It was also observed that when a transfer size was selected such that both SAG mill and ball mill circuits operated at their highest energy efficient states, the entire SABC circuit was the most energy efficient. The maximum energy efficiencies of these three circuits were all approximately 25% when compared to the minimum practical energy required to carry out an equivalent comminution duty. Single-particle compression breakage testing was used to determine the minimum practical energy associated with the Huckleberry mill feed. In combination with geo-metallurgical data, this study also provides an opportunity to perform dynamic optimization of SABC circuits."

Jan 1, 2016

By D. S. Flett, A. V. Tolstov, M. A. Mulagaleeva, N. V. Gudkova, A. M. Zhizhaev, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina

The complex niobium-rare earth pyrochlore-monazite-crandallite ores of the Tomtor deposit, located in the Siberian Arctic, should be considered as a new type of rare metal materials. The major valuable components of the ore are niobium, rare earth elements, yttrium, and scandium; associated components are titanium, vanadium, aluminum, and phosphorus. Because of the irregular distribution of the rare earth metals and niobium according to grain-size, the extremely finely dispersed nature of the minerals and their close interpenetration to each other, ore processing by gravitation and flotation is not successful. The processes studied for the treatment of the Tomtor ores use direct alkaline-acid leaching to open the ore. A problem in the first stage of alkaline leaching is the high aluminum content, which decreases the activity of sodium hydroxide and alkaline-earth metals, which are bound to phosphorus. Ore processing using alkaline-nitrate and alkaline-chloride leaching was proposed and investigated. The first variant was used to obtain rare earth and scandium materials and a niobium-titanium concentrate, which can be a stock material for processors who use chlorination for the processing of ores and concentrates. The second variant is a complex advanced ore processing scheme with electrochemical regeneration of the waste chloride solutions obtaining sodium hydroxide, hydrochloric acid, and chloridizing agents. Moreover trisodium phosphate is used for purification of the waste mother liquors from metal cations. The complex salt, NaAlCl4, is proposed as the chloridizing agent for the decomposition of the niobium-titanium concentrate.

Jan 1, 2016

By Y. Wang, J. D. Miller, C. L. Lin, Virginia Tech

Conventional flotation machines are typically limited to a particle topsize of 150-200 microns due to inherent constraints created by the pulp and froth phases. To overcome these limitations, a novel fluidized-bed flotation system called the HydroFloatTM Separator has been developed specifically for the purpose of floating coarse particles containing only small amounts of exposed hydrophobic minerals. Over the last decade, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3,000 microns diameter. More recently, sulfidebased test work has shown that this novel device is also capable of recovering metalliferous values at a grind size that is much coarser than currently used in industrial concentrators. In the current study, high resolution X-ray microtomography (HRXMT) was used to experimentally compare the degree of exposed grain surface area necessary to recover coarse particles using the HydroFloatTM technology to that attainable using a traditional mechanical flotation cell. The data indicate that exposed grain surface area is a critical factor for coarse particle flotation. For the gold-bearing sulfide ore examined in this study, the HRXMT data suggest that near complete recoveries of coarse (850x500 µm) multiphase particles containing as little as 1% exposed grain surface area were realistically attainable using the HydroFloatTM technology. As such, this new technology may offer a unique opportunity for increasing concentrator capacity by increasing the primary grind size needed for rougher/scavenger separations.

Jan 1, 2016

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By J. Châteauneuf, R. Dupéré, D. Mrabet

"In gold processing plants, it is common to start gold cyanidation in the grinding circuit by simple cyanide addition or as a result of recycling residual cyanide. In such cases, advantages such as a decrease in gold lockup and reduced leach time have been noticed. The prevailing conditions in grinding circuits such as intense mixing, particle breakage and friction or high temperature are quite different from those found in tanks and so is the resulting cyanidation behaviour. To gain a better understanding of the cyanidation behaviour in mills and of the pertinence of cyanide addition in grinding circuits, lab tests were conducted using an industrial ore from Canadian Malartic mine. In this study, the effects of different parameters on cyanidation in grinding circuits were examined; parameters such as such as temperature, dissolved oxygen, cyanide concentration and pH. The results showed that the kinetic benefits of high temperature in the mill can overcome the low dissolved oxygen concentration thus leading to an overall gold dissolution kinetics improvement for temperatures up to 50°C. However, gold leach in the studied grinding circuit at lab scale caused an increase in cyanide consumption with a higher generation of iron cyanide and SCN-. These results were confirmed by tests in the Canadian Malartic plant where the cyanide addition was moved from the SAG mill to the leaching tanks resulting in a 20% savings in cyanide consumption.IntroductionCyanidation in grinding circuits can benefit gold processing by decreasing gold lockup and by reducing leach time. However, other aspects regarding gold and cyanicide dissolution come into play in the conditions prevailing in grinding circuits. Indeed, high turbulence, high temperature, recycling load, friction and particle breakage make cyanidation behaviour in grinding circuits different from in-tank cyanidation (Marsden and House, 2006). In several cases, cyanide in grinding is limited to a very low level or completely avoided such as in circuits with gravimetric separation, for ores requiring oxidative pretreatment or for preg-robbing ores. In other cases, water management imposes a certain recycling of residual cyanide. This problem is generally addressed by a case-by-case approach. However, the chemistry of cyanidation in mill circuits is worth investigating in order to assess the advantages and disadvantages."

Jan 1, 2016

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

"During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests.In the current case, a composite sample of gold ore is dedicated to a Gravity Recoverable Gold (GRG) test. The properties of interest are the head grade of gold, the size distribution of the material, and the gold assay per size class. The sample is mixed and a sub-sample is taken to measure the feed properties: the size distribution and the gold assay per size class. The remaining material of the sample is subject to the first stage of concentration using the laboratory Knelson concentrator. The concentrate is analysed in its entirety, while a sample of tailings is taken for the same analysis. The remaining part of tailings is subject to grinding to feed the second and third stages of concentration. Similar sampling is performed at each stage.The concentration performances are analysed in light of these measurements. But what is the accuracy of the measurements of the properties? Pierre Gy’s theory of sampling, associated with a heterogeneity model built using the GRG test results, will answer this question. The current paper presents, through a real example, the calculation of the errors of the measurements of size distributions and gold assays performed during the GRG test. The uncertainties of the concentration performances and liberation size estimate are then calculated and their impact on the results interpretation is analysed.INTRODUCTIONDuring the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests. In order to take into account the ore variability in terms of gold deportment, it is recommended to perform variability studies (Dominy, Murphy, & Gray, 2011, Dominy, 2013) using samples representing various horizons or years of production. But for a given ore type, it can be necessary to perform many tests with different operating conditions (Brochot, 2012a). In that case, the variability of the samples is not due to the heterogeneity of distribution of the deposit, but only on the heterogeneity of constitution of the primary sample. The level of confidence associated with the estimated performance parameters is directly linked to the overall error (including sampling error) of the measurements performed during the tests."

Jan 1, 2016

By Adam Moore, Ryan Gillespie, Jarrett Quinn, Audrey Walters, Peter Radziszewski

"Vale Long Harbour Processing Plant (LHPP) was designed to process Voisey’s Bay nickel concentrate into finished nickel and associated copper and cobalt products. The plant includes a secondary grinding circuit comprising two Stirred Media Detritors (SMDs) operating in parallel. The ultrafine grinding circuit was designed to process concentrate at a rate of 33 t/h and produce a ground product (P80) of 20 µm to feed the leach circuits. Start-up of the grinding circuit at LHPP was undertaken in December 2014.The objective of this paper will be to describe the design, commissioning, start-up and performance of the secondary grinding circuit with a focus on the two Metso SMD-355-C mills. Following a brief overview of Vale’s LHPP and the SMD technology, the paper will review the design of the SMD secondary grinding circuit from lab tests through to scale-up performance prediction. This will be followed by the results of circuit commissioning outlining some of the issues raised and addressed after which SMD performance will be outlined. Specifically, the SMD circuit grinding performance will be examined since start-up which will include the effect of media size and wear on grinding. Furthermore, impeller wear will be examined by determining initial “shear volume” and worn “shear volume” as well as its effect on mill power and the means to maintain it. The paper closes with a discussion on grinding performance."

Jan 1, 2016

By T. Lupek, M. Buxton, A. de Jong

"With regard to the EU funded project ‘Real-Time Mining’ a sensor-based acquisition, collection and transmission of data for the resource extraction process will be developed. The key concept promotes the change in paradigm from a discontinuous to a continuous process monitoring. Especially concerning material characterization, machine performance and underground positioning ‘Real-Time Mining’ will provide sensor solutions as well as the interfaces for integration, management and visualization of the collected data for a permanent updating process of the resource model with the aim of near real-time optimization of decisions. On the basis of ‘Real-Time Mining’-Output a permanent monitoring of costs can be performed as well in both, the installation and the production process of a mine. Due to the collected data in terms of machine performance connected with the underground positioning information added with personnel tracking and mine surveys a comprehensive overview of process performance is available. By evaluating those information in a specific manner costs per unit will arise for monitoring and possibly controlling actions. INTRODUCTION By having a look into the future of mineral extraction projects, a new challenge for the Ore Mining Industry will arise in the short and medium term. Due to the depletion of currently mined mineral reserves in addition to the persistently high demand of mineral raw materials, the extraction of complex reserves will be necessary. By characterizing such deposits as not constantly graded and geometrically varying, the extraction process, especially concerning the requirement of a minimized zero-value material handling, will become economically ineffective by utilizing the traditional mineral resource management methods. Regarding the state-of-the-art mineral resource management process along the mining value chain, an intermitted, discontinuous sequence of actions is applied (Figure 1). Recently data will be collected from drill hole cores. These rock samples are analyzed in a laboratory. Based on those analyses a resource model is created whereby unknown data between drill holes is interpolated. This resource model is the basis for all mine planning actions including the selection of the mining method, extraction sequencing and the prediction of the expected performance. With the start of the production, real conditions (concentrations of elements, hardness, stability, etc.) can be observed and measured. As the production process is running accordingly to the above described mine plan, the verification of the initial assumptions happens at the earliest after processing of the extracted material. Even if deviations between the predicted and the actual performance are now recognized, the execution of corrective actions is not possible anymore."

Jan 1, 2016

By A. Garnier, K. Tremblay-Bouliane, B. Gaillet, S. Moineau, D. Tremblay

"A heptapeptide library displayed on M13 bacteriophages (phages) was screened to identify peptide sequences able to selectively bind to gold, chalcopyrite, sphalerite, pyrite, and silica ores, and to evaluate phage potential as bioflotation reagents. Many peptide sequences were isolated through biopanning and differed from known sequences. Adsorption isotherms were determined and a receptor/ligand interaction model was identified and used to compare affinity of peptide sequences toward ores. Some phage sequences have slightly lower affinity to sphalerite than other sulphides. Adsorption was higher on sulphides than on silica. Induction time measurements suggested filamentous M13 phages lower hydrophobicity of the ore surface.RÉSUMÉ Une librairie d’heptapeptides présentés sur des bactériophages M13 (phages) a été criblée afin d’identifier les séquences peptidiques affinitaires à des minerais d’or, de chalcopyrite, de sphalérite, de pyrite et de silice et d’évaluer le potentiel de ces phages en tant que de bio-réactifs de flottation. De nombreuses séquences peptidiques ont été isolées par bio-criblage et différenciées d’autres séquences connues. Des isothermes d’adsorption ont été déterminées et un modèle d’interaction récepteur–ligand a été identifié et utilisé pour comparer l’affinité des séquences peptidiques par rapport aux minerais. Certaines séquences de phages possèdent une affinité légèrement inférieure pour la sphalérite comparativement aux autres sulfures. L’adsorption sur les sulfures était plus élevée que sur la silice. Des mesures de temps d’induction suggèrent que les phages filamenteux M13 diminuent l’hydrophobicité de la surface des minerais."

Jan 1, 2016