Search Documents

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By A. O. Gapchich, T. N. Matveeva, N. K. Gromova

"Tin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. The aim of the work is an experimental study of the modification of the surface of sulfide minerals and cassiterite by stable metal-collector complexes to increase extraction of fine tin, silver, copper and other metals from complex tin ores. Triamide cyanuric acid (TCA) was studied as a thin silver flotation modifier. Thermophilic polymer with a functional group of phenylphosphine TMPPh was used as a selective flocculant. For experimental studies of the physical and chemical effects of collecting agents on the surface of minerals the following analytical techniques were used - the analytical scanning electron emission ASEM (LEO 1420VP INCA OXFORD ENERGY 350) and laser (KEYENCE VK-9700) microscopy, measurements of electrode potentials of mineral anthills by potentiometric titration, monomineral and pulp flotation. New data on formation of the adsorbed layer of DBDTC on the surface of chalcopyrite, galena and arsenopyrite were obtained, and the dimensions of the reagent films and the strength of their adsorption. The indiscriminateness of cassiterite to DBDTC ensures its selective separation into a chamber product during the flotation of sulfides. It is shown, that modification of the sulfide surface by stable complexes Me-DBDTC and Ag-TCA-TMPPh will increase the recovery of non-ferrous metals and silver into a collective sulfide concentrate and will provide a high-quality tin concentrate for flotation of tin sulfide ores.The studies were perfomed with the aid of the Russian Science Foundation (Project No. 17-17-01292).INTRODUCTIONTin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. In this regard, it seems advisable to use new varieties of flotation reagents in order to increase extraction of finely dispersed tin, silver, copper and other non-ferrous and precious metals from multi-metal tin ores (Bocharov and Ignatkina, 2007; Khanchuk etal., 2012; Wu and Zhu, 2006; Yusupov etal., 2016)."

Jan 1, 2018

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption, SEC) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness as a way to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e. less energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant, if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant.

Jan 1, 2018

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018

By J. Awmack, M. A. Tomlinson, P. J. Lind

"Peñasquito is a complex polymetallic deposit containing gold, silver, lead, zinc, and copper and is one of the largest producers of gold in Mexico. Mining activity is currently transitioning to a second open pit, Chile Colorado, which will be mined concurrently with the existing open pit, Peñasco. The ore bodies are located within diatreme pipes and into the surrounding sediment formation. In the coming years, mining will be carried out in more sedimentary zones, which are significantly higher in organic carbon content. Organic carbon in the feed influences both flotation and leaching operations. Several changes are being implemented to the Peñasquito flowsheet to mitigate the effects of increased organic carbon in the plant feed. These include the use of alternate reagent schemes, construction of a carbon pre-flotation circuit, implementation of a pre-leach flotation circuit ahead of pyrite leach, and evaluation of a tertiary process for separation of carbon and precious metal minerals.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas in the Mazapil municipality (Figure 1). Peñasquito has been in operation since 2009, with mining carried out by open-pit methods. Oxide ore has been processed in a heap leach facility and sulfide ore is treated in the sulfide processing plant. The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 465,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead in lead concentrate, and 263 million lb of contained zinc in zinc concentrate (Goldcorp Inc., 2017). To recover more of the contained gold and silver and to mitigate the impact of increasing organic carbon content in the ore, a number of significant changes are being made to the operation."

Jan 1, 2018

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition. This article is devoted to the promotion of the concept of mineral processing in modern realities of the deficit of high–grade ores and increase in their demand. Normative and methodical documentation for specific types analysis with the definition of the field of application are presented in this paper. . For example, the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore field were tested. The development of mineralogical methods and testing of specific raw materials are shown. The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field.INTRODUCTION A highly intense production of many types of mineral deposits results in gradual depletion and of mining-geological and mining-technical conditions of various ore reserves ?. Relatively easily accessible and rich deposits are getting depleted in the first place, and it is necessary to involve low grade and refractory ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral deposits, creation of scientific and methodological pre-requisites for solving the problem of rational development of mineral deposits, maximum extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and ores.The article is aimed at updating tasks that should be addressed within the applied mineralogical research: – forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of properties ore, – interactive monitoring of these indicators by mineralogical and analytical methods;"

Jan 1, 2018

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By E. V. Bratygin, S. P. Elnikova

"In the article carrying out technique of experiments for estimation of power efficiency of process of crushing in cone crushers «in a layer». The conformity of the granulometric characteristics of the crushed products obtained as a result of the tests, the theoretical equations for the size characteristics, and the choice of the optimal equation for the prediction of the granulometric characteristics of the final products obtained by crushing ""in a layer"". Optimization of granulometric composition of power of crushers working ""in a layer"" is carried out with the purpose of reduction of the electric power consumption at reception of a product of required quality. As a result of the experiments, dependencies are obtained, the relevance and applicability of the crushing process ""in the layer"" for obtaining crushed stone of improved quality is proved. INTRODUCTION A number of equations have been proposed for calculating the breakage energy. These include equations by Kirpichev and Kick, Rittinger and Bond (Bogdanov, Olevsky, 1982). Another equation for calculating the specific breakage work in breakage by impact and in stratum was proposed by Devyatkin (Boiko, 2003). In these equations, the breakage energy is proportional to the particle size raised to some power. In the equation proposed by Devyatkin, the ore piece thickness or the feed average diameter is used. The relationship between energy and breakage can be expressed as an equation (Lynch, 1981; Tikhonov, no. 3, 2008) where k is a coefficient characterizing the energy parameter depending on the strength of the feed, l is size in microns. The Rittinger formula is obtained for n = 2, the Kirpichev-Kick formula for n = 1, the Bond formula for n = 1.5. For n = 3 or higher, the equation describes fine and ultrafine grinding. R. Hookey proposed a formula (Lynch, 1981, Tikhonov, no. 3, 2008), where the size exponent n is substituted by a size function In all of the above equations, a single value of the feed and product size is used; for example, in the Bond equation, size is defined as the particle size of the 20% oversize (P80 and F80). However, a single size value can represent multiple distributions, making that the Bond method inappropriate for determining the size (Lynch, 1981). Describing an equation for estimating the grinding energy will allow to design the electric drive and ore preparation circuit for the given breakage method."

Jan 1, 2018

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

"This research aims at improving the beneficiation of coals and minerals in fine and ultrafine size fractions. A widely used method for upgrading fine and ultrafine particles is froth flotation, which is generally classified into mechanical flotation and column flotation. The present work is focussed on column flotation. A flotation column equipped with a conventional bubble diffuser/sparger was used with oscillatory air supply generated using a fast-switching solenoid valve. The flotation tests were carried out for coal particles and mineral particles, respectively, and a comparison in flotation performance was made between oscillatory air supply and steady air supply. It was found that use of oscillatory air supply with a proper valve switching frequency and on/off time ratio to replace steady air supply could lead to increased recovery of coals or minerals by more than 14 percentage points and substantial reagent cost savings. The improved flotation performance was attributed to enhanced gas dispersion and flow conditions. This research offers a simple new approach to improving the beneficiation of fine coals and minerals with using flotation columns.INTRODUCTIONFroth flotation has been widely used for the separation and concentration of fine coals and minerals by exploiting the difference in their affinity to air bubbles in aqueous medium. Froth flotation is an effective method for beneficiation of coal and mineral particles in a certain size range. It remains difficult to upgrade ultrafine mineral particles. One of the reasons for the ineffective flotation of fine particles is the low probability of bubble-particle collision in the collection zone (i.e., the pulp zone). According to Reay and Ratcliff (1973) and Yoon and Luttrell (1989), the probability of collision is significantly affected by bubble size and particle size, and the collection zone recovery can be increased by decreasing the bubble size."

Jan 1, 2018

By Rick Deschamps, Brian Barkauskas, Aled Hughes, Abigail Stein

In central Washington, six miles south of the small town of Vantage, the flow of the Columbia River is harnessed by the Wanapum Dam which is part of the Priest Rapids Hydroelectric Project owned and operated by Grant County Public Utility District (GCPUD). Extending more than 8,300-feet from bank to bank, the dam includes left and right earth embankments, left and right concrete gravity sections and a 10-unit powerhouse. Adjacent to the right embankment is a concrete gravity spillway featuring radial gates measuring 50-feet-wide and nearly 70-feet-high. In the early 1960’s when Wanapum Dam was built, these seven-story spillway gates were the highest in the world. In late February 2014, 50-years into its service life, during a routine maintenance inspection, observant workers noticed a slight misalignment in the roadway deck curbs and handrails located on top of the spillway. Further survey and inspection efforts uncovered a 65-foot-long by two- inch-wide crack that spanned the full length of Monolith 4. On discovering the extent of the damage, GCPUD initiated immediate drawdown of the reservoir to relieve pressure on the spillway monoliths. Wanapum Reservoir and the areas directly downstream of the dam were immediately closed, boat ramps and inlets were left completely dry, campsites were closed and boating activity was banned on the lake until further investigations and remedial procedures were in place and completed. An extensive root cause analysis ultimately led to the conclusion that errors in the initial design calculations and late changes to the final spillway design led to a condition that generated tensile stresses in the concrete at the upstream face, which over a period of 50-years resulted in the formation of a crack along a horizontal lift joint located about 85-feet below normal pool elevation. Further analysis showed that, although visible distress was found at Monolith 4, there was nothing preventing this issue from happening at other locations along the dam spillway. Although no visible cracking was found in the other monoliths, repair procedures for Monolith 4 would have to be replicated at the remaining monoliths.

Jan 1, 2018

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

By E. Keskinkilic

"Electrical steels are used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. These properties are attributed to the presence of a significant amount of silicon in the steel composition. Silicon steels are mainly grouped into two categories: grain-oriented (GO) and non-grain-oriented (NGO). The Si content of silicon steels is generally between about 0.50% and 6.5%. Therefore, silicon steels are further classified as low-, medium-, and high- Si steels. In this paper, liquid steel processing practices for certain silicon steel grades are outlined by considering a steelmaking company that integrates a basic oxygen furnace (BOF), a ladle furnace (LF), and an RHtype degassing unit (RH). Possible problems are identified, suggestions are discussed, and conclusions are drawn on the basis of real plant data. IntroductionSilicon steels are widely used in motors, power generators, and transformers for electrical applications owing to their superior magnetic properties. They are mainly grouped into grain-oriented (GO) and non-grain-oriented (NGO) silicon steel grades. However, the differences in the properties and thermomechanical production of GO and NGO grades are outside the scope of this paper. In this study, liquid steel processing of certain silicon steels will be discussed. In the integrated iron and steelmaking process, converters are the primary steelmaking units that are used mainly for decarburization and removal of phosphorus, and for obtaining liquid steel with a specific chemical composition and suitable temperature for secondary steelmaking operations. Ladle furnaces are a type of ladle metallurgy station consisting of electrical and/or chemical heating facilities for adjusting the liquid steel temperature during alloying. Various types of vacuum units are used for decarburization and removal of nitrogen, hydrogen, and sulphur, depending on the metallurgical conditions of the vacuum units. In this study, an actual steel-production company is considered in which the primary steelmaking operation uses a basic oxygen furnace (BOF) converter with N2/Ar bottom blowing, and the secondary steelmaking operations involve (1) a ladle furnace (LF) heated by three graphite electrodes and equipped with Ar and N2 top/bottom mixing facilities, and (2) an RHtype (circulation) vacuum degassing unit equipped with a top-blowing attachment for oxygen blowing and an Ar-purging system from an up-leg snorkel."

Jan 1, 2018

By C. A. Vining, J. R. Nopola

"Evaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. Evaporites are subject to continual creep and no amount of ground support can successfully arrest this process. Common ground-support techniques that are useful for most rock types may reduce the effective life of bolts in evaporite mines and can create unseen hazards. A different approach to ground support must be applied to provide long-term support in areas where high creep rates are present. The goal of effective ground-support designs in these situations is not to contain the rock and prevent it from moving; rather, the ground-support design must be able to move along with the rock and contain any fully detached slabs until additional remediation measures can be undertaken. The most appropriate ground-support designs will consider both the expected movement of the rock and the duration that the area needs to remain accessible.INTRODUCTIONEvaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. The factors that must be considered in design stem from the deformation behavior of salt, which can fail in a brittle manner, akin to most rocks, but can also deform in a slow, ductile manner, resembling the stretching and elongation of steel. The deformation behavior of salt has been well established in technical circles where it has been studied for decades (Hardy and Langer, 1984). Much of the research in salt mechanics is related to repository science, specifically at the Waste Isolation Pilot Plant (WIPP) in southwest New Mexico. RESPEC has been continually involved in the WIPP from the initial design considerations (Gnirk, Grams, and Zeller, 1977) to the current day (Keffeler, 2016) and has been able to leverage cutting-edge research of salt mechanics into practical solutions for mining operators. While a detailed description of salt mechanics is not provided in this document, Fossum and Fredrich (2002) include a fine overview of salt mechanics. The following list paraphrases their chapter on basic facts about salt to provide some context for the reader unfamiliar with salt mechanics:"

Jan 1, 2018

By Y. Y. Li, T. T. Yang, R. X. Zhou, Z. H. Shen

"Wetting theory is one of the basic theories of flotation. The effects of concentrations, carbon chain length and pH values of saturated fatty acid collectors (lauric acid, myristic acid, palmitic acid and stearic acid) on the surface wettability of collophanite and dolomite were investigated by measuring the contact angle with dynamic captive-bubble technique and calculating adhesion work of bubble-mineral. The results show that the contact angles both of collophanite and dolomite are higher with enhancement of hydrophobicity when pH value of 5~9. The contact angles both of collophanite and dolomite are reduced with improvement of surface hydrophilicity. When strong acid pH value of 2~4 or strong alkaline pH value of 10~13. The reasons for this are that the fatty acids mainly exist with insoluble RCOOH molecules in strong acid condition, and competitive adsorption of OH- and RCOO- in the mineral surface is formed in strong alkaline condition. With the increase of the collector concentration, the contact angles of the collophanite and the dolomite all first increase then decrease. The formation of hydrophilic micelles results in the decreasing of contact angles and enhancement of surface hydrophilicity opposite when the collector concentration exceeds CMC. The contact angles of the collophanite and dolomite and the WSG of the bubble adhesion increase, the hydrophobicity enhance with the increasing of carbon chains of saturated fatty acid from 12 to 18. The variation tendency for the adsorption quantity of collectors and floatability of collophanite and dolomite are in line with the change trend of contact angle basically. It shows that the wettability of solid-liquid-gas interface can be well characterized by the dynamic captive-bubble technique.INTRODUCTIONPhosphorite resources are the main raw material for producing phosphate fertilizer and producing phosphoric acid (Cao et al.,2005), which is an important strategic mineral resource. The useful minerals in calcareous-magnesium phosphate ore are collophanite, and the main gangue minerals are dolomite (SISH et al.,2003). The lattice ions of the phosphorite and dolomite are both Ca2+, their similar surface properties and similar floatability are the main reason for the flotation of calcareous-magnesium phosphate ore difficultly (Fang et al.,2011). Usually, fatty acid collectors are used for the flotation of calcareous-magnesium phosphate ore under acidic conditions by reversing flotation method to remove dolomite (ABOUZEID et al.,2009), or direct flotation is used to gather collophanite in the alkaline conditions (Gong et al.,2017). The flotation behavior of collophanite and dolomite affects the indexes of concentrate and flotation efficiency directly. Therefore, it is necessary to study the action mechanism and the flotation method of the collector with the phosphate rock and dolomite respectively (Moudgil et al.,1988; Hanna, et al.,1990)."

Jan 1, 2018

By Jun Xiao, Jianwen Yang, Yanhong Dong, Daixiong Chen

"MANGOTE Surface oxidizied mine is a gold-bearing deposit in Congo's Mai-Ndombe Province. In the past decades, the ore has been exploited in a crude way by local farmers, which directly causes the severe processing difficulty and lack of economy of cyanide leaching. Hunan Research Institute for Non-ferrous metals (HRIM) is currently investigating options to recover gold through understanding the mineralogical characteristics of MANGOTE surface oxidized ore. Chemical analysis , X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANing electron microscopy (QEMSCAN ) were conducted on samples from mine site. The bulk analysis results showed that gold separation of gold from gangue minerals was feasible after grinding the ore samples to 86.53% -74µm and adjusting the pulp specific weight at 100g/L, and gravity separation was conducted with using spiral chute after grading of fine particles. The research results highlight relationship between mineralogical characteristics of abandoned ore and economy of comprehensive utilization that might be directive experience to similar cases. INTRODUCTION The occurrence state of gold in natural gold minerals determines the basic recovery and recovery effect of gold(Komnitsas, C., & Pooley, F. D. 1989). The occurrence of gold in the ore refers to the form of gold in the ore.Generally the existing state of gold can be divided into four major categories according to the viewpoint of the dispersion system: independent minerals and gold, a coarse dispersed system;colloidal gold, a colloidal dispersion; solid solution gold, is atomic ion dispersion; adsorptive gold, according to the adsorbed particle is the micelle or ion, respectively is a colloidal dispersion or ion dispersion(Mao, S. D., & Yang, R. S. 2009; Liu, J. J. et al. 2007; Horisberger, M., & Rosset, J. 1977; Li, Y., & Audétat, A. 2013).With the increasing technology of comprehensive utilization of resources,varied plants can now process different gold ores with various occurrence states(Neesse, T. 2014; 7. Ogundare. et al.2014)."

Jan 1, 2018

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018