Search Documents

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By R. Khanna, M. Dubikova

A variety of carbonaceous reducing materials are being used for the production of ferroalloys. Reductant materials include not just carbons such as coke, coal, char but also bio-carbons in form of charcoal produced from different types of wood. This paper discusses critical properties and reactions of carbonaceous materials and their significance in dictating reductant performance. Main considerations include among others, gasification of reductant, dissolution of carbon into molten metal, and direct reduction of slag by solid carbon. These are discussed in relation to material properties such as structural order, mineral matter content, composition, physical characteristics etc. A brief review of both conventional and novel approaches towards characterisation of carbonaceous materials has been included. Due to complexity and heterogeneity of carbonaceous reducing materials and a wide range of process requirements, the selection of the most appropriate reducing agent will depend on a number of considerations such as the availability of raw material and associated costs, product and process requirements and environmental aspects of waste gas emissions.

Jan 1, 2004

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004

By John Jordan, Tesarik, Steven J. Knoll, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By E. Henry, C. Mayer, H. Rott

Hangingwall deformation monitoring at Kiruna mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening toward the town of Kiruna. In the quest for more effective monitoring techniques, LKAB decided to evaluate the ability of satellite-borne synthetic aperture radar (SAR) interferometry to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the mining industry. This paper describes the basic principles of SAR interferometry and describes how subsidence is monitored at Kiruna mine. The encouraging results are discussed as well as the benefits (continuous deformation mapping, low cost, fast, etc.) and limitations (sensitivity to snow and vegetation cover) of the technique.

Jan 1, 2004

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By M. C. Bhulose

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The purpose of this project was to identify constraints that could occur in the current sub-decline shaft at Turffontein Shaft should an increase in production take place. Particular attention was to be paid to the transportation of men and materials and to the broken rock and ventilation capacity of the shaft. This project is an in-depth evaluation of the logistic capacity of the sub-decline system at Turffontein Shaft in order to determine by how much production can be increased in this area to replace tonnages from the vertical shaft area, where ore reserves are rapidly becoming depleted.

Jan 1, 2004

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By M. A. Berdine, C. N. Thompson, D. Brock

The raise bore method of shaft construction has been success-fully used in the mining and construction industries for over thirty years. In the mid 1990’s, Twentymile Coal Company (“TCC”), now affiliated with RAG American Coal Company, used this method for a moderately deep small diameter shaft and the raise bore and slash method for a shallow larger diameter shaft. In late 2001, TCC contracted to raise bore a 431-meter deep, 6.2-meter diameter shaft. During the raise bore and shaft lining processes, regional horizontal stress fields resulted in extensive elliptical caving beyond the original design diameter. This paper discusses the engineering approaches and procedures used to safely complete construction of the raise bore shaft.

Jan 1, 2004

By S. Ando

The fatigue crack growth behavior of magnesium single crystal has been investigated, CT (compact tension) type specimens with different notch orientations were prepared. In the case of notch plane and direction are (1-210) and [10-10], fatigue crack propagates parallel to notch, From TEM observation, it is found that pyramial slips occures at the crack tip. When notch is normal to basal plane, a fatigue crack propagates [0001] and parallel to basal plane depending on stress intensity factor range, In the case of notch parallel to basal plane, a fatigue crack propagates through straight route with some {10-12} twin, Fatigue crack growth rate, da/dN of A- and B- specimen is lower than F-specimen with crack parallel to basal plane.

Jan 1, 2004

By R. Falcon, P. den Hoed, A. Luckos, R. Erasmus, V. du Cann, D. Comins

Carbon as a reductant, additive or filler is an essential element in the processing of metallic ores and the manufacture of iron and steel in the metallurgical industry. In most cases, the element carbon is derived from coal and its carbon derivatives. The properties of carbon required for the different processes in each metallurgical sector vary significantly and, for this reason, matching the correct carbon product for each specific process has become an important if not vital function in all sectors of this industry. This selection process, however, has become increasingly difficult. In many cases, the substitution of new products, despite being similar in all relevant chemical specification characteristics to previous products, has resulted in different performance properties relative to that expected. Under these circumstances, the prediction of performance of unknown carbon products has become fraught with difficulties unprecedented in the past. In order to initiate an investigation into addressing these issues, a test case was selected for indepth study the results of which are reported in this paper. The case concerned the use of a specific carbon feed in a conventional submerged arc furnace which gave rise to an unprecedented amount of unreacted or only partially consumed residue trapped in the frozen slag on the refractory walls of the furnace. During the course of these investigations, different advanced analytical technologies were employed including, inter alia, Raman spectroscopy, surface dimensional tests, organic petrology and various thermal reactivity factors. All results have been integrated into a multidisciplinary assessment presented in summary in this paper. Based on the above, and previous experience, the concept of an all-embracing 3-D coal-carbon ?framework? is briefly introduced. This approach has succeeded in obtaining greater depth of knowledge and a better understanding of the issues at stake with specific reference to the organic composition, structure, texture, internal surface area and consequent reactivity of the carbon materials concerned. In consequence, it would now appear that various properties of relevance to the metallurgical industry may be predicted with greater precision than has hitherto fore been possible.

Jan 1, 2004

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context in which they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage such as nuclear power generation where international cooperationis eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit its mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2004

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By I. A. Minaev

The conditions of a stability of metallurgical films on a surface of solid on the basis of classical regularities of a thermodynamics are considered. For specific conditions of metallurgical processes the basic equations relevant to non-metallic inclusions (product of steel killing) migration and transfer through the interface boundary of metal-slag are obtained. The basic criteria equations of conditions of stability of metallurgical dispersed systems are developed in view of films formation. The probable thermodynamics reason of wetting due to formation of stable films are discussed. The experimental measurement of thin and thick films elastic resistance for metallurgical systems are carried out and the results are discussed. The presence of a wetting thick film increases stability of dispersed systems (facilitates an inverse implication of non-metallic inclusion in a melt) due to a barrier effect of wetting films. The quantitative evaluations of non-metal inclusion stability for steel in contact with any metallurgical slag are carried out. The results are in accordance with technological experience. Keywords: Inclusion removal, Film thermodynamic, Slag-metal dispers system

Jan 1, 2004

By M. Pearson, L. Zunti

Pressure vessels in hydrometallurgy and many chemical process industries throughout the world require the use of specific lining systems to protect the parent vessel materials from corrosion and/or abrasion. Typically, these lining systems are required for processes that are corrosive and operate at elevated temperatures. Two basic lining system types arc: 1) refractory linings in conjunction with an impervious corrosion resistant membrane, and 2) metal-clad vessels consisting of titanium or other corrosion resistant metal bonded to a carbon steel shell. Operating conditions play a key role in selecting the type of lining system to be utilized for a specific application. Lining systems in turn have an impact on the process vessel size, which ultimately affects the capital cost of the vessel. The capital costs for each type of lining system must be considered for each application, as well as maintenance concerns, quality control, and delivery. It is clear that operating conditions play a key role in the final selection of lining systems utilized for specific projects based on initial capital cost, life-cycle maintenance costs, and overall service life. This paper will examine the fundamentals of each lining system, their inherent technical strengths and weaknesses, and present relative cost comparisons for each lining system as they apply to specific operating conditions and vessel sizes.

Jan 1, 2004

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

As the mining industry looks to new technologies for a safe work environment and increased production rates, so should emergency response teams when dealing with organisational incidents. Implementation of technology has transformed the nature of incidents within the international mining community with lower frequency, high impact events replacing high frequency, low impact incidents of the past. In turn the approach to mines rescue response and preparation has naturally diversified. New rescue technologies when applied effectively can only further advance preparation and the response of mine rescues teams. This paper discusses some of the changes associated with mines rescue as the industry embraces technology. It highlights some recent rescue responses and their approach and gives examples of some of the new technologies being used for improved mines rescue.

Jan 1, 2004