Search Documents

By P J. Fourie, J R. Walklate

Gravity separation techniques have been in use in the mineral sands industry for decades; from the Reichert cone to Wilfley tables, Wright sluices and the Kelsey Jig, all attempting that elusive perfect gravity separation. Just as the gravity separation industry evolved, Richards Bay Minerals also evolved in their use and approach to gravity separation. This paper discusses the history of gravity separation at Richards Bay Minerals and briefly comments on future developments. History Primary Concentration Richards Bay Mineral?s (RBM) first mining concentrator and mineral separation plant commenced operation in 1977 to process ilmenite, rutile and zircon bearing dunal deposits along the northern Natal coast. The orebody contained a greater proportion of non-valuable magnetic heavy mineral in the SG range of 3 to 4 compared to West Australian and Florida USA deposits, making mineral separation more difficult(1). The deposit was mined using two dredges feeding a floating 2000 tph concentrator. Concentrator feed was screened and fed to two four-stage circuits consisting of primary, scavenger, cleaner and recleaner Reichert cones [see Figure 1]. The primary units were fed at a rate of 80 tph and a density of 60% solids by weight.

Jan 1, 2006

By W. Gan

The interactions between bitumen and quartz sands in aqueous solutions were studied with the objective of recovering residual bitumen from Athabasca oil sands froth treatment tailings. It was observed that the presence of various multivalent metal cation (Fe3-, Fe2+, Mg2+,Ca2+, etc.) increased the mutual coagulation between quartz particles and oil or bitumen droplets within certain pH ranges. While the increased coagulation was detrimental to the recovery of the bitumen since it lowered the degree of bitumen liberation from sands, this effect could be reduced or eliminated by the addition of organic chemicals such as citric acid, oxalic acid and EDTA. Among these organic chemicals, citric acid was found particularly effective even at very low concentration.

Jan 1, 2006

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006

By Mike Fabius

The Lakehead Region Conservation Authority is responsible for slopes along the Kaministiquia River, one of the largest tributaries to Lake Superior in Canada. After arresting toe erosion for a mile of riverbank, the remainder of the slope required stabilization to stop further crest regression and to protect the houses, street and services at the top. Stabilization of the 100 ft. high slope was tendered as design-build with a target safety factor of 1.3 and a design life of 75 years. The successful bid was a system of 1.4 inch diameter soil nails up to 40 feet long, installed perpendicular to the slope on a 3 to 5 foot grid. The conventional shotcrete facing was replaced with a ?green? biotechnical facing and special transverse plate heads on the nails. The key to keeping costs low proved to be installation with light equipment working on the slope, and driving the nails without drilling or grouting. Rather than tension, the design was based on bending in the nails, similar to a laterally loaded flexible pile. The paper describes the design and installation of this innovative system. The design is discussed in terms of soil properties, nail resistance as it varies with depth, failure modes, corrosion protection, root design and nail head design. Construction challenges are discussed. The system is compared to an adjacent anchored soldier pile wall built along the same slope 20 years ago. Post construction monitoring results confirm predicted performance.

Jan 1, 2006

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By Glen Mc Gavigan

The roof of the Sishen cave is being mined in order to exploit 6.8Mt of high grade ore. The cavity is filled with quartzite backfill in order to support the roof in the event of collapse. The cave dips at approximately 37o, is 260m along dip and 70m along strike and has a total volume of 261,391m3. GPS and optical monitoring techniques were attempted to detect subsidence but proved to be impractical. The GroundProbe Slope Stability Radar (SSR) uses differential interferometry to measure sub millimetre movement in a rock face. The SSR was applied in a non production situation and detected subsidences of 38mm/day before visual signs of instability were detected. The rate of deformation detected was slowing as a result of the roof coming to rest on underlying backfill. Monitoring during production drilling detected a sudden subsidence of 18.6mm/hour which resulted in the evacuation of personnel from the area. Further inspection of data showed that the rate of deformation was slowing and production was allowed to continue without further incident. The SSR has helped dispel the fears of workers and has proven that subsidence can be accurately measured and delineated with the SSR.

Jan 1, 2006

By J. E. McGill

The junior and small-scale mining sectors in South Africa play an important role in the livelihoods of numerous communities. Mining presents an opportunity, in the post-1994 democratic era, for many individuals to obtain access to much required empowerment and socio-economic development. These sectors are, however, not without numerous characteristics that pose problems for operators, legislators, and other role-players. Mining is inherently risky, with operators experiencing frequent difficulties and challenges throughout the life of mine. Opportunity exists, and needs to be enhanced, for junior and small-scale prospects and operations to include technical risk assessment techniques in documentation presented in search for funding, and in optimizing monthly planning and longer-term functioning. The focus here is to explore how the risk management cycle may currently be applied to a mineral resource suitable for exploitation by the junior and small-scale mining sectors. No management process can create additional value in the ground, but various available mechanisms can go a long way to quantifying the inherent risk that exists, highlighting the need to manage the risks and hopefully allowing the entrepreneur access to the intrinsic opportunities of the emerging mining sector in South Africa.

Jan 1, 2006

By Grant Loveday, Vincent Dieudonné, Andrew Jonkers

Bateman Minerals & Metals supplies the APIC Technologies which include the under-bed air-pulsed APIC jig and related technologies such as the JigScan controller and advanced mathematical models of the jig process. Bateman have developed a methodology for predicting process performance for jigs from simplified testing and modelling, based on batch equipment matched to industrial designs. Batch tests conducted on laboratory scale air-pulsed jigs can process small batches of material, such as those obtained from drill core samples. The novelty comes from using an advanced jig process model, ASTRAD, to link the results of batch and continuous jigs. The batch jig presented as a novelty in this paper has been designed to be hydraulically equivalent to the full-scale APIC Jig, allowing the generation of equivalent pulse shapes and using JigScan controller. Lump and fine ferrous ore material have been separated in this unit and any feed >1mm can be tested and extracted. The global test procedure and further modelling focus on the stratification of material, with emphasis on key aspects such as pulse shape, feed characteristics and residence time. The splitting of rejects from concentrates is itself more difficult to reproduce in batch jigging, however the ASTRAD model includes a separation imperfection module, and the APIC Technologies have extraction systems adapted to each type of material. Air pulsed batch jigs are available in several locations and are relocatable. They have been used to treat samples from Australia, South Africa and India as part of studies into ore processing using jigs. Each test layer is available for various physical testing procedures (density and chemical analyses). Test-work is performed on a case by case basis, and analysed using an advanced model ?now available over the internet. Some fundamentals of air-pulsed jigging are recapped along with some of the features of APIC jigs. The process of designing a ?hydraulically equivalent? batch jig test is then described. Some results from jigging tests are presented plus the results of the ASTRAD advanced jig model, which was first developed at the JKMRC with ferrous ores and coal and is now being supported and further developed and utilised by Bateman.

Jan 1, 2006

By A. P. Paiva

The solvent extraction properties exhibited by some /V,N'-tetrasubstituted malonamides to efficiently and selectively recover iron(III) from concentrated chloride leaching solutions can be found in the recent literature. The iron(III) extractive chemistry exhibited by some of these derivatives is revisited, in order to compare their chemistry with that shown by a few of the new malonamide compounds. The generally good extraction efficiency towards Fe(III), from >4 M hydrochloric acid solutions, and the relative ease of Fe(III) stripping by distilled water are remarkable findings that are confirmed for the malonamide derivatives described in this work. Furthermore, additional data regarding their selectivity towards Fe(III) extraction over several base metal ions and their behavior when subjected to successive Fe(III) extraction-stripping tests are also presented and discussed.

Jan 1, 2006

By M. J. Latva-Kokko

This paper describes the behaviour of iron and the methods used for iron control in the nickel matte leaching process. OMG Harjavalta Nickel Oy processes approximately 10 000 t/y of iron, which enters the process with the nickel matte raw material. Iron dissolves and precipitates in several different stages of the leaching process. Compounds like ferric hydroxide, parabutlerite, goethite, hematite and jarosite are found. Iron removal is done within the leaching process, and this means that the dissolution of nickel sets the limiting conditions for iron precipitation. A leach residue consisting mainly of the iron precipitates is neutralized and stacked in the waste pond. When iron is precipitated from concentrated nickel sulphate solution, some nickel is lost by co-precipitation. Recent studies have shown that Ni-Fe ratios less than 1%, attributed to co-precipitation, can be obtained with jarosite precipitates, compared to 2-3% ratios typically found with hematite precipitates. Iron can be precipitated as jarosite under the optimal nickel leaching conditions by adding ammonium sulphate to the feed slurry of the autoclave.

Jan 1, 2006

By S. Sundararajan, J. Brousseau, P. Bocher, M. Galopin, N. Barka

This research is committed to the prediction of the hardness profile produced by induction heating, using a computer-modeling software. The paper presents the simulation of the induction hardening process to analyse the sensitivity of the induction parameters on the hardness profile of a low alloy steel specimen. The developed numerical model includes the coupling effect between electromagnetic and thermal fields, and takes into account the non linear behaviour of the material properties. The study applies an enlightened experimentation method to build the feasible domain of the process and to achieve predictive empirical modeling. The ultimate goal is to replace the trial and error method that is usually used for the development of new parts, by costless experiments with the numerical model. Further development of this approach will lead to the computation of the residual stresses and finally to the assessment of the mechanical properties of the part. The end result will be the ability to shorten the development time and to improve the quality of the hardened part.

Jan 1, 2006

By Rachel De Lucas

Current methods of hydrogen storage are an impediment to the transition of our energy infrastructure from a hydrocarbon to a hydrogen base. The transportation, handling, and storage costs of hydrogen gas account for a majority of its selling price. Magnesium hydride slurry is a safe, environmentally friendly alternative for hydrogen storage. If this form of storage is to be adopted on a large scale, a cost-effective method for recycling the enormous amounts of magnesium hydroxide byproduct must be identified. The solid oxide membrane (SOM) process can be used to recycle the magnesium hydroxide byproduct into magnesium metal, which can be reformed into magnesium hydride and reused for fuel storage. Conventional magnesium extraction/recycling technologies require a great deal of energy and create byproducts that are harmful to the environment and human health. The SOM process poses none of these detrimental effects and requires less energy and feed preparation. The economic viability of a facility that utilizes the solid oxide membrane process for the direct reduction of magnesium must be examined in more detail if industry is to consider it. Cost analysis data related to the commercial viability of a scale-up will be compared to two standard industrial processes: current magnesium production techniques including electrolytic and metallo-thermic processes. We have shown in our cost comparison that the SOM process is cheaper than these traditional techniques and that it is also comparable to aluminum's Hall-Héroult process in cost but with none of the environmentally harmful byproducts.

Jan 1, 2006

By A. A. Sizikov, V. A. Sizikova

Key parameters to consider for any producer: bring down production cost and lead time; Lean production as a tool to achieve maximum efficiency; How to implement lean principles: discontinuous vs. continuous production (aluminum industry); About RUSAL: global top-three aluminum producer; Lean tools at use at RUSAL's production facilities; Pull system, Standardization of work, Just in time, Continuous improvement, Customer-Supplier relations, etc.

Jan 1, 2006

By A G. L Pratt, J R. Grant

Mining companies face the ongoing challenge of sustaining and growing production. This paper outlines business investment concepts to grow reliable returns on investment from a portfolio of choices by:improved visualisation, diagnosis and tune up of the investment pipeline (pipeline management); good corporate decision making (governance) to select the right project mix, risks and sequence; and delivery strategies to enhance and reliably execute projects.

Jan 1, 2006

By Bernard Bonnetot

The potentialities of hydrogen storage using borohydrides are presented and discussed especially in regard to the recoverable hydrogen amount and to the recovery conditions. A rapid analysis of storage possibilities is proposed taking in account the two main ways for hydrogen evolution: the dehydrogenation obtained using thermal decomposition of borohydrides or the hydrolysis of solid or dissolved borohydrides. The recoverable hydrogen is related to the dehydrogenation conditions and the real hydrogen useful percentage is determined for each case of use. The high temperatures required for dehydrogenation, even using catalyzed borohydrides, lead to poor outlooks for this storage technique. The hydrolysis conditions fix the yield of the recovered hydrogen and rule the storage capacity of the dissolved borohydride, the "fuel".

Jan 1, 2006

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By K. Tada

A surface of a magnesium slab (hereinafter, referred to as Mg slab) or magnesium alloy slab (hereinafter, referred to as Mg alloy slab) becomes black with the use of conventional manufacturing methods. The methods also involve a danger that an explosion of the molten magnesium occurs through contact with cooling water. Thus, it has been impossible to produce a slab having a smooth surface. In the present method, a molten magnesium alloy is supplied into a mold, which is sheltered from the surroundings, from a pool in tundish, which is shielded from the surroundings. AZ31B slab formed in the mold is drawn horizontally out to the outside from an outlet of the mold by revolving of the pinch rolls. A cooling water is jetted at an acute angle onto the slab on the outer side of the mold outlet. Further, an inert gas is sprayed at the inner side of the mold outlet in order to seal in a gap between a free surface of the molten magnesium alloy and a sheltered board surrounding an upper surface of the mold. As a result, oxygen and droplets of the cooling water are prevented from running back to the mold side through the gap. AZ31B slab has a smooth surface condition and high quality without a gas porosity, a segregation or the like. Further, the slab has a size of a width of 100 to 120 mm, a thickness of 5 to 20 mm and a span of 10 m or more.

Jan 1, 2006

By Y Gu

The Mineral Liberation Analyser (MLA) employs the technologies of scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX). The use of backscattered electron images to define phase boundaries produces very high resolution image analysis and subsequently detailed and accurate particle images and data output. The mineralogy, elemental deportment, grain size, liberation characteristics and mineral associations of a large number of samples can be described. The MLA uses a comprehensive set of analysis methods to meet a wide range of applications. The data from ore characteristion projects completed during feasibility studies are important aids for effective plant design. The MLA can be used to establish variation in the mineralogy of an orebody, identify and quantify the deportment of deleterious elements, and provide valuable information to support comminution and flotation test work. In established plants the MLA data is an important component of plant survey work and monthly composite samples. Changes in feed characteristics and/or operating conditions can be monitored and solutions to any deterioration in recovery and grade performance found. The MLA has extensive applications in the minerals industry. Rare and precious metal samples can be accurately measured using high-resolution grey-scale images. Several new measurement techniques have been developed to perform rapid searches of a large number of samples to provide efficient and accurate analyses of fine-grain, low concentrate material. Quantifying the mineral variability in mineral sands operations is essential to maximising grades and recovery. The MLA produces particle-based data on density, mineralogy, size and shape and has developed measurement techniques to provide the elemental quantification required for the characterisation of these deposits. Nickel sulfide ores can be analysed to provide modal mineralogy, elemental deportment and liberation and locking data. The low-grade and variable nickel mineralogy of these deposits makes the use of quantitative mineralogy an essential component of maximising returns. Coarse particle measurements preserve the in situ textures of ores and support flotation and breakage test work for feasibility studies. The deportment of penalty and bonus elements can be quantified and the association and grain-size data can be used to identify potential separation issues.

Jan 1, 2006

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006