Search Documents

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010

By D. Kelley

Due to pricing volatility and lack of availability of metals, the use of non-metallic materials of construction in metal extraction and refining processes has increased significantly in recent years Even though costs and availability of metals has improved recently, these factors are not expected to continue into the future as metal supplies once again fall short of global demand. One of the most common non-metallic materials of construction used in metal extraction and refining processes today is Fiberglass- Reinforced Plastic (FRP). These processes often require materials of construction that can resist acids and high concentrations of acid chloride salts. As shown in Table 1, FRP based on epoxy vinyl ester resin has the same chemical resistance to acid and better resistance to acid chloride salts than alloy C-276 and is superior to 2205 stainless steel in both cases.

Jan 1, 2010

By J. Botha

There are many underground mining software tools available to plan and schedule the development of underground mines. A shortfall of these tools is the optimization of the underground equipment and strategy in order to maximize the development rate. This paper will illustrate how the SimMine® software was used to maximize underground development at Petra Diamonds' Cullinan Diamond Mine. It will also determine the effect of various development strategies and equipment capacities on the underground development rate and pinpoint potential bottlenecks in the mine development cycle.

Jan 1, 2010

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By Noel N. Moebs

This report summarizes a U.S. Bureau of Mines study on the application of geotechnology to identify and minimize ground control hazards in talc mining operations in northwest Georgia. The major ground control hazard is pillar sloughing attributed to the steeply dipping orientation of a pronounced foliation in the talc ore body. The sloughing problem, which gradually reduces the effective support area of a pillar through attrition, can be minimized by appropriate artificial support, as determined by a rock classification system, and by a more uniform pillar design. A boundary element model confirmed the advantages of using a uniform pillar design to avoid excessive loads on portions of irregular pillars. Instrumentation to measure roof convergence and pillar loading was installed at selected locations in an active talc mine but failed to detect any significant changes, suggesting that the gneiss hanging wall constitutes a strong roof that probably can support large spans between pillars and permit high extraction ratios. This interpretation also is supported by a rock classification of the hanging wall gneiss.

Jan 1, 2010

New Mexico?s active coal mines have reclamation challenges that are being successfully resolved through the application of geomorphic grading methods. Soils and overburden material are often of poor quality, and annual precipitation is low. Revegetation on south and west aspect slopes often failed to persist. The New Mexico Mining and Minerals Division had therefore been encouraging topographic diversity on reclamation to improve water harvesting and reduce the percentage of south aspect slopes. Steeply dipping, multiple coal seams may be mined by open pit methods. Structurally-controlled trellis drainage patterns that exist premine have to be replaced with dendritic drainage patterns on reclamation where the overburden had been pulverized. Sodic spoil material is prone to differential settling and the creation of piping features in areas where runoff ponds, which may lead to downslope instability. In each of these scenarios, the approximation of natural drainage patterns on the reclamation has reduced erosion and sedimentation by creating shorter slopes with correct profiles, and by improving conditions for revegetation establishment.

Jan 1, 2010

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By A. Partos

It was decided to build a fourteen-storied office building over a six-storied garage and a four-storied office building. The high vertical and horizontal loads required foundations on rock approximately 18m below street level. Drilled piers (caissons) were selected. Eight caissons (1.98m diameter) were installed through the six-storied garage and four caissons from a temporary deck at the location of a former two-storied building. Excavations were done by the slurry method. Proof testing of rock was done before construction by test borings and during construction with a core barrel of small diameter. Quality control measures included telecommunications between ground crews and the equipment operator on the garage roof; records of field observations and testing of bentonite slurry and rock; and a continuous evaluation of all information. Instruments were installed in one caisson to monitor load distributions and curing of concrete.

Jan 1, 2010

Shallow ore deposits are mined by surface methods but a depth is reached in the case of most deposits after which underground methods are applied for the extraction of the remaining ore. The determination of this depth and its analysis is the subject of this paper. In order to determine transition depth from open-pit to underground mining on the basis of the allowable and economically feasible overall stripping ratios, an economic-mathematical equation is first introduced. Using the achieved equation and an analytical procedure on a particular two-dimensional hypothetical tabulate deposit, an effective formula is then established. The formula introduced here, together with the procedure adopted, could be used in all similar mining situations by the mining design engineer.

Jan 1, 2010

By Z. Y. Liu

A local additional potential model (LAPM) was developed to illustrate the role of strain rate in stress corrosion cracking (SCC) of pipelines. According to LAPM, both density and mobility of the local active spots on the steel surface, i.e., dislocation emergence points, increase linearly with strain rate. Generation of such active spots introduces an additional negative potential locally, affecting the electrochemical reaction and, consequently, the susceptibility of the steel to SCC. Electrochemical corrosion measurements, slow strain rate tests and electrochemical hydrogen permeation test were combined to demonstrate the validity of LAPM to illustrate pipeline SCC in an acidic soil solution. It is found that a maximum of the SCC susceptibility occurs at strain rate of 10-6 s1, which is associated with an enhanced hydrogen evolution due to the local additional potential (LAP) effect.

Jan 1, 2010

By Dennis A. Hansen

As part of a U.S. Bureau of Mines program to develop a more continuous titanium metal extraction process that uses domestic resources, a study was made to determine the extraction of titanium (Ti) and iron (Fe) from New York rock ilmenite using fluosilicic acid (H2SiF6). The effects of leach temperature, acid concentration, and particle size were investigated for the rate at which Ti and Fe are extracted from the ilmenite. Within the leach time studied, the extraction data fit a shrinking-core model; the rate-controlling step was diffusion of H2SiF6 through an ash layer resulting from a heterogeneous leaching reaction. The rate is linearly dependent on the H2SiF6 concentration and is inversely proportional to the square of the particle diameter. Using 2.6M H2SiF6 at 85°C, 49% of the Ti and 53% of the Fe in 44-to 74-µm New York rock ilmenite were extracted in 3 h.

Jan 1, 2010

By M. L. Free

Acid consumption in copper heap leaching is determined by the minerals present in the ore. Gangue minerals such as biotite and chlorite consume acid together with copper-bearing minerals such as chrysocolla and malachite. Acid consumption is affected by the rate of acid application and the particle size. Some gangue minerals undergo alterations and cause precipitate formation during acid leaching. Other minerals form due to precipitation as dissolved ion concentrations from a variety of mineral sources combine to exceed saturation levels. Copper recovery is related to all of these events. This study presents information on acid consumption of various gangue minerals as well as data for copper recovery from an associated copper ore.

Jan 1, 2010

By T. A. Toney

A sampling program was conducted in 2008 to determine the run of mine characteristics of 5 coal seams. The sampling program included size analyses and float sink determinations. The samples were analyzed for ash and mercury concentrations for each size and gravity fraction. This paper will report on the sampling program, the analytical results, and the correlations determined in the data set investigated.

Jan 1, 2010

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2010

By Ulises Crossa Archiopoli

We describe a technique that allows rapid imaging of the thermal diffusivity of the sample by a modified photo-thermal technique. The thermal diffusivity in hardened steels strongly correlates to the hardness. Hence in a noncontact manner and with optical microscope resolution, a 2D map exhibiting the crystallographic phases and hardness of the sample can be retrieved. Two almost collinear laser beams scan the surface, one as a modulated pump and a second as a CW probe. The deflection of the probe carries information on the thermal expansion of the sample and with it, on the thermal diffusivity. It is shown that a single determination of the time delay of the modulation of the probe beam can be used to retrieve the thermal diffusivity.

Jan 1, 2010

By E. Galán

The largest Spanish kaolin deposits formed on granites occur in Galicia (NW Spain) due to a widespread kaolinization of Variscan granitoids. This paper provides insight of the origin of this kaolinization process on the basis of a mineralogical and geochemical study carried out in two kaolin deposits, presently mined to be used in the paper industry. Mineral composition of the deeply kaolinized rocks is dominated by well-ordered kaolinite with minor quartz, K-feldspar, mica (illite/muscovite), locally gibbsite, and traces of resistant accessory phases (rutile, ilmenite, zircon and monazite). The content and structural order of the kaolinite decrease with depth. Kaolinite formed by extensive replacement of feldspars (plagioclase). Differential mobilization of major and trace elements during kaolinization has been inferred by using a mass-balance approach. Significant amounts of Na, Ca and minor Mn, Sr, P and U were removed from incipiently leachable minerals (plagioclase and apatite), and K, Rb, Cs and Ba were released from K-feldspar and mica. On the contrary, Ti, Zr, Th, Hf and the REE are retained in the resistant trace minerals that are concentrated in the fine fractions of the kaolins.

Jan 1, 2010

By Shirleny Fontes Santos

Muscovite mica crystals lower than 15 mm diameter are discarded as waste in the mining area of Borborema-Seridó (BRAZIL). The objective of this work was the ore dressing and purification of this waste to be used in the preparation of pearlescent pigment. Muscovite was dry ground using knife mills and an ultrasound treatment. It was possible to achieve 67% of mica with particle size lower than 100 µm. This product was used in the preparation of brilliant pigments based on muscovite flakes covered with rare earth oxides (CeO2, PrO2, Ce0,95Pr0,05O2). The pigments were characterized by X-ray diffraction, thermal analysis and scanning electronic microscopy. The color of the resulting pigments was analyzed using the CIELAB method and it showed the following colors: muscovite-CeO2 ? yellow, muscovite-PrO2? black and muscovite-Ce0,95Pr0,05O2 ? orange. Those results have shown that ?trash mica? is suitable for use in pigment preparation.

Jan 1, 2010