Search Documents

By Gary Nash

While there could be as many directions on regulations as there are viewpoints surrounding the asbestos controversy, there are a few basic criteria that generally will influence government thinking, namely: - their definition of the problem to be regulated, - their interpretation of the scientific evidence available to them, and - their sensitivities to the views of, and the implications for, various interest groups in society. Clearly, different assessments of these criteria by various governments will lead to differing regulatory regimes. The consequence, of course, is a patchwork of non-conforming regulations among nations, with all that thin implies for the distortion of international trade and the unsettling of international relations. I would therefore argue that when governments are examining regulatory action, they should explicitly take into account their common interests in stable and cordial international relations, and when possible, efforts should be made to ensure that movement on regulation is at least, in principle, in accord with the general views of the international community.

Jan 1, 1984

By R. D. Hagni

Introduction The ore deposits of the Viburnum Trend in the Southeast Missouri Lead District constitute the world's largest lead producing district. Six or seven mines currently are in production in the Viburnum Trend. The principal minerals are few in number, simple in composition, and form simple superposition and replacement textures. The economically valuable minerals in the typical lead-zinc ores of the Viburnum Trend are the sulfides, galena, sphalerite, chalcopyrite, and siegenite. The most abundant gangue minerals are dolomite, marcasite, pyrite, calcite, quartz, and dickite. Four concentrates, lead, zinc, copper, and cobalt are produced from the ores, and they contain an interesting suite of trace elements, of which silver and cadmium are recovered at the smelter and refinery.1 Emphasis is given here to the variations in directions of ore fluid flow based upon interpretations of the positions of orebodies due to the ore fluids being impeded by Precambrian basement relief and upon patterns of ore mineral/metal zoning. The Precambrian basement relief and Lamotte Formation pinchout has exerted an important control upon the specific locations of orebodies in the Southeast Missouri Lead District. The locations of some orebodies along one side of Precambrian knobs or ridges strongly suggests that they are positioned on the side from which the ore fluids flowed. Other orebodies are located in positions that suggest that they formed where the ore fluids passed around or between Precambrian knobs. Patterns of mineral and/or metal zoning have been used in many mineral districts to interpret the directions of ore fluid flow. The mineral/metal zoning pattern correlates closely with that of the mineral paragenesis. The earliest deposited minerals tend to be deposited nearest to the source, the later deposited minerals next closest to the source, and the latest deposited minerals furthest from the source. In the Southeast Missouri Lead District, it is interpreted here that the early-deposited copper-rich ores are closest to the source of the ore fluids, the subsequently-deposited zinc-rich ores are next closest to the source, and iron-rich ores are furthest from the source.

Jan 1, 2006

L50 Adirondack L1 Alaska L2 Arizona L58 Arkansas L66 Billings Petroleum L3 Black Hills L4 Boston L5 Carlsbad Potash L6 Central Appalachian L60 Central New Mexico L7 Chicago L8 Cleveland L9 Colorado L57 Colorado Plateau L10 Columbia LII Connecticut L55 Dallas L12 Delta L65 Denver Petroleum L13 Detroit L14 East Texas L15 El Paso Metals L71 Evangeline L45 Florida L54 Fort Worth L16 Gulf Coast L61 Hobbs L62 Hugoton L68 Illinois Pet Basin L17 Kansas L18 Lehigh Valley L52 Lou-Ark L47 Mexico L19 Mid-Continent L20 Minnesota L56 Mississippi L21 Montana L22 Nevada L64 Niagara Frontier L23 New York L67 New York Petroleum L25 North Pacific L24 North Texas L26 Ohio Valley L27 Oklahoma City L28 Oregon L63 Panhandle L29 Penn -Anthracite L30 Permian Basin L51 Peru L31 Philadelphia L32 Pittsburgh L33 St Louis L34 San Francisco L59 San Joaquin L35 Southeast L36 Southern Calif L69 Southern Calif Pet L53 South Plains L37 Southwest Texas L48 Southwest Alaska L38 Southwest N Mex L44 Spindletop L39 Tri-State L40 Upper Peninsula L41 Utah L70 Venezuela L42 Washington, D C L43 Wyoming L49 West Central Texas L46 Philippine

Jan 1, 1956

By AIME AIME

Russell B. Paul, Chairman of the Special Committee on Divisional Relationships, presented the interim report of his Committee which was published in the September, 1945, issue of MINING AND METALLURGY and a copy of which is incorporated in the official minutes of this meeting. The following specific actions were taken by the Board of Directors in relation to the six recommendations in the Summary of the Report as published: (1) Mr. Haider, Chairman of the Petroleum Division, presented the formal request of his Executive Committee that the headquarters of the new Secretary of the Petroleum Division be established in Dallas, Texas. After lengthy discussion in which the point was made that the success of this program would depend upon effective co-operation between the Chairman of the Division, the Secretary of the Petroleum Division, and the Secretary of the Institute, the request was approved. The new secretary will be selected by the Division and will be employed by the Institute in the capacity of an Assistant Secretary. (2) The following item in the report was approved:

Jan 1, 1945

By Richard L. Sanford

This paper summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory is funded by the U.S. Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 1, 1978

By AIME AIME

The name and address of the school are given first, followed by the length of the regular undergraduate curriculum, the degree granted, types of courses giben, and the name of the man in charge. This covers only work for the first or Bachelor degree in each case. The following abbreviations are used: B. Bachelor Cer. Ceramic. E. Engineer or Engineering Eng. Engineering or Engineer Geol. Geologist, Geological, or Geology M. Mines or Mining Met. Metallurgy or Metallurgical Mng. Mining Pet. Petroleum Ref. Refining S. Science Tech. Technology or Technical

Jan 1, 1939

By Linda C. Carrico

Those who manage the Nation's mineral resources rely upon a variety of organizations both public and private--to give them accurate mineral data, technical guidance, and expert advice. This directory provides a list of such organizations--a list that should prove a useful tool for those seeking mineral-related information and technical assistance. The directory lists Federal and State governmental agencies and national, regional, and State associations with activities in the mineral, metal, and material sectors of the economy. These organizations regulate mining, monitor mineral production, establish and enforce health and safety standards, identify and evaluate mineral resources, conduct scientific research, predict market trends, resolve environmental issues, and promote the interests of the mineral industry, its individual sectors, and its workers--to name a few of their functions. The listings in this directory--arranged by State--should help users who manage mineral resources identify agencies and organizations that can provide mineral-related information or technical assistance.

Jan 1, 1993

By C Placzek, E Beattie, K Blake

Channel iron deposits (CID) consist of ferruginous chemical sediments, and are an unusual subset of Phanerozoic ooidal ironstone deposits almost unique to the Pilbara, where they constitute around 19 per cent of the Pilbara’s iron ore exports. These deposits occupy many of the ancestral river channels of the Pilbara region, especially the Robe River palaeochannels, incising and meandering through the Precambrian banded iron formations (BIF) of the Hamersley Group and the underlying Fortescue Volcanics.This paper explores the factors underlying geochemical variation in CID, particularly the chemical properties of goethite. The selected deposits in the western Robe palaeochannel and its tributaries show little or no secondary reworking by later water tables. There is a total absence of aluminosilicate clays with all the deleterious elements such as aluminium and silica. Instead, these are associated with the goethite mineral lattice, either within or adsorbed to the cortices of pelletoids.A thickly vegetated environment, and the presence of the Maddina Volcanics as potential source rocks for these western Robe CID is offered as an explanation for relatively high aluminium in the deposits studied, and, in turn, as the reason most parts of the palaeochannel are preserved as inverted topography.CITATION:Beattie, E, Placzek, C and Blake, K, 2017. Dirty goethite – a geochemical characterisation of some western Robe River channel iron deposits, in Proceedings Iron Ore 2017, pp 489–502 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Rory P. A. Ball, Mark Briggs, Martin Dix

"Tunnel professionals should inform project stakeholders on the reality that tunnel projects are not 100 percent devoid of the need for excavations or public inconveniences during both design and construction phases. Competing stakeholder objectives to limit these disruptions must be weighed against the need to mitigate risks and to produce a constructible, operable and maintainable end product. Perhaps the approach we should take with stakeholders, also known as Authorities Having Jurisdiction (AHJs), is sharing memorable case studies that bring to life the potential risks so often buried within lengthy risk registers. This paper provides a sobering case study describing what can occur if the presence and/or location of utilities and other obstructions are not fully understood due to restrictions placed on exploration or mining operations. In this instance, the Microtunnel Tunnel Boring Machine (MTBM) encountered a buried concrete structure, followed by rows of abandoned wood piles, before finally colliding with an active high-pressure gas main under a bustling coastal highway. Multiple stakeholders imposed tight logistical and other work restrictions, compounding the difficulties experienced during the drive. However, the difficulties were effectively managed through the project team’s proactive collaboration and communication with everyone involved. INTRODUCTION Some of the most important decisions that influence the ultimate success or failure of a project may not be made by design engineers. Instead, these decisions are often made by project stakeholders and third-party agencies. Tasked with protecting the best interests of their users, these agencies are cautious of potential impacts associated with project construction and subsequent use. Unfortunately, actions required (or restricted) by stakeholders often result in unwanted ripple effects that negatively affect the very users they are trying to protect. For example, a mandate limiting a shaft site to an unreasonable size may be intended to reduce local business impacts, but may actually increase impacts as more supply and truck hauling is required."

Jan 1, 2016

By D. W. Mitchell

Planning today for what hopefully will never happen is one of the surest ways to decrease the chance of it happening. As Napoleon proved and Ian Mitroff wrote, "The heat and stress of battle is the worst time to make decisions of strategic importance." Mitroff also wrote, "The value of a plan is not that it will ever perfectly match reality, but going through the process of planning speeds the process of recovery. It allows the organization to emotionally work through the worst before it actually happens." This paper concentrates on things miners must consider; on the need for plans to be like a belt conveyor strong enough to carry the load, flexible enough to stretch a little; on the criticality of throwing away fax machines and telephones, and having certain officials at the scene rather than back in head-quarters; on the training of fire brigades and mine-rescue teams; on having company-controlled chromatographs; on having people who can look at trends rather than numbers. Some of the things in this paper might anger some readers; for that, I can only ask them to consider first the problem not their position.

Jan 1, 1993

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By L. S. Gertsch, M. Z. Abu Bakar

The research presented here is part of a project to quantify the differences in the mechanical excavatability of rocks in dry and water-saturated conditions. A series of full-scale laboratory linear rock cutting tests were carried out with a long-bladed single disc cutter on dry and water-saturated sandstone blocks. The muck collected from the cutting tests was analyzed to establish a link with the specific energy (SE) of the operation. The coarseness index (CI), a non-dimensional parameter, was found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n was observed between SE and CI. The power n of the relationship for both dry and saturated rock was much lower than found in previous studies. The exponent n is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI was lower for saturated rock than for dry rock, at the same time, saturated rock cutting was found to be less energy-intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate, discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

By Christoph Czettl, Christian Storf, Gregor Kücher, Stefan Luidold

The purpose of this investigation is to provide a basis for the semidirect recycling of hard metals. The present investigation focuses on revealing the fundamental chemical kinetic aspects during cemented carbide leaching in hydrochloric acid media. The kinetic relations of cobalt binder leaching from WC-Co cemented carbide are studied using a central composite face-centered design of experiments with temperature, acid concentration, and hydrogen peroxide as variables.

Mar 1, 2017

By Saeed Salehi Malekshah

In hybrid foundation system or piled raft foundation (PRF), the raft has adequate bearing capacity and piles are usually required to ensure overall stability of foundation and also to act as settlement reducer for high rise structures. When piles are connected to the raft, a high axial stress may develop and one alternative is to disconnect the piles from raft and consider them as stiffeners for supporting soil. This system is known as disconnected piled raft foundation (DCPRF). Cushion, a compacted coarse grained soil layer, can be used beneath the raft to redistribute and adjust the stress ratio of piles to subsoil and plays an important role in mobilizing the bearing capacity of subsoil and modifying the load transfer mechanism of piles. In this study, finite element method (FEM) has been employed to investigate the effect of different parameters such as cushion stiffness, gap height, raft thickness and piling configuration on the behavior of disconnected piled raft foundation. The analysis is performed on different foundations of hypothetical and real case histories. Results indicate that increasing the raft thickness reduces the differential settlement and pile head axial stress. Concentrating the longer disconnected piles similar to connected ones beneath the central area of raft, decreases settlement of raft. With increasing cushion stiffness, vertical stress ratio of piles to subsoil increases, but settlement decreases. Increasing gap height from 0.1 m to 1 m decreases the vertical stress ratio of piles to subsoil.

Jan 1, 2011

By C. Yanqui

"Discontinuum Mechanics is based on two foundations: the idealization of the internal structure of substances, and the principle of the arithmetic mean value. For a linear discontinuum, the methods of Crystallography are used to describe their structure, in which nodes stands for the position of the homologous points such as molecules, grains, or any other motif. The principle of the mean value states that the value of any discrete function at a node is equal to the arithmetic average of the values of this function at the neighboring nodes. This principle leads to an elliptical linear differential equation of the second order, with coefficients given by the statistical second moments of the Cartesian components of the metric vector. As long as those coefficients are components of a symmetric second-order tensor, there are three mutually perpendicular directions, in which the variances reach their extreme values and the covariances are zero, showing that the mean value principle transforms the discontinuum into a statistically equivalent orthotropic continuum.The application of Discontinuum Mechanics to linear rock masses is simple and direct. It is sufficient to define the motif as the plane of geological discontinuity, and the metric vector as the normal vector to this plane, whose magnitude is the spacing between two consecutive planes belonging to the same set of discontinuities. Furthermore, heterogeneities of rock masses can be also included in this description by substituting the plane of discontinuity by a zone of weakness. In this way, the magnitude of the normal vector results from the product of the spacing and the RQD or the RMR. In going further in this theory, at least three conclusions show up. First, in the evaluation of rock masses, it is necessary to determine the orientation, spacing, and RMR for each set of discontinuities. Second, the conventional method of finding the principal families from the contours of equal concentration of poles on the stereographic projection excluding the spacing does not have any physical meaning. Third, any problem of rock mechanics can be solved in a rigorous and reliable way by integrating the differential equation of the mean value."

Jan 1, 2015

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed.The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grade, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the final cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure I."

Jan 1, 1995

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003