Search Documents

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By Layson, W. C.

ACCORDING to the records, Phelps Dodge made its original entry into the production of copper in the oldest copper mines of Arizona at Morenci in 1881. The ore body now being mined as the Morenci open-pit, as outlined by churn-drill holes, diamond-drill holes, and underground workings, is estimated to yield 230,000,000 tons of ore averaging 1.06 per cent copper. This development will add 2,500,000 tons of copper to the 900,000 tons already produced in the district. Some five years ago preliminary development of the ore body began, with big-scale production planned including the erection of a new treatment plant to be built near the mine. Inasmuch as the Morenci open-pit was an entirely new project this required the grading of roads, establishment of mining benches, construction of railroad grades, building of railroad tracks, erection of shops, as well as the purchase of the necessary equipment to satisfactorily and economically maintain the schedules of production forecast. Along with the preparation of the main ore body it was also desirable to mine and deliver to an experimental mill a relatively small daily tonnage of typical ore.

Jan 1, 1942

By GUY B. HUNNER

THOSE magnetite ore bodies comprising the Clifton Mines are situated in the south central part of St. Lawrence County, New York, on the western slope of the Adirondack Mountains. The topography is made up of gently rolling hills densely wooded with second-growth maple, birch, and hemlock. Drainage is north and west to the St. Lawrence River.

Jan 1, 1943

The development of the Moura Coal Preparation Plant is described, commencing with the first'stage of the plant commissioned in 1963. The subsequent expansion stages are traced through to October, 1973. The plant has undergone frequent stages of expansion and modification and this process is continuing. The development programme for 1974 is described as proposed in late 1973. The characteristics of the Moura and Kianga field coal seams with respect to washability are summarised and some comment is made on the blending of these coals prior to washing, to ensure production of export grade coal within specification.

Jan 1, 1974

By L. Weitkämper

The big challenge at present and in the future is the economization of resources. This is applied for the whole industry but particularly in fields of mineral processing. The most important resources are energy and water. The shortage and price advance of energy is worldwide noticeable whereas the shortage of water is regionally limited at present. However due to the increasing world population, associated with a rising standard of living, water will become more and more important. Studies of the Unesco from 2001 indicate that the total water consumption raised seven times since the last 100 years at a growth of population of just three times. (UNESCO-Currier, 10/2001). This trend is going to be increased. While today more than 90 % of the humanity has access to clean water, in 2050 just about 50 % will be in the same situation. These figures indicate the importance of a gentle handling with the resource water. Further more the disposal of fine products, containing most of the water, is an environmental concern and in the future the mining and processing of raw materials will become important and necessary in desert, arid or permafrost areas. In these areas just efficient dry cleaning technologies will allow an economical beneficiation or better enable the processing at all. Most of the separation technologies with high throughput rates in mineral processing are based on wet processes. This applies especially for the separation of fines. Though there are some dry technologies available for the separation of coarse materials, like pneumatic gravity separation [air jigs and air tables], magnetic separation and not least sensor based sorters. Dry separation of fines is bounded mostly on cost intensive and low throughput technologies. The pneumatic separation undergoes at present a renaissance, mainly due to the development of the all air jig by the German supplier Allmineral. This newly developed sorting device yields good results in the separation of coarse to medium size material. All these facts and figures show the potential and motivation for developing an efficient dry separation device for fines. The following article delineates the development, performance and chance of a new dry separation technology for fines.

Jan 1, 2014

By S. Pollak, J. Rickard

The Long Baseline Neutrino Facility Far Site in Lead, South Dakota is currently under construction and involves drill and blast excavation of the largest and deepest caverns in North America. This paper will review how the geotechnical risks are being managed through careful consideration of excavation sequence, completion of exploratory pilot tunnels, implementation of a robust instrumentation and monitoring program, and validation against the design. Aside from having a cross section of 5,900 square feet and being situated at a depth of one mile, the caverns also employ a unique permanent rock bolt solution which underwent a significant pre-production pull testing program involving varying installation methods and being subject to blast vibrations. The behavior of the schistose rock mass and performance of the ground support are being continually monitored throughout the construction phase.

Jun 13, 2023

By J Northfield, L Neesham

The GRE46 Underground Project lies beneath the environmentally unique and culturally endowed shore of Lake Cowal. The ore body is open both along strike and at depth and is currently defined to a strike length of 1.5km and depth of 800m. The Warraga exploration decline commenced in March 2019 and represents the first stage of the Project, which is expected to underpin production at Cowal Gold Operations (CGO) for a period exceeding 10 years. Mining operations at Cowal commenced in 2005, following a period of over 20 years of exploration and permitting. In 2015 Evolution Mining (Cowal) Pty Limited (Evolution) acquired the operation from Barrick Gold Ltd (“Barrick”). Barrick had a life of mine plan that anticipated a cessation of operations in 2024 at a processing rate not exceeding 7.5 Mtpa. Evolution have grown the regional endowment considerably and have a currently approved mine life out to 2032 with a currently approved maximum processing rate of 9.8 Mtpa. This paper examines the history, current status and future path of one part of that plan, the GRE-46 Underground Project. Topics for discussion include discovery, Mineral Resource growth under different ownership philosophies, planning, permitting and commissioning of an exploration decline and bulk sampling project, and integration with the possible future mine. Environmental sensitivities affecting regulatory approvals, timeframes, technical challenges, opportunities and solutions are discussed, along with the path required to fast-track production from the existing 14Mt, 1.4Moz Mineral Resource while complying with the requirements of modern, responsible project development stewardship.

Mar 15, 2021

By E. Thune, F. Stålesen, E. O. Stensholt, O. M. Dotterud, E. E. Henriksen, P. O. Ramsdal

"The development and commercial operation of the Falconbridge chlorine leach process have been described in papers in 1985 and 1987. Since this time, various process improvements have been implemented and the capacity of the Kristiansand refinery has been increased to 85 000 t/y Ni, 40 0000 t/y Cu and 4500 t/y Co. The focus has been on continuous improvements in productivity, the use of energy and other costs. Several environmental issues have also been eliminated or reduced since 1987. IntroductionThe first nickel refining operation in Kristiansand, Norway, started in 1910 based upon raw materials from Norwegian mines. In 1929, Falconbridge Nickel mines purchased the refinery to acquire information and the patent rights to the Hybinette refining process that was practised at the small Kristiansand refinery. Falconbridge ownership has now, for more than 70 years, provided a strong base regarding raw material supply, financial resources and technical support for further expansions and major technical improvements at the refinery.The main concepts of the new chlorine leach process were developed in the laboratories from 1966 to 1969 and the process was piloted from 1970 to 1972. The main stages in the commercial plant were started in the 1975 to 1981 period. After 1981, there have been a number of process modifications, plant expansions and improvements to operating practices. The developments up to 1988 have been described in previous publications (Stensholt et al., 1986, 1988).This paper presents an overview of the process and how it is practised at Falconbridge Nikkelverk AS (FNA) today and describes some of the main changes that have been implemented since 1988. During this time, the nickel capacity has been expanded from 54 000 t/y to 85 000 t/y and the cobalt capacity from 2000 t/y to 4500 t/y. The paper describes how these expansions were achieved together with continuous improvements in operating efficiency and also gives an overview of the main environmental concerns at the refinery."

Jan 1, 2001

By W. Leblanc, J. C. Marsh, D. Kettle, J. Tompkins, G. Hartley

"The Lingan Mine is the newest of the four operating collieries of the Cape Breton Development Corporation and is located on the east coast of Cape Breton Island. Development of slopes began in 1969 using four Dosco Roadheaders. Production commenced in October 1972, when a partial extraction section utilizing a continuous miner, loader and shuttle car was installed. A second Joy unit is scheduled to begin production early in 1973. This paper describes the production and development operations, the ventilation system and the equipment in use at the mine."

Jan 1, 1973

By P. Danson, D. A. White, S. Bashir

Composite ion exchange materials made of SnO2, TiO2 and MnO2 can be used to remove radioactive contaminants from nuclear waste streams. In several cases their selectivity and capacity are enhanced by mixing hydrous silica into the matrix. MnO2-SiO2 materials are especially useful for a number of reasons, such as their selection of heavy elements over caesium. Distribution constants and determinations of exchange capacities show that in many instances the properties of the composites are better than those of the oxides alone, while the presence of a chelating agent has been found to reduce the uptake of nuclides considerably. Methods are being developed for the bulk manufacture of the materials. Further work on sorption mechanisms is required to explain anomalous results, particularly the variation in exchange capacity for different elements and the ability of the oxides to sorb colloidal material in alkaline solution.

Jan 8, 1992

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

Process plant modeling in the computer environment has been developed over the past 40 years by implementing the comminution models formed by the Julius Kruttschnitt Mineral Research Centre, University of Queensland, in the early 1970s. The models for the other processes in a mine value chain, such as blast fragmentation and flotation, were continuously developed and improved in parallel as well. Other research and commercial entities have also developed process modeling methodologies in the computer environment, which evolved as specialized commercial software or through equations set up in Excel spreadsheets. These were performed on a local computer, in thousands of simulations over a long period of time due to hardware limitations and the lack of a fully automated process. This limits the application of detailed process simulations for scale-up and strategic planning analysis, as they require many simulations to cover all possible scenarios which would take a lifetime when using local computers. The Integrated Extraction Simulator (IES), as the next generation of cloud-based software package, has made it possible to run simulations on the entire operation value chain in the same platform, including drilling and blasting, crushing, grinding, flotation, and other downstream process and material-handling units. This capability has allowed IES to handle multivariable simulations across the mine value chain, including pre-concentration and in-pit size reduction, and modify the process simultaneously.

By Tian Yingzhong, Guo XIN, Wei Peihe

The intention is to solve a series of problems in the flotation and desiliconisation of complex bauxite; aiming to achieve monomer dissociation of target minerals based on process mineralogy. According to the mineral surface, there are differences in physical and chemical properties and the molecular design theory of flotation agents. Designing the polar and non-polar groups of the bauxite flotation collector to make the reagent group easily combine with the mineral to form a cyclic chelate, will enhance the collection performance, and strengthen the drug selection performance. Developing a new type of positive flotation collector for bauxite with small dosage, strong selectivity and low foam volume. Keywords: Process mineralogy, monomer dissociation, molecular design, new positive flotation collector

Jan 1, 2020

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers' catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By Mikhail Mikhaylenko

Natural and technogenic sources of rare earth elements (REE) and other rare and scattered metals are remarkable for their chemical diversity. The pregnant solutions going to processing for the valuable metals have very complex compositions. Both targeted elements and competing impurities are present in the solutions in different chemical forms. Thus processing of such materials demands application of different technological tools addressing numerous specific tasks on the way to the final product. Screening work was undertaken to identify the best resins among developmental and commercial products addressing typical cases in the hydrometallurgy of scandium and REE. The cases outline typical sources of scandium and REE, such as streams of TiO2 production, extracted phosphoric acid, barren uranium solutions and others. Specially designed ion exchange resins can be effective tools.

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By P. S. Paul

Mine accidents/injuries are complex and generally characterized by several factors, from technical to social characteristics. In this paper, a sociotechnical model for work injury in mines was developed and tested through structural equation modelling with application to case study mines in India. In total 14 variables were considered in this study. Most of the variables are not directly quantifiable. Instruments were developed to quantify them through a questionnaire survey. Underground mineworkers were randomly selected for the survey. Responses of 300 participants were used for the analysis. The analysis was conducted in three parts. Firstly, high-low plots were constructed to explore the variations in responses to the questionnaires by the accident involved (AG) and non-involved (NAG) workers. Secondly, a t-test was conducted to see whether the responses were significantly different for the two groups or not. The chi-square results showed significant differences of responses among the two groups. Finally, how these difference scan cause accidents/injuries in mines was hypothesized and evaluated using structural equation modelling. The measurement model of the Linear Structural Relations (LISREL) program was used to identify the latent constructs of the sociotechnical model. The structural model of LISREL was used to estimate the interrelationships among the constructs. The case study results showed that there is a sequential interaction among the sociotechnical factors leading to accidents/injuries in mines. Work hazards induce more job stress in the workers while social support mitigates the same. Job stress and safety environment predict the workers? job involvement. A worker who is more job-involved exhibits better safety performance, which in turn reduces work injury. The safety environment is shown to have a direct mitigating effect on work-related injury. The findings of this study clearly revealed that job stress and safety environment are the two key factors influencing work-related injuries in mines that need to be addressed properly through effective safety programmes.

Jan 1, 2005

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By N L. Turner, K Ehrig, V Liebezeit, D J. Robinson, L L. Kuhar, N Francis

Conventional industry tests used to determine leach recoveries are often fully monitored and may be time-consuming and expensive. Such tests may be limiting in geometallurgical applications where large numbers of samples are required to be processed for characterisation of an ore deposit. BHP Billiton currently use a fully instrumented leach test for characterisation of Olympic Dam uranium-rich samples. Researchers at the Commonwealth Scientific Research and Industrial Organisation (CSIRO) were approached to develop an alternative to these full-scale leach tests that could allow for the ranking of samples in terms of their leachability. The novel geometallurgical test was required to use samples of small mass and be affordable and rapid.Three leach test protocols were pursued in developing the small-scale tests. Kinetic leach tests were performed using mild conditions at higher pH, low temperature and low oxidation reduction potential, moderate conditions at intermediate pH, temperature and oxidation reduction potential and aggressive conditions at lower pH, higher temperature and higher reduction potential.This paper presents results from 44 leach tests on 11 samples with varying uranium mineralogy. The developed small-scale tests correlate well with data from the more costly conventional industry laboratory tests, indicating the possibility of using this alternative test as a geometallurgical leach proxy. Simple regression analysis confirmed the importance of pH, reduction potential and temperature on uranium extraction. Experimental data were fitted to published leach models to predict uranium leach extraction for a range of operating conditions.The ultimate aim of the test work is to combine a limited number of large-scale calibration tests, a large number of small-scale geometallurgical tests and leach models for geometallurgical sample characterisation and evaluation of a wide range of scenarios or processing options.CITATION:Turner, N L, Kuhar, L L, Francis, N, Liebezeit, V, Ehrig, K and Robinson, D J, 2013. Development and testing of a small-scale uranium leach for geometallurgical applications, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 345-350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013