Search Documents

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By S. C. Thorley, J. R. Menasce

Trackless mining in low profile (LP) and extra low profile (XLP) platinum stopes has forced equipment designers to re-evaluate their equipment profiles to match the undulating reef. Low profile equipment designed to work in conditions with smooth and flat floors will simply not function with undulating floors and roofs and will become wedged between the floor and roof, beached on undulations due to lack of ground clearance, or suffer excessive mechanical damage. Tyres, too, need special evaluation, as conventional tyres for trackless mining do not work in an extra low profile environment.

Jan 1, 2004

By J. A. Holmes

Due to varying and complex mineralogy, the flotation tailings from the Chingola Concentrator have, for some years, contained upwards of 0.4% acid soluble copper. In 1968, an investigation was initiated, to determine a method for recovering this acid soluble copper. This initial investigation concluded with a recommendation to install a leach-solvent extraction-electrowinning plant at Chingola, to treat up to 900 000 tonnes of material per month, for an additional copper production of some 4 500 tonnes per month. The process consists basically of six stages :- Materials reclamation handling and preparation, acid leaching in air agitated pachucas, solid-liquid separation by countercurrent washing in thickeners, solution concentration and purification by solvent extraction, copper recovery by electrowinning, and residue neutralisation and disposal. This paper describes the development of the main parameters for design of each of the six sections, and gives details of the final plant design. Problems encountered in commissioning and initial operations are commented on, particularly insofar as they indicated any errors or misjudgements in the design. The choice of materials of construction is commented on in some detail.

Jan 1, 1976

By M. D. Scott

A second generation tailings system, consisting of 8 km (5 mile) of large diameter 914- mm (36-in.) po1yethylene pipeline, the bulk of which was laid on a 0.2% grade, has been successfully operated by Lornex Mining Corp. for the past 2 yr. The system was designed to operate as a partial flow pipeline during average flows with the ability to pressurize itself and operate as a pressure pipeline under high flows, or clean itself out under sanding conditions. The system has exceeded design capacity and has had very little downtime. Polyethylene pipe was easily and inexpensively installed and has exhibited superior abrasion resistance characteristics.

Jan 1, 1978

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure'' or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", “canopies” , "roll bars" , protective structures" and other such descriptive names. In this report, "ROPS" describes the function of the structure; "FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection. “MESA” is used as an abbreviation for the Mining Enforcement and Safety Administration; "USBM" is used to abbreviate the U, S. Bureau of Mines.

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By L. B. Guo, S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof-bolt reinforcement of roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening, with variables such as opening width-height ratio, number of bolts installed, number1 location of bedding planes, in-situ stresses, etc. The most critical areas are identified, and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1991

By S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof bolt reinforcement of the roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening with variables such as opening width-height ratio, number of bolts installed, number/location of bedding planes, in-situ stresses, etc. The most critical areas are identified and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1989

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By T. N. Singh, B. Singh

SUMMARY. The supports account for over 501 of the total expenditure for a longwall face. The success and economics of a face depend upon the optimum selection of type and density of the supports. Empirical solutions involving uncertain safety factor are replaced by a geo-mining approach developed at OMRS in which the support resistance is defined by the stability index of the roof rock mass and the failure pattern of the immediate roof. The paper gives the methodology adopted to define the support resistance for Alkusha colliery longwall face of Jharia coalfield (India). The stability index of the roof mass varied from 218 to 520 for the individual beds and 1100 to 1374 for the immediate roof mass. The exact support resistance for the condition was found to be 42 t/m2.

Jan 1, 1982

By Charles V. Riley

While the late 1960's are known as the years of the public recognition of impending environmental crises, the 1970's will be known as the decade of public concern for improving the quality of that environment. One of the present major environmental concerns is the temporary disturbance resulting from coal surface or open cast mining. To realize that this concern will continue in the future, one need only observe the daily news media. Increasing energy demands in the U.S., a doubling of electrical power consumption each decade during the present century, and the projected needs for the remainder of the century are indica¬tions that coal surface mining as a major extractive industry will continue. Coal and lignite, prime energy resources and extremely abundant in these United States, in the face of seemingly limited gas, oil and uranium reserves, are both destined for expanded future use. Presently some extremely serious techno-logical and environmental problems are associated with the develop¬ment and use of nuclear power. It is true that the extraction and use of coal as an energy fuel poses disruptive problems for the environment, but the solutions to many of the problems are known or can be solved within a reasonable time framework. Certainly our national well-being and continued survival, as a free nation within the world community, automatically dictate the continued use of the coal resource for energy. Concurrently, those engaged in coal surface mining, with the temporary disturbance of the land and water resources, must also realistically conclude that public concern for maintaining and improving the quality of the environment will not diminish. Although as ecological, economic, social and aesthetic elements

Jan 1, 1972

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By Paul M. Wiltcher

This paper discusses how benefits in engineering design can be achieved from combining existing GRP concrete design guidelines with carbon steel design codes primarily made possible due to the increase in the constitutive properties of modern composite rebar or GRP. It also examines the technical and practical considerations necessary to both construct and ensure the integrity of composite rebar during transportation and handling on site and the measures taken by Franki-Cementation Joint Venture to ensure the safe deployment of the GRP in the workplace on the Noord/Zuidlijn Project in Amsterdam between 2003 and 2006.

Jan 1, 2006

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021

By Joseph Goessling, Mark Kroncke, James Parkes

The I-35 Capital Expressway (CapEx) Central Drainage Tunnels will serve as a stormwater collection system for the forthcoming I-35 Capital Express Central reconstruction project through downtown Austin, Texas. The schematic level concept design included three tunnels, 10 to 14 ft ID, totaling 26,000 LF. Constructability reviews during design development indicated issues with the concept design including phasing of construction, conicts with future retaining walls, staging area concerns, and signicant mixed face tunneling. The design was updated to mitigate these risks. The revised design includes two tunnels, both 22-ft ID and totaling 33,000 LF, that will be mined almost entirely in rock.

Jun 23, 2024