Search Documents

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By Luis E. Vallejo

The strength measured by the uniaxial compression test is a parameter that is widely used for the engineering classification of rocks. Sedimentary rocks such as shales, however, are difficult to evaluate by uniaxial compression tatting because the rocks slake during the preparation of the standard samples required for the tests. Indirect methods such as the point load test have been proposed to determine the unconfined compressive strength of shales and other soft rocks. It is current practice to use 24 as the conversion factor between the point load strength, Is, and the unconfined compressive strength, sf (sf = 24 Is). The present study investigated index-to-strength conversion factors for shales and sandstones obtained from surface coal mining sites in the Appalachian region. Regression analyses indicate that a conversion factor of 12.5 best correlated the strengths obtained from the point load and unconfined compression tarts in the case of shales. For the sandstones, a value of 17.4 best correlated the strengths.

Jan 1, 1989

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By D. A. Beattie

Talc is a commonly encountered gangue mineral in metal sulfide flotation. Talc is naturally hydrophobic, resulting in high recoveries if polymeric depressants are not used to specifically reject this MgO containing mineral. We have studied the adsorption of a selection of polymers onto talc using a variety of techniques. Adsorption isotherms have been determined using ex situ depletion techniques and in situ ATR-FTIR spectroscopy has been used to determine adsorption kinetics. Adsorbed layer thicknesses have been determined for the polymers on cleaved talc surfaces using the AFM. The effect of the adsorbed polymer layer on the properties of the talc surface has been quantified through contact angle measurements and single mineral flotation tests. Distinct correlations are observed between the adsorbed layer properties and the flotation performance of the polymers. These observations are discussed with reference to the bubble-particle attachment process and the molecular structure of the polymers.

Jan 1, 2006

By A. W. Khair, S. J. Jung

"IntroductionIn a typical incremental loading test, the AE activity increases rapidly in the initial stage of the loading. It is associated with initial closure under compression of favorably oriented cracks already present, together with sliding of crack faces against each other /1/. After the initial stage, crack closure and movement largely cease and the AE activity drops to a barely detectable level /2/. In the final stage of loading test, cracking associated with the onset of inelastic deformation' occurs, and the rate of AE rapidly increases /3/ indicating an increase in the •number of events associated with higher number of microcracks. To understand better primary fragmentation process, Anderson and Ruzzi conducted tests to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool /4/. They proved that a relationship existed between the AE activity, generated during fracturing and the amount of fracture surface area created.A process of fragmentation, demonstrated by conical bits acting orthogonal to the flat surface of block of coal specimen with and without lateral confining pressure is presented here. The monitoring of AE during the fracturing process of rock/coal has been a very useful indirect method in studying fracture mechanism.Specimen PreparationLarge blocks of Waynesburg coal were obtained from a surface mine. These blocks were then out and molded to approximate dimensions of 25.4 x 25.4 x 15.2 'an (10 x 10 x 6 in.). These specimens were instrumented with three strain gages in a 45 degree rosette. One was mounted parallel to the bedding plane direction, another was tinted at an angle of 45 degree from the bedding plane direction and the third was mounted perpendicular to the bedding .plane direction. Each of the three strain gages were set 5.1 an (2 in.) away from the impact point.Typical Test ProcedureIn a typical experiment, the specimen was placed in the confining chamber.Predetermined equivalent in-situ stresses were applied to the specimen by using two sets of hydraulic cylinders. Two 1 in. thick steel plates ware positioned between the sample and the hydraulic cylinders in order to distribute the pressure uniformly over the whole surface of the specimen. The LVDT null position was adjusted with respect to the coal face. After setting the LVDT, the bit and associated weight was lifted to a predetermined height (equivalent to a predetermined kinetic energy) by a win. The three strain gages were balanced using the signal conditioner and the output was recorded by a 6 channel strip chart recorder. The experimental set-up is shown in Figure 1."

Jan 1, 1989

Correlation of Air Recovery with Thin Film and Froth Stability in Flotation

Sep 13, 2010

By R. M. Brick

THE etched microstructures of cold-worked alpha brasses, after reduc-tions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonomously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {111}, in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson5 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into sym-metry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By E. R. Phelps

A determination of feasibility of a new surface mining project requires a study in orderly fashion through the procedures outlined in Section 2 and the previous two chapters of this section. The information and data collected as described in Chapters 3.1 and 3.2 must be correlated, and the many variables that affect the venture must be reviewed. This review will furnish the mining engineer with the information required to make a preliminary evaluation of estimated profit in the venture. It is at this time that management must make yet another decision whether to drop or continue the project. 3.3-1. Maps. For the purpose of collecting, outlining, and correlating a large portion of the data required for a surface mining feasibility study, maps are essential. A map to a mining engineer is like a sheet of music to a musician, or a blueprint to a designer. It provides a pictorial method of presenting mining information not only for practical application in estimating and planning, but also for demonstration of physical relationships to those charged with decision-making responsibilities. GENERAL AREA MAP. The first step in the process of graphic information assembly is the preparation of a "small scale" general area map. Such a map may cover a mining district, a market area, a watershed area or district, or the whole or a section of a geologic feature such as an iron formation or coal seam. An example of such a general area map is shown in Fig. 3.3-la which outlines the various coal mining areas in the vicinity of a proposed "mine-mouth" power station, the Liddell Power Station Project. If Quadrangle Maps of the United States Geological Survey, or their equivalent, are available for an area, a common and very effective technique is to superimpose mining data on these maps, either directly or by means of transparent overlays. Valuable topographic information

Jan 1, 1968

By R. H. Card

THE geophysicist is interested greatly in the resistivities of different formations or parts of the earth's crust; sometimes he is interested in a single figure in the nature of an average, or what may be called the effec-tive resistivity, of all the formations or parts of the crust at a given location to a certain depth. Conversely, the engineer whose work is concerned with the coordination of power and communication lines in such a manner as to avoid electrical interference between these two types of facilities is concerned very much with this effective resistivity; to a lesser extent he is interested in the resistivities of individual forma-tions. In connection with his work the coordination engineer often estimates the effective resistivity; of the earth from measurements of the mutual impedances of lines; in other instances he derives front measure-ments of a different type the resistivities of different layers of the crust and synthesizes these to obtain an estimate of the effective resistivity. In connection with problems concerning the coordination of power and telephone lines, measurements from which earth resistivities can be estimated have been made at many points in the United States by the American Telephone and Telegraph Co. and its associated companies, in cooperation with various power companies and with railroad companies having electrified sections of line. Other such measurements have been made by the Joint Subcommittee on Development and Research of the Edison Electric Institute and the Bell Telephone System. A study has been made of the correlation of these data with the ages and types of materials of the strata of the earth's crust at each of the test locations. The purpose of this study has been primarily to provide information to assist in predicting the order of magnitude of effective resistivities to be used in the preliminary consideration of problems con-cerned with the coordination of power and communication lines. To make the results of such a study, most useful, it is essential that the geo-logical data to be secured when such a prediction is wanted be readily obtainable. Data on the ages of strata and the types of materials com-posing geological structures can usually be obtained, therefore particu-

Jan 1, 1937

W. 0. HOTCHKISS,* Madison, Wis.-When we began to do geological field work in the Lake Superior region, we found a correlation in existence, and, as youngsters, accepted all that as settled. Both Mr. Allen and I, since that time, have seen a great many things that were not apparent nor visible to Van Hise, and those who worked with him; we realize now that the correlation was not final and that much remains to be determined concerning geology of the Lake Superior region. My attitude on this matter is that we should not publish an amended correlation as a final thing. We should avoid, in every way possible, foreclosing the minds of those who follow us in working in the geology of this region. As a matter of fact, no correlation can be final at present, because facts and data are accumulating so rapidly that every classification must be immediately modified to fit further observation. Consequently, my attitude in this matter would be, instead of saying that the iron formations of the Lake Superior region are all Middle Huronian, to say that there may be three Huronians-or four or five- we do not know. I believe it is better policy to hold to our present correlation. I do not believe there is any economic benefit to the mining man or the geologist working on problems relating to explorations for iron ore, that cannot be just as well solved by maintaining our present correlation, with a. wholesome idea of our lack of knowledge and the necessity for further detailed work. Then, if any new horizons are discovered in any particular range, the minds of the investigators will not be foreclosed because some one has said that all the iron formation is in the Middle so that there is no use looking elsewhere for it. There is use looking elsewhere, in many cases, as the ore deposits become exhausted.

Jan 1, 1920

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By A. F. Buddington

INTRODUCTION EVER since a genetic connection between many ore deposits and magmas began to be widely recognized, some two-score years ago, there has been much discussion of the complex and intricate problem of the genetic association of specific kinds of mineralization with specific kinds of igneous rocks. General discussions of the latter problem and pertinent data have been given by S. F. Emmons, Kemp, Lindgren, Niggli, Rastall, Spurr, Vogt, and others. In this paper no attempt is made to deal with mineral deposits genetically associated with volcanic rocks, but only with those presumed to be related to exposed intrusive masses. The writer is indebted to E. S. Bastin, F. F. Grout, Edward Sampson, and to the members of the committee in charge of the preparation of the volume, for a critical reading of the manuscript and many worth-while suggestions.

Jan 1, 1933

By Henry Rawdon

ANY laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test, " that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929

By A. A. Afshari, D. G. Frazer, C. F. Stanley

"INTRODUCTIONThe primary function of the lung, i.e. gas exchange, occurs in peripheral units termed alveoli• Diagnosis of lung dysfunction ls therefore dependent on techniques to evaluate the status of the peripheral airways. Since these airways and alveoli are very small, it is difficult to determine directly how they function or how the function is changing due to disease. Yet this unde1·standing is critical to the design of instrumentation to detect early changes in lung function due to disease.An interesting hypothesis describing one aspect of small airway function has been proposed by Frazer (1) as gas trapping due to the formation of menisci in the airways. An additional study (2) proposes that the breaking and possibly the formation of these menisci could generate lung sounds, i.e. crackles. These lung sounds were recorded by placing a microphone at the trachea of an excised rat lung. The lung was degassed and then inflated and deflated. At points along the path of inflation, lung sounds were recorded. However, determination of the origin of the sounds was not attempted due to the difficulties induced by contacting the lung st1rface with a microphone.The purpose of this paper is to describe a non-contacting, whole field technique to monitor and describe the movements of the lung surface during inflation - deflation cycles.HOLOGRAPHIC INTERFEROMETRYHolographic interferometry is a full field, non-contacting and non-destructive technique that measures deformations of an object with a sensitivity in the order of the wavelength of light. A laser beam is split, with one beam reflected from an object and the other used as a reference beam. Both beams combine to produce a hologram of the object on a photographic plate. The process utilizes the concepts of interference, i.e. the two wave amplitudes will add at the points where the difference in optical path lengths over the exposure period is zero or a whole number of wavelengths and will subtract at other points."

Jan 1, 1989

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013

By Ian Buterbaugh, Calvin Lo, Tomoko Sano, Brendan Koch, James Catalano, Timothy Walter

In this research, two grades of alumina, one at nominally 85% composition and the other at 99.5% were characterized. Microstructural and phase characterization was conducted using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, X-ray Diffraction, and micro-computed X-ray tomography. It was determined that the Knoop hardness values were influenced by the porosity in the 85% composition. Quasi-static compressive tests and high strain rate compression experiments were conducted to determine the influence of the microstructure to the compressive properties. It was observed that the overall compressive strengths increased with strain rate. Although the Knoop hardness values were much lower in the 85% alumina due to the porosity, the compressive strength at both quasi-static and dynamic strain rates were not significantl lower than those of the 99.5% composition.

Mar 1, 2018

By E. J. Peterson

Oil shale retorting induces mineral and chemical reactions to occur on the macroscopic and microscopic levels in the kerogen-bearing marlstone. The nature and extent of the reactions is dependent upon process variables such as maximum temperature, time at temperature, atmosphere, and raw shale composition. This report describes the investigation of the mineral, chemical, and trace element release properties of spent shales retrieved from an experimental in situ retort at Occidental Oil Shale, Inc. 's Logan Wash site in Garfield County, Colorado. Correlation between mineralogy of the spent materials and the mobility of major, minor, and trace elements are indicated, and relationships with important process parameters are discussed. The progress .of carbonate decomposition reactions and silicat ion reactions is indicative of the processing conditions experienced by the shale materials and influences the mobility of major, minor, and trace elements when the solids are contacted by water. Shale minerals that are exposed to the extreme conditions reached in underground retorting form high temperature product phases including akermanite-gehlenite and diopside-augite solid solutions, kalsilite, monticellite, and forsterite. The persistence of relatively thermally stable phases, such as quartz, orthoclase, and albite provide insight into the extremes of processing conditions experienced by the spent shales. Leachate compositions suggest that several trace elements, including vanadium, boron, fluoride, and arsenic are not rendered immobile by the formation of the high-temperature silicate produce phase akermanite-gehlenite.

Jan 1, 1981

By D. J. A. Chambers, J. M. Wempen, K. D. Koper, M. K. McCarter, K. L. Pankow

"The EarthScope Transportable Array (TA) of broadband seismometers (www.usarray.org) was deployed across southwest Wyoming from November 2007 through May 2009. During this time period the Array Network Facility (ANF, anf.ucsd.edu) detected and located a total of six seismic events near the trona-mining district. This lack of seismicity is atypical compared to coal mines employing similar mining methods. In this study, eighteen months of continuous seismic data from several nearby TA stations are reexamined using conventional and correlation-based methods to detect seismic events. Waveform cluster analysis and epicentral locations are used to discriminate between mining induced seismicity (MIS) and seismic energy generated from surface blasts at nearby coal mines. The locations and magnitudes of the 143 newly detected MIS events are compared to regional subsidence as measured by Differential Interferometric Synthetic Aperture Radar (DInSAR). INTRODUCTION An abundance of natural resources and a favorable political climate have made southwest Wyoming home to multiple large mining operations. Among these operations are five underground trona mines located approximately 50 km west of Rock Springs, Wyoming. The trona mines employ room and pillar, longwall, and solution mining methods over an area roughly 900 km2, and produce a sizable portion of the world’s soda ash (Brown 1995). Historically, in the Rock Springs mining district, several relatively large magnitude seismic events have occurred. These events are thought to have been related to mining activity and have caused notable subsidence (Case 1997). The largest event in the region recorded by seismometers, ML 5.1, has been confirmed as the 1995 Solvay Trona Mine collapse (Pechmann et al. 1995). In addition, blasting at surface coal mines near Rock Springs produces significant amounts of seismicity; approximately 50% of all daytime seismic events in the Mountain time zone from 2007 to 2009 locate near an active surface mine in this region (Astiz et al. 2014). Much of the current research related to surface subsidence and induced seismicity focuses on wastewater impoundment (Ellsworth 2013) and hydraulic fracturing. The observable seismicity in geological injection environments is widely variable and McGarr (2014) has argued that, in such environments, the maximum amount of seismic energy that can be released is proportional to the injected volumes. Like injection environments, in extraction (mining) environments seismicity is highly variable depending on many geological and operational variables (Boltz et al. 2012; Carnec and Delacourt 2000; Fritschen 2010; Iannacchione et al. 2005; Sen 2013) and does not always correlate well spatially with subsidence, a surface expression of extraction at depth."

Jan 1, 2015

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991