Search Documents

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By A. J. Magerowski

Energy consumption is a main component of operational costs for the comminution of mineral bearing ores. Reduction of energy consumption has continually been addressed by mill operators and equipment manufacturers. Our testing over the last few years strongly indicates that the overall energy needed to comminute a mineral bearing ore can be brought down significantly, if more work is done in the crushing stages of the comminution circuit.This calls for uprating of the conventional crushing equipment into a new generation of crushing equipment to produce finer products. This will result in the emergence of new ideas in the design and application of equipment and corrnninution circuits.

Jan 1, 1986

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By M. D. Flavel, J. C. Motz, G. V. Jergensen

Introduction Compared to the gyratory crusher, the cone crusher is character¬ized by its higher speed and a flat crushing chamber design which is intended to give a high capacity and reduction ratio for materials suitable to this type of processing. The aim is to retain material longer in the crushing chamber to do more work on material as it is being processed. A concept of how a piece of stone might flow through a secondary crushing chamber is shown in Fig. 45. The number of times material will be nipped during crushing will depend on material size, friability, and the geometry of the crushing chamber as well as its speed and eccentric throw. Cone crushers are usually specified in terms of closed-side setting (CSS) and a given quantity of material passing a particular square-mesh screen size. A criterion of product passing closed-side setting is often available. This value will vary according to the particular crusher design and the details of its applica¬tion. Essentially, cone crushers can be classified into distinct types, depending on their duty. Crusher sizes for all duties are described by terms arising out of common industry usage, such as 3-ft, 7-ft, etc., which refer to the crushing-head (mantle) diameter. At present the range of sizes available varies from approximately 2 to 10 ft diam. Weights vary in the range of 5 to 200 tons, and connected horsepowers range from 10 through 700. There are so many variations that specifics should be obtained from machine manufacturers. The crushing chambers that are fitted to various machines are also often referred to by terms arising out of common usage, such as standard for secondary crushers, and short head for tertiary crush¬ers, which refer specifically to the Symons design. Also used are more specific but equally vague descriptions, such as coarse, intermedi¬ate, and fine chambers. Some manufacturers such as Allis-Chalmers with their Hydrocone crushers refer to the model number of the machine by the feed opening and the diameter of the mantle. For example, a Model 10-84 Hydrocone crusher has an 84-in. diam man¬tle, and is capable of accepting a 10-in. diam sphere at the feed point to the crushing chamber. Rexnord and Telsmith define crushing cavi¬ties in their capacity tables as feed openings at minimum recommended discharge settings (closed-side settings). Each practice offers guidelines which should be carefully defined for the specific crushing problem. The utilization of a cone crusher depends on how well it is controlled and the features of the circuit in which it operates. Normally, it will operate in the range of 75 to 85% of the peak capacity. It is likely that industry pressures will call for a standarized de¬ applied crushing power. Experience has shown that the crushing process is more controllable if certain reduction ratios are adhered to for each stage. Technically, this is defined as that size of feed (in. or mm) of which 80% will pass, divided by the size of the product (in. or mm) which 80% will pass. Secondary Crushers These are the cone crushers which accept suitable feed size material either prepared by a primary crusher or occurring naturally, and reduce it to a size suitable for marketing in one stage, or make feed for subsequent crushing or grinding stages. Secondary crushers have feed openings of 4 to 25 in. in the larger (7-ft) models down to a 2'/a to 4 in. in the smallest 24-in. models. Reduction ratios normally range between 3:1 and seldom more than 5:1. In the 7-ft models, the cone crusher typically makes a product all passing 2 in., but this is dependent on the machine design and properties of the material being treated. Secondary crushers most commonly operate in open circuit. They also are operated in closed circuit with a vibrating screen, depending upon product requirements and conditions where the reduction ratio does not cause excessive power draw and build-up of circulating load. Screening ahead of secondary crushers is generally recommended, especially where the feed contains more than 25% material smaller than the desired closed-side setting. Tertiary Crushers These are cone crushers that normally take secondary crusher product and reduce it to a marketable product or make it suitable for subsequent comminution steps. The reduction achieved is a func¬tion of the crusher design and the properties of the material to be treated. The reduction ratio is normally in the range between 1.5 and 2 to 1, and seldom more than 3 to 1. The tertiary crusher normally operates in closed circuit with a vibrating screen and makes a product smaller than all passing 'h or 5/8 in. Fine Crushers Sometimes these machines are called sand crushers and are called by various manufacturer brand names, such as Gyradisc, Hydrofine, V.F.C., and others. A cross section of a Symons Gyradisc crusher is shown in Fig. 46. Essentially, these crushers would be used in a fourth-stage crushing operation, but could be called on to reduce a screened feed size fraction from a secondary or primary crushing operation. This type of crusher normally receives feed no coarser than 1'h in. that is scalped of all over-sized material and operates in closed circuit with a vibrating screen. For average materials, typical product is '/e in. top size, although a -10 mesh product can be produced on those materials having suitable characteristics. The crusher is nor¬mally operated in a separate circuit from the main crushing plant because of the variations in output rates that are caused by varying physical properties in the feed. The reduction ratio is generally less than 2:1, and circulating loads are generally high. More interparticle crushing takes place in these machines than with conventional cone crushers and capacities can be more sensitive to changes in moisture content, feed size graduation, and other physical properties. Design Features For the various applications, crusher manufacturers normally have a range of crushers of different sizes and power ratings to select from.

Jan 1, 1985

By D Reid, A Fourie, J Ayala

This paper discusses cone penetration test correlations for loose gold tailings that were developed within a critical state soil mechanics framework. The development of a new calibration chamber for cone penetration testing that consists of a modified triaxial cell is described. Some of the early development and commissioning issues that were encountered, as well as the solutions adopted are outlined, including the system to prepare the samples and to acquire high-quality data from the testing. Also, the triaxial laboratory testing required to achieve the critical state line is described, including some of the basic precautions considered necessary as good practice. Additionally, the system adopted for volume tracking of the calibration chamber sample is described, which is essential for ensuring a reliable state parameter comparison against the acquired cone penetration test data. Finally, some laboratory test data from the calibration chamber is plotted against the soil behaviour type charts currently available from various authors.

Jul 1, 2021

By Baltus Cornelius Bonse

Foi desenvolvido um composto de elastômeros termorrígido (ebonite) para a fabricação de um selo mecânico de vedação de hélices de barcos, para substituir os modelos comumente encontrados de cerâmico, que possuem alto custo e são fabricados no exterior, e de borracha com face em Teflon®, que apresentam problemas de adesão na linha de junção entre estes materiais, resultando em vazamentos. O composto de elastômeros deveria possuir dureza em torno de 90 Shore D, baixo coeficiente de atrito, resistência térmica, a abrasão e a intempéries marítimas, ao ataque de radiação UV e ser autolubrificante. A formulação que resultou no melhor produto consistia das borrachas natural, nitrílica, nitrílica carboxilada, e fluorada (Viton®), aditivadas com alto teor de enxofre (37,5 phr), cargas reforçantes, plastificantes e lubrificantes sólidos, entre outros aditivos. A aditivação e mistura das borrachas foram realizadas em misturador interno Banbury e misturador de cilindros aberto, enquanto a conformação e vulcanização dos corpos de prova e dos selos foram realizadas por prensagem a quente. Foram realizadas análises de curva reométrica, morfológicas por microscopia eletrônica de varredura, de resistência à tração, rasgo, dureza e de abrasão em torno mecânico simulando a pressão de vedação em atrito com o aço inox girando a 800 rpm. O êxito do selo ficou evidente, pois após a montagem em barcos, durante um ano tem realizado com sucesso a sua função.

Aug 8, 2018

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By F. R. Hensel

P. R. Kalischer.*—I should like to amplify a little one of the points made by Dr. Hensel, and rather violently disagree with him at the same time. He brought out the point that when the higher forming pressures are used on the green compacts there is a marked decrease in the density as sintered. We found that to be true and, of course, many of you notice that that is true with copper compacts also. But, in my opinion at least, it is not true that the expansion is due to entrapped air. We have vacuum-pressed both silver and copper compacts and obtained almost exactly the same numerical expansion as we secured by pressing in air. The powder, however, that is vacuum-annealed does show a slight decrease in expansion on sintering, but almost the entire increase on expansion can be overcome by very slow rates of heating. And it is our opinion that a majority of the expansion is due to dissolved oxygen in the discrete metal particles themselves rather than to entrapped gases. Another interesting observation that we have made is that often with silver or copper compacts it is desirable to silver solder or braze the compact into some part of a piece of equipment after completing powder metallurgical operations on it. If such a compact is sintered and coined, say a silver compact, given an initial forming pressure of 10 to 15 tons per square inch, and sintered, there is an adequate amount of shrinkage and it can be coined at about 50 or 60 tons per square inch and bring up the density nearly to theoretical. If, then, that compact is silver-soldered into some part of a fixture or a machine, it will expand very beautifully, and the only way that this can be overcome. as far as we know, has been to reanneal after the coining operation at a temperature higher than is to be used in any subsequent operation. In that way, a density very nearly theoretical can be achieved, but the coining operation cannot be carried to the excessively high pressures or expansion and bubbling of the compact will occur again.

Jan 1, 1945

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By E. I. Larsen

Powder metallurgy has been described as being "as old as the pyramids and yet as new as the latest bomber." While this may be true literally, it has been only in the last Io or 1 5 years that widespread use has been made of this method of fabricating various articles One of the first items fabricated by powder metallurgical methods on a commercial scale was electrical contacts, which were fabricated from metal powders as early as 1920. The reason why these contacts have been made for so many years by powder metallurgy is because the compositions of most of these materials arc such that they could not be made by the conventional methods of melting, casting, rolling, drawing, etc. Classes of Contacts In general, electrical contacts fabricated from metal powders fall into two classes, both from the point of view of the method of fabrication and the components that make up the chemical composition. One class is composed of silver or copper and a refractory metal such as tungsten, molybdenum, or compounds thereof such as carbides. The second class contains a predominant amount of silver and a semi-refractory material such as cadmium oxide, nickel, cobalt, or graphite. Electrical contacts of the first class have been developed primarily as facing materials for heavy-duty circuit-interrupting devices. This class of material unites the high melting point, high boiling point, great resistance to electrical erosion, and the refractory characteristics of molybdenum, tungsten, or their carbides with the high thermal and electrical conductivities and low contact resistance properties of silver or copper. The second class of material is used for lighter duty or specialized applications such as heavy-duty, direct-current aircraft relays. Varieties Electrical contacts fabricated from metal powders are made in a wide variety of compositions, shapes, and sizes. In general, the sizes of electrical contacts fabricated from powders vary from contacts weighing approximately 0.001 oz. up to those weighing 3 to 4 Ib., the contacting face being as small as 0.001 sq. in. up to approximately 6 sq. in. in area. The shapes consist of: sound or rectangular buttons, some of which have radii or bevels on the contacting faces; rings, cups, rectangular bars, the contact face of which may have a radius across the width and/or at one end; and form-pressed pieces of a wide variety such as angles, both acute and obtuse, irregular shapes comprising a radius blended into a flat, which in turn may have steps. The size or shape of the contact is dictated principally by the mechanical design of the manufacturer, who in turn may have problems to be met such as: (I) size, weight, or space limitations; (2) electrical conditions such as blowout coils arc chutes, baffies, gas passages.

Jan 1, 1945

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By A. J. Langhammer

A. J. Langhammer.—That is rather asking a question of the wrong man. However, I will reply to the question from our point of view. There is a considerable amount of iron powder available but the properties vary over a wide range. Powder metallurgy has progressed to the stage where we recognize certain requirements in powdered iron, and what may be a good powdered iron for one application will not necessarily fit the picture for the next one. Further, I believe that there is room for great improvement in the properties of powdered iron. Also, that there is only a limited quantity of powdered iron available having certain specific properties in which we are at the moment interested. F. P. Peters.—May I have a word? With all possible respect to the contributions of the Chrysler Corporation (and they have been tremendous) to the war effort, I think it is easy to get from part of Mr. Langhammer's discussion a false impression of vaster possibilities than really exist. It would be well if in addition to Mr. Langhammer some other manufacturers of machine parts' might tell us in the next few minutes some of the limitations they have found. For example, what is the maximum tensile strength that is being produced in a commercial part in production today? And what is the actual size limitation on bearings that are in operation and are standing up well? We should always bear in mind the fact—and I think Mr. Langhammer will agree with me— that quoting on a particular part does not necessarily mean placing it in production. In many cases it may be several months before the quotation is resolved and we know whether the part can be made. Let us open up this thing for a little free-for-all discussion of some of the ceilings that do exist in the design of machine parts made by powder metallurgy. The ceiling is not unlimited, and Mr. Langhsmmer will agree with that, 3 am sure. H. Hendriks.*—I do not think that there is so much limitation in the making of powder metallurgic manufactured parts as mentioned. Last year we had the problem of making dies for a special machine used in the manufacturing of slide fasteners. This part was wearing out very fast. It was very hard to make, it had to be hobbed out of a special steel and it was a difficult thing to manufacture in general. The tolerances were one half of one thousandth of one inch on all dimensions. We submitted this die to a manufacturer of powder-metal parts. He thought that it was impossible, but we were not as skeptical as he was and decided to try it anyway. The Canadian General Electric Carboloy Division, in Toronto, gave us then the design for the dies, which we made to their specifications. When the first part was delivered, we submitted it to our Inspection Department and its check showed that all the tolerances were right on the dot. They delivered I9 parts of exact specification, then they went off the beam; they could not keep to the tolerances. It took them a long time to get back again. We do not know what happened, but the main point I want to' make is that if a problem is attacked in the right may, the dies are made right and corrected as to dimensions found out by experiment, I do not think that there is so much diffculty in making powder-metal parts to close tolerances.

Jan 1, 1945

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945

By Jerome F. Kuzmick

Condusions. From the work on aluminum powder, the following general con clusions can bc drawn: I. The physical properties of aluminum compacts, such as density. strength and ductility, increase with increasing pressure, up to the practicable pressure limits. 2. Good properties ill aluminum con pacts can be secured only by the use of high pressures, because it is neccssary to rupture the refractory oxide film on aluminum powder. 3. Considerable softening of the specimens occurs upon sintering. regardlers of the pressure used. General Conclusions 1. For relatively short-time sintering. molding pressure is a very important factor in the final physical properties of the sintered specimens. 2. The effect of pressure. is difierent for each metal, so that few general rules can be drawn that would apply to all metals. 3. In many cases, fur a particular metal powder and sintering temperature there is a critical pressure at which the best physical properties can be obtained. 4. The principles of cold work and in nealing and their effect on grain structure applied to massive metal also holds true for sintered metals. 5. Particle size, at least for electrolytic iron powder, does not have a. great effect on ultimate grain six. DISCUSSION [E. E, Schumacher presiding V.. V. Crane. *—I was particularly impressed with Dr. Kuzmick's work on tin IF not the illustration, particularly the Second one. a very good illustraition of hot preessing. in that

Jan 1, 1945

By C. G. Goetzel

E. V. Crane.*—I want to ask Dr. Goetzel concerning the control of atmosphere in heating and pressing. Was the heating and pressing done in the die, or were the two kept separate there? C. G. Goetzel.—The setup used for this investigation implied heating the die to the temperature at which the work was to proceed, introducing a preformed compact into the hot die. The atmosphere was supplied through an annular chamber from which it passed through two holes into the die cavity. E. V. CRane.—The compact was not preheated? C. G. Goetzel.—The compact was not preheated. Tee Chairman.—In the course of recent studies on the effect of time of heating upon the tensile strength and hardness, I have observed that there is often a maximum in tensile strength and hardness reached before complete homogenization has been attained. The magnitude of each mechanical Property changes rapidly with time in the early stages of sintering, the more so as temperature increases. For these reasons it seems that the comparison of values obtained by heating for the same time at a series of temperatures may be deceptive. Not only may those heated at higher temperatures give higher tensile readings, but the reverse may be true if the maximum in the tensile strength versus time curve has been passed. A better basis for comparison would be that of equal degree of diffusion. C' " Goetzel.—Thank you, Professor Rhines, for this interesting contribution. I would like to add here that I have noticed a similar effect with straight copper. There is, of course, the possibility that this maximum in hardness and tensile strength may be caused by work-hardening.

Jan 1, 1945

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006