Search Documents

By Cyril S. Taylor, Junius D. Edwards

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Junius D. Edwards, Cyril S. Taylor

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By J. B. Nau

A short time ago some interesting experiments concerning a new steel-making process in the open-hearth furnace were made by the writer at the Croton magnetic mine, N. Y.

Jan 1, 1892

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By John B. Pearse

In view of the great importance of accurate knowledge respecting the chemistry of iron and steel, as related to their physical properties, I come before you with a paper showing the great mass of work which has been heretofore done on the subject. I have tabulated the more important data I bring at this time, so as to draw out the results clearly. This information is accessible to all who will seek for it. I have made it the basis of my own practice throughout, and such knowledge is undoubtedly the only foundation for the successful practice of metallurgy. As is well known the ordnance corps of our army, after 1841, made exhaustive experiments on the properties of cast-iron. The investigations were undertaken in order to obtain necessary information on the reorganization of the corps. I wish to call your attention to the results obtained by a comparison of the chemical and physical properties of cast-iron for guns, to describe certain characteristic peculiarities of steel, and to give a brief history of the chemical work relating to carbon in iron. The Reports on Experiments on the Strength and other Properties of Metals for Cannon, published by H. Carey Baird, Philadelphia,

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By P. Barnes

Exact accounts hare been kept of the cost of these chimneys, and it may he a matter of some possible interest. that the plans and details of cost should be laid before the Institute. The statement of cost herewith submitted does not give minute particulars of the weights or quantities of material used, although these are noted upon the company's books.

By Guy R. Johnson

In view of the attention now directed to the development of the iron-ores of Virginia, and of the frequent reference in the Transactions of the Institute to the Longdale mines, it is presumed that a brief account of the methods of working and surveying these mines will be of interest. For a better understanding of such a description, a few words will be said concerning the geological character of the ore-deposit. Professor Rogers says in his preliminary report of 1835, that this deposit has " more of the character of a true vein than is usually

Jan 1, 1892

By J. E. Johnson

The general construction of blast-furnaces has undergone no radical change in more than a generation. When the old style of masonry construction was replaced by the steel shell, the masonry piers were simultaneously replaced by columns, never lese than 6 and frequently 12 or 16 in number, set under the mantle-ring. These columns were at first unvaryingly made of cast-iron, but in more recent years have frequently been made of structural steel. The furnace itself has recently been the subject of radical changes; in some cases the thin-lined construction has been adopted for the whole furnace, and in other cases it has been adopted for a zone immediately above the bosh, raising the mantle several feet to make this possible, but still the style of construction with columns set immediately under the mantle has been universally followed. In spite of the apparent fixity of this type of construction it is open to grave disadvantages from the operating point of view, which may be briefly outlined as follows: The slope of the bosh and size of the crucible are such as to leave scant room inside the columns for the necessary water-piping, etc. The bustle-pipe must necessarily be outside the columns and the penstocks have to pass between them, with the result that the columns are frequently much in the way when changing the tuyeres or otherwise handling the penstocks. Moreover, the hearth-jacket requires a diameter but little smaller than the circle of the inside of the columns, and as a result the cooling-water ditch for protection against breakouts is exceedingly limited in width. As a consequence of these conditions, when any work requires to be done around the furnace, such as changing a tuyere or working on the cooling-water pipes, the amount of room left between the columns, pen-

Jan 1, 1913

By G. A. Reinhardt, Albert Sauveur

Although many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel; that is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes marten-sitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line MO—and it remains martensitic or austenitic after slow (air) cooling.' We have in this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening; Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it

Jan 1, 1913

By A. Eilers

The use of the bag-house for filtering out fumes produced in certain metallurgical operations is not new in America. There are no patents in force at this time, to my knowledge, which might hinder such use. Up to about 25 years ago the bag-house was only employed in connection with either zinc-works, which produced the oxides, to be sold for paint, or as an auxiliary in extracting lead from high-grade oxidized ores and from galena-concentrates in the Missouri and neighboring lead-regions; this work being then done in the Scotch or American hearths and in very low slag-furnaces, in all of which was produced an excessive amount of oxides which were also finally sold as paints. The literature1 on the above is abundant in text-books and periodical publications. The first large bag-house to be used permanently in connection with lead blast-furnaces was erected, as far as I am aware, about 1887 at the Globe smelting Co.'s works at Denver, Colo., under the Lewis-Bartlett patents. The brick flue, running from the blast-furnaces to the bag-house, was only a few

Jan 1, 1913

By Henry M. Rowe

Professor Ruff's most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the liues B'D'lII represent the experimental results reached by Ruff and Goecke;a AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data; S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin;5 GS the line A3 after Ooerens and Meyer; 6 and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightiiess and its sharp inflection near 6.67 per cent. of carbon, the carbon content of

Jan 1, 1913

By Bradley Stoughton

[Secretary's Note.—TO avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.—J. S. 1 Introduction. This paper gives the results: first,, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castr ings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows : 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such 'as, for example, the wear of railroad-rails, of steel and chilled-iron rolls, car-wheels, etc. 2. These improvemerits seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example: A series of tests on cast-iron

Jan 1, 1913

By N. E. Maccallum

Almost half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: aWhat is the safe and economical limit of the open-hearth furnace ?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Go., of Phœnixville, Pa., and their distinctive and important feature is, that they charge to twice the capacitl of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Jan 1, 1913

By William Glenn

The taking of proper samples of crude ores seems to he less thoroughly understood, or less carefully practiced, than its impor tance requires. We all know how often we encounter the reports of very accurate assays and analyses, the weight of which as evidence wholly depends on the method of obtaining the sample, and is very probably nil, because there has been no proper sampling. Pissages might be cited from technical books, and from current technical literature (all the work of writers whom we delight to honor) to show that even among high scientific authorities there is too little acquaintance with the practical art of the sampler. There is no metallurgical or chemical establishment which does not frequently receive samples truly representing nothing. They consist usually of bits of ore, or what not, selected because they are worse or better than the average of what they are meant to represent. And they are worthless, no matter who made the selection. Where conscious choice is permitted to enter into the operation, a fair sample will not result, unless by a miracle. The work of sampling is often looked upon as within the realm of boys and of pensioners only. At least, though the manual labor be left to subordinates, the principles on which it is conducted and the safeguards with which it is surrounded are not unworthy of the study of experts; and experts should he ready to teach these principles and enforce them in practice. For exact sampling is the indispensable first step towards learning the value of any boxful, carload or shipload of ore. I propose to give a simple account of the method of sampling by hand, such as I have always pursued. There is nothing new about it. So far as I know, it is the immemorial old method, as old at least as Cornish copper-mining. Perhaps my fellow-members in the Institute may suggest improvements in it. If not, it will constitute a record in our Transactions to which laymen and beginners may be referred.

Jan 1, 1892

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By James W. Neill

Bituminous coal has for many years been used for the smelting of iron-ores in the blast-furnace. In some districts in Scotland it is used alone, in others it is used mixed with coke. The similar use of certain bituminous coals in the United States has been repeatedly mentioned in the Transactions. (See, for instance, as to the Hocking Valley coal, the papers of Dr. T. Sterry Hunt, Trans., ii., 275, and vii., 313; and as to Indiana "block-coal," the paper of Mr. J. S. Alexander, Trans., i., 225.) Phillips (Elements of Metallurgy, p. 250) says: " Raw coal for blast-furnace use must be of a non-cokiog kind, and, when of suitable quality, is perhaps the most advantageous fuel." In the first

Jan 1, 1892