Search Documents

By B. V. Knelson

Although the concept of centrifugal recovery has been around in one form or another for many years, it has not been until recent times that it has became clearly understood am properly put into perspective. Simplistic in theory, it is when one begins to examine the variables involved that the true complexities of this matter begin to emerge. In creating an enhanced g force concentrator, there are many aspects both positive and negative that are encountered.

Jan 1, 1989

By B. V. Knelson

"GENTLEMEN:This paper will deal with centrifugal separation - theory and practical, and since the Knelson Concentrator is the only centrifugal concentrator with a properly fluidized bed, this paper will cover the Knelson Concentrator and its technical and structural advances over the last five years. As I am the person with the most experience in this line, I guess I am some kind of an expert; what kind I’m not sure, but some kind.This type of concentrator truly was developed because I’m lazy and I constantly look for easier ways to do things. My experience in the mining industry was very limited but I did realize in looking at placer operations, which is the application where I spring from, that it was tremendously labour intensive and my first reaction that ""my god, there must be some method or way-of handling product in a more efficient (and you can read that as being able to quickly recover very fine particle gold) way than was being shown at that time"". So, the Knelson Concentrator was born - about 6 or 7 years later. Our first attempt was a cone with about the same degree of slope as our present machine and since we had no knowledge of vibration dampening and centrifugal forces at that point, it was just an idea that this should work.Our first run was one of twenty minute duration. We did make that first machine variable speed by a mechanical belt system and we found that at about 240 rpms we were virtually shaking the gravel plant apart that we were attached to. So the first run was twenty minutes and back to the drawing board. However, that first run produced a concentrate so superior to anything we had seen previously, that we knew without any question, we were definately and accurately on the right track."

Jan 1, 1985

By E. Costa Silva

Among the methods of mineral processing, gravity concentration methods are, probably, those which have lower costs, higher capacities and lower operational complexity. In order to be really effective, these methods require a feed size distribution in which the particles are liberated. Further, there must be a significant difference (usually higher than 1-1.5) among the real densities of the particles. However, in most cases, the traditional gravity concentrators (jigs, shaking tables, spirals and dense medium hydrocyclones) lose efficiency (sharpness of cut and recovery) when the mean diameter of particles are lower than 0.05mm and the difference among densities are smaller than 1. Most gravity concentrators developed in the last 20 years are based on the use of centrifugal forces that create large "apparent gravitational gradient" seeking to overcome the limitations of particles size distribution. This paper presents the experience of the CVRD Research Center in evaluation and development of new process based on using this new generation of gravity concentrators.

Jan 1, 1999

By W. W. Wen

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen- bowl centrifuge for the dewatering and reconstitution of column flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine-clean-coal slurry from the column flotation concentrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free-flowing granular form, while the untreated products were wet, sticky, and difficult to handle. Specifically, test results indicated that the average moisture contents of the dewatered coal were 35.7, 35.5, 32.6, 29.9, and 26.5 wt% with Orimulsion additions of 0,0.7,3.2,4.8, and 6.4 wt%, respectively. The handleability and dust reduction of the dewatered coal product were also vastly improved.

Jan 1, 1997

By R. H. Weiland

The dewatering of flocculated clay suspensions by compression in a centrifugal field has been investigated. The results are evaluated with regard to both direct applicability to centrifugal dewatering, in solid-bowl centrifuges for example, and indirect applications to gravity sedimentation systems. It is well known that sediment consolidation under gravity depends on structural characteristics such as permeability and on the "self-weight" of overlying sediment layers. An important objective of the study has been to evaluate the self-weight effect using centrifugal forces to simulate consolidation in deep sediments. In this way, small-scale laboratory tests can be used to predict the rates and limits of sediment compression in industrial systems such as thickeners and settling ponds. Experiments have been conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The effects of initial structure have also been studied using controlled variations in flocculation conditions.

Jan 1, 1993

By T. Xu

"The CTL-500 centrifugal extraction machine, which was independently developed by Baotou Shibo Rare Earth Extraction & Equipment Co., Ltd., is presented in this article. The machine is based on centrifugal extraction principle and has been used in P507-HCl-RECl3 extraction system. Automatic control has been utilized in the system. In this paper, a comparison is made between centrifugal extraction and conventional mixer-settler extraction and satisfactory results are shown. INTRODUCTIONCentrifugal extraction is a fast and efficient liquid-liquid extraction method. The process includes solute transfer and separation of the two liquid phases. In the CTL-500 machine, the organic and aqueous phases individually enter a lower mixing chamber in certain proportions and are mixed and dispersed and solute thereby transferred from one phase to the other. The mixed phases pass into a rotating drum and the two liquid phases are separated under centrifugal force. As it flows upward, the aqueous phase, which has a higher specific gravity, flows away from the rotating drum centre towards the drum wall and the organic phase flows towards the drum center. The two liquid phases enter into collection chambers through independent weir plates and are discharged from the machine.The centrifugal extraction machine has been widely used in liquid-liquid separation, either without solid or with small quantities of solids (Chen, Zhang, Zhuo, Chen & Li, 2008; Duan, Jing, Zhu & Chen, 2007; Duan, Zhou & Zhou, 2006). Examples of the use of the centrifugal contactor include the separation of water from crude oil, treatment of heavy oil and diesel to eliminate water and salt; the extraction of penicillin, garlic oil, malathion, and interferon; the hydrometallurgy recovery of nickel, copper and uranium; extraction of edible oil, spice, refined oil and food color; treatment and recycle of print and dyeing wastes; treatment of hydroxybenzene-contaminated sewage by multistage extraction and separation of water from oil in ship sewage."

Jan 1, 2012

By Bothe C

Froth flotation processes use different surface properties of the minerals to be sorted. In an aqueous environment the hydrophobic mineral attaches selectively to air bubbles and is lifted to the surface of a separation vessel, while the tailings settle towards its bottom. Besides the surface properties, the hydrodynamic conditions play an important role. With respect to the hydrodynamics the flotation process can be divided, for simplicity, in two sub-processes. The attachment of hydrophobic particles to air bubbles, the so-called mineralisation, demands a large number of collisions and therefore high turbulences. The phase separation however needs a deterministic movement of both the particle-bubbles-aggregates and the tailings particles and therefore a quiescent flow field. The optimisation of the overall process requires a separation of both sub-processes, especially when fine particles have to be sorted. In conventional mechanically agitated flotation cells both sub-processes take place in the same turbulent volume. For this reason they suffer from a decreasing selectivity with decreasing particle size. In flotation columns the mineralisation of air bubbles and the phase separation are performed in a quiescent environment. This results in high concentrate grades and at the same time in a very slow attachment kinetics, which must, especially for fine particles, be counterbalanced by a long residence time of the slurry.

Jan 1, 1993

By H. EI-shall

Bench top centrifuge is used to study the consolidation behavior of phosphatic clays. A mathematical model (based on first order kinetics) is developed to describe the relationship between the void ratio (at any time) and the effective stress. Permeability of the sediment as a function of the void ratio is also described. The obtained data are compared with that obtained by other consolidation testing methods. Centrifuge results indicate that consolidation data may be developed in a short period of time (hours) as compared to days or weeks when other techniques are used.

Jan 1, 1995

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

By R. P. Killmeyer, W. W. Wen, B. K. Parekh

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen-bowl centrifuge for the dewatering and reconstitution of column -flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine clean-coal slurry from the column flotation con¬centrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free flowing granularform, while the untreated products were wet, sticky and difficult to handle. Test results indicated that the average moisture contents of the dewatered coal products were 35.7%, 35.5%, 32.6%, 29.9% and 26.5% (by weight) with Orimulsion additions of 0.0%, 0.7%, 3.2%, 4.8% and 6.4% (by weight), respectively. The handleability and dust reduction of the dewatered coal products were also vastly improved.

Jan 1, 2000

By L. S. Rubin

The efficient and acceptable disposal of fine coal refuse (28MxO) is one of the highest priority problems facing the coal industry today. For many years the established system for the disposal of this fine refuse slurry has been to concentrate the solids in a static thickener and pump the resulting 20-40% solids underflow to lagoons or impoundments. Although this technique has served the coal industry well, increasing environmental concerns and refuse related disasters, such as Buffalo Creek, West Virginia and Aberfan, Wales, Great Britain have resulted in federal and state regulations which now control fine refuse disposal methods. As a consequence of these regulations, the capital costs of constructing, maintaining, and operating regulatory complying impoundments has become in many cases economically unattractive. Areas processing topologies similar to those coal preparation plants of the Appalachians are particularly burdened by these regulations and are consequently turning to alternatives for handling and disposal of their fine coal refuse. The basic requirements of impoundment alternatives as defined by environmental and plant demands are: (1) A relatively solids-free liquid (1000 ppm or less) to serve as plant make-up water in a "closed circuit" system, and (2) a sufficiently dewatered solids product which can be combined with the coarse refuse to form a compactable stable land-fill.

Jan 1, 1978

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By John S. McCartney, Ismaail Ghaaowd

This study presents the results from centrifuge modeling experiments performed to understand the effects of temperature changes on the pullout capacity of scale-model energy piles embedded in normally- consolidated clay layers. The energy pile under investigation is an aluminum cylinder instrumented with internal strain gages and thermocouples, and its temperature is controlled using an internal electrical resistance heater. The energy pile was first heated until the temperature, pore water pressure, and volume change of the surrounding clay layer stabilized, after which the energy pile was cooled. Pullout tests were then performed on the energy piles heated to different temperatures to understand the effects of the preceding heating-cooling cycle on the pullout capacity. In addition, the clay undrained shear strength profiles were measured using push-pull T-bar penetration tests before and after heating. INTRODUCTION When a heat source such as an energy pile is embedded in a saturated clay layer, temperature changes will result in changes in pore water pressure as the rate of heating is typically faster than the rate of pore water drainage (Campanella & Mitchell 1968, Abuel-Naga et al. 2007, and Ghaaowd et al. 2016). Although all soils will initially expand during undrained heating, normally consolidated soils typically exhibit permanent contraction while overconsolidated soils exhibit expansion after sustained heating when drainage is allowed (Vega & McCartney 2015). Subsequent drained cooling typically leads to elastic contraction. Thermally- induced changes in pore water pressure and volume during transient heating and cooling may affect the soil- structure interaction of energy piles, as well as the ultimate capacity of the energy pile. This study is relevant as relatively few studies have been performed on the behavior of energy piles in soft clay (e.g., Ng et al. 2014), with most focused on the behavior of drilled shaft energy piles in stiff rock or overconsolidated clays (e.g., Laloui et al. 2006; Murphy et al. 2015; Wang et al. 2015; McCartney and Murphy 2017).

Jan 1, 2018

By J. Gniel, L. King, C. Gaudin, C. O’Loughlin

"This paper presents some recent advancements in centrifuge modelling, which enable the installation of displacement piles to be performed in-flight while measuring ground responses. Details and results are provided from a series of experiments where 21 full-displacement piles were installed into a sample of consolidated kaolin clay at 40g. The piles were pushed into the sample at a constant rate of penetration, with installation reaction loads and pore pressures measured. Insight into the installation effects of the full-displacement piles was obtained by undertaking in-situ testing pre- and postinstallation of piles. The findings show that centrifuge testing has the potential to play an important role in furthering the current understanding of displacement pile behaviour and installation effects.INTRODUCTIONDisplacement piles and displacement ground improvement columns cause soil to undergo significant distortion and shearing during installation, which alters the soil properties. It is essential to consider these changes in soil properties to estimate the behaviour of pile foundations with higher degree of accuracy. However, the installation effects of displacement piles are widely considered as one of the most difficult geotechnical mechanisms to model, both analytically and numerically, and experimental data is needed to advance the current state of knowledge.Theories, analytical and semi-analytical, have been developed to describe the displacement pile installation process. Randolph et al. (1979) applied the cylindrical Cavity Expansion Method (CEM) to model the installation of a displacement pile in a fine grained cohesive soil. However, cylindrical CEM only considers the field variables in radial coordinates, and hence the soil-pile interface can only be modelled as a frictionless material. Baligh (1985) introduced the Strain Path Method (SPM), which assumes soil flows around the tip of a displacement pile. SPM was shown to model the stress and strain fields, particularly within close proximity to the pile, more accurately compared to the cylindrical CEM. While these methods account for the installation effects of a displacement pile and can be used to estimate a resulting ultimate bearing capacity, they are unable to describe the load-settlement behaviour of such piles. With the added complexity of group effects, existing analytical methods do not provide a means to accurately calculate the ground response to the installation of a group of displacement piles in a cohesive soil.The advancement of computational power, numerical techniques and constitutive models has improved the accuracy of numerical analysis, particularly in regard to modelling pile installation. However, even with advanced techniques, Finite Element Method (FEM) suffers a number of disadvantages due to the large deformations, which results in mesh distortion and tangling. Mesh-free methods such as Discrete Element Method (DEM), Smoothed Particle Hydrodynamics (SPH) and Material Point Method (MPM) are the next generation of computational techniques that are able to deal with large deformation problems. However, these advanced techniques are computationally expensive, complex and yet to be incorporated into commercial packages. Such methods are considered to still be in the development stage and are yet to provide a complete solution to pile installation problems."

Jan 1, 1900

By M. J. DeJong, R. J. Mair, S. Ritter, G. Giardina

"For urban tunneling projects it is essential to predict and prevent building damage. Although various case studies and experiments have shown that buildings considerably modify greenfield soil movements, widely accepted damage assessment methods neglect this soil-structure interaction and simplify structures as linear elastic beams. This paper summarizes an experimental investigation of the response of more realistic structures to tunneling-induced deformations. Small scale structural models with façade openings and brittle material properties were 3D printed and tested in a geotechnical centrifuge. Soil and structure displacement data were obtained by image-based measurement. Results demonstrate that structures notably mitigate differential greenfield ground displacements. It is also shown that maximum soil settlements, horizontal soil displacements beneath the structure and structural damage in the form of cracking significantly depend on the position of the structure in the settlement profile. The results provide a basis from which to predict building settlement response with greater certainty. INTRODUCTION With continuing population growth and increasing urbanization expected in the next decades, there is an urgent need for a next generation of infrastructure. It is likely that a large part of this infrastructure will be underground. Such creation of urban underground space frequently involves the excavation of shallow tunnels in close proximity to existing structures and utilities. For example, along the Crossrail project in London more than 1,200 structures are located within a possible influence area of the tunnel construction (Torp-Petersen and Black 2001). The assessment of building damage plays a vital role throughout the planning, design and construction stage of urban tunneling projects. However, while predictions of tunneling-induced deformations in the greenfield can generally be made with some confidence, much uncertainty exists about how structures interact with ground movements arising from tunnel construction."

Jan 1, 2016

By Shinji Sassa, Naoki Takahashi, Eiji Kohama, Wakaki Tsuda, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Abstract Deep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. Column-type solidification, however, has been thought to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil between the columns cannot be reduced. In recent years, experimental results have been reported that imply that solidified columns can reduce the shear deformation of unimproved soil around them. A new arrangement has been proposed to mitigate lateral flow induced by liquefaction. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of stabilized columns. The results indicate that stabilized columns can reduce the lateral flow of liquefied ground if the column displacement and the column head rotation are restricted. This paper concludes that it is important to restrict the displacement and the rotation of the column head by surface improvement to mitigate the lateral flow of liquefied ground.INTRODUCTIONDeep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that column-type solidification cannot reduce shear deformation of unimproved soil around columns, because the displacement of a solidified column is less restricted than that of a lattice wall. Column-type solidification has been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that solidified columns have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and column-type solidification. Their results showed that column-type solidification with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new column arrangement shown in Figure 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010). The stabilized columns in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2014

By André R. Laplante

"This presentation reviews three continuous centrifuge separators, the Falcon-C, Kelsey Jig and Multi-Gravity Separator, two units with possible synergies with centrifuges, the In-Line Pressure Jig and InLine Leach Reactor, and two centrifuge prototypes, the continuous Knelson and the Altair Jig. Typical applications, potential problems, promising synergies and general concentration mechanisms are discussed. A general discussion on the sources of information, the nature of the fluidization water flow, test work for potential centrifuge separations and the early life cycle of new technology, using centrifuge separators as an example, follows. ResumeCette présentation fait le point sur trois appareils de séparation centrifuge, le Falcon-C, bac oscillant Kelsey et Multi-Gravity Separator; deux appareils qui présentent des synergies possibles avec les centrifuges, le bac oscillant In-Line Pressure Jig et le système InLine Leach Reactor; et deux prototypes centrifuges, le Knelson continu et le bac oscillant Altair. On y présente des applications typiques, les problèmes d’opération les plus usuels, les synergies les plus intéressantes. On discute également des sources d’information disponibles pour le minérallurgiste, de l’impact du mode d’ addition de l’eau de fluidisation, de la démarche expérimentale a faire avant d’installer un centrifuge, et du cycle de développement de nouveaux équipements, en utilisant les centrifuges comme exemple.IntroductionGravity separation has undergone a renewal in the past 20 years, much of it attributed to centrifuge units. The semi-batch Knelson Concentrator has probably received the most exposure, but it is rather because of the shear number of units sold than the width and breath of its applicability. It excels at recovery very dense minerals in very small concentrations, and has become a workhorse of the gold industry. Falcon’s Super-Bowl comes a distant second, with very similar applications. A number of copycats are available, and are generically identified as “Knelsons.” This presentation will not address these units explicitly, but as possible synergies."

Jan 1, 2000

By Will Medina, Carlos Gonzáles, Ángel Navarro

Hoy en día, muchas empresas no tienen una comprensión clara de la línea de base de las emisiones de gases que producen hoy y cuál es su perfil de uso de energía. Aquellos que lo hacen a menudo usan hojas de cálculo que consumen mucho tiempo para compilar y son propensas a errores humanos. Además, es evidente que la actividad minera y la producción de metales, tal como se lleva a cabo en la actualidad, generan emisiones de carbono significativas. Esto pone de manifiesto la necesidad urgente de abordar este problema y adoptar medidas efectivas para reducir la huella de carbono de la industria minera.

Sep 29, 2023

By Violeta Vigo Vargas

El Centro de Innovación Tecnológica en Joyería “Koriwasi”, CITE Joyería Koriwasi, es el resultado de una alianza estratégica entre Minera Yanacocha (Asociación Los Andes de Cajamarca) y el Estado (MINCETUR). El proyecto se ejecutó hace cinco años y busca mejorar las capacidades técnicas y las condiciones tecnológicas del proceso productivo del artesano joyero mediante la implementación de una institución prestadora de servicios especializados. En ese sentido, el presente texto describe los objetivos estratégicos de dicha empresa para mejorar permanentemente las capacidades técnicas del artesano joyero en función a estándares internacionales y apoyar el proceso de producción individual del artesano joyero, mediante la facilitación de materiales procesados garantizados y la prestación de servicios de maquinado de calidad, así como desarrollar un sistema de información que promueva la articulación entre la red de artesanos joyeros y el mercado nacional e internacional.

Sep 14, 2009

By Mario Samamé Boggio

El presente texto señala los antecedentes históricos, diversificación, energía eléctrica, y geología del distrito minero más grande de CENTROMINPERÚ, Cerro de Pasco. Así también se describe los yacimientos minerales de la mina como son: Morococha, Casapalca, Yauricocha, San Cristóbal Cobriza y la fundición de la Oroya.

Jan 1, 1974