Search Documents

By G York

South African gold reserves extend to great depths. However, strategies for the mining of such deposits have changed only slightly over the past number of years. Regional support at depth is currently provided by rock pillars and backfill. Many problems have been experienced with these regional support practices at deeper levels. In this paper several alternative forms of regional support are described which include the use of concrete, the use of back area caving and confinement to strengthen pillars. These new concepts are supported by numerical and laboratory modelling and in situ results.

Jan 1, 1998

By L. H. Van Loon, E. G. Crayston, A. F. Heather

"IntroductionTHE PROPERTY of Madsen Red Lake Gold Mines. Limited. comprises fifty-eight claims located between Russet and Faulkenham lakes in Baird and Heyson townships of the Patricia portion of the District of Kenora. The mine is seven miles •by road from the hamlet of Red Lake. This latter centre is .connected to the Trans-Canada Highway at Vermillion Bay, Ontario, by provincial highway No. 105 which has a total length of one hundred and thirteen miles.The Madsen property went into production on August 11th, 1938, with a milling plant rated at 300 tons per twenty-four hours. Changes made in the crushing plant during October, 1938, allowed a •finer feed to be delivered to the mill and increased the milling •capacity to 400 tons per twenty-four hours. During 1948, steps were taken to add an additional 400-ton capacity unit to the milling plant. This latter work was completed by May, 1949, giving the present total milling .capacity of 800 tons per twenty-four hours.It was realized in the early 1940's that, eventually, considerable material suitable for backfilling in the mine would be required. As there were no large deposits of gravel or sand anywhere near the mine, officials of the Company considered it advisable to investigate the feasibility of using mill tailings for mine •backfill. Since Madsen mill tailings contain approximately 80 per •cent of minus-200-mesh material, it was not considered practical to use them for underground backfill without first removing the finer material. as the slimes present in a product of this fineness would without doubt preclude any drainage whatsoever. Table I gives a sizing analysis of Madsen mill tailings and Table II a quantitative chemical analysis of the ore."

Jan 1, 1954

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003

By Jamel Sgaoula

During 1998 COGEMA Resources Inc. announced that operations at the Cluff Lake mine will be suspended indefinitely by the end of year 2000 as a result of deteriorating uranium market conditions. To remain profitable, Cluff Lake mine started an aggressive cost reduction program. A cost reduction team was formed to look for ways to lower production costs. The focus of this team was to screen all areas and to come up with ideas to improve the economy of the mine and ensure the viability of the operations over the remaining three years of operations. Among the areas where significant savings were achieved are: (1) replacement of portion of cement with fly ash in backfill; (2) backfill optimization; and (3) new shotcrete plant installation on site for bulk in-house shotcrete production. This paper details the research work carried out by Cluff Lake mine on these projects and results of its application.

May 1, 2001

By T. R. Yu, D. B. Counter

"Kidd Creek Mines primarily employs sublevel blasthole stoping for underground mining operations. During pillar recovery in No.1 Mine and panel mining in No.2 Mine, the free standing fill exposures may reach a height of 100 m or more. Consequently, a competent consolidated rockfill has been required to fill the mined openings.Since 1976, a total of more than fifty stopes and pillars have been filled with over four million tonnes of backfill. Fill exposures, up to heights of 100 m, have stood up well after blasting adjacent to the backfill.The fill material consists of a graded aggregate, Portland cement and ground slag. Sand has been occasionally mixed in the fill material to serve as avoid filler. The aggregate is prepared in a fill crushing plant, transported underground through raises, and hauled to the filling stopes by conveyors in No. 1 Mine and by trucks in No.2 Mine.Two mixing methods are currently in use. No. I Mine utilizes the free fall of gravity; the fill materials are sprayed with cement slurry as the aggregate departs from the conveyor into a mixing culvert. The other is the use of a rotary mixer on a batch basis in No. 2 Mine.This paper describes the fill systems, filling operation s, and the backfill quality control practice, together with various testing results related to improving fill quality as well as reducing fill costs.IntroductionThe Kidd Creek minesite, located 27 km north o f the city centre of Timmins, Ontario, produces 4.5 million tonnes of copper, zinc, lead, and silver ores annually from its No. 1 and No.2 underground mining operations. Both mines employ a sublevel blasthole stoping method."

Jan 1, 1983

By Ike Isagon

Backfilling has become an integral process in underground mining operations, with varying cost-effective forms of application. This study is a part of an overall investigation into the backfill practices at Copper Cliff North Mine (CCNM). The mine is well-diversified in terms of backfill methodologies and practices. The mine employs different fill methods such as cemented and un-cemented rock fill, slag fill, and cemented hydraulic fill (or a combination of them) in order to fill the voids created by mining activities. The history of backfilling at CCNM has been dominated by cemented and un-cemented slag fill. Each fill method requires operating and engineering guidelines for a cost effective quality control system. The purpose of this paper is to briefly discuss the backfill methods and applications, operating guidelines, and engineering requirements at CCNM.

May 1, 2011

By H. A. D. Kirsten

The assessment of backfill as a support medium in gold mines has been based generally on its ability to reduce the amount of potential energy available to cause damaging rockbursts. While this regional support effect is very important, the methods of analysis commonly used to quantify it predict that, owing to the very compressible nature of the fill, the support provided in areas of small convergence will be negligible. This prediction, however, is contrary to the conditions observed in practice, namely that weak fill does provide a discernible beneficial effect. In addition to the regional support effect, several mechanisms of secondary support, particularly those applicable to areas of low convergence, are identified and discussed. These include the mechanism of deformation of the detached hangingwall beam, rotational and shear effects on bedding, joints and fractures, joint infill, the continuous support effect of the backfill under static and dynamic conditions, the preservation of the integrity of the hangingwall beam, and the potential modification of local stress fields. Confidence in the validity of some of these mechanisms is afforded by the results of theoretical investigations into the behaviour of backfill- supported stopes. The results dealt with are: ? the behaviour of the hangingwall as a beam on an elastic foundation; ? the behaviour of stope/backfill, modelling the surrounding rock as a jointed rock mass.

Jan 1, 1988

By L Neindorf

The development and application of paste fill, cement slurry aggregate fill and shotcrete bulkheads at Mount Isa Mines is described. The progressive changes in filling style in the Mount Isa copper mines from a dry fill based cemented rock fill to tailings based paste fill and slurry fills is explained. The development of shotcrete arched bulkheads and engineered drainage system is described. Details on how Mount Isa Mines has achieved approximately 30 per cent cost reduction in backfill operations through innovations are given. The development of a rocky paste fill is explained.

Jan 1, 2005

By D Morrison

Backfill is usually considered a necessary evil that contributes little to the principal objective of the operation, ore production. Consequently, it is relegated to an auxiliary role in the operation with minimal equipment and resource allocation in planning and is only superficially considered during feasibility studies. In many mines, the inadequacy of the design and operation of the backfill system ultimately leads to frequent delays, excessive costs and, in the worst cases, major instabilities which result in reduced ore production and lost or unrecoverable ore reserves. The primary objective of backfill is to prevent the progressive deterioration of mined out excavations. With the exception of narrow vein operations, it is too weak to alter the mining induced stress regime and control stress concentrations caused by stope extractions. However, the direct benefits of backfill include the possibility to consider a wider range of mining methods, recovery of 100 per cent of the planned resource and the selection of a stoping sequence that minimises the regional stability problems that cause production shortfalls in the later years of mine production. Indirectly, backfill is a practical means of solving other issues, such as waste disposal, that impact the viability of mining. In Australia, the geotechnical conditions of many mines are becoming more difficult and increased attention to the importance of backfill is warranted. This paper describes realistic aspects of backfilling and the positive impacts a well co-ordinated fill system can have on mining activities as a whole. Examples are presented where an integrated approach to backfill systems have offered significant benefits to the operation.

Jan 1, 1998

By C Linklater, J Chapman, A Watson

Closure options under consideration at some sites include backfilling mined-out pits with waste rock. Backfill may include mineralised and non-mineralised waste rock. Following groundwater rebound, flow-through conditions may develop in the pit post-closure. The backfill located in the saturated zone below the water table may release solutes under such conditions. It is therefore important to understand the potential impacts that backfilled pits could have on postclosure groundwater quality.Geochemical characterisation programs are the foundation for assessing the potential chemistry of water that has contacted mined wastes. Such programs must be designed to obtain data relevant to the closure options under consideration. To complement standard testing techniques, SRK utilises saturated column testing designed to generate data on leaching rates under anoxic conditions that could be encountered within submerged backfill.This paper presents the findings of saturated column test work carried out on waste rock samples from an iron ore mine in the Pilbara.CITATION:Watson, A, Linklater, C and Chapman, J, 2016. Backfilled pits – laboratory-scale tests for assessing impacts on groundwater quality, in Proceedings Life-of-Mine 2016 Conference , pp 110–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999

By Michael K. Rhodes

A 120 tonne per day BacTech bacterial oxidation plant treating refractory gold concentrates for Gold Mines of Australia's Youanmi project in Western Australia commenced operation September 1994. This was the first commercial application of the BacTech process. A pilot plant trial on concentrates produced from Youanmi ore was carried out at BacTech's laboratory in Perth. Results and measurements from this trial were used by Signet Engineering Pty Ltd to design the commercial plant. This paper cover the results obtained from the piloting, their implementation in the plant design and the initial commissioning of the full scale plant.

Jan 1, 1995

By John W. M. Lambert

This paper describes the execution and the results of a new method to seal off leaks in water retaining constructions. The new method, called BioSealing is based on activating the bacteries, present in soil and groundwater. The method was tested under field conditions in 2004 and applied at the HSL aqueduct of the 'Ringvaart Haarlemmermeer' in 2005.

Jan 1, 2006