Search Documents

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By D. G. Krige

D. G. Krige: The stimulating contributions from Messrs Cooke, Curtis, Martus, Johnston, Van Wyk, Van Rensburg and Wroth are appreciated by the author and provide clear evidence of the importance not only of the principle of assistance to gold mines, but also of its scope and form. In general all the arguments, raised by Messrs Cooke, Martus and Johnston in favour of extending the scope of the new assistance scheme can be accepted as sound.

Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley's plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald's contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.

Discussion of the paper of R. J. COLONY, presented at the New York Meeting, February, 1921, and issued With MINING AND METALLURGY No. 169, January, 1921. R. J. COLONY (author's reply to discussion).-The work of Sosman and Merwin on the system lime-ferric oxide, mentioned by Mr. Rankin, was not overlooked. When studying portland cements and portland-cement clinkers petrographically, however, the lime-iron compound was difficult to correlate with the very definite dicalcium ferrite described by those investigators, which possesses such well-defined optical properties. In portland cements, the calcium ferrite (or ferrate?) is an indefinite, fuzzy, and generally amorphous, or apparently amorphous substance that is distributed interstitially with respect to the other grains, from which it was very difficult to derive any satisfactory results. For this reason, the writer, tentatively, chose to regard it as related to the aluminate, and assigned to it the composition 3CaO.Fe203, which may be incorrect, however, as Mr. Rankin suggests.

Jan 8, 1921

By H. Arima, Y. Kudo

In general, the iron content of zinc leach residue produced by sulphuric acid leaching from calcine is disposed as jarosite or goethite into a tailing dam. More recently, these iron residues have been treated pyrometallurgically to avoid waste disposal. The Iijima refinery selected a different zinc leach residue treatment process for iron control when it was established in 1971. The Iijima refinery is the only plant in the world that has processed a zinc leach residue by the combination of SO2 pressure leaching and O2 pressure hematite precipitation. The process enhances zinc recovery and recovers gold, silver, copper, lead and rare metals in saleable by-products. This paper focuses on the two stages of autoclave application in the zinc leach residue treatment process. The detailed flowsheet and recent advancements to improve the quality of by-products are discussed.

Jan 1, 2004

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By I. Farr, M. R. Mock, J. C. Robison

"HPAL and POX autoclave vapor-space gasses are vented through an autoclave PCV (Pressure Control Valve). The downstream steam-born mist of liquid droplets and solid particles travels in excess of 1000 m/s with megawatts of kinetic power at temperatures up to 160 C. The characteristics of downstream states often result in problems with corrosion, erosion, noise and vibration. Comprehension of those and related characteristics aids in improved pressure control, overpressure control and autoclave level control. We introduce compressible multiphase flow concepts and constructs germane to such flow including choked flow, continuous phase change, shock waves and supersonic flow plumes. Flow modeling based on first principles quantitatively predicts such flows providing a tool for component sizing and a method to estimate effects of water injection on flow. Insight deduced from modeling aids in mitigation of afore mentioned problems of which we share some from-site examples.INTRODUCTION First principles related to fluid thermodynamics and compressible flow have been employed akin to their application in the rocket industry. We will present the results of the application of those principles conceptually and authentically without mathematical rigour while using language of the pertinent disciplines. The autoclave (AC) vapor space over the slurry of a POX (Pressure Oxidation) or HPAL (High-Pressure Acid Leach) system (depicted in Figure 1) is vented via a PCV (pressure control valve) followed by certain ducting, and perhaps a nozzle, before exiting at atmospheric (typically) pressure. As indicated by its name the PCV controls the AC pressure as the flow control component of a pressure control loop."

Jan 1, 2017

By Claudio Acuña, Sergio Romo, Gerardo Fuentes

The leaching kinetics of a zinc concentrate in autoclave reactors were studied. A sample of concentrate from Bolivia, with typical mineralogical characteristics of the Andes region, was used. A concentrate containing 49% zinc and 145 ppm of silver from Minera Viacha was characterized chemically and mineralogically (atomic absorption, X-ray diffraction, and SEM microscopy) and tested in bench scale reactors. Two types of autoclave batch reactors were used at 40 bars of oxygen pressure and three levels of temperature (150°C, 200°C and 250°C). The solid to solution leaching ratio was 1:10 (10% sulphuric acid concentration). The effect of the particle size of the concentrate on the leaching kinetics was studied (P80: 145 and 45 µm). Iron from the leaching solution was removed by precipitation by increasing the pH in order to generate a clean solution for zinc electrowinning. The zinc solution was used to evaluate the feasibility of cathode production at the laboratory scale. Zinc extractions with higher liberation (P80 = 45 µm) reached up to 98%. Ground concentrate with finer sizes resulted in agglomeration and the use of dispersing agents did not improve slurry mixing. The leaching solution contained 55 g/L zinc and 7 g/L iron; it was purified by precipitating iron. The precipitation was evaluated using sodium hydroxide and ammonium hydroxide. In the first case, a colloidal suspension of ferric salts was formed while in the second case, different iron compounds were precipitated. The precipitate obtained with ammonium hydroxide had better filtering properties. Electrowinning was carried out using two types of cathodes (stainless steel and aluminium) and solutions purified with ammonium hydroxide. Zinc cathodes formed on stainless steel presented a better physical quality than those formed on aluminium.

Jan 1, 2015

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By John H. Bassarear

How best to grind? This article compares conventional crushing and grinding circuits to semiautogenous circuits, reviews recent installations of each circuit, and describes seven methods of using autogenous or semiautogenous techniques. In addition, steel and power consumption data are reported and benefits of a dedicated digital computer are discussed. Size reduction is the most expensive operation in most mills. Crushing and grinding are usually the greatest part of capital costs. They often make up 60-70% of total mill operating costs. Picking the proper crushing and grinding method must, therefore, be done with great care, so the best circuit is chosen. In the past 10 years, there has been a strong trend toward using autogenous or semiautogenous grinding in mills throughout the world. Autogenous grinding is favored when the ore is quite competent and a fine grind is needed. Semiautogenous grinding is applied when fine crushing could cause severe problems or when ore varies in hardness or competency. The taconite iron ores of northern Minnesota fit the description for an autogenously ground ore and many are successfully ground that way. Most im¬pressive are the nine lines of 11 x 4.9 m (36 x 16 ft) mills powered by 9 MW (12,000 hp) motors at Hibbing Taconite. Porphyry copper and molybdenum ores fit the description for semiautogenous grinding. Recent installations include Highmont in British Columbia, Canada, and Quintana in New Mexico. Sampling Many mills have been built based on inadequate sampling data or insufficient tests. With the cost of many mills exceeding several hundred million dollars, it is mandatory that geologists, mining engineers, and metallurgists work together to prepare representative testing samples. Simple, repeatable work index tests are usually sufficient for rod and ball mill tests. However, pilot plant tests on 50-100 t (55-110 tons) of ore are frequently necessary for autogenous or semiautogenous mills. Preparation and selection of the test sample is of utmost importance. Procedures for autogenous and semiautogenous mill pilot plant tests are relatively simple for those experienced in running them. Reliable and repeatable results can be obtained if simple, fundamental procedures are followed. The accompanying figure shows a typical conventional crushing-grinding circuit with three stages of crushing followed by ball mills or a rod mill-ball mill combination. This flowsheet is typical of many mills that have been built throughout the world. Also shown is a typical semiautogenous (SAG) circuit with feed coming directly from a primary crusher, and the semiautogenous mill product going to the separation process. Many similar semiautogenous circuits are built today because they are simple and flexible, lend themselves readily to high tonnages, and usually cost less to build and operate. With some ores, it is possible to send mine-run ore directly to the semiautogenous mill, eliminating the need for a primary crusher, as at Benquet's Dizon mill in the Philippines. An autogenous or semiautogenous circuit, as the name implies, uses the ore itself to assist in the grinding process. Generally, for this type of circuit, the ore must be competent so large ore chunks can be used to grind smaller ones. If ore alone is used, then the circuit is autogenous; but if balls are added to supplement the charge, then the circuit is termed semiautogenous. Ore competency is not always a criterion, to break up large pieces and wash away cementing material. Autogenous and semiautogenous mills have been very successful on relatively soft uranium ores where the values are frequently found in the material that cements together the sandstone grains. Autogenous Circuits When an ore is hard and competent, it is always possible it might make good "pebbles" that could be used for fine grinding media. Seven methods have been tried using combinations of autoge-

Jan 6, 1982

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981

By Jr. Jones

This paper is derived from a document that compiles autogenous and semi-autogenous mill installations worldwide, through the end of 2010. Updates have been solicited from all major mill manufacturers and most have responded. A review of AG/SAG mills sold to date and in the last five years indicates that the AG/SAG mill market is very healthy and the trend is larger diameter mills with high diameter-to-length ratios. Ring motors (gearless) are the preferred drives for large mills even though the power transmitted through a gear drive is expected to near 11,000 kW per pinion in the near future.

Jan 1, 2012

By Chen Z, Dong H

This paper describes the autogenous carrier flotation of 0 - 20 ¦m ilmenite using 40 -- 80 }tm ilmenite as carrier. Investigation is made of the influence of main technological parameters on autogenous carrier flotation. The mechanism of autogenous carrier flotation is discussed using extended DLVO theory. The main conclusions are as follows: 1. the smaller the fine particles the more easily they adhere.to carriers; 2. the selectivity of autogenous carrier flotation depends on the selectivity of adsorption of collector. In the autogenous carrier flotation of ilmenite/plagioclase mixture assaying 15.35 per cent TiO2, a concentrate containing 47.17 per cent Ti02 can be obtained by primary separation with a recovery of 93.05 per cent. KEYWORDS: Autogenous carrier flotation, extended DLVO theory, ilmenite, styrylphosphonic acid.

Jan 1, 1993

By P. Wanjara, M. Xiao

During fusion welding of aluminium alloys, the avoidance of defects (such as porosity, oxides, hot cracking, undercutting) as well as the ability to optimize the microstructure-property characteristics in the assembly are critical for the stringent manufacturing specifications in the aerospace industry. In this work, aluminium alloy (AA) 2024 was electron beam welded autogenously as part of a study to determine the influence of parametric conditions on the characteristics of the heat affected and fusion zones to obtain optimal welding conditions. In particular the evolution in the weld geometry, microstructure and mechanical properties were examined as function of the processing conditions, including beam current, beam focus, beam oscillation, linear heat input and welding speed. For optimized parametric conditions, microstructural examination of the joints revealed narrow fusion and heat-affected zones comprising of dendritic structures without the occurrence of defects that enabled a maximized joint efficiency.

Jan 1, 2006

By Howard W. Adam

Mill length was the primary variable investigated in an autogenous pilot mill circuit. The 5-1/2' diameter mill had both pebble ports and 1/2" wide slotted grates. The plus 1/2" mill product was crushed in a cone crusher and returned to the mill feed along with the minus 1/2" plus 4 or 6 mesh fraction. Tests were run with a short mill, inside length of 26-3/8", or diameter-to-length ratio of 2.50 to 1. The same mill was then lengthened to 48-3/8", diameter-to-length ratio of 1.36 to 1. The effect of mill length on circuit product characteristics was studied. Results show that (1) circuit throughput or grinding rate is lower per foot of mill length in the longer mill, (2) the long mill product is finer than the short mill product, and (3) KWH per ton of circuit product is slightly higher with the longer mill; however, KWH per ton of minus 200 mesh material (finer fraction) produced is essentially the same in the long mill as the short mill, It is not known whether the relationships found for the pilot mill are valid for commercial size mills.

Jan 1, 1973

By A. R. MacPherson

"This paper considers four aspects of autogenous grinding. Part 1 discusses statements on power efficiency of autogenous grinding compared to conventional crushing and grinding systems. It also demonstrates how high-power efficiency can be obtained from autogenous grinding systems. Part 2 considers a simple method of testing ores to determine the type of autogenous plant which can treat these ores on a commercial basis. A comparison of testing for simple small plants vs large plants or complex ores is included. Part 3 considers important aspects which have to be considered in proper design of an autogenous grinding system. Part 4 discusses problem ores and how they can be treated in an autogenous system. INTRODUCTIONAfter about 35 years of using autogenous grinding plants in the mining industry, it is perhaps time to review where we are with this, by now, relatively old development. Autogenous grinding in this paper means grinding run-of-mine ore by fully autogenous means or by using a ball charge to assist the grinding (semi-autogenous). Also, autogenous grinding can be eitherby dry or wet.The use of autogenous grinding in the fifties was making its slow start, and it was not until the sixties that more of the mining industry would consider its use . By the seventies, most builders of new plants would have considered autogenous grinding, whether they used it or not, in the final design.In the eighties, most large plants use autogenous mills and to reduce over-all operating costs, many older conventional plants are now looking and actually retrofitting these old plants with autogenous grinding mills.It is evident that many misconceptions concerning autogenous grinding are still current. Some come from improperly designed plants which result from poor test work. There are many considerations in the proper design of autogenous plants. Some ores have been found to give problems even in a well designed plant. These ore types are beginning to be classified and recognition in the test stage allows steps to be taken in the design so that these ores can be efficiently handled in autogenous grinding plants.Therefore, this paper will address the following aspects of autogenous grinding:1. Misconceptions regarding autogenous grinding.2. Testing of ores to ensure a well designed commercial plant.3. Important considerations in mill design.4. Difficult ores, their recognition and types of design to handle such ores."

Jan 1, 1989

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977