Search Documents

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Hand arm vibration syndrome (HAVS) affects industrial workers exposed to long term hand-transmitted vibration from powered-tools. Peripheral neuropathy is a major component of the symptom complex of HAVS. Long term exposure to vibration causes myelin damage in peripheral nerves and reduces nerve conduction velocities in rats1. This study addresses the effects of acute vibration at constant acceleration of 49 m/s2 on myelinated fibers in peripheral nerves in Sprague-Dawley male rats using the ‘rat-tail vibration model,’ which simulates hand-transmitted vibration2. Methods Male Sprague-Dawley rats (~300 g) were assigned to vibration groups: 1 hr continuous vibration at 60 Hz; 4 hr continuous exposure at frequencies of 30, 60, 120 or 800 Hz; immediate and 24 hr following a 4-hr cumulative exposure of continuous and intermittent vibration at 60 Hz. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage accelerated by a B&K motor type 4809 and vibrated. Intermittent vibration was delivered in bouts of 10 min vibration alternating with 5 min rest periods repeated over 6 hr. Sham controls were restrained without vibration. After vibration exposure, the rats were anaesthetized, and the ventral nerve trunks from the proximal tail segment 7 were fixed in glutaraldehyde, embedded in epon-araldite and sectioned at 0.5 µm thickness and stained with toludine-blue for morphological quantitative analysis. The total number of myelinated axons in each cross-section of the nerve was counted using the Image J software. Myelin damage was identified by focal increase in area and intensity of toludine-blue staining and unraveling of the myelin sheath. Statistical analysis for comparing sham and the different vibration groups was done using Dunnett’s test. Animal treatment and all surgical procedures were approved by the institutional review board and compiled with the Laboratory Animal Welfare Act. Results The rats tolerated continuous vibration very well and exhibited no behavioral signs of stress. When exposed to intermittent vibration, there was increased vocalization, a startle reflex at the beginning of each bout of vibration, deposition of porphyrin around the eyes and transient hypersensitivity to touch.

Jan 6, 2006

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Acute vibration causes vasoconstriction in naïve human subjects1. Vibration-induced decrease in skin perfusion has also been reported in the rat-tail vibration model 2. After vibration exposure, rat-tail arteries demonstrate vacuoles in smooth muscle cells, similar to that caused by pharmacological vasoconstrictors3. This study addressed the effects of different frequencies, durations and patterns of vibration on lumen size and vacuole formation using the rat-tail vibration model in male Sprague-Dawley rats (~300 g). Methods The different groups were: 4-hr continuous vibration at 30, 60, 120 and 800 Hz; continuous exposure durations of 5 min, 1 hr and 4 hr at 60 Hz; and 4-hr cumulative exposure of 60 Hz delivered intermittently in cycles of 10 min on and 5 min off. Acceleration was set at 49 m/s2 r.m.s. for all frequencies. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage driven by a B&K motor (4809). The sham control animals were also placed in the vibration apparatus but not vibrated. Room temperature was controlled at 25 ± 1°C. Ventral arteries from proximal tail segments 7 were immersion fixed in aldehydes, embedded in epon-araldite and sectioned (0.5 µm) for morphological analysis. Vascular lumen sizes were measured as the percent ratio of the lumen perimeter to internal elastic membrane length using Image J software (NIH). The number of vacuoles in the smooth muscle layer of each artery section was counted. Results Fig 1: Semithin sections of arteries. A. Sham control. B. 4-hr vibration 60 Hz. In vibrated arteries, the lumen decreases in size, and smooth muscle cells (SMC) exhibit vacuoles (arrow). Bar equals 40 µm for each panel. [ ]

Jan 6, 2006

By G. B. Goodman, W. H. Pailes, P. D. Kaplan, I. Stachura, V. Castronova

"The risk of developing silicosis in underground coal miners, tunnel workers and some foundry workers is well-known. These persons generally develop the classic form of the disease over a prolonged period of time. Workers involved in abrasive blasting of bridges and those polishing tombstones have been reported to develop an acute form of silicosis within a few years of commencing exposure. Not well-appreciated is the potential for development of acute silicosis among drillers at surface coal mines. We report the case of a 33-year--old man who worked primarily at surf ace drilling, developed acute silicosis within three years of beginning exposure, and who initially responded dramatically to corticosteroid therapy. CASE REPORTThe patient is a 33-year-old white man who worked as a rock driller at a quarry and also at surface coal mines in western Pennsylvania since 1975. Prior to 1983, much of his work was done with a wet process in which water was applied to reduce dust generation. After 1983 he worked primarily as a driller at a surface coal mine using a dry process. He never wore a respirator. He described the dust as being so dense that he ""couldn't see anything.- In August 1986, he presented to his local physician with a complaint of pleuritic chest pain and shortness of breath. A chest x-ray film was obtained showing only a few p and q opacities. He continued working and these symptoms subsided, but the patient noted the onset of progressive weight loss. By May 1987, he had lost approximately 50 lb. In addition, he suffered profound malaise, dyspnea, migratory chest pain and arthralgia, fevers and drenching night sweats.A course of erythromycin therapy given in the hospital resulted in only fleeting improvement. Studies for Legionella and Mycoplasma infections were negative, as was a tuberculin skin test. The patient was transferred to Allegheny General Hospital in Pittsburgh on June 4, 1987.There was no history of serious medical illness, including tuber¬culosis. The patient admitted to smoking between I and 1 1/2 packages of cigarettes daily for 2 1/2 years prior to May 1987 when he stopped smoking. He denied intravenous drug abuse, homosexual activity or receiving transfusions of blood or blood products.On physical examination the patient was a thin, febrile white man who appeared chronically ill. Bilateral axillary and cervical lymphadenopathy was present. Chest examination showed restricted expansion and bilateral crackles. Examination of the heart and abdomen disclosed no abnormalities."

Mar 1, 1992

By Kristine M. Krajnak

Occupational exposure to hand-arm vibration through the use of powered hand tools can result in reductions in tactile sensitivity, grip strength and manual dexterity. In fact, even acute exposures to vibration cause shifts in vibrotactile thresholds in exposed fingers (2,4,5). Although reductions in tactile sensitivity after acute vibration exposures are transient, cellular changes associated with this shift in sensitivity could lead to the more permanent reductions in tactile sensitivity that are a common symptom of hand-arm vibration syndrome (HAVS). Methods Animals. Male Sprague Dawley rats (6 weeks of age) were used for all experiments. Animals were housed in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guideline for care and use of laboratory animals. Vibration exposures were performed by restraining rats in a Broome-style restrainer, and securing their tails to the vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control animals were treated in an identical manner except that the tail platform was set on isolation blocks instead of a shaker. Tail temperature and current perception thresholds (CPTs). Rats were exposed to 4 h of tail vibration (125 Hz, 49 m/s2), or restraint. Tail temperature was collected prior to and immediately following the exposure using an infra-red camera. Sensory neuron function was assessed by measuring CPTs with a Neurometer (Neurotron, Baltimore, MD). Transcutaneous nerve stimulation was applied to the C10 region of the tail. Three frequencies were used to test specific fiber types (5 Hz – C, 250 Hz - Ad, and 2000 Hz – Aß). The intensity of the stimulus was automatically increased in small increments until the rat flicked its tail. Tests at each frequency were repeated until the animals displayed 2 responses that were within 2 CPT (or 0.02 mA) of each other (2-4 tests/animal). CPT tests were performed prior to the exposure, immediately following the exposure, and 24 h after the exposure. Data Analyses. Temperatures were analyzed using a one-way ANOVA with animal as a random variable. ANCOVAS were used to analyze the CPTs at each frequency. Temperature at the time of the CPT test was used as a covariate, and animal was used as a random variable Results Tail temperatures declined between pre and post exposure (F(1,25) = 62.85, p < 0.001; mean ± sem pre 25.96°C ± 0.42, post 20.71°C ± 0.77), but were back to baseline levels by 24 h after the exposure in both groups of rats. The ANCOVAs demonstrated that exposure to a single bout of vibration did not alter sensitivity of C (5Hz) or Ad (250 Hz) fibers to stimulation.

Jan 6, 2006

By G. Roger Miller, Kristine M. Krajnak, Stephen S. Leonard, Stacey Waugh

Repeated exposure to hand-arm vibration through the use of vibrating hand tools can result in the development of the disorder known as hand-arm vibration syndrome (HAVS; (1,3)). One of the hallmark symptoms of HAVS is cold-induced peripheral vasospasms that result in finger blanching (4). Although the vascular and neural pathology associated with vasospasms has been described, little is known about cellular mechanisms leading to this damage (4). To understand how vibration may alter vascular and neural physiology and anatomy, rats were exposed to a single bout of tail vibration and the molecular responses of neural and vascular tissues were measured to determine if there are immediate or sustained affects of vibration that may underlie longer term changes in physiology. Methods Experiment 1. Male Sprague Dawley rats (n = 32, 6 weeks of age) were housed in AAALAC accredited facilities. All procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guidelines for care and use of laboratory animals. Vibration exposures were performed by restraining rats in Broome-style restrainers, and securing their tails to a vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control rats were treated in the same manner, except that the tail platform was mounted on isolation blocks and not on a shaker. The vibration exposure was 125 Hz, 49 m/s2, for 4 h. Rats were euthanized with an overdose of pentobarbital (100 mg/kg) 1 h or 24 hours after the exposure. RTqPCR was used to measure transcript levels for endothelin 1 (ET-1), the 3 forms of nitric oxide synthetase (NOS) NOS-1, NOS-2, NOS-3 and norepinephrine receptor subtypes 1D, 2A, 2C, in artery tissue, and to measure calcitonin gene-related peptide (CGRP) and nitric oxide synthase-1 (NOS-1) in ventral nerves. Data were analyzed using 2-way ANOVAs. Experiment 2. Male Sprague Dawley rats (n =24, 6 weeks of age) were maintained as described above. Animals were exposed to a single bout of restraint or vibration. Another group of animals served as cage controls. All animals were euthanized 24 h after the exposure, and tail arteries were isolated and frozen. Reactive oxygen species ROS) were measured using electron spin resonance spectroscopy (ESR). Arteries were homogenized over ice in 1 ml of PBS with protease inhibitor cocktail, using a tissue tearer (Biospecs Products Inc. Racine, WI USA). The sample was split into two 0.5 ml samples. One set had PBS and the spin label hydroxyl-TEMPO [0.1 mM] added while the other set had hydroxyl-TEMPO [1.0 mM] plus the specific hydroxyl radical scavenger, dimethylthiourea (DMTU), added to confirm the presence of the hydroxyl radical. Samples were vortexed and then placed in a flat cell for ESR analysis. The ESR spectrometer settings were: receiver gain, 6.32 x 102; time constant, 0.02 s; modulation amplitude, 1.0 G; scan time, 20 sec; magnetic field, 3490 ± 100 G (2). Data were analyzed using 1-way ANOVAs.

Jan 6, 2006

By P. Mundell, R. Torbin

"There are many physical and operational obstacles in pipelines that make the passage of inspection robots impossible including:•,Small radius bends•,Low operating pressure•,Plug valves•,Large changes in pipe size•,No permanent access to the pipeline.The inspection of unpiggable pipelines requires the marriage of a highly agile robotic platform with NDE sensor technology operating as an integrated system. Foster-Miller and GE/PII are developing a robot that is essentially a battery powered, train-like platform. Both front and rear tractors propel the train in either the downstream or upstream direction. Like a train, the platform includes additional ""cars"" to carry the required payloads. The cars are used for various purposes including the NDE sensor module(s), the power supply, and data acquisition/storage components. The robot is designed with a slender aspect ratio and the ability to change shape as required by the physical obstacle presenting itself. The MFL sensor module must also morph itself through the physical obstacles, and thus, will require some level of segmentation. The segmented MFL magnetizers and transformable sensor module represent a major advance in the science of sensor technology and pipeline inspection."

Jan 1, 2005

By Rosario Bernaola, Alejandra Díaz, Oscar Flores

Este trabajo tiene como objetivo evaluar el efecto del volumen de contenedor, la fertilización y riego en la fase de preacondicionamiento en vivero del Pinus douglasiana, así como su aplicación metodológica en Acacia Saligna, con el fin de incrementar el porcentaje de supervivencia a seis meses de su establecimiento en campo. El preacondicionamiento presentó efectos principales e interacciones entre el volumen de contenedor y la fertilización en las variables de crecimiento, con excepción de la altura y diámetro; mientras que el diámetro y peso radical presentaron una interacción entre el volumen de contenedor y el riego. La fertilización adicional no fue relevante para la absorción de minerales en contenedores de un litro y bajo condiciones de estrés hídrico. Como resultado, las plantas establecidas en contenedores de cinco litros sin fertilización adicional tuvieron mayores porcentajes de sobrevivencia en campo (>80%). Esta investigación está siendo utilizada para el diseño de estrategias de remediación de suelos degradados por la minería peruana, mediante la fitorremediación.

Sep 20, 2019

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By J. R. Pronovost, P. M. Tiley, D. W. Watts

"In 1980, J.S. Redpath Limited were retained by Dickenson Mines Limited to increase hoisting capacity from 700 to 1000 tons per day. The hoisting capacity of the present skip-over-cage system could not be increased significantly through design modifications. The other constraint was a minimum of disruption to the current production. The Dickenson shaft was a three-compartment shaft from surface to the 8th level and four compartments before the 8th to the 23rd level. The solution to the problem was to remove the services from the shaft man-way compartment from the 8th level to surf ace by drilling a borehole close to the shaft and rerouting those services through the borehole to the 8th level. A service compartment would then be available from surf ace to the 23rd level.By providing a service hoist in this compartment, the skip hoist would then be free to produce the 1000-tons/day required production. This paper will describe the search for the required hoist and the friction hoist selected for the project, and trace the design modifications required to modify the hoist to suit the Dickenson application and satisfy the Department of Labour safety requirements.The paper has been co-authored by J.S. Redpath Limited and C.L. Tiley Associates, who participated in the design changes and eventual commissioning of the hoist.IntroductionIn the earl y part of 1980, J.S. Redpath Limited conducted an engineering study on the Dickenson Mines Limited No. 1 Shaft materials handling system. The object of the engineering study was to investigate the possibility of increasing the tonnage hoisted from the No. 1 Shaft complex by adding a service cage compartment and service hoist. This would permit utilization of the existing hoisting plant solely for production hoi sting. A further consideration of the engineering study was that any alterations had to be accomplished with little, or no, interruption to production."

Jan 1, 1982

By M Bloss, B Roberts

BHP Billiton Olympic Dam required a well-tested software product suitable for strategic optimisation and scheduling of options for a potential underground mining project. The company has a standard software package called Blasor® that is used for open pit optimisation of complex deposits such as iron ore, copper-gold-uranium and silver-lead-zinc. It applies a mixed integer programming formulation (MIP) to produce conceptual pushback designs and an optimised pushback sequence. Schedules can then be run on the resulting mine designs. Existing pushback designs can also be imported into the model and an optimum schedule generated. One of the key advantages of Blasor is that multiple strategic mine schedules can be quickly generated according to the various scenarios, options and constraints that are being investigated.It was realised that Blasor, if carefully configured, could be adapted for use in underground planning. The concept of using Blasor as an optimiser for underground strategic scenarios is to represent the underground stope and development data in the form and structure of an open pit mine. In simple terms, underground stoping areas are modelled in the form of pushbacks (phases) with vertical walls. The phase dependency tools in Blasor are used to link mine blocks and their access development drives. These underground phases are imported into the optimiser. Artificial block models are constructed using stope design tonnage and grade data at various fixed cut-offs. A variable cut-off grade model has also been developed using a method of parcels to represent each cut-off grade increment.So far, this approach has been successfully used to investigate the optimum stope design cut-off for various strategic options, the economic potential of a series of mining and processing configurations and to provide guidance on the optimum sequence for developing and mining the various stoping blocks in the resource. Examination of the results has highlighted the most suitable development paths for more detailed study.CITATION:Roberts, B and Bloss, M, 2014. Adaptation of an open pit optimiser for underground strategic planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 249–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discontinuities in the earth&apos;s crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions below the earth&apos;s surface. As an outstanding example of the applications of this work, we have the so-called "seismograph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth&apos;s crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relatively abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 1, 1928

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

"The methods and technologies to be used for environmental monitoring of seabed mining activities are a key issue. Due to the large water depths, there are special challenges with respect to the monitoring equipment that is suitable. DNV GL has built up substantial experience of environmental monitoring from oil & gas projects in deep waters in the Norwegian Sea.Monitoring equipment and experiences from the oil & gas sector can to a large extent be applied to seabed mining.BackgroundThe International Seabed Authority is currently developing an environmental management strategy for the Area (ISA, 2017) as a part of the work on the regulations for exploitation for mineral resources in the Area.The draft environment strategy contains provisions related to monitoring and reporting of the activities. An Annex (Annex III) of the draft document describes the format and content of the environmental management and monitoring plan.The monitoring plan should contain, inter alia: ?Technology to be deployed.?Monitoring frequency of respective elements/components of the Marine Environment.?Monitoring procedures required to implement the Monitoring programme.?Details of the environmental monitoring stations across the Environmental Impact Area.?Monitoring specifics e.g. water quality; sedimentation rates; sound; plume extent; etc., as well as relevant Environmental Targets.?Monitoring of Mining Discharges.?Processes for Monitoring reviews and Environmental audits."

Jan 1, 2017

Hydraulic mining shovels can be successively used at open-pit mining operation in severe climatic zone with air temperature interval from -700C to +450C typical for some northern region of the world particularly of Russia, Canada and Sweden, if they would be equipped by special preheating facilities for their diesel engine, water, hydraulic oil and lubrication systems. All shovels manufactured by the Komatsu Mining Germany GmbH for operation at ambient air temperatures down to -50¦C have cast and forged structural design elements, bolted connections made of special steel grades, electric cables with special insulation, flexible high-pressure hoses manufactured by ICE-Champion with connectors made of special steel grades.Generally at the temperatures below -25¦C the ordinary machine has to be stopped, the attachment should be placed in the parking position, the generator should be switched on, or the external electrical power supply connected, for the preheating equipment. For rapid start-up in winter after a long shutdown of a hydraulic shovel, there is a procedure for preheating of the main systems. It is applied for the following systems: engine cooling system, engine oil, hydraulic oil, pumps and drive motors of the propel gears, electric cabinets, machinery house, especially near the ventilation inlets and outlets.Start-up of the main drive engine is permitted at a hydraulic oil temperature of -20¦C, when it has a viscosity of 1000 cSt. In this case the rotation speed of the diesel engine crankshaft is lower by two times than the nominal value and this is the most favourable condition of start-up of the engine and hydraulic pumps and motors, which work with half of their rated rotation speed until the hydraulic oil reaches a viscosity from 100 to 10 cSt. After that the hydraulic system and the entire shovel begin to operate under normal conditions.

Dec 6, 2010

By Leslie Gertsch

Outline First progress report ? ?Introduction ?Non-terrestrial mining ?Near-term targets ?Stages of mining ?Study procedure Capabilities needed for non-terrestrial mining ?Mining methods ?Mining unit operations ?Typical surface mine operations sequence ?Results to date General effects of gravity ?On fragmentation ?On excavation ?On transport ?Conclusions / Recommendations

May 1, 2013

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012

By Hilden. M.

"As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill’s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design. INTRODUCTIONSince the Cadia mill was the first 40ft diameter SAG mill, its performance, liner and discharge design has attracted considerable international attention, as reported in previous SAG conferences. The mill experienced particular challenges with regard to pebble and slurry discharge, which necessitated a discharge redesign, incorporating a considerably greater pebble port open area and curved pulp lifters (Hart, Valery, Clements, Reed, Song & Dunne, 2001). Packing between lifter bars on the shell liner was found to dramatically reduce mill throughput over the first half of the liner life. In response, the liners were redesigned to a 2/3 spacing so as to open up the space between lifters. Due to ongoing high liner wear issues, the liner was redesigned based on the discrete element modelling (DEM) of Conveyor Dynamics conducted by Nordell and Potapov (2001). This aimed to maintain mill throughput with new liners and provide an extended liner life. This design was kept proprietary for many years, so has not been open to review."

Jan 1, 2012

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By Brian Gar Wingfield

"The introduction of the QuarryMan laser profile system in 1987, along with the development of the corresponding 3-D software, gave a qualified operator pertinent information about dimensions of quarry highwalls, pattern and hole loading design, stockpile profiles, etc . . . Attributes helpful for this endeavor included surveying, computer, and blasting knowledge. Since not all operators had theseskills, a simpler model, the QuarryAce, was designed to look a t highwall dimensions in 2-D view . Al though less sophisticated than the QuarryMan instrument and its software, it is simpler to instruct in its use and has the ability to determine burdens at different depth levels . An in-house user f r i e n d l y computer program was designed to utilize QuarryAce depth vs. burden data . This program was created to enable laser and computer novices to generate information useful to the everyday blaster."

Jan 1, 1992