Search Documents

By Ian Martin

A precious metals refinery’s switch to personal computer-based, three-dimensional piping design saved many hours in the design of a South African precious metals refinery. Bateman Minerals and Industrial provided engineering, procurement and construction management services for Impala Platinum Limited-Refineries’ new $60 million refinery in Springs, South Africa. This project is one of the largest platinum refineries in the world. Bateman evaluated a new design method during this project that involved developing a three-dimensional model for the project. The new method saved time by reducing the man-hours required to generate complete project documentation, including plans, sections, isometrics and material takeoffs. The new method also saved design and construction time by allowing designers to detect clashes before construction began.

Jan 1, 2000

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

There are many inherent risks in creating a mine plan for a new ore zone in an underground mine; one of such risks is the redistribution of stresses that could be a cause of instability. Using numerical modelling tools, it is possible to model the planned stope extraction sequence and evaluate the influence of mining induced stresses on the stability of remnant pillars, and use this information to remedy potential setbacks. This paper demonstrates this approach through a case study of the short-term mine plan of the Lapa mine of Agnico Eagle Mines Ltd., an underground gold mining operation near Val d?Or. Three-dimensional boundary element modelling is used to compute the stresses induced by the stope extraction sequence as planned with a longitudinal retreat mining method. The proposed methodology can be generalized to other mines that require an understanding of the stress concentrations at the pre-feasibility stage of mine design.

May 1, 2009

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

By Victor F. Hollister

Skam deposits considered as porphyry copper deposits have been classified into three basic prospecting models: (I) the skam deposit associated with a mineralized intrusive (Pima-Mission), (2) the deposit associated with a barren igneous stock (Ertsberg), and (3) mineralized rock that seems to have no clear association with apluton (Phoenix). Pima-Mission, Christmas, and many other copper-bearing skarns developed in carbonate sequences near mineralized intrusives form an important part of the deposit. Historically, copper derived from the mineralized intrusion accounts for less than half of the metal produced by most porphyry mines, as most mineralization occurs in the intruded rocks. Skam mineralization is an important part of wall-rock metal deposition, because carbonate sequences are preferentially replaced by sulfide and skarn minerals. Exploration for skam mineralization is an important phase of porphyry copper exploration. Impure carbonate beds can become better host rocks for skam deposits than pure carbonates, and these in particular should be included in porphyry-exploration programs if the impure strata are cut by the stock. Skam deposits can also form near stocks that are barren of sulfide. In this model, the two best ore guides are strata favorable for mineralization (usually impure carbonate beds) and the intrusive contact. Faults can also act as important ore controls. Some skarn deposits form that have no clear genetic connection with a stock, although intrusive rocks are known in the district. In such cases, the best ore guides are strata and district-wide faulting. Dikes and sills are also common and mineralization can locally prefer their contacts even though the igneous rocks are barren. Skam minerals are influenced by the chemical composition of the carbonate. Forsterite, brucite, tremolite, and talc are common in skams developed in dolomitic beds. Skams derived from calcic beds often contain wollastonite, calcite, stilbite, or idocrase. Diopside, however, is a common accompaniment of copper sulfide in skam regardless of the original composition of the carbonates. Tremolite and possibly other amphiboles and chlorite can occur significantly in the zinc-lead portion of skams. Gamets occur in magnetite, copper, and zinc-lead zones of skams, but are not as diagnostic as diopside for the copper zone or tremolite for the zinc-lead zone. A general desciption of skam-deposit mineralogy can be used to construct prospecting models of porphyry copper skams. An abstract of such a description follows.

Jan 1, 1991

By David E. Sims

Asarco has been using computer-aided open-pit mine design since 1966. The in-house developed program package includes drill-hole analysis programs, interpolation routines, and three-dimensional open-pit design programs. The financial analysis step after pit design required that a reasonably accurate schedule be produced so that a good cash flow model could assess the feasibility of a project. The manual method of scheduling was too time-consuming for feasibility work, so a computerized scheduler was required. Since no computerized mine scheduling programs existed, we requested proposals from consulting firms to develop such a program. The selection of a consulting firm, the formulation of the contract and design specifications required about three years to accomplish. The consulting firm, Systems Control Inc. (SCI), of Palo Alto, spent over one year doing the programming and testing alone. The details of the program development were reported in "Computerized Year-by-Year Open-Pit Mine Scheduling," SME-AIME Transactions, December 1974. In June of 1973 the program, which SCI dubbed Optimum Resource Extraction or ORE, was installed. Version 1 of ORE was utilized successfully on three separate properties over a period of two years. During this time it became obvious that some of the original design specifications were restrictive, and certain modifications were required. The ORE program was submitted for modification, and after one year version 2 was operational in May of 1976. The program now consists of approximately 20,000 lines of FORTRAN source statements grouped into 190 subprograms, and runs in a 450K region of Asarco's 370/148 in Cranford, NJ. The Tucson com¬puter (370/115) is tied to the Cranford computer via a 9600 baud leased T.P. line, for running mine scheduling and other large mine planning programs.

Jan 1, 1979

By K. V. S. Sastry

Pelletization, sintering, and pressure compaction are the most common methods used to agglomerate ore concentrates. Over the last 20 years agglomeration has grown enormously in popularity and has become a standard unit operation in the nonferrous, cement, fertilizer, and ceramic industries. However, it is in the processing of iron ores and the preparation of blast furnace feed that agglomeration is used most and its application has grown fastest (Ball, et al., 1973; and Sastry, 1977). This chapter deals with an account of the current practices and future trends in the application of computers relative to an overview of the process design and engineering considerations of the unit operation of agglomeration.

Jan 1, 1979

By L. H. E. Weyher

A mine is essentially a vast materials-handling system. All other systems found in the mine exist to one degree or another to support the materials-handling functions, from the cutting at the face to the hoisting in the shaft. In this chapter computerized planning of underground materials-handling systems will be examined by dividing this function into: (1) the planning of the production section, and (2) the planning of underground rail or belt haulage from the production section to the shaft, slope, or surface. While alternative divisions might focus on the different materials- handling functions, i.e., production, supply, and manpower transportation, historical computer analysis has focused on the various systems rather than functions. The emphasis in this chapter is directed toward coal mine applications; however, most of the programs and methods are equally applicable to other underground mines. Markedly different methods are encountered in each system, and moreover, marked differences exist in the nature and the degree to which the materials-handling subsystems in each interact with the environmental or support systems. The most intimate interaction exists at the faces where geologic, human, and machine performance factors are closely related and constantly varying. In view of this, the planning of the materials-handling systems for the face will usually stress flexibility, while the outby materials-handling systems will generally place decreasing emphasis on flexibility and more on system reliability, capacity, and cost effectiveness. Thus, hoisting and main haulage systems are generally designed and constructed as permanent installations and cannot be readily changed, whereas secondary haulage systems and face operations are relatively mobile. These differences may have considerable significance for the mine planner in making technical and financial comparisons of alternatives to provide the scheduled mine production.

Jan 1, 1979

By R. C. Fox

The geophysical aspect of reconnaissance marks the beginning of extensive computer applications supporting development of a mine. Although there are some storage and retrieval applications in geology, and some statistical analysis in geochemistry, large-scale compilation, reduction, and interpretation of mineral resource data are initiated in reconnaissance geophysics. The reasons for this fact are quite simple. Geophysics is oriented toward quantitative evaluation of areas of interest, and methods of data collection are automated to the extent that large amounts of analog and digital information are recorded. The large volume of data must be interpreted in a reasonable time. Furthermore, some modeling problems involving complex numerical solutions could not be attempted without the computer. Therefore, the computer is essential to the success of an exploration project using geophysics. For example, aeromagnetics is a common technique for reconnaissance examination of areas associated with sulfide systems and porphyry deposits. An area covering 161 X 161 km (100 X 100 miles) may be flown with a 1.6-km (1-mile) line spacing yielding 10,000 line miles (16,093 km) of data. If only 10 measurements are recorded per mile, 100,000 data points, including location and magnetic field intensity, must be reduced and stored for quantitative interpretation. Computer applications often represent a significant investment in manpower and hardware. It is desirable, therefore, to initiate an engineering approach to the application of computers to geophysics. By this it is meant that computer programs and systems should be formulated, developed, and implemented in a disciplined manner such that their usage is dependent only on the application and not on the individual doing the programming. In other words, computer application, development, and usage should evolve beyond the personal gadget phase to an important applied technology. Geophysics has evolved over the past two decades in a course parallel to computer hardware development. During the sixties, the computer became large enough and fast enough that complex models required by geophysics could be solved. Automation also relieved the geophysicist from routine manual calculations. During the seventies, computing power in¬creased and applications expanded from two-dimensional problems to three-dimensional modeling. Moving into the eighties, as computer hardware costs will significantly decrease, the major expense of computing will be the manpower required to develop, implement, and use an application; therefore, improved programming techniques and applications software engineering methods will be used to optimize and preserve this investment. This chapter presents a general overview of computer methods in geophysical reconnaissance; it is divided into two parts: geophysical methodology and software engineering.

Jan 1, 1979

By Edward L. Beutner, Robert M. Crump

Benson Mines low-grade iron ore reserve is a replacement deposit within the Grenville gneisses of the Adirondacks. The average grade of the crude ore is about 23 per cent iron. The iron minerals are principally magnetite and hematite disseminated throughout the gneisses as discrete grains about 1 mm in size. Both the ores that are beneficiated by magnetic means and the non-magnetic ores that are treated by a gravity method of concentration are found in stratigraphically different positions but are mined from one open pit, which is about 2.5 miles long and 800 feet wide and are treated separately. The gneisses are described and named according to the distinctive mineralogy of each. Recognition of the gneissic types permits the interpretation of the structure as a northward-plunging syncline overturned to the west. A large subsidiary anticline-syncline complex occurs on the east limb of the major syncline. Iron minerals in sufficient quantity to be considered ore are confined to areas where the footwall rock has been overturned to become the hanging wall.

Jan 1, 1968

By Robert M. Dreyer

AGGREGATE With an annual domestic production of over 1.6 billion tons at a value of over $2 billion (see Table 15.1.1), the production of aggregate (crushed rock, sand, and gravel) is a basic industry of utmost economic importance. Because of the role of aggregate materials as essential ingredients of concrete, asphalt surfacing, and plaster, their delivered prices are major factors in determining the cost of construction. The annual domestic production comes from nearly 10,000 plants. About 15% of these plants account for over one-half the production. In a rapidly inflating economy, the average mine sales price of aggregate has remained relatively stable. The actual mine sales prices, however, vary greatly depending on quarrying costs in various parts of the country. Of much more importance in construction costs, however, is the delivered price of aggregate. This varies for each job, depending on the distance from the quarry and resulting transportation costs, as well as the initial cost at the mine. Because of a proliferation of regulations limiting new quarries in the vicinity of the encroaching urban sprawl, the average distance which aggregate must be transported has been increasing rapidly. Although it is impossible to derive an average delivered cost for aggregate, it should be noted that even an increase of only $1 per ton in average delivered cost over the last decade (probably a minimal assumption) would mean an annual cost $1.5 billion higher than ten years ago. In recent years, structural engineering considerations, as well as an increasing use of lightweight concrete blocks, have resulted in a rapidly increasing demand for lightweight concrete and plaster, the essential ingredient of which is lightweight aggregate. Principal lightweight aggregates are: pumice, slag, perlite (thermally expanded hydrous volcanic glass), vermiculite, and expanded shale, formed by the thermal expansion of shale and slate. The United States now has the capacity to expand, annually, over 13 million tons of shale and slate and to expand over 600,000 tons of perlite. In locating a site for aggregate production. the following factors must be considered: (1) tonnage available; (2) quality of aggregate (including local variations); (3) distance from major use areas; (4) transportation costs, including those resulting from present and possible future haulage restrictions; (5) zoning regulations; (6) operating costs, including the cost effects of compliance with local regulations governing blasting, air pollution, water pollution and drainage, noise levels, and operating periods. At one time, locating a suitable site for the production of crushed rock, sand, or gravel, in most areas, was regarded as an extremely simple task. In the past few years, however, finding a site for profitable production of aggregate has assumed ever-increasing com-

Jan 1, 1976

By Peter W. Lotz

Contents of: ?Sampling for Cyanide in Metallurgical Processes? ?Sampling at process level of operation ?Sampling at environmental level ?Sample stability and integrity issues ?each citing possible objectives, practical example and reasons for surprises Overall recommendations on sampling plans and procedures to maintain sample integrity

Jan 1, 2005

By R Kerrich

Early-Archaean (3.26 Ga) volcanogenic massive sulphide (VMS) deposits located within the low strain and sub-prehnite-pumpellyite metamorphic-grade Strelley greenstone belt, East Pilbara, Western Australia, contain exceptionally well preserved sulphide textures which are directly analogous to those of sulphide chimneys formed by black smokers at present day submarine hydrothermal vents. The VMS deposits are associated with seafloor alteration zones in and below silica-carbonate laminites, at the top of tholeiitic to calc-alkaline intermediate and felsic rocks. VMS mineralisation comprises stratabound Zn-rich sulphide lenses with significant Cu and barite, and variable Pb and Ag, above Cu-rich stringer zones, all of which are similar to Phanerozoic polymetallic or Kuroko VMS deposits. Sulphide-sulphate mineralisation implicates hydrothermal discharge into sulphate-bearing ocean waters, ruling out a globally anoxic Archaean hydrosphere. The volcanic rocks and co-magmatic sub-volcanic intrusion hosting the VMS deposits are characterised by the conjunction of LILE>LREE>HREE, and Phanerozoic La/Yb with negative normalised anomalies of Nb, P and Ti, consistent with derivation via subduction zone hydrous metasomatism fusing the mantle lithosphere.

Jan 1, 1995

By Mark Dangerfield

[Power-Point Presentation]

Jan 1, 2005

By Donald W. Gentry

Mine valuation is a multifaceted, interdisciplinary process by which the economic viability of an old, existing, or new mining property or venture is determined. The problems associated with arriving at a representative and accurate value for a mining property are complex and numerous, and the procedures utilized in determining these values vary from simple, back-of-envelope calculations to sophisticated mathematical manipulations requiring computer modeling and analysis. Regardless of the complexity or the degree of sophistication associated with any particular project, the evaluation process must ultimately provide management with two basic types of information. First, the evaluation process should indicate whether or not the mining project is economically viable after careful consideration of all engineering, environmental, geologic, and other variables pertaining to the project. Second, the evaluation process should provide management in- formation on the relative attractiveness of the project when compared to other alternatives. In some cases, it may be extremely difficult to supply this information for a project directly. Nonetheless, the evaluation process should and must present all information necessary in a format which can be incorporated into the decision-making process as expeditiously as possible.

Jan 1, 1979

By Joel Moskowitz, George J. Tamaro

"A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140m by 100m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations, the seam dipped below rock that is more competent. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half. The tower covering the south half of the site was topped out in 2002 and the garage levels in the north half of the site were completed in 2003.PROJECT DESCRIPTIONIn September 1999, a major investment company began the due diligence process to evaluate a property on the shore of the Hudson River in Jersey City, New Jersey for a new multi-use complex. The site offers a spectacular view of lower Manhattan directly across the river from the site of the former World Trade Center. The site, covering two city blocks, was previously occupied by manufacturing and office facilities of Colgate-Palmolive.The building footprint is approximately 140m by 100m, the southern half of which is occupied by a 260m tall office tower, shown in Fig. 1. As of this writing, design of the structure for the northern half of the site has not been finalized, but it is expected to comprise an 11-story office building. A glass-covered atrium will occupy the street that formerly separated the two blocks. As part of the due diligence process and preliminary design evaluation, alternatives were considered to accommodate various numbers of parking places, both above and below existing grade. A major consideration for below grade parking is the proximity of the Hudson River some 25m east of the east building line."

Jan 1, 2004

By Kevin Lundberg, Philip Sander, Daniel Weinberger, John Reilly

Since the early days of risk management, developments in technology and guidelines (ITA, ITIG, OGG, UCA) have advanced risk management and probable cost estimating, which are now widely recognized. WSDOT’s CEVP risk-based cost validation process is now established after 20 years. This paper traces these developments, summarizes advanced techniques, and presents examples of US and international projects with results. A particular case of using advanced risk evaluation to allow enhanced-capability TBMs to be considered in a competitive bid process is presented. Further advances, including the use of digital twin risk-based representation of complex projects, are described.

Jun 13, 2023

By S. Uihteenmaki

Pyhasalmi is a massive sulfide orebody located in central Finland. The mine has been in operation since 1962. The flotation concentrator produces Cu, Zn, Pb and pyrite concentrates. The plant has used an on-stream analyzer for process control since 1968. The original analyzer has overlived a few generations of minicomputers, but the analytical parts are essentially unchanged. The on-stream analyzer is a critical component in plant process control system, which has made Pyhasaltni one of the pioneers in the art of computer control and optimization of flotation plants. The paper summarizes the experiences gained from the use of the high performance elemental analyzer system and the proven benefits from the use of on-stream analyzers at a complex sulfide flotation. The aging analyzer is approaching the end of its useful life. A new state of the art analyzer system is undergoing testing at Pyhasalmi.

Jan 1, 1999

By J Player, G Sweby, S Webber, E Jones

Seismic systems are a tool for the monitoring and forecasting the rock mass response to excavation. Common issues encountered at mine site audits and reviews are: how to design an effective seismic system, implementation of the design, interpretation of seismic source results and understanding the reliability of the seismic source. These issues are often a function of several items including: • Experience of site personnel in undertaking seismic system design. • Personnel not envisioning multiple phases of system expansion to understand system robustness issues. • System design/expansion occurring in response to damaging seismic activity rather than planned expansion of a system • The mine access development is often localised in comparison to the total orebody being mined hence, planning sensors in longholes in advance of development rather than in short holes close to development will improve the three-dimensional aspect of the network. • Limited site processing of the seismic event data, hence engineers do not see the uncertainty associated with event location, size, source and system layout. Mine site users require a framework to appreciate the challenges and limitations in locating large events. For example, event locations are given as precise measurements (to the nearest centimetre) whereas the volume of deformation resulting in the event often has dimensions of tens of metres or more (as defined by the source radius). A stronger awareness of the uncertainty of rock mass yield within large seismic sources will assist site users in the interpretation of rock mass damage. The encountered design and implementation errors are reviewed and discussed with a practical set of rules presented to provide a robust seismic system that provides consistent results and increases the user’s understanding of uncertainty in source location and size. The authors’ experience across multiple mine sites, seismic systems and damaging seismic events over a 30 year period has been summarised into practical rules for site personnel of all experience levels.

Nov 29, 2022

By R. E. Radabaugh, J. M. Brown, J. S. Merchant

The Gilman district is on the northeast flank of the Sawatch Range in central Colorado. It has yielded a total of 10,000,000 tons of ore having a value of over $250,000,000. Paleozoic sediments intruded by a Tertiary quartz latite sill and unconformably overlying Precambrian intrusives and metasediments comprise the country rock of the area. The sediments strike northwesterly and dip 8° to 12° northeasterly. Structures in the Precambrian are related to the Homestake shear zone of the Colorado mineral belt. Only minor folding and faulting occur in the sediments. The principal ore bodies are massive sulfide replacement deposits in carbonate rocks. They consist of long, pipe-like mantos in the completely dolomitized Mississippian Leadville Limestone and funnel-shaped chimneys of copper- silver ore cutting across the Mississippian and Devonian strata. Mineralization is continuous from the chimneys into the mantos. The principal ore bodies are roughly in the shape of a four-tined fork which points up dip. Smaller manto deposits occur in the Cambrian Sawatch Quartzite, and fissure veins are present in the Precambrian rocks. The principal minerals in the mantos are marmatite and galena in a gangue of pyrite and manganosiderite. The chimneys consist of a central core of pyrite with erratically distributed chalcopyrite, tetrahedrite, freibergite, and occasional galena with a shell of zinc ore on the outer margin. Both the chimneys and the mantos are surrounded by imperfect shells of manganosiderite and sanded dolomite. The mineralization is of Laramide age. Hydrothermal alteration affects all rock units to varying degrees. Clay mineral alteration halos occur around the ore bodies. Hydrothermal solutions have developed sanded rock, rubble filled channels, and banded zebra textures, principally in the Leadville Limestone. Structural control of the ore bodies is not well defined. Both the location of the district and the chimneys are probably related to basement structures. The mantos are largely controlled by stratigraphic factors and a pre-Pennsylvanian karst topography in the Leadville Limestone, which were modified by hydrothermal activity, and by weak zones of northeasterly trending faults.

Jan 1, 1968