Search Documents

By C. F. Gleeson, D. G. Sheehan

"The results of humus and overburden geochemical surveys over the Doyon, Bousquet and Page-Williams gold ore deposits are presented.These studies show that humus sampling for gold gives negative results over the Doyon deposit. The lack of response is probably caused by the presence of 1 m of relatively impermeable glaciolacustrine clay and silt that overlies 1 m to 2 m of till over the surface expression of the ore zone. By contrast, positive responses for gold occur in humus samples over the Page Williams A and C gold deposits. The ""A"" ore zone is covered by several metres of exotic calcareous till over 0.5 m to 1 m of older, locally derived till. Anomalous values for gold in humus range from 10 to 35 ppb over the orebody. Overburden over the ""C"" ore zones is much thinner, generally it consists of less than 2 m of sandy till. Trenching humus anomalies that range from 10 to 1360ppb Au uncovered the gold mineralization. The geochemical dispersal trains in till from the Doyon orebody and the Page-Williams ""A"" zone are relatively short (i.e. less than 200 m) because both deposits occur in the lee of bedrock highs that shielded them from extensive glacial quarrying. Dispersal trains from all three pyritic gold deposits can be defined using either the fine fraction or heavy mineral fraction of the till.The intensity of the gold in till anomalies over the ore zones is variable. Therefore, it would be misleading to attach rigid significant threshold gold values to overburden drilling results. Each case must be evaluated based on bedrock topography, sample density, overburden type, thickness of till, as well as size, type and orientation of the target exposed to glacial erosion."

Jan 1, 1987

"Australia’s largest rail freight network operator, the Australian Rail Track Corporation (ARTC), has selected GE Transportation’s Movement Planner solution as the key technology enabler for its Hunter Valley-focused network control optimization program.ARTC’s Newcastle-based network control, is the nerve center of Hunter Valley rail operations, where locally based train control professionals make thousands of decisions every day to safely support the annual movement of more than 24 kt/h (26,400 stph) of freight, and tens of thousands of coal, freight, grain and passenger trains each year.ARTC plans to transform its train control function by integrating and then building on Movement Planner, an advanced software solution by GE Transportation that provides real-time rail traffic planning and optimization to enable freight to move more efficiently. “The Hunter Valley rail network is one of the busiest and most complex in the country, supporting the largest coal export port in the world,” ARTC managing director and chief executive officer John Fullerton said.“As bulk freight demands grow, rail operators like ARTC and supply chains like the Hunter Valley coal network need to be creative in the way they respond so the Australian economy doesn’t miss out. That’s why we have conducted a worldwide search to find globally proven solutions that will improve our network productivity and efficiency,” Fullerton said.The Movement Planner solution considers multiple factors including train schedules, trafficcontrol systems and train movements relative to each other and then develops an optimized traffic plan for the trains throughout the network. Existing GE customers have benefited from increased visibility of network operations, higher velocity, less dwell times, and improved on-time performance across their networks."

Jan 1, 2018

By James A. Robertson

"In the Blind River area Proterozoic clastic and sedimentary rocks and minor volcanic rocks (The Huronian Supergroup) uncomformably overlie and trangress northwards over dominantly granitic Archean terrane (2500 + Ma) and are intruded by Nipissing Diabase (2ll5 Ma). Later deformation and metamorphic events are recognized. The developing depositional basin was controlled by the incipient Great Lakes Tectonic Zone marginal to the Algoman Craton.The Matinenda Formation (basal Huronian) comprises northwards-derived fluvial arkose, quartzite, and pyritic, uraniferous oligomictic conglomerate which contained in 1981 some two-thirds of Canada's uranium resources. Production to December 1981 from Elliot Lake totalled 98.3 thousand tonnes U for an average recovered grade of 0.1% U with an additional 671 tonnes U recovered by leaching at Agnew Lake. The remaining resources are at lower grades. Some thorium and yttrium have been produced. Minor amounts of gold reflect the paucity in the source area. Gold is better-developed in the Huronian north of Sudbury reflecting the local source area.The conglomerate beds lie in southeasterly-striking zones controlled by basement topography down sedimentation from uraniferous Archean granite. Uraninite textures, the distribution of monazite, and local enrichment by reworking indicate a syngenetic, probably placer, origin of the mineralization. ""Brannerite"" has formed by solution of uranium from the margins of the uraninite grains and redeposition on the original titaniferous minerals. Penecontemporaneous volcanics may have been a source for sulphur in some of the pyrite and of trace amounts of Co, Ni and Au. Some pyrite may be detrital, some may be authigenic and some introduced.Drab coloured rocks, uranium and sulphide mineralization, the presence of hydrocarbon (thucholite) and a post-Archean regolith formed under reducing conditions have been cited as evidence of an early Precambrian reducing environment extended to the atmosphere. Sedimentary features indicating fast-flowing water and possibly a cold climate imply that the uraninite would be exposed to whatever oxygen was present in the atmosphere under conditions which would inhibit complete solution. In the upper Huronian, red beds and in the Lorrain Formation a monazite - iron oxide assemblage and copper mineralization indicate more oxidizing conditions. . Similar uranium deposits occur at Agnew Lake and in the basal Huronian north of Sudbury there are minor uranium and gold values.Provenance, lack of complete oxidation, transportation and depositional processes, redistribution during diagenesis and possibly low grade metamorphism, and the lack of post-depositional destructive processes are the dominant factors in the formation and preservation of the ores. The modified placer theory of genesis is well entrenched and an exploration model for such deposits throughout the world is well-documented.Research continues on mineralogy and textures of the ores, detailed sedimentology of the ores and their host rocks, with particular emphasis on: provenance area, the influence of early Precambrian mineralization patterns on the mineralization present in the Huronian both in space and in time, fluvial sedimentation and diagenesis. Expansion and reopening of the mines of the Elliot Lake camp should facilitate further studies."

Jan 1, 1986

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By Jorge Olivari Ortega

El presente texto señala la función del último gobernante del Imperio Inca, Túpac Cusi Huallpa y su relación con los tesoros escondidos de este, producto de la explotación de yacimientos auríferos

Jul 1, 2015

HW Process Technologies, Inc. (HWPT) has developed a patented membrane-based ion fractionation system, which specifically separates copper from gold and silver species in a cyanide matrix. This Engineered Membrane Separation (EMS?) system was pilot demonstrated on the 82,000 liters of pregnant leach solution' (PLS) generated from tailings, via thin layer leaching, at a mine site in Durango State, Mexico. The EMS? recovered ~90% of the gold-silver cyano-complex to a 90% volume permeate (based upon an EMS? feed stream of 100% volume) while rejecting -90% of the copper cyano-complex to a \0% (by volume) concentrate. The EMS? technology combines pore-size specific electro-statically charged membranes with engineered materials of construction and application-specific operational design that reject multi-valent, ionically charged species to the concentrate and transmit mono-valent species through the membrane to the permeate. The 850 ppm Cu PLS contained approximately 0.8 gil free NaCN with, the copper cyano-omplex principally in the CU(CN)3 and CU(CN)4 forms. The gold grade of the PLS was -2 ppm Au. The ~LS calcium concentration at -700 ppm Ca was reduced to ISO ppm.Ca (± 50 ppm) by sodium cycle ion exchange pre-treatrnent prior to EMS? processing.

Jan 1, 1998

Membrane technology has been available for over 36 years, but has been used sparingly in the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and techniques and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane based systems in the mining industry. Harrison Western has expanded the use of this “new” technology to enhance the use of membrane technologies to separate metals from large volume heap leach mining solutions containing copper, zinc, and iron, gold or silver. Moreover, membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries like separating metals from acids or concentrating acids and producing high quality process fluids. Finally, wastewater from Acid Mine Drainage (AMD) or, as in the case of the Newmont Yanacocha Mine in Peru, the treatment of excess barren leach solution created during the rainy season, can be cost effectively processed to meet World Bank Standards for surface discharge. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold, silver, copper, zinc or nickel. Recent applications have been developed for spiral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operate on feed streams from 140° C to 300 centipoise. Opportunities exist to apply membrane technology to concentrate gold, silver, copper, zinc or nickel using thin film composite membranes. Engineered membrane types can operate across the spectrum from low pH (<2) acid applications to high pH > 10 cyanide applications. Incorporating HW EMS™ membrane technologies into current mining operations could allow one to increase production because the membrane technology would be used to pre-concentrate heap leach solutions, and therefore, increase utilization of existing extraction and refinery capabilities.

Jan 1, 2007

By H Kim, M J. Sun

In order to reduce carbon emissions from the steelmaking process and achieve carbon neutrality, global steel companies are establishing their own medium to long-term strategies and implementation plans using competitive technological advantages held by each steel company. At this point, Hyundai Steel has formulated a product-oriented carbon-neutral strategy based on innovative processing that makes use of Hyundai Steel’s own strength. Based on our experience in electric arc furnace product manufacturing and blast furnace operation in an integrated steel mill, Hyundai Steel is driving the Hy3 (Hy-cube) project, which involves a unique hybrid production system utilising hydrogen and hydrogen-based renewable energy sources. This initiative aims to achieve carbon-neutral production and eventually specialise in producing premium carbon-neutral automotive parts. The project has originality in that it involves not only designing processes using electric furnaces to produce premium steel products such as car body panels and electrical steel sheets, but also aims to reduce carbon emissions from the process, developing carbon-neutral products based on market demand. To assess the feasibility of the Hy3 project, Hyundai Steel conducted two pilot productions. The first pilot was producing a prototype of lower-arm part using electric arc furnace with three different kinds of raw materials: molten iron, HBI (hot briquetted iron), and scrap. Successful performance evaluation of auto parts with 1 GPa strength was achieved. The second pilot has been focused on tire cord steel, with the first-phase tests yielding a 33 per cent reduction in carbon footprint (CFP). Using the advantages of operating experience in electric arc furnace, Hyundai Steel is preparing for test operations producing various automotive parts using an electric arc furnace (EAF) to advance the Hy3 concept. From a medium to long-term technological development perspective, Hyundai Steel’s blueprint includes producing high-end carbon-neutral steel products using hydrogen-reduced iron as raw material.

Jun 19, 2024

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Nick Vayenas, Ming Cai, Hongbin Zhang Lorrie Fava, Enrique Acuña

"A hybrid methodology is proposed to improve the accuracy of Diesel Particulate Matter (DPM) concentrations simulated in a ventilation network model by using Computational Fluid Dynamics (CFD). DPM, as a primary concern for underground hard-rock mines, has been studied in two dominant numerical models, ventilation network solvers and computational fluid dynamics. Ventilation network solvers are efficient, but they are not able to provide three-dimensional DPM concentration contours and only accept area-average DPM data as input. CFD simulations are time-consuming, but generating DPM concentration results with high accuracy. Besides, both monitoring points and planes can be created in a CFD model, which can take both point data and area-average DPM data as input. The hybrid methodology is intended to combine the advantages of the two by using the CFD results to update the network model results at key locations. A field study was conducted in a dead-end heading in an underground gold mine in the United States. Real-time DPM monitors were used to collect data. A CFD model and a network model were built for the experiment area. The CFD model was calibrated to the experimental data. In the study presented here, results from a calibrated CFD model are converted to equivalent diesel emission rates in the ventilation network model at a shared outlet. The hybrid methodology is used to provide better input for the network model. INTRODUCTION Mine ventilation system is one of the most important parts for an underground mine. It not only provides fresh air to the personnel but also helps clear the contaminants generated from the diesel-powered equipment. For most underground metal and non-metal mines, diesel particulate matter is the main contaminant. It is also the focus of this paper."

Jan 1, 2019

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the &apos;fine&apos; and &apos;coarse&apos; size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: > Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery > Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery > Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for fine, and &apos;coarse&apos; particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2013

By H. Willenberg, J. S. Coggan

ABSTRACT: Although individually both continuum and discontinuum numerical analyses provide useful means to analyze rock slope stability problems, complex failures typically involve mechanisms related to both existing discontinuities (i.e. discontinuum) and deformation and brittle fracture of intact rock (i.e. continuum). One such example is the 1991 Randa rockslide in the southwestern Swiss Alps, where failure involved several complex mechanisms, which require the consideration of progressive failure and rock mass strength degradation. This paper presents results from a series of hybrid finite-/discrete-element models directed towards the explicit modelling of brittle fracturing in natural rock slopes, enabling the modelling of progressive failure, from initiation, through to the development of catastrophic failure, transport and deposition. RÉSUMÉ: Si les modélisations numériques de type continu ou discontinu fournissent des outils utiles pour l’analyse de problèmes de stabilité de pentes rocheuses, elles montrent de sérieuses limitations lorsque des mécanismes de rupture complexes impliquent des processus liés autant aux discontinuités préexistantes qu’au développement progressif de nouvelles fractures. Ceci se retrouve typiquement dans l’exemple de l’éboulement de 1991 à Randa dans les Alpes suisses du sud-ouest, où la rupture a impliqué plusieurs mécanismes complexes nécessitant la prise en considération de la fracturation progressive ainsi que de la dégradation de la résistance des masses rocheuses. Cet article présente des résultats provisoires d&apos;une série de modèles hybrides orientés vers la modélisation explicite de la fracturation de pentes naturelles, permettant la modélisation de fractures progressive de leur initiation jusqu’à leur développement, leur rupture catastrophique, leur transport et leur déposition. ZUSAMMENFASSUNG: Obwohl numerische Kontinuum- und Diskontinuum-Berechnungen einzeln nützliche Ergebnisse zur Stabilitätsanalyse von Felshängen liefern, sind komplexe Felsrutschungen typischerweise mit Mechanismen verbunden, die sowohl durch bestehende Trennflächen (s.a. Diskontinuum-Ansatz) als auch durch die Deformation und das Versagen intakter Felsbereiche (s.a. Kontinuum-Ansatz) bedingt werden. Ein Beispiel für einen solchen Sachverhalt ist der Bergsturz von Randa 1991 im südwestlichen Teil der Schweizer Alpen, bei dem die Rutschung mehrere komplexe Mechanismen umfasste, so dass “progressive failure” und Verminderung der Gebirgsfestigkeit in Betracht gezogen werden müssen. Dieser Artikel beschreibt vorläufige Ergebnisse einer Reihe von hybriden Modellrechnungen (Finite-/Diskrete-Elemente). Diese haben zum Ziel, explizit das bruchhafte Versagen natürlicher Felshänge zu modellieren, wobei das progressives Versagen im ganzen modelliert wird, von der Anfangsphase über die Entwicklung zum katastrophalen Versagen und den Transport und die Ablagerung der Rutschmassen.

Jan 1, 2003

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By Fernando Henrique Gomes de Souza

Techniques which use a spring to supply the bias force to actuator are well adopted since they are inexpensive and simple to construct. In this work it was design an actuator concept using bias-type device technique, which comprises two coils that mutually push against each other to supply the stroke. For the coils springs, it was used a wire of NiTi shape memory alloys (SMA) and a wire of 400 grade maraging steel as construction materials.

Aug 8, 2018

By S. Gupta

Froth flotation is a process commonly employed for the selective separation of phosphate from unwanted mineral. Column flotation has become widely accepted in the mineral processing industry, including phosphate industries, due to its ability to improve selectivity, lower operating cost, lower capital cost, and superior control. In this work, a hybrid model is developed that combines a physicochemical model with artificial neural networks. The physicochemical model is based on axial dispersion with first order collection rates. A new approach, in which both frankolite (the desired mineral containing phosphate) and gangue (undesired product) are modeled, enables prediction of grade of the recovered product. Thus, two basic parameters are required in this model: flotation rate constants for frankolite and gangue. Artificial neural networks are used to predict flotation rate constants. The model also takes into account the particle size distribution and predicts grade and recovery for each particle size range. The model then combines grade and recovery for each particle size range to determine the overall grade and recovery of the column. The model is validated against laboratory column data.

Jan 1, 1998

By G Metzner, R Rodriguez, C Savage

OK Tedi Mining Ltd. (OTML) is in the process of optimising the concentrator performance. One aspect that has been recently implemented is an upgrade of the existing expert control philosophy on the grinding circuit and this will be the topic of this paper. Ore grinding in SAG mills is a multi-input multi-output (MIMO) process subject to several disturbances, most typical being quick acting disturbances such as changes in ore characteristics like hardness and particle size and slow acting disturbances such as ball charge variations and liner wear. The OTML SAG mills treat ore from diverse ore bodies and receive fresh feed subject to large changes in particle size. These circumstances make these mills particularly challenging to control. In this paper, a comparative analysis is presented between the performance of the OTML SAG mill #2 before and after the commissioning of a hybrid control strategy. The strategy uses Expert Knowledge combined with advanced disturbance rejection to reduce the variability of the main process variables, especially pressure and power. It further optimises the overall operation by driving the SAG mill #2 against process constraints (e.g. high power, high motor temperature and high scats recycle rate) and maintaining the operation at or near this point. This strategy is implemented by a combination of the manipulated variables (i.e. fresh feed tonnage and % solids) at any given time.The paper will present trends and a statistical analysis of the comparative results of the mill operation over a period of months, showing a 30% reduction in mill power / pressure variability and a 12% improvement in average power drawn. An increase in throughput was also observed, but cannot be conclusively attributed to the change in mill control due to other changes that were made to the SAG mill #2 during the period of comparison. An additional benefit includes better acceptance from the operators with improved consistency of the SAG mill #2 operation across shifts.The paper will also discuss further improvements envisaged in the continued optimisation of the grinding control circuit.CITATION:Savage, C, Rodriguez, R and Metzner, G, 2013. Hybrid process control strategy for the Ok Tedi Mining Ltd semi-autogenous grinding mill #2 - A comparative analysis, in Proceedings MetPlant 2013 , pp 202-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Jéssica Vicente Luiz, Rayander Martins Pimenta, Everton Pedroza dos Santos

The Hybrid Pelletized Sinter (HPS) is a agglomeration process that involves the combination of conventional sintering and pelletizing techniques and can be used with the purpose of obtaining improvements in the agglomeration stage of iron ore, and one of the great advantages of the process is the use of a wide particle size range of the ore. In this way, the superfines of low-cost ores, which are improper in sintering, can be used in the HPS process for the formation of the quasi-particle. The use of HPS with the sintering plants of the industries presented throughout the study, enabled an increase in productivity, decreased fuel utilization and reduced slag formation in blast furnaces. Thus, the present study aims to present a review of the literature on the Hybrid Pelletized Sinter (HPS) process and its main characteristics, as well as the results obtained by the companies that adopted the process.

Oct 1, 2019