Search Documents

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By R. J. Bethancourt, D. M. Collingwood

The use: of a pilot waterflood is very desirable where all of the pertinent data necessary to initiate a full scale waterflood are not. available. This paper attempts to take a specific case and .show the step by step process of starting with a pilot waterflood and progressing to a full wale flood as results are obtained. INTRODUCTION Many of the older fields of Soutlwest Texas are approaching depletion by primary produrtion methods. As primary protlllc:inp operations on individual properties approach their economic limit. conflicting considerations face management: cm the one hand. plugging and abandonment of wells for equipment salvage; on the other hand, further investment in secondary recovery installtions, equilent, and well workovers in the interests of conservation anal additional oil reserves. In main instances, where primary production by pressure depletion and gas solution drive has been comparatively good, there still exists the possibility of an economic secondary recovery by waterflood. This is not necessarily true to the same degrre of all such fields. nor all portions of large fields. To properly evaluate the economics of a prospective water-11ot1cI requires a considerable amount of precise geological. statitical. and physical data Such information on the older field.; is often very limited. and in the case of the property discussed in this paper was considered inadequate to justify investment in an overall waterflood. Primary production was estimated at :39 per cent of the original oil in place, yet sand conditions of permeability and homogeneity, and position in the field appeared to be favorable for a limited margin of profit from a carefully controlled waterflood. Thus a pilot waterflood, with its minimum initial financial risk, followed by extension as favorable results were obtained, seemed to be the answer for the Sun Oil Co L. Wiederkehr lease in the Nortl Government Wells Field, Duval County. Texas DESCRIPTION OF RESERVOIR Approxinately 8,200 wells have been drilled in Duval County. As of March 1, 1952, there were 3,350 producing oil wells in 92 different fields, with very few flowing wells (Fig. 1.) Sun Oil Co. operates the I.. Wiederkehr lease located in the North Government Wells Field in Duval Countv. 85 mile. west of Corpus Chriti and 100 miles south of San Antonio. The lease has been subjected in part to a controlled five spot waterflood. The North Government Wells Field is roughly 7 miles long and 3 miles wide, with numerous overlapping producing zones. The L. Wiederkehr lease of 3.085 acres. Has seven producing zones from 700 to 7.500 ft. The lease is in the northern section of the field where it is widest, and has 710 acres productive from the North Government Wells .and. (Fig. 2.) The North Government Wells sand, Jackson group. Eocene age, at an average depth of 2.250 ft (minus 1.750 subsea). has a thickness range of 25 ft on the east side of the L. Wiederkehr lease to 4 ft on the west side. It has a slight overall dip to the North and East of some 33 ft to the mile.

Jan 1, 1953

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By Y. Hanada

Electrorefining at higher current density is desirable due to the increase in productivity attained without expanding the plant size. However, increasing the current density in common commercial practice causes problems such as anode passivation, dendritic deposition, cathode impurities and energy consumption. In general, agitation of the electrolyte is effective in suppressing these problems. To apply the agitation to commercial practice effectively, the method of agitation is important. One possible method is agitation by gas injection. In this study, fluid motion characteristics with gas injection between electrodes were investigated using a water model. Flow patterns were observed and fluid velocity was measured using a particle tracking method. It was found that the time-averaged velocity near the electrode walls was of the order of 0.1 m/s in the conditions. The flow was highly turbulent. The turbulent component of velocity was the same order as the time-averaged velocity. The mass transfer coefficient between the wall and fluid doubled when the effect of turbulent intensity was taken into account. The effects of gas injection on the electrolysis behaviour at high current density were discussed in terms of the mass transfer. It is suggested that gas injection could suppress the problems at high current density.

Jan 1, 2007

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By William A. Kennedy, Jonathan R. Stahl

This paper deals with the phenomenon of water held in a leach dump due to capillarity. Water is shown to be retained in the fine pores of the ore as well as in the interstices between the rock and soil particles. Upon drainage, Chino leach dump material shows two distinct capillary systems and a double capillary curve is often obtained. Both the igneous and the sedimentary rocks composing the leach material are shown to have appreciable porosity but little permeability. Fluid flow is, therefore, restricted to the interstices between the rock and soil particles. The irreducible water saturation for the aggregate is found to be 884 for the -48 mesh material and 235 for the448 mesh to one inch material. The composite sample of minus one inch dump material had an irreducible water saturation of 52 percent. The irreducible water saturation in the fine pores of the ore was found to be between 73 and 76 percent. Very coarse pores or channels between large rocks exhibit essentially zero capillary retained water. The presence of fine material in a dump can cause high water saturations to be retained and these saturations may be mistaken for perched water tables. Perched water tables can be drained but capillary water will be retained. Capillary pressure data can aid in distinguishing between perched water tables and capillary retained water.

Jan 1, 1974

By Quintiliani G, Giordano V

A research field of interest and a topical subject with the aim to reduce a considerable amount of coke in ironmaking is the injection into blast furnace stack of hot reducing gas combined with use of auxiliary fuels at tuyeres. In recent years evaluation studies and prelimirfary industrial experiments have been carried out on this subject in Europe and Japan. Even if these experiments seem to confirm the advantages theoretically expected, it appears as useful to cast more light on new problems concerning the improvements of this technique. In this report some aspects are analysed on fluid dynamics of blast furnace process with two gas flows: the main flow coming from the bosh and cross flow of the reducing gas injected in the lower shaft. A research on a blast furnace physical model was made with the aim to obtain information about the phenomena which occur in the full scale blast furnace. This work was carried out on cold models IN and tridimensional) in which the radial gas distribution was experimentally measured. A mathematical model based on gas diffusion was implemented aimed at simulating gas distribution inside the reactor taking into account the number of injection tuyeres. A good agreement between experimental and theoretical data allows for extending results to industrial practice in order to determine operating conditions assuring good performance of blast furnace with high amount of auxiliary fuels.

Jan 1, 1975

By Andre Krzysik

"Fluidized bed technology has been used in the industry for almost 100 years. To fully understand the process hundreds if not thousands of researchers were and are involved in finding the way to predict the behavior of the solids when subjected to the flow of media through them and the conditions of the solids in the fluidized state. The difficulties in predicting the behavior of solids in the fluidized state stem from the complexity and abnormality of the parameters related to the solid particles. Theoretical calculations can in some degree account for some of them. Particle size distribution, their shape, density, moisture content and physical and chemical reaction that may exist in the fluidized bed reactor play an extremely important role and influence the behavior of the fluidized bed. This paper focuses on the practical examples of the fluid bed equipment and the use of different conditions to process various products.IntroductionEach process application has its own unique requirements and the designers of the equipment must take into consideration specific process requirements, specific properties of the material to be processed (both physical and chemical), and physical and chemical reactions/changes that are taking place in the reactor (heat and mass exchange, chemical reactions, isomorphic change etc.). Each individual piece of equipment must also satisfy specific requirements/ preferences of the client that will operate and maintain the equipment. Those often represent greater challenges than the process on its own, and are equally important to the satisfactory operation of the plant. That includes aspects like location of the equipment, environmental effects, and expected life of the equipment, process control, access, maintenance, and many others.Over the period of time a great deal of research, both theoretical and practical have been carried out and the results of that work are available for equipment designers. For the simple applications that information is usually sufficient and the selection of a suitable solution is relatively simple. In many instances, the available information is not sufficient, and often specialized test work needs to be conducted to obtain additional data. In many cases a pilot installation is built in which the required process is tested. Only then the commercial equipment is designed. The following deal with specific installations that were designed to satisfy specific requirements. In some instances, additional problems were discovered during the commissioning of the equipment that required on site modification. The continuous monitoring of the equipment that was supplied to the various clients allowed us to further develop and improve our designs."

Jan 1, 2014

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By Y. Zhang, F. Zhu, Y. Zhao, L. Dong, Y. Li

In order to obtain a more suitable separation medium for fine coal, in this paper a pulsed fluidised bed was used to measure the pressure fluctuation, density characteristics, bubble diameter and rising velocity of Geldart A and B particles in the bed by controlling the pulsation frequency and gas velocity, in order to study the fluidisation effect and two-phase distribution of the bed. The results indicated that with the increase of pulsation frequency, the breakthrough point on the fluidisation characteristic curve caused by particle adhesion disappeared, and there was an optimal frequency, which made the minimum fluidisation velocity of particles reach the minimum. In addition, the bubble rising velocity was also simulated. The relationship between them was established using a model, and the error was within 5%. This provides an effective way to predict the bubble velocity, study the distribution of bubble phase, and improve the stability of bed density. Keywords：Frequency, flow velocity, pressure fluctuation, bed density, bubble

Jan 1, 2020

By Z. Luo, W. Chen, Y. Zhao, Y. Fu, L. Dong

The gas-solid dense-phase fluidised bed includes a complex multiphase fluid-particle system; different complex exchanges significantly affect the stability of the fluidised bed. To elucidate the characteristics of fluidisation in a gas-solid dense-phase fluidised bed, this study used experimental performance tests to obtain the static density characteristics, and the attachment and flow characteristic of the dense medium. The results indicate that the bulk density of the dense medium increases first and then decreases with the increase of particle size. The airflow rate difference is used to quantify the wall attachment characteristics of dense medium and the average pressure gradient in the axial direction of the bed is approximately 20 Pa/mm under the fluidisation results. At the same settlement location, with the decrease of fluidisation number, the settlement velocity of large and small particles becomes slower, the boundaries of settlement displacement and location probability are gradually disrupted, and the falling velocity of particles with a radius of 20 mm is faster than that of materials with a radius of 15 mm. This work also established a theoretical basis for regulating the stability and separation characteristics of gas-solid dense-phase fluidised bed. Keywords: Fluidised bed, different size particles, fluidisation characteristics, flotation bubbles, settling motion

Jan 1, 2020

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By A. D. Engelbrecht

An investigation was undertaken to ascertain the suitability of four selected low grade, South African coals for gasification in a bubbling fluidized bed for production of synthesis gas and for the development of integrated gasification combined cycles (IGCC). This study consisted of the characterization of the coals, laboratory evaluation of intrinsic reactivity, and experimentation with a pilot-plant fluidized bed gasifier. Results of the characterization experiments show that the selected coals are high in ash, rich in inertinites, very dense (low porosity), with low caking indices and high ash fusion temperatures. Reactivity measurements with a thermogravimetric analyser (TGA), under reaction rate controlling conditions with carbon dioxide, showed that the reactivity of the coal chars decreases with increase in rank of the coal, as expressed by the vitrinite random reflectance and carbon content of the parent coals. The fixed carbon conversion achieved in the fluidized bed gasifier also correlates well with the rank parameter of the coal, with higher conversions being obtained with the lower rank coals. Thermal shattering and attrition of the coal particles produce significant amounts of fines, which correlate with the grindability indices, and no agglomeration (non-caking) was observed. It is concluded that fluidized bed gasifiers are able to utilize typical low grade, high ash South African coals for synthesis gas production and for inclusion in integrated gasification combined cycles for power generation.

Jan 1, 2010

By E. Eccleston, E. Gardner, F. Letarte, R. Schonewille

"In 2005, after nearly a decade of process development and feasibility work, the commercialization of the Falconbridge Nickel Smelting Technology (NST) began in earnest with the design and construction of a grassroots ferronickel plant at Koniambo Nickel in New Caledonia. The NST process was developed as an alternative to the conventional Rotary Kiln-Electric Furnace (RKEF) process for production of ferronickel from saprolitic nickel laterite ores. The NST process promised environmental and energy efficiency advantages over the conventional route. A key step of the NST process involves fluidized bed pre-reduction of calcined laterite ore using direct injection of pulverized coal as the reductant. Two parallel fluidized bed reduction roasters (FBRs) were installed at Koniambo Nickel, each designed for a maximum capacity of 4,200 MTPD of calcined nickel laterite ore. This paper describes the process development and scale-up of the fluidized bed pre-reduction process, the design challenges associated with the prototype commercial units, and the current status of the FBR operation at Konaimbo.INTRODUCTION In the mid-1990s, Falconbridge began to develop a new flowsheet for production of ferronickel from nickel laterite ores. The process that developed came to be known as the Falconbridge Nickel Smelting Technology (NST). The flowsheet, which is particularly appropriate for saprolitic ores, involves several major unit operations, including: drying in a hammer mill-flash dryer, calcination and preheating in a flash calciner, pre-reduction in a fluidized bed reactor, and smelting in a DC arc furnace to produce the ferronickel product. This paper focuses on the fluidized bed pre-reduction step of the process and provides an overview of the process chemistry, laboratory and pilot plant development work, scale-up and commercialization of the pre-reduction step, and the results obtained in the prototype commercial units."

Jan 1, 2017

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil Corp. (now part of Atlantic Richfield Co.) in the period 1.965 to 1968. The results of the work show that presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. This has implications for several types of retorts. Correlation of the results of this work with that of other investigators shows that the partial pressure of retorting products in contact with oil shale during retorting has an effect on yield. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to await commercialization of another process. The existence of a plant in which to test prototype size would markedly reduce such development costs. Results Preliminary development work with the apparatus was carried out using a fluidized bed of sand, as explained later, with the entire system brought up to temperature and flows stabilized. The shale was injected rapidly in a slug (batch) which had small mass compared to that of the high temperature system to make the reaction approach isothermality with reasonable approximation of instantaneous preheating. Typically, the temperature in the center of the bed dropped from 900°F to 600°F one minute after batch addition. It returned to 750' within three minutes and 900° within seven minutes. Obviously, the bed was quenched but it recovered rapidly. Average bed temperatures of 700' to 1020°F were examined to compare the effect of temperature with published results. Yields In the 700°F range were only 10 to 15%, of Fischer Assay (FA). Above about 950'F, oil yields decreased and gas yields increased. Nitrogen was used first as the fluidizing gas to provide a chemically inert medium. Incept for an insignificant dip at 895"F, Figure 1, oil yield was not affected by retorting temperature in the 800° to 900' range as long as residence time was adequate (16 minutes). At 925°F, the oil yield was some 103% FA. With further increase in temperature, the yield decreased to 86% FA at 1015°F. There is no increase in carbon on spent shale, the lost oil goes to Increased gas make.

Jan 1, 1972

By Urie R. W

Fluidized bed roasting of copper concentrates from Mt. Morgan, Mt. Lyell, Mt. Isa, and Peko was performed in a 3 ft 6 in diameter, slurry fed, pilot plant roaster operated under autogenous conditions to produce calcines with desirable leaching properties. A 12 in. diameter, externally heated roaster, provided with a dry feed system, was also used.An account is given of important factors which influence roaster behaviour and performance, and the effects of operating variables on calcine composition and leaching properties are described. Due to copper ferrite formation, a maximum of approximately 50 per cent of the copper in the calcines may be in the form of CuO before the copper leach efficiency falls significantly below lOO' per cent. Recovery of gold by cyanidation of leach residues was consistently high and independent of roasting conditions.INTRODUCTIONIn traditional practice copper is produced by pyrometallurgical techniques when the ,copper minerals in the ore or concentrate are predominantly sulphides, and by hydrometallurgy when the minerals are oxidized. Copper smelting is most suited to large scale operations, and for many years small to medium size mines with sulphide orebodies have been interested ill; alternative processes.Since hydrometallurgical plants (ie. leaching and electrowinning plants) are essentially unitized, they may be scaled down in output without much loss in efficiency or increase in processing cost, and many proposals have been made for the application of this type of process following roasting of the sulphides to render the copper soluble. However, until the advent of fluidized roasting, it was not possible to control the roasting operations sufficiently precisely to produce calcines consistently of the required leaching characteristics.

Jan 1, 1961

By S. Heukelman

Zinc or, a zinc refinery in South Africa, uses oxygen enrichment of up to 26% O2 in its fluidizing air to increase concentrate-throughput in its fluidized bed roasters. The aim of the study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining concentrate throughput rates and calcine quality. A laboratory scale fluidized roaster was used to determine the strength and oxidation kinetics of suitable micro-pellets. The strength of the pellets was determined by the extent of attrition during roasting. It was found that micro-pelletization decreases the fines in the feed to the roasters; the ?500 µm fraction decreased from 87% to 10%. The micro-pelletized particles do break down during roasting, which increases the -500 µm fraction to 31%. The general morphologies of the roasted particles are similar to those found by previous workers. Micro-pelletized concentrate particles require more time than non-pelletized concentrate particles to oxidize in the roasting step, although this is less than the mean residence time of the Zincor roasters. Roasting micro-pellets in O2-enriched fluidizing air increased the reaction rate.

Jan 1, 2011

By S. Heukelman

Zincor uses O2 enrichment (up to 26% O2 in the fluidizing air) to increase the processing rate of zinc concentrates in the fluidized bed roasters. The aim of this study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining current roaster feed rates and calcine quality. It was found that, with a load of 20% micro-pellets introduced into the feed blend, that O2 enrichment could be reduced by 60%. It was determined that entrained particles spend on average between 0.46 hour and 2.44 hour in the roaster, compared to particles remaining between 3.93 hour and 4.00 hour in the bed overflow. This compares well with a radioactive tracer test performed by Spira. The required reaction time for micro-pellets was found to be less than the residence time inside a Zincor roaster. The result achieved indicated that the average particle residence time inside the roaster was increased successfully in order to compensate for the longer reaction time required to roast micro-pellets at lower levels of O2 in the fluidizing air.

Jan 1, 2011