Search Documents

By C. Schlumberger

THE object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,1 but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding?2 method, in which a series of measurements are made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is deter-

Jan 1, 1934

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997

By Erich Sarapuu

Today's increasing needs for rapid excavation have stimulated efforts to break rocks without explosives. The application of electric energy for this purpose has been studied by a number of investigators. Following principles have been used in electrical rock breaking: 1. induction heating5 2. high frequency heating4, 14 3. microwave heating6 4. contact resistance heating9,12 5. resistance heating11,13 6. electron beam heating1, 3 7. plasma jet heating2, 8 8. arc heating7 9. condensor discharge energy14 In this paper the presentation of the principles of electrical fragmentation is limited to a process called "electrofracing". This technique uses electrical heating of rock by electrode contact resistance9 and resistance heating" phenomena. The electrically induced stresses inside of rock generate forces which break up the material. The fracturing of ore takes place by tensile stresses instead of compressive forces. The electric energy merely creates fractures in the rock and the separation of fractured material takes place by subsequent mechanical handling. Energy requirements in secondary breaking of iron ores have been about one to two kilowatt-hours per ton of ore. Power requirement is a function of the degree of fragmentation.

Jan 1, 1969

By F. G. Cottrell

(New York Meeting, February, 1912.) ABOUT a year and a half ago, at the San Francisco meeting of the American Chemical Society, in connection with the excursions to local smelting-works, I had occasion to show some lantern-slides illustrating the recent commercial development of electrical methods for precipitating the suspended matter from smelter-smoke, the underlying phenomena of which were clearly brought to the attention of the technical public by Sir Oliver Lodge as long ago as 1884. In the Journal of industrial and Engineering Chemistry, August, 1911, most of these views were reproduced, together with an account of the work from its beginning up to July, 1911. To-day I wish particularly to show you some of the further developments of the work since that time; but in order to make these clear they will be prefaced by a brief abstract of the article above referred to. The removal of suspended particles, front gases, by the aid of electric discharges is by no means a new idea. As early as 1824 we' find it suggested by Hohlfeld 1 as a means of suppressing ordinary smoke, and again a quarter of a, century later by Guitard.2 These suggestions, which do not seem to have stimulated any practical study of the question, were soon entirely forgotten, and only brought to light again by Sir Oliver Lodge,3 many years after he himself had independently rediscovered the same phenomena and brought them to public attention 4 in a lecture before the Liverpool Section of the So-

Jul 1, 1912

By J. C. Cawley, G. T. Homce

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) conducted a study of mining industry electrical injuries reported to the U.S. Mine Safety and Health Administration (MSHA) for the years 2000 to 2009. The findings of that study are detailed in this paper, and serve to characterize the circumstances surrounding electrical injuries and identify causal factors. The study included three tasks: 1) a direct review of mining industry occupational injury data compiled by MSHA, 2) interpretation of the narrative descriptions available for the injuries (from MSHA data) and 3) a separate examination of fatal electrical injuries. Eight-hundred sixty-five electrical injuries were reported during the 10-year period studied, with 39 of those being fatalities. This makes electrical injuries disproportionately fatal with respect to most other types of injuries in mining. Electrical injury rates were higher in coal mining than noncoal mining and, within the coal sector, rates were higher in underground operations than in surface operations. Of the 865 total cases, electrical and machine maintenance or repair activities were involved in 580 (69%), and electricians and mechanics were injured in 362 cases (42%). Of the 39 fatal electrical injuries, 27 (69%) involved electrical maintenance or repair work, and in 21 of these 27 cases, the failure to de-energize, lock-out and tag the circuit was the cause or a contributing factor. Also, contractor employees had a much greater chance of an electrical injury being fatal than did mine operator employees. The top three root causes for fatal electrical injuries were 1) no or inadequate lock-out and tagging, 2) failure of power system components and 3) contact of overhead electrical power lines by mobile equipment.

Jan 1, 2013

By B. R. Coil, C. A. Ross

NEW demands for underground power in the Miami mine of the Miami Copper Co., Miami, Ariz. has brought about expansion of the distribution system for both ac and dc power. Progress in mining equipment and the normal changes in the mine were responsible for this increased demand. Early power requirements were for pumping and haulage. A 440 v ac power line down No. 5 shaft took care of a small pumping load and shaft station lighting, 275 v dc power was generated by motor generator sets on the surface, with a churn drill hole from surface to the 570 haulage level serving as a cableway. Electric lights were installed where power was available, and thus were confined to the haulage level and shaft stations. All industrial power in the Miami area is 25-cycle, which dates back to the hydroelectric generator installation at Roosevelt Dam in 1908-10. The Problem The main haulage level was moved to the 720 level and later, to the 1000 level, requiring a longer feeder line with the resultant voltage drop. Also, as mining progressed to the east, the churn drill hole for the power cable would have been subjected to subsidence cracks. The first extension in the use of electricity was in electric blasting. About 1935 the mine went to electric blasting, using the dc haulage current. Bringing electric current to the working levels of the mine for blasting greatly expanded the use of electric lights. Lights were used in tool rooms, powder and cap magazines, stairways, and other semi-permanent installations. Like all mines, Miami Copper began to study and experiment with mechanical mucking and transportation of ore by slushers, shakers, and belts during the late 1930's and early 1940's. At the beginning of the program, power was supplied from the haulage level 275 v dc system. Later it became necessary to run a cable, carrying 440 v ac power, down the No. 7 ventilation shaft. The increased use of power came about gradually, and many new problems were added, not the least being the introduction of switch boards and power cables into the working areas of the mine, where drifts and crosscuts take weight, and require repairs. The 25-cycle current presented special problems, in that 25-cycle transformers are twice as large and about 2V2 times as heavy as 60-cycle transformers of the same power output. The 25-cycle transformers were considered too large for installation in the mining areas. In 1947 the distribution system was revised and standards were adopted, governed by the following

Jan 1, 1952

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By Nikolay Boykov

Subsurface imaging technologies are part of the electromagnetic (EM) geophysical methods. EM technologies such as radio imaging method (RIM), ground penetrating radar (GPR), and drill string radar (DSR) have great application potentials in the mining industry. However, the success for applying the EM methods to subsurface observations is largely dependant on the correct evaluation of the electrical properties (i.e., resistivity and dielectric constant) of the rocks in the domain of interest. The depth of penetration of the EM signal in coal, as well as the electrical contrast between coal and subsurface boundary rocks or anomalies, are critical parameters for any successful radar system. Based on the measured electrical properties of the coal seam, the proper operating frequency of the radar system must be chosen in order to successfully detect features such as the coal-roof rock boundary, dykes, and voids ahead of mining. The electrical properties of the rocks in a coal seam are frequency dependent. Even though there has been a great advancement in the hardware and data processing software in the past twenty years, there have not been many examinations of the high-frequency properties of coal measure rocks. In this paper, the laboratory setups, the testing procedure, and case studies will be presented for a wide spectrum of frequencies for coal measure rock samples collected from various US coal fields. Tests have been conducted to study the different conditions, including moisture content, that affect the EM properties.

Jan 1, 2006

By S. C. Richardson

The electrowinning (EW) circuit involves using DC current in the electro-deposition of metal ions dissolved in an electrolyte solution. This paper reviews a method to generate an electrical model of an EW circuit and the resulting DC current flow and voltage distribution within the circuit. Topics include: calculations of electrolyte conductivity and the equivalent electrical resistance of the electrolyte within the electrolyte pipelines connected to the EW circuit; the breakdown and classification of the EW cell voltage into thermodynamic and ohmic potentials; methods to calculate current flow and voltage distribution throughout the EW circuit; and the development of an interactive visual computer model to simulate an actual EW circuit. Stray current can pose an electrical shock hazard to employees in electrolytic tankhouses. Increased awareness and understanding of the voltage distribution and potential stray current in an EW circuit can help mitigate the risk of tankhouse workers becoming exposed to electrical shock hazards. INTRODUCTION Copper electrowinning tankhouses include rectifiers that deliver large amount of DC current to a series of electrolytic cells consisting of electrolyte solution and electrode pairs. The design also includes metallic conductors in the circuit which include the rectifier’s positive and negative busbar, inter-cell busbar, and the anode and cathode frames. The electrolyte acts as an electrical conductor that transfers current via ions between the anodic and cathodic electrodes within the cell. Electrolyte, as a conductor, is also capable of conducting DC current outside the main EW circuit through the connected electrolyte feed and return pipe systems. DC current that follows a path other than the intended path through the series of electrolytic cells is referred to as “stray current”. Developing an electrical model enhances understanding of voltage distribution and current flow in an EW circuit. This paper discusses the derivation of the various representative components of the model as well as the output from the model. An interactive visual computer simulation incorporates the model output in order to aid in the understanding of voltage distribution and current flow throughout the EW circuit.

Jan 1, 2019

By B. C. Morrison

Because of U.S. Forest Service regulations and the consequent cost of leaving several diamond drill holes open at the same time, it was necessary to develop an electrical method that could be used in one hole at a time to extend known mineralization. This was achieved by balancing the surface current electrodes so that the two potential electrodes in the hole being surveyed were in the same equipotential surface. This condition eliminated stratigraphic response but enhanced any asymmetry due to ore between the hole and either current electrode. This method was successfully used in mineralized holes at West Fork, Reynolds County, Mo., to show the direction in which to extend the drilling into areas of better mineralization.

Jan 1, 1972

By C. F. Starr

This paper deals with the various types of cable in use in mines, with special attention paid to their construction. There will be a few comments regarding the different insulants, jacketing materials and armouring used, depending on their application. Governing standards and the differences therein will also be discussed.

Jan 1, 1969

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014

Dielectrophoresis is a separation technique that uses a non-uniform electrical field to separate particles on the basis of their permittivity. There are many areas of mineral processing that might benefit from the application of dielectrophoresis. These include: coarse removal of gangue, recovery of ultrafine particles, upgrading of flotation concentrates or simply as a laboratory analysis technique. In order to determine the potential value of dielectrophoresis to the mineral processing industry, the response of composite particles was investigated. The electrical properties of composites involve complex relationships between the shape, distribution and permittivity of the individual grains within the rock. The relationship between mineral composition and dielectrophoretic force was measured on single particles from two ore types. The results were used to populate a model that could predict the separation characteristics of the ore. The insights gained from this model separator allowed potential applications of the technology to be examined and their performance evaluated.

Sep 1, 2012

By Irving Crosby

ELECTRICAL prospecting by potential methods has been applied to mining problems for some years and determinations of the depth to bed rock have been made, but so far as is known it has not been used previously in the solution of civil engineering problems, such as investigating the foundations of dams. During the past winter and spring the senior author has been engaged as consulting geologist in studying the site of a large darn on the upper Connecticut River and has had the satisfaction of introducing electrical prospecting to foundation problems. The valley across which the dam is to be built is underlaid by a deeply buried preglacial gorge which is filled with glacial deposits. An extensive drilling campaign was in progress, but the work was unusually slow and expensive on account of the number of boulders in the overburden. The necessity of speeding up the work was pressing and it was decided that much of the needed information could be obtained by geophysical methods. After investigating the various methods and conferring with the company engineers and with the consulting engineer, Albert Crane, a contract was made with the Schlumberger Electrical Prospecting Methods, and an observer with apparatus was sent to the dam site the first of April, 1928. The problem was to determine the depth to rock at various points in order to prepare a contour map of the bed-rock surface and outline the buried gorge in the vicinity of the dam site. Over one hundred determinations of depth have been made and the bed-rock topography, is now known in considerable detail. In addition, some information has been obtained about the nature of the overburden. The drilling has been continued; in fact, two additional drills have been put to work, and the electrical determinations have been checked at several points. At one of these the depth to rock given by the electrical work was 142 ft. and the drill found rock at 147 ft., an error of less than 4 per cent. The electrical work has also been checked by the geological study, and it has been found that when the electrical determinations are in agreement with the geological expectations they are probably reasonably accurate. When the electrical interpretation of the sub-surface topography is incon-

Jan 1, 1928

By Hans Lundberg

GEOPHYSICAL methods as described in technical articles generally fail to answer the questions of prospectors and geologists as to which method they should apply and what information they may expect from their application. This article is an attempt to discuss the use of electrical methods with special reference to the prospecting for orebodies and the map¬ping of geologic structure. Especially on virgin ground, geological reconnaissance should precede electrical prospecting, with the object of outlining carefully the orebearing rock and determining the possibilities of elec¬trical prospecting. No electrical survey will then be carried out on ground which, for geological reasons, may be considered barren or where the electrical meth¬ods are inapplicable. As the success of electrical prospecting depends on the difference in conductivity between the ore and the country rock within which the orebody is inclosed, the conductivity of the two should be considered and de¬termined, if possible. The conductivity of an orebody depends on the distribution of conductive ore minerals and, in addition, on its size (length, width and depth). Most minerals with metallic luster show good electrical conductivity; for instance, the sulfides. Zinc-blende is an exception, but as it is often associated with the ore minerals of good conductivity (for instance, pyrite or galena), there is likelihood also of finding zinc.

Jan 1, 1930

By Sherwin F. Kelly

With the progressive exhaustion of ore deposits easily discovered by surface prospecting, the attention of scientists is being turned more and more to the employment of mechanical means for the location of ore bodies whose outcrops are not visible. The dip needle, the Eotvos Torsion balance, and various methods of electrical prospecting are illustrative of the modem tendency. Interest in the possibility of applying electricity to the solution of many of the prospector's problems dates much farther back than is usually realized. The first person to notice an abnormal intensity of electrical activity in the region of certain ore bodies was an Englishman, R. W. Fox, who experimented on the Cornwall copper and tin veins about 1830. Dr. Barus, in the United States, carried the early experiments a step further in his work on the deposits of Eureka, Nevada, about 1880. He made the very definite suggestion that the phenomena noticed would be of material aid to the prospector. Not until Professor Schlumberger, of the Ecole des Mines, Paris, took up the matter, shortly before the war, was any definite effort made to put electrical prospecting on a commercial basis. His work resulted in the establishment of sound principles and practicable field technique, for two distinct methods of prospecting.

Jan 1, 1924

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By D. Odendaal, S. Bharat, R. D. Cromarty

The aim of this investigation was to determine the effect of high-temperature heat treatment on the electrical resistivity of charcoal. Samples of two different wood types (eucalyptus and black wattle) were pyrolised in a retort at a temperature of 700°C and the resulting charcoals heat-treated in an induction furnace at temperatures from 800°C to 1800°C and residence times from 60 to 120 minutes. After cooling, the resistivities of the samples were measured at room temperature using the four-point probe technique. It was found that as the heat treatment temperature increased the electrical resistivity of the charcoal decreased, approaching an asymptotic value at higher temperatures. Longer residence times decreased the resistivity, but this effect was not pronounced.

Oct 3, 2023

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By M. J. Sheriff, D. H. Smith, W. Macdonald

The paper outlines the basic procedure used in electrical system planning and design. Consideration is given to the use of applicable codes and standards, development and use of a system One Line Diagram, power availability, load requirements and power factor. Also discussed are the factors influencing the selection of power supply and distribution arrangement, voltage levels, system grounding, distribution and utilization equipment such as switchgear, transformers, motor control, cable systems, motors. Short circuit calculation methods and system protection are discussed.

Jan 1, 1978