Search Documents

By Hideo Nakae, Hideki Yamaura, Toshiaki Kimura

"In 1968 J. N. Reding et al. suggested processes for fabricating composites. According to their patent, decompression atmosphere, which occurs during the reaction between magnesium and oxygen and/or nitrogen in the closed system, causes the spontaneous infiltration of melt into narrow spaces such as ceramic preforms. However, they did not report the proof of this phenomenon or the industrial manufacturing method. Therefore, this research measured the pressure change among SiC particles surrounding molten aluminum. As a result, the pressure reduction during the Mg reaction was identified. Moreover, the existence of Mg3N2, which improves the wettability between Al alloy melt and SiC particles on the interface, was observed on the surface of particles. Applying these two phenomena, a new process for the manufacturing of cast discontinuously reinforced aluminum composites (DRA) was developed. This new method is expected to produce DRA without additional pressure.IntroductionWith the increasing demands for light-weight materials in the automotive and aerospace industry in recent years, ceramic particulate reinforced aluminum matrix composites called DRA (Discontinuously Reinforced Aluminum Composite) have been receiving significant attention because of its lightness, superior abrasion resistance, high heat conductivity and low thermal expansion [1-3]. Consequently, DRA was considered for electronic parts such as heat-sinks or a base for power semiconductors, and began to be applied for automotive parts including brake drums, discs, cylinder liners, pistons and so on [4- 6]. However, high machining cost is one of the significant barriers to widespread use ofDRA. One solution to this problem is the adoption of cast DRA that can be produce to near-net shape, reducing machining cost."

Jan 1, 2000

By Osamu Takai, Yoshiki Sato, Nobuhiro Tajima, Hiroyuki Sugimura

"Amorphous carbon thin films doped with nitrogen ( a-C:N) have been synthesized by means of shielded arc ion plating (SAIP). Their electron field emission properties, that is, threshold field strengths for electron emission and maximum emission current densities, were evaluated and compared with those of pure amorphous carbon (a-C) films prepared by the same SAIP apparatus. Among all of the fabricated a-C:N films, the a-C:N films with a N concentration of 23 %, which prepared using Nz arc plasm at a pressure of 1 Pa with applying a sample bias voltage of -100 V, showed the lowest threshold filed of 13.4 V/µm and the highest emission current density of 1.87 µAfcm2 at a field of20 V/µm. These field emission properties of the a-C:N film were much better than those of the a-C films. The best results obtained on the a-C film in this study were the lowest threshold filed of 15.5 V/µm and the highest emission current density of 0.052 µA/cm2 at a field of 20 V /µm. Nitrogen doping to aC was found to be effective for lowering threshold voltage for field emission and for increasing emission current density. The electron field emission characteristics of the a-C:N films depended not only on N concentration but also on chemical bonding state of nitrogen in the a-C:N films. The presence of the ~-C3N4-like phase, which contributes to improve wear resistance of a-C:N as well, distinguished by the NlsXPS peak at 400.5 eV is proved to be crucial in order to enhance field emission properties of a-C:N.IntroductionThere has been much interest in electron field emission from a cold cathode due to its potential applications in vacuum microelectronic devices including field emission displays which are expected as flat panel displays in next generation [l]. It is well known that efficient emission can be rather readily realized using tip-like shape cathodes, e.g., microfabricated three-dimensional electrodes [2], carbon nanotubes [3-5], etc. However, electron emission from planar surfaces is of particular importance since such a type of cathode is· simply fabricated and assembled into microelectronic circuits. Currently, amorphous carbon thin films doped with nitrogen (a-C:N) prepared by plasma processes have attracted attention because their threshold voltages of field emission are relatively low [6]. Among various methods for preparing a-C:N films, the process using arc plasma is of special interest since, in arc plasma, nitrogen is highly activated and new types of carbon nitride phase are expected to be synthesized. However, field emission properties of a-C:N prepared by arc plasma have been studied in less detail compared with that prepared by the other methods such as sputtering."

Jan 1, 2000

By Gong-yi Guo, Yu-li Chen

"A partially-stabilized zirconia powder was prepared by metalorganic precipitation process from technical-grade zirconium oxychloride and the effluent of an acrylic acid plant. The effluent contained low molecular weight carboxylic acids, i. e., acrylic acid and acetic acid. The· developed process is based on the selective precipitation of acrylic acid at suitable pH values by the addition of zirconium oxychloride to the effluent. The resulting precipitate is a precursor that can yield a pure, ultrafine, and partially-stabilized zirconia powder. The evolution of formation of the partially-stabilized zirconia in the present process was investigated using thermal analysis, infrared spectroscopy, and X-ray diffraction technique. Environmental, technological and cost advantages will make the present process feasible for manufacturing advanced zirconia ceramics.IntroductionIn recent years the superior mechanical, thermal, electrical and chemical properties of stabilized zirconia have become the focus of growing scientific and technological interest, and hence resulted in various structural and functional applications. The great potential of the material has given rise to numerous preparation approaches to obtain the material with the excellent properties; nevertheless, an extensive number of programmes are underway worldwide aimed at understanding and improving both the preparation and behavior of stabilized zirconia ultrafine powders. (1 – 8)."

Jan 1, 2000

By Antti Roine

HSC Chemistry is a widely-used therniochemical tool in the chemical and metallurgical industries and in universities. The main reasons for it's popularity is the easy user interface and the large integrated thermochemical database. This paper summarizes the main properties of the new HSC Chemistry version 3.0, and gives a short review of the new features: Some metallurgical applications with the new features are also presented. HSC Chemistry 3:0 contains seven calculation modules and a thermochemical database with more than 11 ,000 chemical compounds. The new spreadsheet type table editor gives more control to the user, the new graphics routines have fewer limitations and more formatting properties. The capability and speed of calculation routines have also been improved.

Jan 1, 1998

By Rolando Campos

In August 1993, the operation of Refimet Chile's copper custom smelter commenced at La Negra, near Antofagasta in northern Chile. Design smelter throughput corresponded to 235 000 tonnes of concentrate, calcines and copper cements arising from suppliers in the north of the country to produce 90 000 t/y of blister copper. Refimet had initially gained experienced in building and operating leaching, roasting and a blast furnace facility at Rungue, near Santiago, followed by Roasting at La Negra. The initial smelter project was based on conventional reverb- smelting and Peirce-Smith converting and the majority of equipment was 'purchased second-hand and rehabilitated or modified. After only 3 years in production, the treatment capacity was significantly improved by introduction of technical improvements to the original plant operating scheme. Recently, the plant was further expanded to an annual smelting capacity in excess of 400 000 t/y feed, corresponding to around 160 000 t/y copper production. This expansion, referred to as Phase 2, was achieved by modification of the reverb to oxy-fuel firing, addition of a further (second-hand) acid plant, fire refining and anode casting facilities. Parallel development of concentrate injection into enlarged converters-also took place. Following successful commissioning of Phase 2 expansion, initial engineering studies for a third expansion phase have been completed. This aims to use leading technology based on bath smelting of bone-dry concentrates in a Continuous Reactor. This paper provides an overview of the relatively short plant history, its development and improvements together with operating indices achieved.

Jan 1, 1998

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993

By Mark Kramer

This paper is limited to treatment of bottom and fly ash waste resulting from WTE and RTE Cogeneration plants, commonly known as trash burners. The body of the paper defines waste generation and conventional treatment schemes. This paper does not identify a best treatment, however, it does offer a general perspective of the treatments to lead the reader to further investigation. Advantages and disadvantages of the ash treatments Is discussed in each treatment section.

Jan 1, 1996

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By Young-Sool Jin, Heung Nam Han, Hong Joon Kim, Jae Kon Lee

A mathematical model was developed considering non-symmetric cooling' and stress distribution in both thickness and width direction of strip on a run-out table of hot strip mill. In order to solve a transient heat transfer equation including the heat evolved from phase transformation, a finite element method coupled with thermodynamic and kinetic analyses was applied. The heat capacity of each phase and heat evolution due to phase transformation were obtained from the thermodynamic analysis of the Fe-C-Mn-Si system based on a sub lattice model. The phase transformation kinetics of the steels was derived by using an inverse additivity technique with continuous cooling experiments. Heat transfer coefficients of strips on the run-out table were, by applying an inverse method, determined from the actual mill data under various cooling conditions. As for the stress analysis, the density change of strip due to cooling and phase transformation, and the transformation superplasticity were considered. A 90nstitutive equation for the transformation superplasticity, which is related to the phase transformation kinetics and the internal stress due to the density change of strip, was applied. A finite element method was adopted to calculate the deformation behaviour of strip on a run-out table of hot strip mill. Using the models, the temperature-phase-deformation history and distribution of a strip on the run-outtable was calculated.

Jan 1, 2001

By Ann M. Hagni

Microscopic and sub-microscopic gold commonly occurs in the sulfides pyrite (FeS2) and arsenopyrite (FeAsS). To recover refractory gold from pyrite and arsenopyrite, these sulfides are roasted to create porosity and permeability prior to cyanide leaching. A new technique of adding Ca(OH)2 and roasting, lime roasting, is being tested fro retention of contaminant sulfur and arsenic and effectiveness of gold extraction. The lime roasting of pyrite at 500°C contains anhydrite (CaS04), oldhamite (CaS), calcium sulfite (CaS03), hematite (FenOs), magnetite (Fe304), and minor amoupts of pyrrhotite (Fel.,S) and pyrite. At 600°C, 650°C and 700°C the main constituents are anhydrite, oldhamite, and hematite. At 750°C, 800°C, and 850°C anhydrite and hematite are the predominant phases with minor oldhamite. The roasted arsenopyrite at 450°C contains arsenic sulfides, calcium sulfite, hematite, and minor oldhamite, magnetite, and pyrrhotite. At 650°C 700°C 750°C and 800°C, anhydrite, oldhamite, arsenic sulfides, and hematite are present. At 850°C, the same minerals are present with only minor oldhamite. The textures indicate excellent porosity and permeability at high temperatures. At lower temperatures, rims of low porosity and permeability surround many of the pyrite and arsenopyrite particles, and the complete oxidation process from pyrite to pyrrhotite to magnetite to hematite can be observed in individual particles. Additional process mineralogy techniques employed in this study are electron spectroscopy for chemical analysis (ESCA) and cathodoluminescence microscopy (CLM) in the determination of the calcium-sulfur- oxygen phases. Automated scanning electron microscopy-energy dispersive spectroscopy was utilized to analyze particles for gold content. Reflected light microscopy (RLM) revealed arsenopyrite and pyrite encapsulated in quartz particles of the gold-bearing concentrate, gold roast calcine, and cyanide leach residue.

Jan 1, 1993

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid aluimina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scanning electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By A. E. Torma

In recent years the copper industry has gained considerable economic stability. An essential part of this industrial wealth is attributable to the successful application of bio-mediated heap and dump leaching techniques in the recovery of copper from low-grade resources. This study evaluated the leachability of a chalcopyrite conlentrate using naturally occurring mixed culture of predominantly Thiobacillusferrooxidans and Thiobacillus thiooxidans. For the effects-of pulp density, the overall reaction rate constant (k) and the order of reaction (n) have been determined to be 1.93 h-1 and 1.36, respectively. Cyclic voltammetric measurements revealed that intermediate reactions are involved in the chalcopyrite oxidation. Using the Price approach, it was shown that the dissolution of chalcopyrite is solid state diffusion controlled.

Jan 1, 1992

By Liyuan Chai, Bing Peng, Ji Peng, Di Yu

"Electric arc furnace (EAF) stainless steel dust has been classified as a hazardous waste by various government regulatory agencies as it releases heavy metals to environment. The solidification of EAF dust is to stabilize the hazardous components to the amorphous silica-alumina-based clays. The process of solidification is investigated and the softening temperatures of dust and additive clay mixtures are measured for economical thermal treatment. The results indicate that the mixture of dust and local clay with the ratio of 1:1 has the lowest softening temperature 1100 °C and it could pass the toxicity characteristics leaching procedure (TCLP) test for the environmental regulatory limits after thermally treated at softening temperature for 15 min. Major phases of thermal solidification product clinker are CaAl2Si2O8, (Fe, Cr)2O3, (Fe, Mg)(Cr, Al)2O4 and Al6Si2O13.IntroductionThe yield of stainless steels in China arrived to 10 million tons in 2006 and more than 0.2 million tons of stainless steel dust are produced annually. Approximately 1-2 wt.% of scrap charged to an electric arc furnace (EAF) enters the off-gases and then is converted into the dust and reported to the bag-house. The disposal or landfill of the dust becomes a serious environmental problem in China due to the increased production of stainless steels in recent years. The dust contains elements such as chromium (Cr), nickel (Ni), lead (Pb), zinc (Zn), cadmium (Cd) and their solubility in leaching media exceeds the environmental regulatory limits [1]. Even though easily feasible for low-grade MgO, it is not appropriate to stabilize the heavy metals from the heavily contaminated soils after the dust landfill [2]. Several dust treatment technologies have been developed and they can be divided into two types. One is to recover the metals from the dust [3, 4] and another is to stabilize hazardous components present in the dust [5, 6]. Recycling of the dust generated in EAF is a remediation option for cleaner production. Direct recycling of EAF stainless steel dust was developed to recover the metal value from the dust and protect the environment [7], but it was only suitable for the dust with high contents of Ni, Cr and Fe. As for the dust with low valuable metal content, thermal solidification is an appropriate choice for the dust treatment."

Jan 1, 2012

By Tim B. Vander Wood

Standard methods of determining clay mineral powder aspect ratios involve manual scanning electron microscopy analyses of shadowed particles in order to measure both platelet thickness and diameter. We present a method whereby the diameters of platelets are quickly determined by automated scanning electron microscopy and their images are recorded and digitally transferred to a transmission electron microscope equipped for parallel electron energy loss spectroscopy. Thickness' of platelets whose diameters are known from the previous analyses are determined by measurement of the ratio of scattered and unscattered electrons in the beam after it has been transmitted through the platelet.

Jan 1, 1995

By Baokuan Li, Fang Wang

"Comparing with the single electrode in electroslag remelting processes, two series-connected electrodes have the advantage of little inductance, lower power consumption and higher melting rate, which was widely used to produce superalloys and specialty steels. Detailed understanding of the electromagnetic field distribution is essential for both improving ingot quality and saving electric energy. In the present work, a 3D finite element model was developed for the magnetic field, electromagnetic force, current density and Joule heating field of electro slag remelting processes (electrode, slag and ingot) with two series-connected electrodes using Maxwell equation, Lorentz law and Joule law. The results show that the maximum current distribute occur at the middle of electrode, due to the interaction of selfinduced and mutual-induced of two series-connected electrode; associated magnetic flux density on the inner side of electrode increase and the outer decrease; The maximum joule heating is at the interface of slag and electrode. The parameter study shows that if the current frequency is greater than 35Hz, the current density in inner electrode tend to linear distribution; with the increasing of original current, The maximum current density near the wall in electrode will increase linearly; with the increasing of electrode innnersion depth and decrease of slag cap thickness and the maximum of the joule heat in slag will increase.IntroductionElectroslag remelting processes(ESR) are widely used to produce superalloys and specialty steels [l-3l_Two pair, four pair or six pair electrodes in electroslag remelting processes is common in casting large scale ingot, which has the advantage of little inductance, lower power consumption and higher melting rate, comparing to singe electrode. They have the same essence with two electrodes in ESR.Compared to the single electrode ofESR, the other electrode is added which can decrease the reactive resistance and power consumption in the two electrodes of ESR. It is a complicated metallurgy process with a series physical and chemistry phenomenon from the molten of steel to the solidification of ingot [4-71_ These physical and chemistry phenomenon originated the effect of alternating current of high intensity. The rule of the alternating current of high intensity which revealed the law of physical and chemistry phenomenon in ESR is the precondition of improving ingot quality and saving electric energy. Jihe Wei and Yongli Ren[S-9lstudied the distribution of electromagnetic field in single electrode ofESR with Maxwell equation and relative electromagnetic theory. It had the limitation that take the electrode and mold as infinite conductivity. A detail analysis of Electromagnetic fields in ESR had been conducted by Patel A D [JO-llJ using general stream-function formulation. It is difficult to extend to three dimensions which could not be used widely. Daniel V [lZJ and Kharicha A [BJ only analysis the current density associated magnetic flux density field and temperature field without the whole irlformation of electromagnetic field. Maopeng Geng [l4J considered the current density and temperature field of the real and fake electrodes in ESR without skin effect. As to the complication of the two electrodes of ESR, it is rarely reported the electromagnetic field and Joule heating field of the two electrodes in ESR. The rule of effect of electromagnetic and modification of numerical simulation should be studied in depth."

Jan 1, 2011

By Z. Smieszek, W. D?browicz, J. Pawlowski, G. Krawiec, J. Czernecki, J. Por?mbski, S. Gizicki

Rapid development of the automotive industry and motorization has been observed in Poland over the last decade. This phenomenon has increased the amount of used car batteries requiring recycling and has thus posed new challenges for their processing. Orzel Bialy" S.A, is the major secondary lead smelter in Poland. Ibis paper describes the program for smelting technology modernisation and productivity increase through the application of oxy-fuel burners, which has been implemented at "Orzel Bialy'' S.A. The main objective of smelter modernisation, which was to increase the furnace productivity by 20%, has been achieved. This paper outlines the previous and present state of the lead acid battery scrap smelting technology at the "Orzel Bialy" S.A. Specifications of the burners and of oxygen installation are given. Industrial tests with the modernised smelting technology and optimisation of the process parameters are described, and the results obtained are discussed.

Jan 1, 2000

By Peter G. Cooper

"During 1987, the feasibility of modernising the ER&S smelter at Port Kembla, NSW, Australia was studied. The selection of appropriate technologies to carry the smelter into the 21st century considered issues such as capital cost, existing infrastructure, feed mix, capacity, product quality, flexibility and potential for further development. Both hydrometallurgical and pyrometallurgical process schemes were considered. Some novel combinations were assessed but ultimately rejected. Final technology selections included proven smelting and anode furnace processes, pyrometallurgical slag cleaning and modifications to existing equipment. This process scheme balanced risk against development potential within the constraints imposed by the existing plant.BackgroundThe Electrolytic Refining and Smelting Company of Australia (ER&S) has operated a custom copper smelter at Port Kembla since 1908. Existing technology includes a sinter plant/blast furnace, three small Peirce Smith converters, two reverberatory anode furnaces and a conventional tankhouse. These process units were all installed prior to 1960 and have proven to be flexible enough to process the wide variety of domestic feed materials purchased by ER&S.However, by the early 1980s, threats to domestic concentrate supplies highlighted the need for major changes to reduce operating costs to world competitive levels. Various studies in the ensuing years failed to identify an economically attractive solution. Furthermore, pressures were increasing to improve the environmental performance of the smelter.During 1986 the options for redevelopment were again considered and by the end of 1987 technologies for the retrofit had been selected and a full feasibility study was completed."

Jan 1, 1988

By Peter K. Everett

One of the major driving forces behind the development of the Intec Copper Process has been the increasingly stringent regulations governing SO2 emissions and, in some parts of the world, a declining H2SO4 market. Other incentives include operating cost (9.2 US c/lb Cu), capital cost (US $1400/annual tonne Cu compared with smelter cost of US$3-4000/annual tonne Cu) and the ability to treat low grade and contaminated concentrates. With such advantageous features, widespread use of the process is expected over time, leading to the production of large amounts of residues containing around 25% elemental sulfur, together with approximately 50-60 % akaganeite (FeOOH) and the ganggue minerals originally present in the concentrate feed. This paper briefly describes the Intec process chemistry involved in the formation of elemental sulfur, thereby avoiding atmospheric sulfur dioxide pollution, and the investigations to be carried out either to extract it or to turn the residue into a valuable by-product while minimising any adverse environmental effects, The process is being developed jointly by a group of fifteen major international mining companies.

Jan 1, 1996