Search Documents

By D. M. Fermino, C. G. Bastos Andrade, M. G. Fernandes, F. R. Valenzuela-Diaz

Treatments with high concentration solution of inorganic acid at temperatures under boiling point are a usual method for clay minerals structure modification. For many industrial uses bentonites must be cleared of impurities. In the present paper, a sample of Brazilian bentonite from Vitoria da Conquista, Bahia was modified by mild acid attack using hydrochloric acid under moderate conditions (90 °C, reaction times of 1, 6, 12, 18 and 24 h in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, acid solution/clay ratio of 1 g/10 mL). The attacked samples were characterized by CEC, XRF, SEM, EDS and Stereomicroscopy. The purpose of these attacks is to reduce the concentration of impurities with minimal damage in clay minerals structure. The modified bentonite presented good results and tends to be a good economic and environmental alternative to manufacturing products with high added value such as polymer/clay nanocomposites, cosmetics and medicines.

Mar 1, 2017

By Afonso Garcez de Azevedo, Anna Carolina Lopes Rabello, Renan Tavares Vicente, Sergio Neves Monteiro, Amanda Maia Ferreira dos Santos

Civil construction is a sector of extreme impact in the Brazilian economy, with construction and demolition waste (RCD) having an extreme impact on the amount of urban solid waste. In this research it was proposed to propose a way of using these residues in the construction of concrete artifacts for structural use. Concrete specimens with sand substitution by RCD were produced in different percentages as a way to contribute to reduce,recycle and reuse thi large amount of waste from the construction industry. The objective of this work was to study the mechanical properties of structural concrete with total and partial replacement (25, 50, 75 and 100%) in sand mass. The results of the compression test indicate good quality for concretes with mass substitution of up to 75% per RCD.

Mar 1, 2018

By Wagner Aldeia, Duclerc Fernandes Parra, Danae Lopes Francisco, Ademar B. Lugão, Lucilene Betega de Paiva

The inorganic nanotube halloysite (HNT) is a promising type of natural occurring filler for polymers. Its characteristics, such as high aspect ratio (10–50), small size, and high strength (elasticmodulus—140GPa) suggest that HNT shave a potential use in high-performance polymer nanocomposites. Compared to other nanoclays and nanosilica the relatively low content of hydroxyl groups on their surfaces makes HNTs relatively hydrophobic, although, sometimes, this is not sufficient for guaranty a good interfacial adhesion in composite systems. Further hydrophobic treatment is required to improve HNTs compatibility with polymer matrixes, maximizing interfacial interactions. In the present study, different percentages of EPB (2,2-(1,2-ethene diyldi-4,1-phenylene) bisbenzoxazole) was used to perform anon-covalent functionalization of halloysite, based on electron transfer interactions. The functionalization is characterized by specific surface area (BET), thermogravimetric analysis (TG) and water/toluene extraction experiment.

Mar 1, 2018

By Xuyang Liu, Xuewei Lv, Yu Zhang, Xiaolong Wu, Chunxin Li

Titanium nitride is a broad-spectrum specific functional material because of its many superior properties. Therefore, it is necessary to investigate synthesis methods of TiN and alloys containing TiN reinforcement. In the current study, with the increase of nitrogen gas pressure and the optimization of routine ball milling parameters, the conventional mechanical ball-milling method can be improved, the nanometers TiH2-TiN composite powder can be synthesized successfully in a shorter time. Nitrogen gas filled in ball mill jar in which the pressure was 0.6 MPa. TiH2 powder was milled under nitrogen atmosphere at a spinning rate of 250 rpm. The results show that the stable TiN is formed after grinding for 2.5 h according to the X-ray diffraction pattern. DSC (differential scanning calorimetry) curves also indicate that milled compound powder adsorbs certain nitrogen gas. The gas adsorbed in TiH2-TiN composite can exist stably below 200 °C.

Mar 1, 2017

By K. Adham, T. Buchholz

Debottlenecking of high temperature processes within an existing metallurgical plant can significantly increase the throughput to meet new production demands. Modeling and simulation can help to fulfil that aim through incremental changes and operational improvements, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. This paper describes a methodology of how modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the minimum cost points for a plant capacity expansion. This technique is presented through a generic description that can be applied to different metallurgical processing studies. We start with heat-and-mass balances, draw a bottleneck diagram, brainstorm capacity increase options, and prepare a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients (Adhametal et al. in A Success Path from Process R&D to Commercial Plants, Montreal, Canada, [1]).

Mar 1, 2017

By Qingyun Huang, Wei Lv, Junyi Xiang, Xuewei Lv, Chenguang Bai

The roasting is the key step for the extraction of vanadium from vanadium slag by calcification roasting–acid leaching process. In this study, thermogravimetric analysis and kinetic study of vanadium slag in the presence of calcium oxide was investigated. The maximum oxidation degree was slightly increased by increasing temperature from 700 to 900 °C then almost unchanged further increasing temperature to 1000 °C. The reaction mechanism was analyzed through both Sharp method and ln-ln method. Results showed that the mechanism the reaction in the a range of 0.1–0.8 corresponded to the random nucleation and subsequent growth, as represented as (G( a)=[ −ln(1−a)] 1/3 = kt. The apparent activation energy was calculated to be 3.5 kJ/mol according to Arrhenius equation.

Mar 1, 2018

By Mingming Zhang, Udaya Bhaskar Kodukula, Marcelo Andrade

The physical and chemical properties of sinter feed are important factors that determine the productivity and quality of sinter product. In this study the feasibility of treating sinter feed by high pressure grinding rolls (HPGR) is investigated for selective cracks generation exploiting weak zones along grain boundaries of poor quality iron ores without generating much fines. The pre-treated sinter feed was characterized for size distribution, surface area, contact angle, and SEM analyses. The characterization results indicated that surface area of the pre-treated sinter feed sample increased about 20%. Pot-grate sintering tests results also indicated improvement on cold permeability, sintering yield and productivity, sinter Tumbler index, and low temperature degradation index (LTD) after HPGR pre-treatment.

Mar 1, 2018

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, Pso, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of 02 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By M. Demuth, B. Holleis, M. Potesser, D. Spoljaric

"In 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today's and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Warme-Institut ""GWI"" in Essen (Germany) and the University of Leoben, different new burners have been developed.The efficiency of industrial combustion processes can be increased in two ways (which can be seen in Figure 1 ), either by preheating the fuel and combustion air or by adding oxygen. Due to the high 79 % Nz ballast in air combustion, only low flame temperatures can be reached. This results in high heat loss in the exhaust gas, caused by the low combustion efficiency. Oxygen can be introduced into the combustion chamber using different techniques:• Oxygen fuel burners• Direct oxygen injection into the fuel air flame• Underlaying of the fuel air flame• Enrichment of the combustion airIn Figure 2, the theoretical flame temperature for the stoichiometrical combustion of natural gas is plotted as a function of oxygen enrichment. Therefore, it can be concluded that even low enrichment values produce higher flame temperatures and result in higher combustion efficiency."

Jan 1, 2012

By Hao Rang

The article Is specially to Introduce the recovery process of Nb, Mn, P from slags and reutilization techniques of the remaining slags. Nb-Mn-Fe alloys which contain 14-16% Nb, 40-60% Mn can be obtained after using fire refining process of " Blast Furnace-Revolving Furnace-Electric Furnace -Electric Furnace, "meanwhile, phosphorous slags which the content of phosphorus pentoxide Is 29.21%. Further going through wet metallurgical processing and electrowinning technics to recover grading 99°o metallic manganese. Finally, phosphorous slags are grinded finely to be as phosporous fertilizers to be directly used for farmlands. Small particle size (0-8mm) rich slags are mixed with slight solid additions for balling directly, and taken Into blast furnace with blocky slags all together. The remaining tall slags are fully used as constructional materials, slags cement as well as a serial of wall materials, road materials, ground ornamental materials without burning operation and steam curing. The compressive strength range of those materials is up to 15-30 MPa. There is no more solid waste slags effluent In the full technical process.

Jan 1, 1994

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By Jiann-Yang Hwang

A study on microwave assisted chalcocite leaching was carried out with a microwave hydrothermal reactor. The leaching was conducted with thick mineral slurries (50-100 g/l). The leaching media is a mixed solution of CuCL2 and NaCL The investigation included the effect of leaching temperature, quantities of the minerals per unit slurry volume as well as the initial concentration of cupric ions were investigated. The results were discussed and compared with that using conventional leaching method.

Jan 1, 2003

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013

By Sergio N. Monteiro

From the leaves of the sisal plant (Agave sisilana) a relatively strong fiber can be extracted and is nowadays being investigated as a possible reinforcement for polymeric matrix composites. For this purpose, it is important to determine the critical length of the fiber with respect to the matrix to be reinforced. This has never been properly done for sisal fibers in polyester matrix. Therefore, this work characterized the critical length of sisal fibers, with different sizes, embedded in polyester capsules by means of pullout tests. The critical length obtained allowed the sisal fiber/polyester matrix interface shear stress to be calculated. The relevance of these values for polyester composites reinforcement with sisal fibers is discussed.

Jan 1, 2009

By Luciano B. Oliveira, Alexandre M. Stumbo, Luis G. C. Marques, Valdo S. Marques, Sergio N. Monteiro

"Similar to the ethanol program, initiated more than 30 years ago, the recently created biodiesel program in Brazil is expected to rely on private initiative based on agribusiness for vegetable oil production. Campos dos Goytacazes is a large county in the northern of the state of Rio de Janeiro with land still available for oily vegetables plantation in addition to the land traditionally occupied by sugar cane plantation, which is used to produce ethanol. In order to extend the biodiesel program to Campos dos Goytacazes, the State University of Northern Rio de Janeiro (UENF) is conducting a technical project for the development of the infrastructure for biodiesel production. In this work, the infrastructure based on versatile equipment for biodiesel esterification built in the Center for Alternative Energy of the UENF is presented.IntroductionBiofuels are gaining worldwide attention as a possible economical solution for the prediction of declining reserves of petroleum and related increase in price of barrel. However, nowadays, a more relevant question is the climate changes caused by burning fossil fuels. This is especially the case of coal and petroleum based fuels, mainly gasoline and diesel that propel the majority of vehicles and generate a large amount of CO2 emissions responsible for global warming. This combination of economical an environmental problems is already providing a strong motivation to substitute conventional fossil fuels by renewable biofuels. More than just the interest of the market financial forces, government legislation is imposing a new order that obliges the use of biofuel. Many countries including the USA, the European Community, Japan and Brazil are committed to gradually substitute biofuels into their fleet of vehicles."

Jan 1, 2008

By James C. Sever

The mode of operation of dolomite kilns at a magnesium reduction plant using the Magnatherm process was designed to minimize operation cost and maximize kiln refractory life. Analysis of downstream operation issues shows the quality metric for dolime changed from loss on ignition to specific surface area. This produced a complete change in kiln operation; the net results being major plant productivity increases decrease in operating cost, and increases in both kiln operating costs and reline frequency.

Jan 1, 2015

By Sergio N. Monteiro

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and,consequently,affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of curaua fiber in epoxy matrix composites. A small critical length was found for the curaua fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2009

By Wang Shuchan, Zhang Zimu, Zhang Dianhua, Liu Yan, Zhang Ting-an, Zhao Qiuyue, Lv Chao

Rare earth extraction tank has many adverse effects like big floor space and high production accumulation during industrial production. Current researches usually focus on changing the device structure without making a breakthrough towards gravity clarification. This paper attempts to achieve this goal by using both the action of clarification by gravity and clarification by stirring. Because many physical parameters affect the clarification and separation rates, the density, viscosity and surface tension of the two phases were determined at different temperatures and different concentration of aqueous solution. The innovation of this research involves adopting the Karl-Fischer method to investigate water content in oil phase during the stirred separation process. In this paper, the separation effect of different physical parameters was studied and the dimensional equation between water content and the physical parameters was established by combining with the experimental data.

Jan 1, 2014