Search Documents

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By C. Strachan

This paper presents an evaluation of tailings dam incidents from the 1994 USCOLD Tailings Dam Committee report. Comparisons are also made with water storage dam incidents from USCOLD reports and recent tailings dam incidents. The evaluation results show that tailings dam incidents are due to a number of factors including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions, and that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated, and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring, and tailings characteristics.

Jan 1, 1999

By E. Martinez

A heavy mineral sand sample was tested containing 13% heavy mineral consisting of rutile, zircon, and ilmenite. Eleven tests were run at a mill site with a Mineral Deposit Limited MG 4 spiral to determine the effect of the addition 0; magnets to the spiral compared to conventional gravity separation. Different magnet configurations and field strengths were tested. Optimum results were obtained with the spiral retrofitted with magnets. The heavy mineral content of the concentrate was increased from 55.5% in the control to 64.2% with the magnets. The 8.7% improvement in heavy mineral recovery was due not only to the weakly-magnetic ilmenite, but also to increased recoveries if the non-magnetic zircon and rutile. The increased recoveries were achieved with no loss of concentrate grade.

Jan 1, 1992

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By J. L. Carr, A. K. Smith, C. C. Jobes, G. T. Homce

"Underground continuous mining machines pose a difficult safety challenge since their operators generally work in close proximity to these machines in very restricted spaces. Intelligent software for use with magnetic proximity detection systems has been shown to accurately locate workers around mining machinery in real time. Calibrating these systems requires the manipulation of a lot of data to determine the calibration constants. Researchers have developed software to analyze, convert, and visualize data acquired during this calibration process to more accurately model magnetic fields and their interaction with the environment. This paper details the background, development, and operation of the resulting application software focusing on the utility of the graphical user interface to visualize the magnetic field calibration data. The refined data developed by this process can then be utilized by the proximity detection system to more accurately identify the location of miners working in an underground mining environment. INTRODUCTION Roughly half of the electricity consumed in the United States is produced with coal, and roughly one-third of all US coal production comes from underground mines [1]. Over the last century underground mining health and safety has seen a continuous and dramatic improvement. However, machine-related injuries and fatalities continue to be a major safety concern [2]. Every year, hundreds of miners are severely injured while operating underground mining equipment, and 39 miners have been killed in striking/pinning accidents involving continuous mining machines (CMMs) since 1984. CMMs, such as the one shown in Figure 1, are large mobile machines that are used to mechanically cut coal in an underground mine. These machines weigh approximately 40 to 50 tons, have hydraulically articulated appendages, and are capable of moving at speeds up to six feet per second [3]. Modern CMMs are remote-controlled, yet the operator and other miners are often in close proximity to the machine. Recent research by the National Institute for Occupational Safety and Health (NIOSH) reveals that the locations workers take relative to the CMM are usually influenced by visibility requirements and safety concerns [4]. The Mine Safety and Health Administration (MSHA) estimates that at least 28 fatalities involving CMMs since October of 1984 may have been prevented with proximity detection technology [5]. MSHA further estimates that proximity detection could prevent 20% of all deaths throughout the industry [6]."

Jan 1, 2016

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By Robert K. Jones

Filter media can be defined as that material which effects the removal of finely divided solids from a fluid. Thus the removal of dust from air or turbidity from water, for example, can be the result of passing the fluid through a properly supported filter media. Since filtration in one form or another has been practiced since pre¬historic times filter media have been made from an extremely wide variety of materials. Vegetable and synthetic fibers (used loose, or formed into papers, felts or cloth) sand, ground coal, diatomite, perlite, wire cloth, porous metal, and bonded aluminum oxide are among the more important materials used today.

Jan 1, 1961

By Andrew T. Zador

The growing demand for energy combined with the need to protect and preserve the environment have become prime considerations in the design of efficient coal handling ports and their associated stockpiles. The transportation system is analogous to a connected chain which originates at the mines and terminates at steel mills or power plants, in which the port and the stockpile reserves are a vital link. Railroad transportation costs can be minimized by rapid discharge of the cars which, in turn, requires that an adequate stockpile system be available. Ocean transport costs can be minimized by having an efficient high capacity ship loading system and sufficient quantities of coal on hand -all of which also requires an efficient stockpile system to meet shipping demands. The connector between the two modes of transportation, therefore, is the port stockyard. It is here at the interface that optimization of land utilization and materials handling equipment results in a total transportation chain that can operate as a smooth efficient system. Multiple origins of coal require the simultaneous handling of large quantities of coal of many grades. Railroad transportation logistics often limit and define the incoming arrival patterns and limited rolling stock often require priority treatment for railroad operations. The physical limitations of prime ocean frontage require that coal stockpiles be built close to residential or industrial areas which entail strict environmental controls. Large capacity, enclosed coal stockpiles for ocean shipping have not yet been considered feasible but may be forthcoming in the near future. Several have been analyzed.

Jan 1, 1978

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit's floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By M. R. Peterson

The U.S. Bureau of Mines has investigated new methods for increasing the selectivity in flotation by creating and regulating reagent concentration gradients within flotation columns at steady-state operation. Gradients were generated and traced in a water-only system with the use of fluorescent dyes, and the effects of various operating parameters on these gradients were investigated. From this investigation, it was found that both gradual and steep gradients could be generated in the froth cleaning zone, and that these gradients could be changed through the manipulation of both physical and chemical operating parameters. The application of reagent-gradient control to mineral systems could improve both flotation grade and recovery in commercial flotation operations without the use of additional flotation circuitry.

Jan 1, 1992

By N. Gritzuk

The area of Canada with which we are here concerned consists of Yukon Territory and Northern British Columbia. Generally it lies west of the coastal mountain range and access to the sea can be gained at only selected points which are relatively few. It is served by the Alaska Highway as well as a provincial and territorial system of roads permitting transport of mining products to Whitehorse in Yukon Territory. This town it the northern terminus of the White Pass and Yukon Route, which system provides a rail service between Whitehorse and Skagway, Alaska a distance of 110 miles, and thence to Vancouver, British Columbia, by the coastal Motor Vessel C. J. Rogers, a distance of an additional 890 miles. At present the service between Vancouver, B.C. and Whitehorse, Y. T. is on a fourteen day basis. The coastal vessel, capable of carrying 3,200 tons of cargo, was specially designed and built in 1955 for handling containerized cargo and general cargo northbound, and containerized and palletized asbestos fibre, and palletized lead and zinc concentrates southbound.

Jan 1, 1961

By W. S. Fyfe

The future environment of our planet, with the concept of sustainable development, has moved to centre stage of all future plans for development. This global view is new. It presents great opportunities and challenges for the Earth Sciences. We have the tools to describe our environment on all scales - planetary to molecular levels. We must respond to this great demand by world society.

Jan 1, 1990

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By George M. Anderson

The extraction of industrial minerals is usually confined to relatively small mining operations. The recent COSMAR (Committee on Surface Mining and Reclamation) report found that 93% of all mines in the United States were of the small unit variety. Also, of the total number of mines in the U.S. (15,279) 96% were in the industrial minerals (non-metals excluding coal) category. To break it down further, 86% were sand and gravel, and crushed stone operations. Therefore, we are talking about a very large number of small mining operations. If these small miners can afford to hire a college graduate, what kind of training should this person have beyond the normal mining engineering curriculum to best serve the problems that he or she will encounter?

Jan 1, 1981

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By R. K. Mehta

Existing acid mine drainage treatment techniques are not remedial In nature, i.e. though heavy metals can be removed from acid mine water, their presence in tailings and large quantities of these tailings tend to increase capital and operating cost for tailing management. This paper presents the results of a series of systematic tests which finally resulted In the development of the "ferrite" process for mine drainage of coal operations at ambient temperature. The role of pH, temperature, quantity of ferrous salt addition and degree of oxidation is investigated targeting the production of high emu spinel ferrites and effluent water complying regulatory standards with respect to Iron. manganese suspended solids and pH.

Jan 1, 1992

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977