Search Documents

By Eric K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. However, previous models have tended toward being either data-intensive and deterministic, or data-limited and highly stochastic. The need for a fully integrated package with a simplified user interface has never been more apparent. In this paper, the design of a surface mining simulation model documented in Albert (1986) is described. The basic features of the surface mining system and their counterparts in the simulation model are discussed. The methods and algorithms used to implement these subsystems are presented. Considerations of information management and software design are illustrated, especially as they apply to the application of the package by a mining engineer. An example is provided to demonstrate the concepts embodied in the model and to show how a surface mine is simulated from mine parameters.

Jan 1, 1989

By V. T. Vacariu, P. D. Georgescu, N. Tomus

To assess the potential for radioactive pollution unique to the environmental conditions of the Bacau phosphogypsum waste dump, surface samples were taken, drillings were performed on the entire waste dump's height, and the Ra226 distribution on the height and surface considered to contain a medium content of the radium of 0.57 Bq/gr was studied. Thus, the waste dump's radioactive potential was estimated at 30-40 Ci in equivalent Ra226. Also analyzed was the granulometric composition of the phosphogypsum and the distribution of Ra226 on granulometric orders, which indicated that the radium was concentrated in the very fine fractions. Parameters were set up for the classification by hydrocycloning to obtain a fine class (less than 41 microns) having a radium content of more than 0.9 Bq/gr and a coarse class having less than 0.37 Bq/gr. A chemical process was devised for removal of the radium from the phosphogypsum with the possibility for recovering the contained sulfur.

Jan 1, 1999

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By R. D. Grove, M. F. Elliott, R. L. Weigel

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators' vision when major deviations occur. An image analysis system has been developed by IMC Agrico Company (IMCA) to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By S. Donges, P. L. Dunstan, B. J. Huls

The commissioning of a distributed digital control system for the grinding circuit at Cuajone was completed by mid-August 1985. Development of a successful strategy, excellent operator acceptability, and the visual aspects offered by the display of the central console improved mill through- put significantly. The inherent features of a digital system enhanced the flexibility in grinding control and allowed the milk and classifiers to be operated at maximum capacity. This paper discusses the strategy development and the production restrictions encountered, and evaluates the overall performance of the digital control system.

Jan 1, 1988

By Wayne Wride, Amy Lamb, Debra Sonntag

In today's "information age", we have the ability to collect volumes of data about a company's performance. The challenge is to turn that data into information employees can understand and use to fine-tune equipment, modify work processes, and ultimately manage production. Software programs have increasingly given end users control over what data is used and how it is presented. Kennecott has implemented an information system capable of collecting and storing data at the primary level. This enables plant personnel to transform historical data into information for action. Kennecott plans to expand its data collection and use trending and reporting capabilities to move toward a fully optimized operation.

Jan 1, 2000

By M. Dondi, M. Surracco, G. Alfano, P. Saba

Recent investigations on fine grinding with jet mill miprototypes of original design, constructed at the DIMM and Centro Studi of the National Research Council at Cagliari University, have led to the realization of a third generation micronizer characterized by large capacity and high efficiency. The new model and its distinctive features are described here and the results are presented of grinding tests on typical, high grade Sardinian minerals used for quality products. The operating principles of the jet mill are described in relation to the mechanico-elastic properties of the minerals treated. In particular the efficacy of the comminution process is demonstrated in terms of both solid treated and of impact, attrition and shearing forces generated in the micronizer. Particle size distribution of the finished products are reported, that satisfy the most stringent market specifications for the different minerals, as well as energy consumptions. The alternative operating options for solving particular grinding problems and minimizing energy consumption are discussed. Lastly, the main developments of the jet mill for a possible application at industrial scale are suggested.

Jan 1, 1995

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By Lucien Duckstein

The purpose of this paper is to give recommendations for utilization of water resources in a mining region, considering also water supply and environment; the case study of mining for coal and bauxite under the karstic aquifer of the Transdanubian mountain of Hungary is used to illustrate the approach, which consists in formulating a static multiobjective control model and solving it by compromise programming. The three activities of regional mineral resource exploitation, water supply and environmental protection are represented by different objectives which cannot be expressed in commensuerable units. Thus, a solution which is optimal for one objective is usually far from being optimal with respect to the other two objectives. As a result, we are not seeking an optimal solution for the conjunctive regional system, but a good compromise, trade-off or "satisfactum" (1), (2).

Jan 1, 1979

By David G. Hammond

INTRODUCTION Previous papers and discussions at this conference have already covered the subjects of identification and nature of risks, allocation of risks and contractual arrangements. In this portion of the conference, in the light of topics already covered, we will consider how to minimize risks and how to mitigate losses. Webster defines mitigate as "to make less severe or painful", an apt definition for our purpose! RISK MANAGEMENT POLICY The first thing that must be said about risks, especially in construction, is that they exist and that they don't necessarily fall alike on the just and the unjust. Some risks, i.e., some kinds of risks, must be recognized as inevitable in engineering and construction and therefore must philosophically and realistically be accepted as part of situations to be dealt with. Dealing with means minimizing, covering, and sharing of risks and doesn't mean merely passing off the risks to someone else. While some risks can be avoided, for example, whether the structure will fall down or the excavation will cave in, risks management primarily deals with: A. minimizing risks---whomever risk it may be B. equitable sharing of those risks among the participants.

Jan 1, 1979

By J-P Franzidis, M. C. Harris

Increasing costs, falling grades and a low gold price have caused severe problems for many of South Africa's gold mines. The need to maximise efficiency is extremely urgent. This paper describes the use of column flotation cell s to scavenge significant quantities of additional gold from flotation plant residues; in particular, very fine particles of free gold not recovered by conventional flotation. Experimental gold- specific collectors enhanced gold recovery significantly. The paper also reports the results of other plant trials, carried out on a variety of ores.

Jan 1, 1991

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By Jerry Grott

Southwest Salt Company is solution mining the Luke Salt Body of probable late Miocene age. The discovery hole, from which the first core was recovered, was drilled in 1968. The deposit was encountered at a depth of 880 feet, and the bit was still in salt at the bottom-hole depth of 4,500 feet. The solar ponds, developed on land formerly dedicated to agriculture, have an annual capacity of about 90,000 tons. Because land values are very high, mining rates and procedures are governed by the need for near-saturated brine to minimize land requirements. Because of the frequency of dust storms, the salt operation uses a unique wet-harvesting method. Most inventory is kept in the ponds under brine and harvested only a few days before shipment. Studies of the nature of crystal growth and the distribution of windblown and brine impurities led to the development of procedures for processing salt of high chemical purity and low insolubles content. Chemical purity exceeds that of most salt produced in fuel-fired evaporators. Salt is shipped from Phoenix as tar east as west Texas and as far west as central California. Occasional shipments have been made to Hawaii and Alaska.

Jan 1, 1987

By C. A. Roberts

What are the benefits and limitations of financial analysis software as a decision making tool in the mining industry? Traditionally, the assumptions and simplifications imposed by complex and uncertain information have been viewed as the main obstacle to reaching an optimum decision. Recently, however, phenomena such as corporate culture and power structure have received increasing attention as significant influences on organizational decision making processes. Studies of these phenomena have suggested an alternative way of understanding decision making processes and an alternative view of the role played by computer analysis in such processes. This paper presents these two views of decision making, and examines what each implies about the role of financial analysis software as a decision making tool in the mining industry.

Jan 1, 1992

By T. J. Harvey, W. van der Merwe, J. Joubert

GeoBiotics, LLC and Kumba Resources (Pty) Ltd are jointly developing the GEOCOAT® heap bioleaching technology and downstream processing technology for recovery of zinc from tailings at the Rosh Pinah Mine in Namibia. This paper outlines the development of a computer simulation for the bioleaching of sphalerite and the downstream processing. Computer modeling has shortened the product development cycle by allowing many flowsheet scenarios to be analyzed negating much of the expensive and time consuming laboratory testing. A model was developed using the Limn® system which is an Excel® Add-In flowsheet drawing and solution engine. Given that most engineers are familiar with Excel® this software is extremely easy to use and has less hidden calculations making model verification much easier.

Jan 1, 2003

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994

By Mark C. Williams, Thomas P. Meloy

Particle shape characterization is a complex task made more difficult because of the human eye's sophisticated recognition of shapes, giving rise to the assumption that shape analysis is considered a simple problem. Further exacerbating the problem is the question of whether particles have a general shape. Old and new shape measuring techniques are discussed, particularly the new image analysis methods techniques such as Fourier, Haar, Walsh and Delta. Problems with the current image analysis equipment and future research equipment needs are presented.

Jan 1, 1989

By B. R. Satio, P. G. West-Sells, D. B. Dreisinger, B. J. Y. Leong, G. A. Kordosky

Electrolytic techniques have historically been used to remove arsenic, antimony and bismuth from copper refining electrolytes. However, both solvent extraction and ion exchange techniques have been heavily researched and in a number of cases commercially introduced. In this study a large number of solvent extraction reagents and ion exchange resins were screened to determine the selectivity of the reagents for impurity removal. Solvating extractants were found to efficiently remove arsenic from electrolyte. The extent of arsenic extraction increased in the following order: TBP < DBBP < DPPP < Cyanex 925 < Cyanex 923. Antimony and bismuth extraction from electrolyte were demonstrated with the reagent 2EHAP04. The ion exchange resins UR-3300 and Duolite C-467 were found to strongly extract antimony and bismuth from electrolyte. C-467 appeared to be superior to UR-3300.

Jan 1, 1993

By J. Hanna, R. Kalathur

Over the years, Alabama&apos;s coal industry has generated, during mining and cleaning operations, about 150 million st of fine waste coal, with this total increasing at a rate of 2 million stpy. Reclamation of the fine-size wastes (containing 20% - 60% clean coal by weight) provides, free of charge, mined and crushed feed stocks for coal recovery. Also, the removal or recovery of pyrite from the tailings should eliminate a major source of acid-water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the +100-mesh material produced commercial-grade coal averaging 7.6% ash, 0.8% sulfur and 13,471 Btu/lb. However, the coal yield, at about 31 % - 56%, was relatively low. Froth flotation, using mechanical and froth column methods, gave similar coal products at much higher coal recovery rates of 87% - 93%. This coal analyzed 10% ash and 1.1% sulfur.

Jan 1, 1993

By B. Govindarajan, T. C. Rao, M. Vanangamudi

The results obtained from hatch, flotation experiments on two coals were used to develop relationships between the recoveries of water and solids into the concentrate. When the recovery of non-ash material (RN) for any size fraction is plotted against a parameter X, defined as [x _ Amount of (W) recovered x Collector dosage (C)in the concentrate (cc)(kg/t)] a single "non-ash recovery curve" is obtained. Non-ash recovery curves thus obtained from different size fractions are used to get a unique "modified non-ash recovery curve" for a given coal, using the reduced efficiency curve concept. Similar observations have been noted in the case of recovery of ash material (RA) also. The amount of water recovered into the concentrate is plotted against a parameter "Water Recovery Factor (WRF)," defined as [WRF = T.F.(1+C)] where T is time (in sec) and F is frother dosage (in kg/t). Plotted in this form a characteristic water recovery curve, for a given coal is obtained that may be defined by the following equation: [W4=W_(1 pWRF-e] The above relationships have been verified against the experimental results obtained from three more coals and are found to give satisfactory predicted values.

Jan 1, 1992