Search Documents

By Thomas R. Kuesel

Just south of the L'Enfant Station in Seventh Street, the WMATA system splits into two branches, each comprising twin single-track soft ground tunnels. Immediately at the beginning of the section, Interstate Route 95 crosses transversely over the alignment in open cut, removing most of the cover over the tunnels. Seventh Street spans I-95 on a bridge whose abutments and pier also cross transversely over the four tunnels, with their footings as little as 7 feet above the tunnel crown (Figure 1). Soil investigations revealed that the tunnels would have to be driven through mixed face, with a clay invert and a waterlogged sand crown. Thus, there was a good chance that the roof would fall in, leaving 1-95 and the Seventh Street Bridge in a crater. Since there was no roof that could be counted on, these were figuratively (and potentially truly) Washington Metro's Topless Tunnels (Figures 2 and 3). DESIGN ALTERNATIVES Faced with this situation, the designers considered several options, including temporary detours that would permit demolition of the bridge and building tunnels under the 1-95 Freeway by cut-and-cover methods. They also investigated structural underpinning of the bridge and freeway pavement, and strengthening the bridge abutments and center pier by post-tensioning to enable them to span over any subsidence trough.

Jan 1, 1976

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By Tina Živec, Žibertm Marko

"Civil design has changed in many ways using BIM (Building Information Modelling) technology in its most recent form. Such a technological breakthrough has not been successful so far in traditional oriented Engineering Geology, except in the Mining and oil exploration markets with budgets on much different scales. The fact is that paper, pencil and hand drawn sketches are still state of the art and a perfectly acceptable way of producing subjective geological interpretations.Using the technology available, we have developed a set of procedures and techniques to combine the latest surveying and remote sensing technology, GIS based tools to manage large data sets and BIM modelling techniques in a 3D geological environment.To demonstrate the concept, the forthcoming Karavanke tunnel project (Slovenia) has been chosen for testing techniques. The project, with its rich documentation from previous phases and new data available, represented a good basis for testing the possibility of digitizing geological data while communicating with Leapfrog Geo 3D modelling algorithms. This type of procedure would then allow engineers at the construction site to use the 3D model for prognosis and evaluation, while upgrading it daily with new information.INTRODUCTIONThe Karavanke tunnel crosses the mountain range on the border between Slovenia and Austria. As the geology is very complex due to its imbricate fan structure, a series of geological – geotechnical and hydrogeological investigations have been performed since the 1970s, resulting in extensive project documentation. The construction of the 7864 m long single-tube two-lane tunnel took place in the late 1980s. Currently, the tunnel represents a critical point on Pan-European Transport Corridor X (Salzburg, Austria – Thessaloniki, Greece), with insufficient safety measures. The need for improved traffic flow and enhanced road safety led the Slovenian government in 2013 to a decision to continue with activities regarding the construction of the second tunnel tube 70 m east of the existing tunnel.The extensive project documentation from previous investigation phases and construction of a new tunnel tube presented a good base for a pilot project, in order to test the emerging new technologies for data acquisition, processing and analysis in a 3D environment. Several products are available on the market for data acquisition and 3D geological modelling, but only a few can be applied in the civil design, as well. Developing a standard format and procedure for implementing the 3D geological model using new remote sensing techniques, 3D geological modelling tools, such as Leapfrog Geo and BIM (Building Information Modelling) modelling techniques would move the Engineering Geology, Geotechnics and Tunneling to a more advanced level. 3D modelling tools would therefore not only be used as a visualization tool, but would also contribute to in a more efficient communication and workflow between the professionals involved in the project."

Jan 1, 2016

By J. A. Mielczarski

An infrared external reflection spectroscopy (ERS) technique has been developed to study the structure of the adsorbed layer of ethyl xanthate formed on copper and natural chalcocite (Cu2S) electrodes. The infrared technique provides information concerning the identity and the orientation of the adsorbed species at monolayer and submonolayer coverages. X-ray photoelectron spectroscopy (XPS) studies have also been conducted to monitor changes at the surface. The results show that the first oxidation peak on the voltammograms for copper and the first and second oxidation peaks on the voltammograms for chalcocite electrodes are not characteristic of a chemisorbed xanthate species, which is contrary to what has been reported by other investigators previously. As evidenced by the XPS spectra, there was an increase in sulfur relative to copper on the copper and chalcocite surfaces over the potential region where these oxidation processes occur. The spectroscopic results (ERS, XPS) indicate that the second and third (on copper) and the third and fourth (on chalcocite) oxidation processes recorded on the voltammograms are due to cuprous ethyl xanthate adsorption. The orientation of the adsorbed molecules of xanthate was observed to change with increasing surface coverage. Therefore, it has been concluded that xanthate can modify the copper and chalcocite surface in two different ways. At lower potentials, xanthate is a source of sulfur for the formation of a sulfur-rich surface. At higher potentials, an adsorption layer of cuprous ethyl xanthate is formed. Contact angle measurements show that both of these processes of xanthate surface modification lead to an increase in the hydrophobicity of the substrates.

Jan 1, 1990

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By Jim V. Rouse

Adverse water-quality impacts of uranium mining and milling activities on both surface- and ground-water resources in the Grants Mineral Belt have recently been documented.1 In some cases, the impacts resulted in violation of existing regulations and license conditions and have endangered public health. Unfortunately, industry-sponsored ground-water monitoring programs do not adequately record the actual impacts of mining and milling on ground-water quality.

Jan 1, 1976

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By J. Y. Lee, J. Kang

"A selective chlorination process using cuprous chloride (CuCl) was investigated for producing high-grade chalcocite (Cu2S) from chalcopyrite (CuFeS2) feed. The chalcopyrite feed was reacted with CuCl in the presence or absence of sulfur (S) at temperatures between 900 and 1,100 K for five hours under an argon gas atmosphere. The experimental results indicate that iron (Fe) was selectively removed from the chalcopyrite feed as ferrous chloride (FeCl2) at 1,100K and the mass percentage of Fe thus decreased from 31.5 percent in the feed to less than 0.05 percent in the residue, under certain conditions. As a result, high-grade Cu2S was obtained from chalcopyrite in a single step. This new selective chlorination of chalcopyrite using CuCl as a chlorinating agent is therefore feasible for producing high-grade Cu2S.IntroductionCurrently, blister copper (Cu) is commercially produced from sulfide ores by pyrometallurgical methods. These methods entail matte smelting and converting, with the removal of iron (Fe) and sulfur (S) as slag — mainly Fe2SiO4 — and sulfur dioxide (SO2) gas, respectively.In the pyrometallurgical method, as shown in Fig. 1 (Schlesinger et al., 2011), Fe is removed through two steps at high temperatures of around 1,500 K to reduce the loss of Cu during slag formation. However, the slag still contains 1 to 8 percent Cu. Therefore, Cu in the slag is recovered by slag treatment processes, after which the concentration of Cu in the slag decreases to around 0.4 to 1.3 percent. Although Cu is recovered, the slag that had undergone the treatment processes is difficult to use as a feedstock for ironmaking owing to the small amount of Cu remaining in the slag (Schlesinger et al., 2011).In addition, large amounts of SO2 gas are generated by the oxidation of S in the current Cu production process. The SO2 gas generated is captured and used to produce sulfuric acid (H2SO4). However, despite the development of SO2 gas-capture technologies, the emission of SO2 gas is still a problem in terms of environmental considerations.Several studies had been carried out in the past to overcome the drawbacks of the current process. The extraction of Cu from sulfide ores using a chlorination process is one alternative that had been investigated by several researchers. Most chlorination processes used chlorine gas (Cl2) as a chlorinating agent at temperatures between 573 and 1,023 K under an inert atmosphere (Donaldson and Kershner, 1962; Olsen et al., 1973; Kumar, Li and Warren, 1985, 1987; Kanari et al., 1999; Kanari, Gaballah and Allain, 2001)."

Jan 1, 2017

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950's a number of anionic iron procedures were evaluated and in the late 1950's and early 1960's the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis', Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960's The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

Stillwater Mining Company has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The first use of a TBM was a 4 m (13 ft) diameter main beam unit at the Stillwater mine starting in 1988, where 6.4 km (4 mi) of tunnels were driven parallel to the J-M Reef orebody on four different levels. TBM?s were central to the development of the East Boulder Mine as two 4.6 m (15 ft) TBM?s drove two 5,639 m (18,500 ft) parallel tunnels to access the J-M Reef; one of these units is still in service driving a 2,591 m (8,500 ft) access West of the East Boulder mine for the Graham Creek project. For the Blitz Project, a 5.5 m (18 ft) diameter main beam unit will be utilized to drive a 6,858 m (22,500 ft) ventilation and rail haulage level East of the Stillwater mine. TBM?s have been preferred method for developing new mines and sections of the J-M reef as the geometry and geology of the Stillwater Complex allow for faster development compared to conventional methods.

Jan 1, 2012

By Charles E. Mongan

The problem of roof control in the coal-mining industry is of major importance inasmuch as 65 percent of all coal-mine fatalities result from falls of roof, face, or ribs. The Health and Safety Research and Testing Center of the Federal Bureau of Mines at Pittsburgh, Pa., is engaged in several programs directed toward increasing safety in coal mining. The Roof Control Research Group has 4 programs aimed at reducing roof fall accidents. One of these programs is the use of sonic techniques to explore mine roof strata.

Jan 1, 1961

By J. O. Down

St. Marys Cement Company operates two cement plants in Southern Ontario, Canada. The original plant, located at St. Marys, a town 20 miles north of London, Ontario, began operations in 1912. A second plant, located at Bowmanville, Ontario, 40 miles north east of Toronto, began operations in 1967. In June 1973, St. Marys Cement began feasibility studies of modernizing their wet process plant at St. Marys. Over its 61 year life, this plant had been expanded from 335 m. tons per day (375 s. tons per day) to 2000 tpd (2200 s. tons per day), with all the original equipment retired several years ago. The objectives of the feasibility study were to develop a conceptual plan for a dry process plant and to de-, fine the appropriate process method and equipment. This study proceded along four fundamental fronts: a) How could the clay raw material, a glacial till with up to 20% boulder content, be processed in dry form and beneficiated? b) Were the raw materials suitable for the most efficient form of dry process kiln, the 4-stage preheater? If a 4-stage preheater kiln is selected should it utilize a precalciner? c) What type of clinker cooler should be used? d) What environmental constraints would be imposed on this plant and how can they be reconciled with capital and operating limitations? During the feasibility stage, pilot plant work was done on two possible solutions to the clay problem, operating plants in Europe were visited and discussions held with kiln and mill vendors.

Jan 1, 1977

By Adrian J. Mathias

For many years excavations were made in rock exclusively by conventional blasting methods, and without concern for damage to the rock surfaces which remained after the excavation was completed. Recently, however, there is an increasing awareness for the importance of making rock excavations with as little damage as possible to the remaining rock surfaces; consequently, several revolutionary new precision blasting techniques have been developed during the past few years. These techniques, variously known as cushion, smooth- wall, perimeter, pre-shear, and pre-split blasting, basically involve the creation of a fracture plane in the rock between a series of blasted holes. The variations in each of these techniques are largely due to the differences in hole diameters, hole spacings, methods of charging, and sequence of blasting used to achieve certain specific results. The development of these precision blasting techniques was initiated by Canadian Industries Limited in 1953 at the time the Sir Adam Beck No. 2 Hydro-electric Project was under construction by the Hydro-Electric Power Commission of Ontario. Since then, these techniques have been somewhat advanced, and they have been applied with varying degrees of success to a number of projects. These projects include railroad and high- way cuts, dam spillway channel excavations, canal excavations, tunnel driving, shaft sinking, and other underground applications.

Jan 1, 1965

By E. R. Drevdahl

It has been suggested that we at the University of Arizona present a paper covering the origin, philosophy, and results of the College of Mines program in the field of computers and operations research. I have worked with the program since its beginning, and I will try to outline the developments as they have taken place. The formal development of the educational and research program in the field of Operations Research and Computer Applications at the College of Mines, University of Arizona, began in early 1957. During the year, the University offered its first formal instruction in computer programming. This was my first introduction to computers, and it did not take long to realize that this new tool had a potential that could be profitably utilized by the mining industry. In March 6f 1957, the University Computing Center began operations with its IBM 650 computer. This machine was the only computer of this size in the local area at this time, The first programming effort was in machine language and the programming cost could only be justified for repetitive-type of problems. The progress in the computer field moved very rapidly and with the development of the many compiler and assembly programs and the addition of sub routines to the computer library, the scope of problems that could profitably be investigated by computers expanded rapidly.

Jan 1, 1963

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol's cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol's estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995