Search Documents

"The adsorption of mixed cationic/anionic surfactants with different molar ratios onto quartz was investigated. The cationic surfactant used was dodecylamine bromide (DDA), and the anionic surfactant was sodium oleate (NaOL). The critical micelle concentration values for the individual surfactants and their corresponding mixtures were determined using a platinum plate. The adsorption mechanisms of mixed surfactants on quartz were studied using contact angle measurements, flotation tests and adsorption amount measurements. At alkaline condition, NaOL depresses DDA flotation of quartz without depressing the adsorption of DDA. The molar ratio of mixed surfactants is found to be a key factor in the orientation of alkyl chains and thereby the flotation response of quartz. A mixture of 1/2 or 1/3 DDA/NaOL forms on the surface of quartz when the concentration of NaOL is higher than that of DDA. The adsorption of the mixture decreases the wetting of quartz since the alkyl chains are in chaotically orientation with a conceivable number of head groups directing towards the solution phase. These results provide important insights into the adsorption of mixed surfactants onto quartz surface. INTRODUCTION Froth flotation is known as an effective method of separating mineral particles on the basis of their surface chemistry, specifically their hydrophobicity. [1]. The hydrophobic particles will attach to the bubbles and rise to the top of the containing vessel to form a froth that flows over the lip of the vessel. The hydrophilic particles remain in the liquid [2]. In the process, surfactant is often used as collectors for surface modification in order to change the wetting properties of mineral particles. The primary long chain alkyl ammonium salts are the most widely used as collectors for the flotation of oxide minerals, such as quartz, muscovite, hematite, phosphate and feldspar [3, 4]. Adsorption mechanism of alkyl ammonium salts on oxide minerals has been extensively analyzed [5, 6]. Generally, the ammonium salts are adsorbed through electrostatic interaction of the polar group of the molecules with the surface of these minerals [7]. Despite many obvious advantages of the ammonium salts in low temperature resistance and hard water resisting, however, their unavoidable drawbacks, such as high sensitivity and poor selectivity for slimes, relatively high cost, have limited their applications [8]. In recent years, mixed surfactants have drawn much attention due to their superior physicochemical and surface properties than single surfactants [1, 9-11]. They have been used in many industrial processes such as dispersion/flocculation, flotation, detergent, corrosion inhibition, cosmetics, foods, paints, chemical mechanical polishing, enhanced oil recovery, and nanolithography [12]. Most of the mixed surfactants have synergistic advantage in reduction of the surface tension and critical micelle concentration (CMC); therefore, they exhibit spurious properties, like excellent surface/interfacial activities, and are less expensive than single mixed surfactant systems [13, 14]."

Jan 1, 2016

By Huijun Shao, Qiang Liu, Zhengming Yi

The increase of the proportion of high Al2O3 content iron ore fine in iron and steel enterprises has brought about a series of problems such as the increase of the viscosity of blast furnace slag and the difficulty of the separation of slag and iron. In order to solve this problem, the effect of increasing MgO content on the technical and economic index, the cold strength, and metallurgical properties of high basicity and high-alumina sinter was studied through sinter pot test. Nova400NanoSEM field emission scanning electron microscope was used to analyze sinter microstructure. The experimental results show that when the MgO content fraction in the sinter with high basicity and high aluminum increases from 1.72 to 2.49%, the vertical sintering speed decreases by 4.38mm/min, the utilization coefficient decreases by 0.51t/(m2 h), and the low-temperature reduction degradation index increases by 6.7%. When MgO content in sinter is 2.11%, drum index and reducibility index are the highest, reaching 61.93% and 86.39% respectively. Mg2+ is mainly solid dissolved in the magnetite lattice and replaces Fe2+, up to 3.64%. The generated magnesie-containing magnetite inhibits the phase transition from Fe3O4 to Fe2O3 oxidation process in the sinter cooling process, which reduces the generation of secondary hematite and is conducive to improving the low-temperature reduction degradation performance of sinter.

Jul 4, 2021

By Malcolm D. Flavel

Recent research into the mechanisms of crushing processes has led to the establishment of new criteria for the effective design and operation of comminution plants. This paper reviews this work and gives examples of the productivity gains and cost benefits that have been achieved in the practical application of these findings.

Jan 1, 1988

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

The 2014 George A. Fox Conference at the Graduate Center, City University of New York in New York City was presented under the theme, ?21st Century Challenges for the Tunneling Industry. Bruce Grewcock, chief executive officer and president of Peter Kiewit Sons? Inc., opened the conference with a keynote address in which he set the tone for the rest of the day by touching on the many challenges the industry is facing, which are plentiful and complex. Covering the breadth of the industry, he spoke about everything from the technical challenges that come from working beneath the streets of some of the most densely populated regions in the world to the challenges that come from working with the people who live in those areas. ?My observation is that we, as an industry, are being asked to put structures in places where they are needed, but are complex environments to work in,? said Grewcock. ?We work in an industry that relies on some of the most technically challenging engineering in the world, and when we are done with a project, we cover it up and no one ever sees it.? Despite these issues, Grewcock said that, in his opinion, the biggest challenge the industry is facing is that of people; more precisely, where to find the next batch of people. Looking out at the conference-record crowd of more than 400 registered attendees, Grewcock quipped that he saw plenty of gray beards and asked aloud, ?Where will we find, educate and train the people to tackle the issues that this industry will face in the future??

Mar 1, 2014

By A. Guzman

The design and construction of a new 140-ton-per-day R. O. M. phosphate rock scrubbing and washing plant was undertaken by Western Knapp Engineering Company, a Division of Arthur G. McKee and Company, for the J. R. Simplot Company, Minerals and Chemical Division, Pocatello, Idaho. The new plant replaces the owner's existing facilities at Conda, Idaho, seven miles northeast of Soda Springs in the southeast corner of Idaho. Replacement of the existing facilities became necessary because of loss in production and recovery. These losses were due in part to varying grades of raw ore from the mine and to the type of process equipment used in the old plant to upgrade the ore. Increase In production and grade was further necessary by demands created by expansion of facilities in Pocatello, Idaho, where all process ore from this plant is shipped. The new process scheme includes an ore-feeding system, scrubbing, screening, classification, wet cycloning, attritioning, filtering, drying, storage and shipping facilities. Space was also left for future increases of scrubbing and classification capacity and for heavy media separation. It is the purpose of this paper to take up some of the considerations necessary in the design of small mills in order to achieve the desired objectives of a successful plant, such as production, minimum operating cost and maintenance cost.

Jan 1, 1969

By Trevor Riters

Advancements in Emerson’s instrumentation technology have brought value and efficiencies to the mining industry. Some think of instrumentation as basic sensors and valves, but with our solutions, we equip operators with real time, accurate, and reliable data that they can use to operate more effectively. Working with Caltrol, an Emerson Impact Partner, we successfully engineered wireless skids for a leach pad to provide precise measurement and control of raffinate solution to many of the large mine sites in Arizona.

Feb 1, 2025

By Leandro Seixas Bicalho, Wagner Cláudio da Silva, Kelly Laranjeira Nunes, Lívia Marques Faustino

Seeking to implement the Global Industry Standard on Tailings Management to improve the safety of their tailings facilities across the globe, mining companies are motivated to invest in new technologies to recover valuable minerals from tailings. One solution being evaluated is the use of magnetic separators to concentrate ultrafine tailings. However, this approach is energy intensive as it requires high magnetic fields to recover ultrafines, and usually results in low mass yields. Additives that modify pulp rheology and surface properties, or selective flocculate ultrafine particles, were tested to enhance the performance of magnetic separation. Promising results in laboratory scale testing different types of additives confirmed that it is possible to increase the mass yield, keeping the selectivity of this stage.

Feb 1, 2024

By E. Bloomstein

The Lone Tree gold mine is located about 4S kilometers east from Winnemucca on the west flank of Lone Tree Hill in Humboldt County, Nevada. The deposit occurs at the north end of the low, rolling Havallah Hills and is about 1 kilometer south of Interstate Highway 80, in sections 11 and 14, Township 34 North, Range 42 East, Mount Diablo Base and Meridian (Fig. 1). The Lone Tree deposit is outside of any previously established mining district and all lands are owned or controlled by Santa Fe Pacific Gold or affiliated companies.

Jan 1, 1993

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By F. J. Susko

The Bureau of Mines applied a flotation model to the hydrodynamics of the Bureau-developed rapid flotation system. Rapid flotation is a process which separates the bubble-particle attachment and froth-pulp separation stages of the flotation sequence into two discrete unit operations allowing the operations to be individually optimized. Both an air-injected hydrocyclone and an in-line mixer were used as the bubble-particle attachment unit and a shallow-depth froth separator was used to separate the ore-laden froth from the pulp. A 10-L/min batch system was tested on a coarse coal feed sample. The system was tested using two different bubble-particle attachment units at various aeration levels in order to test the flotation model. The results of the flotation model reflect general trends observed in the experimental data.

Jan 1, 1993

By N. Arbiter

If two fluid phases are brought into contact with a solid, one fluid may completely wet the surface to the exclusion of the other, or both may wet it, forming a three-phase line of contact. These relative wetting tendencies are quantified by the contact angle 0 which is related by Young's equation (1,2) [12 cos? = 13 ? 23] [to the three interfacial tensions (3). No contact angle for the first fluid, indicating that it does not wet the solid in the presence of the second, means that the difference between the two solid-fluid fluid surface tensions, - 8 is greater than (or just 13 -23 equal to) the fluid-fluid tension 12; a finite angle indicates that the difference is less.*]

Jan 1, 1964

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By Alexander N. Winchell

The cities of St. Paul and Minneapolis are located side by side on a double loop in the Mississippi River near the eastern boundary of Minnesota. Both cities lie on both sides 'of the Mississippi River, which in this region describes an S-shaped curve. The two cities together have a population of over 600,000 people, gathered in an area which has grown to be a single urban district inasmuch as the two cities have expanded until they occupy all the territory formerly between them, though the business centers are ten miles apart. St. Paul is located at the head of navigation on the Mississippi River and Minneapolis, farther upstream, at the Falls of St. Anthony. A recent water¬power development below the Falls of St. Anthony, constructed by the Federal Government, has at the same time made possible navigation to the foot of St. Anthony Falls through a lock around the dam which replaces the former rapids. Minneapolis, in 1920, had a population of 380,000 people, and St. Paul, 235,000. The two cities occupy land at an elevation of 700 to 900 feet above sea level. The average elevation is slightly less at St. Paul. Minneapolis has nearly 4,000 acres of parks and park¬ways, while St. Paul has nearly 2,000.

Jan 1, 1920

By Kef ton H. Teague

This paper will discuss bentonite deposits in Texas, Oklahoma, Louisiana, Mississippi and Alabama. The discussion will be re¬stricted to a review of the so-called calcium or non-swelling bentonites. In other words the exchangeable cation is calcium. The term "bentonite" is used to describe a clay material, composed essentially of the clay mineral montmorillonite. In addition, bentonites may contain various impurities such as glass shards, feldspar, quartz, muscovite and biotite mica, glauconite, pyrite, hydrated iron oxide, gypsum, organic material, etc, Most of the southern calcium bentonites contain at least 70% montmorillonite, Bentonite as mined may range in color from dark grayish greens through various shades of grays, reds, yellows and browns to nearly white. It is normally massive and breaks with a conchoidal fracture. When air dried, closely spaced shrinkage fractures occur. Moist bentonite has a soapy feel, with little or no obvious "grit". Bentonite deposits were first discovered in Mississippi about 1925, in southern Monroe County. During the thirties and early 1940's, deposits were identified in Alabama, Texas, Oklahoma, and Louisiana. Perhaps the earliest production of southern bentonite was from a deposit in the valley of the Tombigdee River, south of Jackson, Alabama in 1936. Production commenced in Mississippi during the latter part of 1938 at Pontotoc. The growth and development of the bentonite industry in the southern United States owes its beginning to three events. The first of these was the discovery by German researchers,

Jan 1, 1972

By J. W. Powell

Several years prior to 1962, it became obvious that in order to develop ore reserves below the Storke Level, it would be necessary to devise a method to facilitate the ore being lifted three hundred feet to the surface or six hundred feet to the mill. The final plans called for an underground crusher complex with two stages of crushing and a conveyor belt gallery for transport of the ore six hundred feet above, to the third crushing stage. Access into the area was gained in 1962, by sinking Five Shaft approximately one quarter mile southwest of the proposed complex site, and drifting into the area. Collar elevation of Five Shaft is three hundred feet above the 600 Level Crusher Complex. All muck was loaded into ten-ton granby cars, hoisted to the surface and dumped. (See Figure 1 for the relationship between Five Shaft and the Crusher Area) Drifting into the Crusher Area contunued until 1965 at which time the Crusher Room Cutout was started. The Crusher Access Drift (CAD on Figure 2) war driven and mining pm- ceeded according to the description on drawings marked Figure 3a and 3b. After the arch portion of the Cutout was excavated and concreted, removal of the center "pillar" commenced. This muck was removed with an Eimco 123C crawler-mounted front-end loader. (See Figure 4) A total of 576,000 cubic feet of rock was removed from the Crusher Cutout. All sup- port was afforded by grouted roofbolts on a specified pattern, as shown in Figure 3c. Crane support columns were put into place and held by braces welded to roofbolt heads. Sidewalls and endwalls were formed and concreted. (See Figure 5 for the finished product)

Jan 1, 1970

By Russell L. Dahl

In a continuing effort to improve plant efficiency, United States Steel's Atlantic City Ore Operations completed the rubber lining of its balling drums in late 1982. This resulted in benefits of reduced bentonite consumption, reduced maintenance costs, improved production rates, and lower power consumption. These advantages far outweigh the disadvantages of increased oversize production and increased surging on the roll screen sizing devices. Certain operating characteristics and variables are discussed herein.

Jan 1, 1983

By Juan C. Diaz, Juan P. Carmona, Manuel Z. Salgado, Oscar J. Restrepo

The “Teaching Kids” project is an educational initiative for young people and children from elementary schools. It is carried out by Mining, Geological, and Environmental Engineering students from the SME Student Chapter of the Universidad Nacional de Colombia, Medellin. The primary purpose of the Teaching Kids project is to share knowledge about geosciences and mineral resources in a didactic and attractive way, emphasizing the importance of identifying the use of minerals in daily life and responsible and sustainable mining in our society. Furthermore, this project aims to promote the importance of pursuing geoscience majors in the new generations and improve the mining industry’s public perception. Different methodologies related to early childhood education are implemented, such as gamification, in which the dynamics of games are adapted during the development of workshops to teach and learn in an active and motivated environment. Furthermore, the Montessori Method is used. It implements textbooks, sensory mineral boxes, and presentations to allow learning through experimentation itself (Montessori 2003). The implementation of this methodology has been successful; it has shown high engagement, participation, and retention of the basic concept of geoscience and mining.

Feb 1, 2025

By Richard M. Winar

In September of 1988, the United States Environmental Protection Agency (US EPA) published final regulations that effect owners and operators of underground storage tanks (USTs). These regulation include stringent technical requirements for owners and operators of USTs containing petroleum and certain hazardous substances. The technical requirements effect both new (those installed after December 1988) and existing USTs and include notification; performance and operating standards; release detection, reporting, investigation; release response and corrective action; and closure requirements for out-of-service USTs. The USEPA also published final regulations regarding financial responsibility requirements for owners or operators of petroleum USTs in October of 1988. These regulations require owners or operators of petroleum USTs to demonstrate financial responsibility for the costs of corrective action and compensating third parties for bodily injury or property damage caused by releases from petroleum USTs. Like thousands of other industries, the mining industry must become thoroughly familiar with these new regulations in order to properly manage their UST systems, ensure compliance, and understand other ramifications imposed by these regulations.

Jan 1, 1990

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971