Search Documents

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By Rusty Winn

"R.E. Janes Gravel Co. is an aggregates producer is located along a paleo-channel of the Ogallala formation (locally known as the Slaton Channel) approximately 48.3 km (30 miles) southeast of Lubbock, TX. In an attempt to beneficiate the 25.4-mm (1-in.) concrete aggregate product, a log washer was installed in the processing line to liberate and remove fines (clay) from the finished product. The introduction of this extra cleaning step increased fines in the finished product, exacerbating the original problem. Several other processing options were investigated before a geological analysis was undertaken to try and define the lithology of the formation and formation characteristics in an attempt to alleviate this problem.Initial assessmentsThe mined resources are mid-Miocene to early Pliocene (16-4 mya) in age and is the eastern exposure of the Ogallala formation of the Southern High Plains escarpment. The Ogallala formation consists of coarse-grained alluvial sediments in paleovalley channel ways from the Rocky Mountains with fine Aeolian and paleosol deposition on the uplands across the High Plains region of the United States. Locally, these Rocky Mountain sediments from New Mexico were transported and deposited in a paleochannel that is approximately 0.805 km (0.5 miles) wide and 15.25 to 18.3 m (50 to 60 ft) in depth. As this channel cut across the Southern High Plains it eroded local rock sources of Late Cretaceous limestones and Triassic sandstones and mudstones incorporating them into the younger Ogallala depositional sequence.Depositional historyThe channel currently being mined is a nontypical Ogallala deposit. The Ogallala in the panhandle of Texas is divided into two units, the Couch and the Bridwell. The Couch is the older of the two and exhibits alluvial sedimentation of thicker and larger gravel (up to 76.2 mm or 3 in.) deposits fining upward to Aeolian sedimentation and thick friable caliche deposits. The Bridwell overlies the Couch and is characterized by alluvial sedimentation, a distinctive red tint and smaller gravel components (typically no larger than 25.4 mm or 1 in.) fining upward to Aeolian sedimentation and thick, well-indurated caliche cap. The Slaton Channel divides these two units and shares lithologic components of both, yet is lithologically distinct due to its Cretaceous Age limestone gravels that can be < 3.66 m (12 ft) in size. Caliche/calcrete is a calcareous (CaCO3) deposit that forms in the B horizon of soils as a rain water leachate of CaCO3 from the upper A horizon."

Jan 1, 2014

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

By Steve Karl, Rock Jenkins

The mining industry appears to be slowly rebounding. But many individuals and company officials are still smarting from the beating they received during the recent recession. As a result, companies have taken the "lean and mean" approach. As pointed out at the Oct. 24-26, 1984 SME-AIME Fall Meeting in Denver, CO, companies are placing more emphasis on optimizing their operations through more efficient mining and processing technologies and equipment. Empathizing with the mining industry&apos;s woes was the meeting&apos;s welcoming luncheon speaker, John D. Withrow, Jr., executive vice president product development for Chrysler Corp. Withrow paralleled Chrysler&apos;s problems of a few years ago with the current problems facing the US mining industry. He said Chrysler&apos;s come-back centered around its engineering and technical personnel, who regained "their seat at the head table." "In short," Withrow said, "we had lost the competitive edge. By cutting costs and people and improving our products we got everybody to believe we could." The 2700 participants at the Fall Meeting attended technical sessions geared toward turning mining back into a productive and profitable industry. Sessions and symposia included papers on precious metals extraction, crushing and grinding innovations, geomechanics, environmental control, health and safety, and various commodities. This article briefly highlights some of the papers presented. To order preprints of these technical papers, see ME, December 1984, pages 1620 and 1621. Computers Gain Mining Acceptance High tech has reached mining. As evidenced by many papers, computers have become valuable tools in many applications. These include tailings ponds operation and waste management; truck dispatching; mine design, simulation, and scheduling; monitoring; and reclamation. Mine planning is generally labor intensive and requires a considerable amount of the planner&apos;s time. P. K. Chatterjee, X. Chung, and Y. Jianjy described a computer-generated interactive graphics approach to under-ground coal mine planning that lessens the manhours involved in producing plans. The computer program examined exploratory borehole information. This included coal seam thickness, tonnage, quality constraints, and the nature of their distribution. Layout designs were then initiated and a probabilistic simulation performed to determine production levels of different extraction strategies. The interactive graphics approach gives planners the ability to quickly evaluate several layout alternatives and select the best one. For surface coal mines, M. A. White, of Arch Minerals Corp., explained several computer programs that aided in his company&apos;s surface mine plans. Several drill hole database and modeling pack¬ages are available. But Arch tech¬nicians developed specific pro¬grams for model strip areas. They were used to form long-term pro¬jections for various area and semi¬area stripping operations. They also generated reports on yard¬age, tonnage, quality, and ratio in¬formation. The information is used in budgeting, to compare mine plans, and to analyze acqui¬sition candidates. While computer-based truck dispatching systems have been used in mining for some time, earlier systems were run on ex¬pensive mainframe or high per¬formance minicomputers. As such, computer-based truck dis¬patching systems have been too expensive for all but the largest mines. Recently, however, a microcomputer-based system, af¬fordable to smaller mine opera¬tors, has become technologically feasible. Y. C. Kim and W. E. Kolb re¬ported on a simulated microcom¬puter system that uses strategi¬cally placed signposts in the pit area to automatically detect truck movements. A microprocessor in the signpost sends information to the microcomputer. The computer determines the truck&apos;s assign¬ment and alerts the dispatcher. He radios the driver his assign¬ment. In addition to the technical pa¬pers, an introductory short course on microcomputers was offered at the meeting. L. M. Kass and J. P. Stone, from the US Bureau of Mines, walked participants through the uses of microcom-

Jan 1, 1985

By D. R. Nagaraj

Editor&apos;s note: Minerals concentration is a disparate area, one involving many disciplines. Flotation, flocculation, reagents, microbial processes, gravity and magnetic separation, and the areas of coal and oil shale - concentration is relevant to all of these. In his article, Nagaraj reviews the latest developments and findings in concentration that have ocurred during the past year. Flotation The Monograph Series "Development in Mineral Processing," (Elsevier, 1985) was devoted to "Flotation of Sulfide Minerals." This volume has 26 articles covering the aspects of flotation chemistry, process development, plant design and equipment, and modeling and process control. The numerous articles on sulfide flotation had one recurring theme - the role of electrochemical processes and redox potentials in flotation and depression. Significant advances have been made in this area. A differential desorption-reflotation process was developed for the beneficiation of calcitic phosphate pebble (Hsieh and Lehr, Industrial Engineering and Chemistry, 1985). The carbonate and phosphate minerals were first separated from silica using fatty acid and the modifiers diphosphonic acid and HF. The collector on phosphate was then desorbed using sulfuric acid, and calcite was selectively floated without additional collector. A two-stage conditioning - initially at pH 10, followed by that at pH < 4.5 - with sodium oleate was developed to improve the separation between apatite and dolomite (Moudgil and Chanchani, Minerals and Metallurgical Processing, MMP, 1985). Separation of Mussorie rock phosphate in India from gangue calcite, dolomite, silicates, pyrite, and carbonaceous impurities was achieved with a three-stage flotation only on -75 µm (-200 mesh) fraction (Vaman Rao et al., International Journal of Mineral Processing, IJMP, 1985). The separation of fine SiC whiskers from other products of coked rice hulls by immiscible liquid and froth flotation was achieved using M1BC, pine oil, and mineral spirits (Parekh and Goldberger, MMP, 1985). Flotation was more economical. The carrier flotation separation of hematite fines from quartz fines was effected using coarse hematite as a carrier and oleic acid and ferric chloride (Cristoveanu and Meech, CIM Bulletin, 1985). Potash recovery from brines by laboratory-pan solar evaporation and amine flotation was discussed by Foot and Juiatt (Salts and Brines &apos;85, Proceedings, 1985). Flotation in a 45-kg/h (99-lb per hour) unit recovered more than 95% of the potash in schoenite and sylvite concentrates containing 28% and 62% K2O, respectively. The effects of fresh concrete into cement and aggregate by a single-step flotation process in aqueous suspension was described (Naegle, Chemical Engineering Science, 1985). The physico-chemical principles for the selective separation of proteins from mixtures using flotation were discussed by Ostermaier and Dobias (Colloids & Surfactants, 1985). Selective flocculation of hematite from silica was studied by Bagster and Mcllvenny (IJMP, 1985). Selective flocculation was more favorable with more highly charged anionic polyacrylamides and with high molecular weight. The cationic and non-ionic polymers flocculated both minerals. In minerals mixtures, there appeared to be very little selectivity unless a combination of dispersant and electrolyte was used. The effect of dissolved minerals species, such as Cu, Fe, and Ni on flocculation of chalcopyrite, pentlandite, millerite, pyrrhotite, and covellite was studied by Acar and Somasundaran (SME-AIME, 1985). Reagents There were some major advances made in reagent development for the minerals processing industry. Cyanamid introduced several classes of collectors, one of which - the diaryl monothiophosphates as acid circuit col¬lectors of sulfides and oxidesulfide ores - was commercialized in 1985. The monothiophosphates are more stable and powerful collectors than the xanthates and dithiophosphates. Hydrolyzed dithiophosphate containing 80% monothio and 20% dithiophosphate was found to give optimum recovery of copper from crude cementation precipitate and separation of Cu and Ni sulfides from matte (Akimova et al., Obogashch, Tonkov, Rud, OTR, 1985). A new class of O-alkyl-Nallyl

Jan 9, 1986

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection&apos;units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer&apos;s preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By Jason Clarke, Glen Trainor

As the mining industry faces increased challenges with declining ore grades and harder to access deposits, operating mine sites in an environmentally responsible and economically viable manner will require innovations that improve efficiency in energy logistics, and automation. Technological advancements in mining have been successful primarily because of the willingness and capability of these solutions to share information with one another, for example OEM payload systems sending information to Fleet Management Systems, and in turn Fleet Management Systems interfacing to ERP systems. To promote and facilitate the sharing of data, there has been a push towards open standards with initiatives led by organizations like ISO, ISA, EMESRT, and GMG. These efforts are aimed at creating a more collaborative and interoperable environment within the sector. However, when it comes to implementing autonomous solutions, a different trend dominates— closed-stack solutions. These closed stack solutions not only prohibit a mine site from selecting best-of-breed solutions, by blocking the competition from entering the market, they also risk slowing innovation that could help overcome the challenges the mining industry faces. Open Autonomy, an internationally published standard that allows any FMS to work with any Autonomous solution, breaks this closed-stack approach and invites competition from other industries. This competition comprises of autonomous suppliers from other industries and manufacturers of smaller, civil-sized haul trucks. The availability and capabilities of these smaller-sized autonomous haul trucks will help tackle the challenges of responsibly and economically mining lower quality ore grades and mining harder to access deposits.

Feb 1, 2024

By L. Yuan, J. H. Rowland

"In 1995 and 2003, the U.S. Mine Safety and Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) that were being used in underground coal mines in the United States. The survey reports gave data for the different AMS manufacturers, the different types of equipment monitored, and the different types of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along belt haulage entries. As of Dec. 31, 2009, point-type heat sensors are prohibited for use for an early fire detection system. Instead, carbon monoxide (CO) sensors are now required. This report presents results from a new survey and examines how the regulation changes have had an impact on the use of CO sensors in underground coal mines in the United States. The locations and parameters monitored by AMS and CO systems are also discussed.IntroductionThe last survey conducted by the U.S. Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems used in underground coal mines in the United States was in 2003 (Francart, 2005). A total of 146 active mines were surveyed. The survey report states that since 1995 there had been a steady increase in the use of atmospheric monitoring systems in underground coal mines as the technology of carbon monoxide (CO) sensors was improved by manufacturers. Atmospheric monitoring systems had become more reliable, and some CO sensors could be purchased with the capability to discriminate between the CO produced by a fire versus CO produced by diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed miners to take the necessary action to put out the fire or exit the mine.At the time of the last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than when using point-type heat sensors (Conti and Litton, 1995)."

Jan 2, 2018

By Bernd Hagenah, Petr Pospisil, Colin Santangelo

This paper explores the profound implications of high-speed train operation on tunnel planning, specifically investigating ongoing high-speed rail projects in California and Texas. The paper delves into the crucial considerations for designing high-speed rail tunnels, including selecting tunnel sections based on aerodynamic factors, which impacttraction power requirements and pressure comfort. The paper also examines the need for emergency stations, maintenance access, and comprehensive safety and rescue concepts to address train incidents. Drawing from international high-speed rail projects, it shares valuable experiences and lessons learned to promote efficient and secure tunnel designs for high-speed train operations.

Jun 23, 2024

By Elnaz Saminfar, Jae Bateman, Eric Westergren, Mark Trim

This paper presents a case study of two major Australian infrastructure projects that used digital engineering to facilitate design delivery: WestConnex Project (Rozelle Interchange), and Sydney Metro West (Eastern Tunnelling Package). The paper presents project overviews and building information modeling (BIM) execution and focuses on modeling techniques, software utilization, data management strategies and how the digital models helped the design-build team mitigate impacts to schedule by identifying clashes between disciplines before the execution of work. Finally, it demonstrates the positive and transformative impact of digital engineering on the design and construction of large underground infrastructure projects and highlights its role in asset management throughout the project lifecycle.

Jun 23, 2024

By Ed Schodowski

Wireless technology is a hot topic for anyone involved in the design, operation, maintenance or upgrading of mines or mineral processing plants because wireless technologies overcome barriers that have prevented many useful data inputs. Wireless communications can contribute to worker safety, satisfy environmental concerns, support plant security, track human and physical assets, and improve equipment maintenance. The cost structure of wireless is compelling and users can realize savings ? up to 90 percent less installed cost than wired instruments ? since wireless technology eliminates the need for expenses associated with cabling, engineering, construction and documentation. Many applications previously considered too expensive have become economically feasible with wireless. Two examples are continuous monitoring of safety showers to notify operators when one has been activated, and monitoring effluents to ensure environmental regulations are being met. In many cases, wireless transmitters can be installed where wired devices were too expensive to justify, or were not feasible due to physical or technical barriers. Examples include monitoring temperature measurements inside a rotating reactor or monitoring process variables in a tough, corrosive environment too challenging for a wired solution. Wireless also gives operating personnel mobility with the ability to communicate from remote or hard-to-reach zones. According to a recent Venture Development Corp. survey covering radio frequency (RF) of microwave industrial monitoring and control products, these features are contributing to the expected nationwide growth rate for industrial wireless applications of 19 percent annually from 2007 to 2012 (Taylor, 2008). At the same time, mineral producers have many questions about wireless systems including their applicability, reliability and security in this industry. Just what can wireless do? Is it secure and reliable? Can these instruments stand up to the rigors of the industry? Can wire-less technology provide the flexibility needed for mining applications?

Jan 1, 2009

By Georgene Renner, Chee Theng, William Gleason

"A walk through the exhibit hall or a glance at the technical programing that was offered at the 2019 SME Annual Conference & Expo and CMA 121st National Western Mining Conference in Denver, CO, Feb. 24-27 makes it evident that the mining industry is an innovative one that is on the cutting edge of technology. However, a glance at the nearly 6,700 attendees of the conference and it is also evident that while the industry is moving forward at a rapid pace in some areas, it is lagging behind in terms of diversity, both in gender and ethnicity.At Monday morning’s keynote session, Hannah Ubi, a millennial and a public speaker who joked that she is the proud owner of a sixth-place swimming trophy and a number of participation medals, addressed a full house that consisted of many men with gray hair or balding heads. The issue of an aging workforce that is rapidly being depleted by retirements is not a new one for the mining industry. In fact, it has been a concern for the industry for more than a decade. The central question has long been, “when the current senior-level people begin to retire, how do we replace them, and how do we fill the knowledge gap that is walking off into the sunset?” SME has been on the front lines in searching for solutions to the impending problem and, along with industry partners, has worked hard to develop programs that will address these issues. Among other efforts, the Society has developed a Ph.D. fellowship program to encourage people to remain in academia to teach the next generation and to help train the next generation to take over in the private sector.“The SME Foundation’s Ph.D. and Career Development Grant program is exceeding expectations at this point with two Ph.D. students graduating and taking a position in academia and two professors achieving tenure,” SME Executive Director Dave Kanagy said during the conference.The Society’s Minerals Education Coalition (MEC) has done its part to help educate future generations about the mining industry with initiatives like EngineerGirl, the Boy Scout Merit Badge and Move Mining, the Shark-Tank-style competition that was held on Monday with five finalists competing for the top prize (ME, April 2019, page 53)."

May 1, 2019

By Shinichi Konda, Gary Nishimura

"Thousands of years ago large glaciers carved much of the landscape in Puget Sound, depositing abrasive and granular soils including cobbles and boulders along with layers of clay and sand. Tunneling in this geology – common throughout much of the northern and Midwestern U.S. – is challenging and can be unpredictable. The use of pressurized face tunneling, most commonly with EPBs and slurry type machines, has made excavation in this geology more efficient, but difficulties still remain. Through analysis of recent projects in Seattle, Washington, USA, the authors draw conclusions as to the best TBM designs and operational parameters for this variable, abrasive and often difficult ground. Performance data is analyzed with an eye towards advancements that could further improve TBM tunneling in glacially deposited soils. INTRODUCTION Over the past several ice ages, extensive glaciers reaching across much of North America transported large amounts of soil and rock as they moved across the land. The substantial weight of the ice sheets mixed together a wide range of soil types along with a variety of rocks and boulders of all sizes. Many rock formations were reduced to pebbles or particles containing highly abrasive characteristics. Any boulders able to survive were generally comprised of harder materials which were scattered throughout the soil. This highly variable mixture of abrasive soils and high strength boulders can be found in many areas across the Puget Sound and other regions of the country. Wherever they are encountered, they often create a difficult and unpredictable mining environment for both equipment design and operation. Modern TBMs are optimized early in the design process for specific types of geology, and unexpected conditions can require extensive modifications. In addition, several operational parameters need to be adjusted to balance ground characteristics, and advance rates can be significantly affected in mixed and rapidly changing soil conditions. Both EPB and slurry machines can be used successfully in these conditions, provided their respective operating criteria are met. Ideally, an EPB is operated with a relatively thick muck consistency, which accommodates moderate changes in soil permeability and maintains a reliable pressure differential through the screw conveyor. However, this also causes higher wear on rotating components and requires more energy at the cutterhead. Alternatively, slurry machines typically operate best with a more fluid muck consistency that can be easily pumped through the extensive piping system. This tends to reduce the wear on the cutterhead and the power requirements of the cutterhead drive system, but also makes the machine more sensitive to changing soil conditions. Generally, the slurry piping system is also more capable of controlling high face pressures, although the screw conveyor of an EPB can also be designed to accommodate most high-pressure conditions."

Jan 1, 2016

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Most, if not all longwall gobs contain explosive gas zones (EGZs), i.e., zones of explosive methane-air mixtures that can cause – and have caused – mine fires and explosions. If the coal is prone to spontaneous combustion, oxygen penetration into the gob must be avoided. This paper summarizes the significant research findings from five years of computational fluid dynamics (CFD) modeling research conducted at the Colorado School of Mines (CSM) under funding from the National Institute for Occupational Safety and Health (NIOSH). CSM Researchers have developed CFD modeling techniques to identify where and under what circumstances EGZs can form in longwall gobs and how EGZ formation and oxygen penetration depend on the ventilation method, face and bleeder ventilation parameters, injection of inert gases and the operation of gob ventilation boreholes. Recognizing these explosion and fire hazards is an important first step in improving the safety of longwall coal mines. CSM modeling research has shown that EGZ formation can be effectively controlled by adjusting ventilation parameters, choosing the proper ventilation pattern and injecting inert gases where necessary. INTRODUCTION In a project sponsored by the NIOSH Office of Mine Safety and Health Research, researchers at the Colorado School of Mines have examined gas compositions and flows in longwall gobs in order to assess explosion and fire hazards. Since gob areas are inaccessible, researchers developed a series of computational fluid dynamics (CFD) numerical modeling tools to characterize these hazards. A variety of CFD models were developed to cover progressively sealed as well as bleeder ventilated gobs for both coal and trona mines. The explosion and fire hazards posed by EGZs in longwall gobs can be summarized as follows.• If the EGZ lies closely behind the longwall face, flames and pressures from an explosion can penetrate the shield supports and reach the active face area, creating blast trauma, burn hazards and toxic, unbreathable atmospheres. • EGZs can be pushed around inside the gob by roof collapses and cave-ins. If they get pushed out into the face area, sudden methane inundations and explosion hazards in face areas can result. • Fresh air flowing into the gob can create an explosion hazard as the gas composition in the gob moves from fuel-rich inert to explosive, creating EGZs. • Ignition sources inside the gob can be frictional ignitions or spontaneous combustion. • Bleeder ventilated gobs are surrounded on all sides by an EGZ that forms along the fringe areas between the fresh-air ventilated bleeder entries and the methane-rich interior of the gob. It is suspected that diffusion flames can propagate rapidly along these EGZ fringes if an ignition occurs"

Jan 1, 2015

By Leo Gentile, David Selhorst

The $528 million Toledo Waterways Initiative (TWI) was implemented by the City of Toledo in 2002 and completed in August 2020. Toledo is one of many US cities required to implement a Long-Term Control Plan (LTCP) but one of few to have completed its plan. TWI consists of three storage and conveyance tunnels, four below grade storage basins ranging from 4 to 36 million gallons (MG), miles of sewer separation and interceptor improvements, green infrastructure and other appurtenant structures to dramatically reduce combined sewer overflows to the Maumee River, Ottawa River and Swan Creek. All three rivers flow into Lake Erie. The City’s 180-year history as a Midwest shipping, manufacturing and transportation hub provided design engineers and contractors no shortage of unknown underground challenges to complete the projects. The City will begin its 5-year Post-Construction Compliance Monitoring in 2021 to satisfy the final LTCP requirement. A program overview and experience from tunnel and underground basin construction in urban areas with buried active and legacy infrastructure will be discussed.

Jun 13, 2021

In this paper, we present design and implementation details of a fuzzy-behavior-based controller for an automated excavator. This robotic excavator must be equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered from bucket mounted force sensors during the excavation process. Implementation details and experimental results using the fuzzy behavior based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining excavator controller.

Jan 1, 1996

By John O. Marsden

"This article is an attempt to capture a presentation given at the 2016 SME Mineral & Metallurgical Processing Division (MPD) Luncheon held on Feb. 24, 2016, in Phoenix, AZ. It was presented as a tongue-in-cheek, lighthearted view of several of the issues facing our industry, while identifying some of the challenges and opportunities available to new engineers entering the industry today.Disclaimer• What you are about to read includes personal preferences, biases and occasionally arbitrary opinions.• Some readers may have dissimilar opinions on the contents and/or the rank order of the lists.There are eight top ten lists offered in this article: (1) Industry realities (2) Things a metallurgical or mineral process engineering graduate should do (3) Books every metallurgist should have on their shelf (4) Things I wish I had known (5) Legends of metallurgy (posthumous, with highlights) (6) Things we’ve forgotten (7) Mineral processing innovations of the past 20 years and, finally, (8) The future? For some items, additional context or clarification is provided after the item, while for other items no further explanation is warranted and none is offered. Top 10 industry realities1. Metal price cycles.2. Bigger is better (except when it isn’t).3. Ore grades declining across the board of metals/commodities.4. Ores becoming more complex.5. Three-fold increase in capital costs between 2004 and 2015.6. Three-fold increase in operating costs between 2004 and 2015.7. Less capital availability/challenging financial markets.8. Environmental constraints increasing.9. Socio-political constraints increasing.10. The mine manager is always impossible to work with.As Table 1 shows, there was more than a three-fold increase in gold operating costs between 2004 and 2014. The increases for copper, iron ore and other commodities were similar."

Aug 1, 2016

By Claudia Castillo, Katja Freitag, Jan Cilliers, Diana Drinkwater, Robert Seitz

The talent gap in mining is not a new challenge. Mining companies continue to seek innovative ways to attract, develop and retain talent, and younger workers are looking for opportunities to develop their professional careers. Training provides a key value proposition for both employees and employers as it helps build a talent pipeline while offering opportunities for learning and growth and value creation. In 2020, Metcelerate launched its 20-month program for early career mineral processing engineers. The program helps develop critical technical skills in the workplace and is a tool to identify motivated engineers and change culture within teams. Learners cap their skills development by executing a technical investigation. This generates immediate value—a win-win outcome for learner and company.

Feb 1, 2025

By John N. Murphy

The past five years have seen communications techniques and hardware developed by the Bureau of Mines and its contractors increasingly brought into use in U.S. mines. The Bureau of Mines philosophy has been to help develop and introduce new hardware that goes as far as possible toward meeting the mining industry&apos;s needs. The Bureau of Nines programs are also designed to provide continuous fallout of new communications capabilities which are introduced to the mine operators as they occur. As more progress is made in meeting mine comnications needs, it is hoped that the mining industry will readily adopt the equipment and techniques that it finds most useful in meeting its individual needs. This paper reports on recent advances achieved in the development of improved nine communications systems.

Jan 1, 1976