Search Documents

By Devan Naik, Matthew Stokes, Andy Nigro

This paper describes the surgical removal of a 24 ft dia. Slurry Shield TBM entombed beneath one of the country’s busiest commuter rail interlockings, the Harold Interlocking in Queens, NY, and the construction of the interface to a cut/cover tunnel which extended the mined tunnel section. A sophisticated SOE was built around the TBM to support active track loads within 8ft. of the excavation. Once the TBM head and guts were removed, a full round CIP lining was installed connecting the existing precast tunnel liner to the C/C tunnel under construction. All this construction was done on a narrow island of land without road access nestled between 7 mainline LIRR/Amtrak rail lines.

Jun 13, 2021

By Thomas Schwind, Elmar Feigl, Gerald Skalla, Angelos Gakis

Cedarvale station was constructed as part of the Eglinton Crosstown Light Rail Line, under the operational Yonge-University Line Subway box of Toronto Transit Commission (TTC). The station was constructed as an open-cut, which necessitated the underpinning of the existing TTC box to minimize the impact on the Subway and allow its unhindered operation. Six mined galleries, 4 m wide by 2.75 m high, were excavated sequentially (SEM) immediately under the existing box, to provide the required space for the installation of the main underpinning beams. This novel solution was executed successfully providing quick access for the main excavation works to commence.

Dec 1, 2022

By Y. T. M. Ocsa, V. O. Tenorio

This research is the result of a geotechnical study carried out in a natural slope in an Open Pit mine in Southern Peru, highlighting earthquakes as an important cause of instability within the case study presented. This leads to analyze the stability of a slope, according to the safety factor and thus consider a future construction in its environment according to the identified requirements. There are known disasters at national and international level that involve human lives because of the lack of analysis of slope stability conditions, which based on the results will allow to control and to take adequate corrective measures. These mass movements are classified whether they are soils or rocks, considering the mechanism and type of rupture, as well as the presence of water, the speed and magnitude of the movement. The movement problems are due to factors of inherent nature and constitute a reason to perform a calculation study to analyze and estimate the safety factor of each of the evaluated cases

Mar 2, 2022

By Mauricio Brücher, Juan Camus

This article deals with open pit mine planning and a computer technology known as Direct Block Scheduling, or “DBS”. This is an emerging technology for modeling mine exploitation strategies using mixed-integer linear programming. This technique has proved to yield stronger economic results compared to the Lerchs-Grossmann (“LG”) algorithm currently used at the beginning of the mine planning process. The article briefly describes the shortcomings of current practice; then, this delves into the superior results obtained by DBS technology compared to current practice. Finally, the article argues that results achieve so far by DBS could be enhanced even further. To do this, the framework to apply this emerging technology, which is also used in current practice, should be modified to better exploit the capabilities of DBS technology. To better understand this change, an illustrated case study is presented at the end of the article.

Jun 25, 2023

By Jesse H. Auvil

In January of 1966, during the annual session of Georgia's General Assembly, Representative Paul E. Nessmith of Statesboro, Georgia, walked into my office and asked me what I thought of the advisability and feasibility of a law which would require the mining operators to reclaim their mined out lands. My answer to him was, as a one time mine superintendent and operator, that I probably would not think very highly of the added cost which reclamation would impose on the operation; but that since assuming the job of Chief Geologist and Assistant Director of the Georgia Department of Mines, Mining and Geology, and in retrospect, I could recommend it very highly, particularly in view of the increased pressure being applied by the Federal government along these lines. I stated then and still emphatically state that this sort of administration should be done on the State level rather than the Federal level. He asked me if I would conduct him on a tour through some of the mining country in which I had worked and to this I readily agreed. The result of this trip was that he was adversely impressed by the devastation which the mining operations had wreaked on that area of middle Georgia along the fall line known as the kaolin belt. Very little except talk was done for the remainder of 1966.

Jan 1, 1970

By Beth Robinson

Central Mexico's mining districts, opened centuries ago during the Spanish conquest, still form the backbone of metal mining in the country today. Beginning at Chihuahua City, the Second Mexican Mining Rail Excursion traveled southeast from camp to camp through this major mining area to Taxco. Improved exploration, exploitation, and beneficiation methods have permitted continuous mining of many old deposits, and led to the discovery of new ones. Minerals not sought by early miners-lead, zinc, copper, and fluorite-now contribute substantially to mining activity in central Mexico. Of Mexico's five physiographic provinces, the rail excursion passed through two: the Mesa Central, and the Sierra Madre Occidental. The Mesa Central province is a wide tableland with basin and range topography, containing important base metal deposits. Mining in this region is primarily of limestone replacement ore bodies. Massive deposits form horizontal mantos or vertical chimneys. In northern Zacatecas, the Santa Eulalia and Naica mines demonstrated this character. The Sierra Madre Occidental lies west of Mesa Central in northern states, then widens to almost the entire width of the country from outside Mexico City to the southern border. The area consists of volcanic beds, several kilometers thick. These intermediate volcanics are primarily andesitic, of Tertiary age. Resting on older strata of adjoining physiographic divisions, the volcanic beds are overlain by a thick series of acidic flows and tuffs. Economic mineralization in the Sierra Madre Occidental is vein-type, primarily gold and silver. Mines at Fresnillo, Guanajuato, Pachuca, and Taxco contribute to the claim that this region is the center for precious metals in Mexico. A third type of mineralization, contact metamorphic deposits, is commercial at Santa Eulalia. First Stop, Santa Eulalia Mine tours began with the Santa Eulalia unit, located 25 km east of Chihuahua City. Mining in the region dates back to the early 1700s. The oxidation zone was worked until 1790, but mining declined until Asarco arrived in the early 1900s, building a selective flotation plant for treating primary sulfides. Asarco still owns 34% of Industrial Minera Mexico, S.A. (IMMSA), operator of the Santa Eulalia mine. Santa Eulalia currently has a milling capacity of 850 t/d. The San Antonio and Buena Tierra mines provide feedstock. Head grades at San Antonio, the mine participants toured, average 80-120 g/t of silver, 1.5-4.5% lead, 4-16% zinc, and 0.1-2.5% copper. Tin and vanadium were also recovered between 1930 and 1940. Estimated proven and probable reserves total about 7.6 Mt, although 1.8 Mt of reserves are located in areas of high water pressure and volume, which makes extraction difficult. Water is a significant production problem at the San Antonio mine. In one area, an AX drill hole encountered 2.6 m3/min (700 gal/min) at a pressure of 2.5 kPa. Precautions are taken to cope with the problem: protective drilling in advance of blasting is performed;

Jan 2, 1982

By Z. D. Hora, W. N. Hamilton

Introduction Some unique opportunities exist for industrial minerals in British Columbia and Alberta. The region's diversified geology, particularly in British Columbia, offers favorable environments for a rich variety of mineral resources. Many minerals have been produced for years. For some, however, the level of production is far less than the potential. Others have had production in the past, but are not currently produced. Still others are known to exist and may have been actively prospected. But they are not yet developed. In addition, a number of speculative possibilities have recently come to light. The potential significance is not fully confirmed, but is suggested in showings in favorable geologic settings. Location and geography British Columbia and Alberta are the westernmost provinces in Canada (Fig. 1). The region overlaps two major physiographic divisions of the country, the Cordillera and the Interior Plains. It also takes in a small segment of the Canadian Shield on the east. The entire territory is greater than 1.6 Mkm2 (618,000 sq miles). Most of British Columbia lies within the Cordillera, a mountainous belt some 800 km (500 miles) wide. The belt is made up of three main physiographic components, the Eastern, Interior, and Western subdivisions. The Eastern subdivision embraces the rugged, linear ranges of the Rocky Mountains, elevations between 2600 and 3300 m (8530 and 10,800 ft). They form a 100-km (62-mile) wide band straddling the BC-Alberta border and extending northwest across northern British Columbia. The Interior subdivision includes several ancient mountain ranges but is dominated by an intermountane plateau area of low relief (average elevation 1200 m or 3900 ft). The Western subdivision is dominated by the Coast Mountains (elevations between 1800 and 4000 m or 5900 and 13,123 ft). These form a band about 175 km (110 miles) wide into which are sculptured the spectacular fiords of the BC coastline. Alberta lies largely within the Interior Plains, a prairie region of low to moderate relief (elevations between 200 and 1200 m or 650 and 3940 ft) formed of nearly horizontal bedrock strata. The Plains surface rises gradually to the southwest toward the deformed belt of the Rocky Mountains, where the bedrock strata are upturned, folded, and faulted. To the east, the Plains merge with the Canadian Shield, which exposes the Precambrian crystalline basement of western Canada. The total population of the BC-Alberta region is about five million people. Minerals, forestry, and agriculture are the primary industries here. It has well developed infrastructures to service these industries. British Columbia is third among the Canadian provinces in metal mining - $1.1 billion in 1985 - and first in forest products. It is also second in hydro-electric power development. Alberta leads all provinces in total mineral production, largely due to its extensively developed petroleum and natural gas resources - $26.2 billion in 1985.

Jan 12, 1987

By Christine M. Kammer

In 1852, six barrels of iron ore were loaded aboard the steamer Baltimore at Marquette, MI, after a trip by mule wagon from the nearby Cleveland Iron Mining Co. Shipped to Sault Ste. Marie, they were portaged around rapids and reloaded onto another ship for the final journey to the steel mills of Cleveland. In 1855, the same company-the predecessor of Cleveland-Cliffs Iron Co.-chartered the brigantine Columbia to carry the first iron-ore cargo through the newly opened Soo locks. In 1981, about 2,190 iron-ore shipments in the form of taconite pellets were transported by water from US Great Lakes-ports. The total volume during the 284-day shipping season was 63 Mt (62 million It). Counting Canadian ship¬ments, almost 76 Mt (75 million It) of iron ore were moved on the lakes last year. The five Great Lakes-Superior, Huron, Michigan, Erie, and Ontario-contain 20% of the world's fresh water. The area surrounding the lakes has 26% of the nation's populations, 47% of its steel production, and over 80% of the raw materials required to make steel. That figure includes 71% of the country's iron ore and 40% of its limestone. Only the availability of low-cost water transportation of raw materials has kept the heartland steel producers competitive. Iron ore shipped on the lakes originates in the Lake Superior district's Mesabi and Marquette iron ranges. Major mines and their principal partners are Cleveland-Cliffs Iron Co.'s Empire, Republic, and Tilden; Armco and Republic's Reserve Mining Co.; Oglebay Norton Co.'s Eveleth; Hanna Mining Co.'s National and Butler; Inland Steel Co.'s Minorca; Pickands Mather & Co.'s Erie and Hibbing, the latter operated in conjunction with Bethlehem Steel Corp.; and US Steel Corp.'s Minntac. Pelletized ore products at these facilities is shipped through seven principal ports on the upper lakes: Duluth, Two Harbors, Silver Bay, and Taconite Harbor, MN; Superior, WI, and Marquette, MI, on Lake Superior; and Escanaba, MI, on Lake Michigan. In 1981, tonnage volumes ranged from 13.3 Mt (13.1 million It) shipped from Duluth, to Marquette's total of 5.4 Mt (5.3 million It). The ore docks, with two exceptions, are operated by railroads, most of which are owned by mining companies. Table 1 illustrates US iron-ore shipments in 1981. In the lower lakes, ore is discharged at dock facilities close to the great steel-producing centers of Chicago, Detroit, Cleveland, Pittsburgh, and Buffalo. Between the mines and mills, lakes and connecting waterways form one of the country's most effective transportation systems. Each year, vessels on the Great Lakes transport about 181 Mt (200 million st) of bulk industrial and agricultural materials-a greater quantity at a lower cost than can be achieved by any other transportation mode. Major commodities in Great Lakes trade are iron ore, coal, grain, limestone, cement, sand, and petroleum products. About 125 US flag vessels serve this trade, among them 13 "1,000-

Jan 10, 1982

By Paul M. Jr. Musgrove, Thomas D. Henderson, Mark B. Nesbitt

Introduction History. Vat leaching operations began in October 1953. Since that time, about 4.2 million tpy of oxide ore averaging 0.72% copper have been treated. Economic conditions, improved operating methods, and increased production facilities have allowed the ore grade to be reduced over the years. The average ore grade was 0.84% Cu during the 1950s, 0.68% in the 1960s, and was 0.50%, or below, during the 1970s. By 1961 some 35 million tons of oxide ore had been removed from the mine, exposing the underlying sulfide ore body. A 5,000¬ tpd concentrator was constructed and put into operation to treat the sulfide ore in November 1961.1 The original crushing plants were used for both oxide and sulfide ores, but by adding a third crushing shift, six days per week, the total ore treated was raised from 12,000¬17,000 tpd. Dwindling oxide ore reserves prompted expansion of the concen¬trator to 13,500 tpd in 19672 so that exhaustion of known reserves of both ores would occur at nearly the same time. Again, no additional crushing facilities were added during the expansion. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to about 9,000 tpd. Instead, the addition of two crushing shifts per week and improved operating procedures have increased the treatment rate to 26,500 tpd-13,000 tpd to the leaching plant and 13,500 tpd of sulfide ore treated in the concentrator. Geology. The Yerington ore body is a disseminated porphyry copper deposit where a quartz monzonite porphyry intrusive contains the major part of the ore values, with some copper mineralization found in the adjacent granodiorite and other rocks. The geology of the Yerington Mine was aptly described by J. R. Wilson (Mining Congress Journal, June 1963). The ore body is one of few porphyries where geologic conditions were optimum for the formation of an important concentration of oxidized ore with minimum economic effect of secondary enrichment. The principal mineral in the oxidized zone is chrysocolla, which irreg¬ularly occurs dispersed throughout the rock and as narrow seams along fissures. The grade of the ore in the oxidized zone is generally the same as in the primary sulfide below, although some massive concentrations do occur as vein-like fissures and as filling of breccia zones. Cuprite, tenorite, melaconite, malachite, and azurite occur but are not abundant. Lying between the chrysocolla horizon and the primary sulfide is a transition zone whose limits are irregular but seldom with vertical range exceeding 50 ft. Chalcocite, cuprite, melaconite, native copper, and chrysocolla occur superimposed on the primary sulfides. Chalcocite replacement of chalcopyrite, as well as secondary chalcocite, do occur. The primary sulfide minerals are chalcopyrite and pyrite, with minor amounts of bornite and covellite. There are no appreciable gold or silver values, and molybdenite has rarely been noted.

Jan 1, 1985

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

By Fred Pena

The VERTIMILL has proven itself to be a reliable performer in heavy duty industrial applications. Applications have been extensively used in the mining industry, flue gas desulfurization applications, and industrial minerals field. The machine is a vertically stirred machine that utilizes a screw operating in a grinding media. Grinding media types have ranged from several sizes of steel balls as the most common to pebbles or ceramic media. Mesh-of-grind and final product size are the determining criterion for the selection of the media size used. Product size consists have ranged from very coarse to super-fine grinds of less than 25 microns. Savings in consumption of power, grinding media, and liners when compared to a conventional ball mills, have been realized. Savings in consumption of reagents have also been demonstrated.

Jan 1, 1992

By J. C. Zelanko

The U. S. Bureau of Mines conducted a multi-faceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps in that the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements, and microseismic monitoring as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading, and microseismic activity were monitored prior to, during, and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and after the face bump. Shield load data which were evaluated in an effort to identify trends which could be used to forecast coal bumps appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1991

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By M. P. Oommen

This paper provides a brief look at a proposed short-longwall for coal, development. The proposed method is an attempt to realize the advantages of longwall mining in deposits that, historically, would only be minable by continuous mining methods. An overview of the proposed layout, development requirements, production rate, ventilation scheme and other associated features is provided. This mining method could help operators in above-drainage seams where minable areas are smaller. It may also have application in areas that are peppered with gas wells and in environmentally sensitive areas which preclude the use of conventional longwalls.

Jan 1, 1993

By P. Shang

Fly ash and zeolite have strong absorption to cations since their porous microstructure. The porosities of fly ash and zeolite can also be increased by modification, which improves the absorption of the materials. This research showed that the effects of modified fly ash and zeolite to remove ammonia nitrogen from rainwater. The optimal reaction time, additive amount of materials, and pH value of the stormwater to remove ammonia nitrogen were experimentally determined. For modified fly ash, the optimal removal rate of ammonia nitrogen from 100 ml stormwater was 74.41% with the addition of 10.0g fly ash, 1.5 hours of the reaction time, and 8 of pH value. To the modified zeolite, the optimal removal rate of ammonia nitrogen was 51.22% at the reaction conditions of 2.0g of zeolite, 1 hour of reaction time, and 7 of pH value.

Jan 1, 2010

By J. P. Ducarme

The eastern U.S. contains vast reserves of thin seam coal deposits, particularly in the Appalachian mountain region. These typical 355 to 710 mm thick reserves are difficult or uneconomical to recover with present technology. The U.S. Bureau of Mines is developing technology that would allow nearly 100% recovery of thin seams in these mountaintop regions. This paper details the research that has been conducted on these new techniques and presents results of testing on a cross-ridge full-scale physical model.

Jan 1, 1994

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By D. Gatzemeier

The Jewett mine is a surface mine in central Texas, producing about 8,000,000 tons/year of lignite. The mine covers 46,000 acres of land. Approximately 430 people are employed by Northwestern Resources Company and through their efforts, the Jewett Mine is one of the most productive mining operations in the country. The Jewett Mine utilizes a unique structure of staff to convert Operations Research into plans which can be implemented at the "front line" level of the Operations Team. This planning not only makes the mine cost effective and efficient, but promotes creativity in mining, which promotes ongoing research to lower the cost of mining.

Jan 1, 1993

By Todd Wanless, Daryl Poduska, Prakash Donde, Mahmood Khwaja

"The proposed Minne Lusa Stormwater Conveyance Sewer is part of the Phase 3 Major Combined Sewer Overflow projects to be scheduled as part of the City of Omaha’s Long Term Control Plan (LTCP). The system features a 6,100 foot long, 14-foot inside diameter tunnel to provide for conveyance of separated stormwater from previously completed and future LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The tunnel will operate as a pressurized system and convey flows of up to 2,500 ft3/s resulting from a 10-year, 24 hour storm event. This paper provides a synopsis of the project with a focus on the overall design aspects related to siting the tunnel alignment in an urban environment, the hydraulic analyses performed to choose a pressurized system rather than an open channel system, and expected geologic conditions. Tunnel alignment and profile and geological profile are presented, as well as an overview of the construction related impacts considered during design. PROJECT BACKGROUND The proposed Minne Lusa Stormwater (MLSW) Conveyance System will provide for conveyance of separated stormwater from previously completed, and future, LTCP sewer separation projects to the expanded Storz West and Pershing Detention Basins and subsequently, the Missouri River. The project location is representatively shown on Figure 1; the overall conveyance system is represented in Figure 2. The MLSW Conveyance System consists of three separate construction contracts under Contract Numbers: OPW-52004 – The Storz West Detention Basin to 31st & Paxton Tunnel; OPW-52454 – The Storz West/Pershing Detention Basin Grading and Improvements; and, OPW-52752 – The Pershing Detention Basin to ML Outfall Channel. This paper focuses on the project covered under Contract OPW-52004: design and construction of an approximately 6,110 feet 14-foot inside diameter (ID) tunnel, constructed using a Tunnel Boring Machine (TBM). The tunnel will receive flows from the Paxton Boulevard (PB) and the John Creighton Boulevard (JCB) Stormwater Conveyance Sewers and convey the flows to the Storz West Detention Basin, resulting in CSO volume and flow rate reductions to the Minne Lusa Outfall Channel and the North Interceptor."

Jan 1, 2016