Search Documents

By Eleanor Kentish, Nathan Bond, Edward Batty, Simon Webber, Alan Skarda

"Crossrail is Europe’s largest construction project — a new 100km rail route running through central London. A joint venture of BAM, Ferrovial and Kier (BFK) has constructed the tunnels and escalator shafts at the new Bond Street and Farringdon Stations. The recent trend in the UK industry towards sprayed secondary linings is driven by the potential for significant savings in cost and time. BFK is unique within Crossrail by constructing both sprayed and cast secondary linings. This paper presents a direct comparison between sprayed and traditional cast in situ secondary linings at Bond Street and Farringdon Crossrail Stations. An objective comparison is drawn between procurement and mobilisation periods, production rates, flexibility, tolerances and logistics in the tunnels. The technical challenges surrounding cast and sprayed secondary linings are explored, and recommendations are made of how each method could be improved for future use. INTRODUCTION It is well established that sprayed concrete offers a fast and effective method to seal the face of an excavation. In a relatively short space of time, sprayed concrete can be applied to an open face to support the short term ground loading on the tunnels during construction. Advances in sprayed concrete lining (SCL) technology — such as the use of wet mix processes, improved accelerators, fiber reinforcement, remotely controlled spraying robots, innovative surveying equipment and nozzleman competency schemes — have greatly increased the speed and safety of tunnel excavations using this technique. As a result, design engineers have become increasingly confident to use SCL primary linings as part of the permanent structural lining (Su 2014). Historically, long term ground and water pressure loads have been considered to be carried by the main structural or secondary lining, constructed using cast in situ concrete (Pickett 2014). However, the advances described above have made sprayed secondary linings a viable option, which has already been proven on the A3 Hindhead Tunnel (Arnold 2012). Sprayed concrete secondary linings offer potentially significant savings in cost and time during the construction process. The contractor does not need to procure a bespoke formwork system for each different sized tunnel — the SCL plant required is already on site for the primary lining. Each bay is sprayed with accelerated concrete, becoming self-supporting almost immediately — compared to moving and resetting the shutter, pumping concrete and waiting for it to cure. With sprayed concrete, working sequences and cross sections can easily be changed."

Jan 1, 2016

By T. Martinez Patino

Precious metals have been sought by man through time. The search has been the cause of many historic events as well as the founding of the famous Mexican, Minion centers of Durango, Guanajuato, Zacatecas and others. Bacis, a silver - cold deposit in the State of Durango was one of the lesser known centers established during Spanish colonial times. During the past year, metal prices have suffered a substantial decline, resulting in the closure of many mines. Through astute exploration, development and exploitation of the mine, the effect of the low prices has been offset and the mine is surviving these hard times.

Jan 1, 1994

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By William E. Spence

Gold was discovered at the Haile mine in Lancaster County, South Carolina in 1827 or 1828, and since that time the mine has been worked intermittently by both open pit and underground methods until its forced closure in 1942 by World War II. Production figures are incomplete, especially for the early years, but the total gold produced is estimated to have been greater than 200,000 ounces. Thus, the Haile mine has been the most productive gold mine in the eastern United States. The upper, residually enriched ores were relatively rich, but the bulk of the production has come from the mining of lower grade ores.

Jan 1, 1978

By J. H. Hill

The globalization of mineral markets and intense competition in downstream mineral-consuming industries such as transportation, agriculture, and construction are requiring raw materials suppliers to innovate, improve quality, invest in new technology, and control costs. Mineral specifications are becoming more refined, and pressure to improve products is felt from increasing numbers of competing producers, substitute materials, customers, and regulators. As a result, engineered mineral products are becoming more like manufactured ones in terms of cost structure, differentiation, and the importance of market driven, customer specific product development. Engineered mineral products are defined as those where the costs of refining and upgrading outweigh those of conventional mining activities (blasting, crushing, classification, haulage etc.), and where close control of physical and chemical parameters is required for customers' processing and manufacturing applications. This includes industrial minerals such as calcium carbonate, kaolin, mica, specialty oxides, talc, and some metal powders. It excludes most metals and bulk commodity materials such as gypsum, lime, sulfur, and soda ash. Engineered mineral products are utilized in common household goods, and are at the forefront of industrial materials engineering in plastics, ceramics, composites, glazes, coatings, and construction materials. As a group, they introduce interesting questions to the minerals firm. Advanced materials or basic? Diversify or specialize? What are the implications of advanced materials and for mineral markets, and most importantly, where can the producer look for long-term value, volume, and profits?

Jan 1, 1993

By S. Nygren

Nalco Chemical Company and a North Carolina Phosphate operation have formed a successful supplier/customer team effort that has resulted in major improvements in the operation of the clay thickening circuit at the Aurora, North Carolina concentrator. A Nalco OPTICUS® Automated Process Control System for thickener and flocculant control was installed in 1994. The paper will discuss in detail the development and refinement of the OPTICUS system over the past three years. The paper will survey the development and networking of process control for monitoring, controlling and operating four 325-foot Dorr-Oliver thickeners, three 80-foot high-rate Enviro-Clear thickeners and control links to the facility's clay/gypsum blending operation.

Jan 1, 1998

"Increasing demand and market economics have pushed the mining industry to adopt improved mining practices and minimize losses. Simulation, in this regard, has proved to be an efficient tool to help in decision making purposes. We present the development of a discrete event simulation model for a large-scale open pit mine to run experimental scenarios for near optimal decision making. A mixed integer linear goal programming (MILGP) optimization model is also presented for shovel allocation optimization. The mathematical model will be coupled with the simulation model at the dispatching stage for shovel allocation optimization and thus it will act as the link to optimal short-term schedule to assist in achieving better mine plan compliance across short-term and operational planning time horizons. The main contribution of this work so far is the development of the MILGP model and development, implementation and verification of the simulation model on a large scale oil sands open pit mine case study. The results obtained so far are promising and have been validated against the historical data of the mine, proving the applicability of the model for experimental scenario analysis. INTRODUCTION It is essential for mining operations to adopt efficient operational methods and technologies to cope with market demand and economics. Mining operations, on the other hand, being capital intensive, find it risky to bring in any changes. Simulation is a tool that can help in this regard for better decision making purposes with an improved and quantitative measure of confidence. A true representative model that satisfies the objectives set for the simulation is essential to achieve its applicability for decision making purposes. A similar simulation model is presented in this paper for analyzing the operational KPIs of a large scale oil sand open pit mine with truck-shovel operations. This paper is aimed at providing an overview of the development of the model and the statistical outcomes validating its applicability for experimental scenario runs and thus for better decision making purposes. A mixed integer linear goal programming (MILGP) optimization model is also presented in this paper that acts as an upper stage in a multi-stage dispatching system. The optimization model is proposed to be linked with the dispatching logic in the simulation for optimal shovel assignments and target productions by reading available mining faces directly from the short-term extraction schedule. This model is aimed at bridging the gap between operations and short term extraction schedule; and may help achieve better compliance between the two."

Jan 1, 2015

By J. Gallagher

Henderson Mine has been transporting molybdenum ore using a rail haulage system for the past 21 years. Due to the age of this system, limited performance, and obsolescence, a capital investment decision was imminent. Henderson used this opportunity to evaluate other transportation methods and continuously improve their mining practices. These efforts resulted in a new mine plan for Henderson, which ensures that Henderson will continue to supply high quality molybdenum into the 21st century. This paper will discuss the dramatic changes taking place at the Henderson Mine as a new production level is mined. These changes include the installation of an underground crushing, conveying, and truck haulage system, as well as increasing the scale of the panel caving process. Each of these topics will be discussed, as will their rock mechanics and material flow implications.

Jan 1, 1998

By Darrell E. Young

This presentation will define what talc is, how it is mined and processed, and how talc is used in the paper industry. It will also give you some idea about who Luzenac America is and from where it came. Luzenac America was formed in July, 1992 as a result of the acquisition of the talc assets of Cyprus Minerals by RTZ of the United Kingdom. Cyprus Industrial Minerals was then merged with the other RTZ talc interests under the Luzenac name. Luzenac is a town in the Pyrenees of Southern France -and the home of Talc de Luzenac, RTZ's first talc acquisition. The Luzenac Group is the largest talc producer in the world.

Jan 1, 1993

By Carlos A. Jaramillo, Seng Hing Ngu

"The Murum Hydroelectric Project is a 944-MW development consisting of a 145 meter high RCC dam, two 2660 meter long, 9 meter excavated diameter upper pressure tunnels, surge shafts, two 950 meter long 7 even meter OD penstock tunnels and a surface powerhouse. The project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometer from Bintulu, in the Rajang Fold-Thrust Belt, an Upper Cretaceous to Upper Eocene fold and thrust belt that extends under most of Sarawak. The Belaga Formation consists of a thick sequence of deep marine sediments currently appearing as steeply dipping strata of thin to thick bedded, fine to medium grained sandstone interbedded with argillaceous rocks, resulting on a “Flysch” type geologic environment. The project pressure tunnels were excavated perpendicularly to these strata resulting on frequent change on rock conditions and behavior, and required rock support. This paper describes the characterization of the rock mass, design of rock support, and incidents during construction. Particularly interesting were convergence issues in Tunnel 1 resulting from Tunnel 2 excavation. INTRODUCTION The Murum Hydroelectric Project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometers from Bintulu, and upstream of the Bakun Hydroelectric Project. The project consists of a 145 meter high RCC dam, a 50 meter high intake tower, two nine meter OD and 2660 meter long upper pressure tunnels, two nine meter OD and 175 meter long vertical shafts, two 25 meter diameter and 80 meter deep surge tanks, two seven meter OD and 950 meter long penstock tunnels and four seven meter OD and 50 meter long branch tunnels, two 8 meter diameter to 3.4 meter diameter and 1400 meter long penstocks installed within the shafts, penstock tunnels and branch tunnels ending in a powerhouse with 944 MW installed capacity. LAYOUT OF THE WATERWAY TUNNELS The two waterways tunnels are basically parallel as shown in Figure 1, with each tunnel supplying water to two units in the powerhouse. The tunnels start separated 25 meters center to center, but 250 meter from the intake the separation increases to 35 meters. The tunnels are lined with reinforced concrete until they reach the surge shafts and steel lined from there to the powerhouse. The tunnel profile is shown in Figure 2."

Jan 1, 2016

By Y. F. Vasyuchkov

In general a term "unconventional mining or "non-traditional mining technology" getting more and more familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in Figure I:

Jan 1, 1997

By Olivier Kraft, Olaf Kortz

"Project-specific optimized tunnel boring machines represent the spearhead of technological progress in tunneling because with their use, very long-lasting, high quality tunnel structures in almost any geology, depth and topography can be produced with a high degree of automation. The mechanized excavation of tunnel structures ensures the greatest possible environmental protection during tunneling itself. Professional, systematic and high quality rebuilds and reuse of already proven equipment also ensures maximum efficiency in the use of materials and energy resources. It offers an enormous potential for a highly optimized environmental balance. Here the manufacturers of tunnel boring machines and their users in particular have a duty to ensure transparent, high quality and binding standards in the entire rebuild cycle and in the refurbishment management of innovative tunneling technology. This paper deals with the comprehensive processes with rebuild levels of tunnel boring machines and highlights some exemplarily implemented projects. 1 INTRODUCTION All over the world, the number of tunnel boring machines (TBM) in which equipment rebuilds from previous projects are re-used has increased over the last few years. This text presents the technical and economical aspects of this market development. It also takes a look at the practical implementation of rebuild measures. The ""ITAtech Guidelines on Rebuilds of Machinery for Mechanized Tunnel Excavation"" from 2015 lay down the requirements that the machine manufacturers must meet. 2 ECONOMICAL AND ECOLOGICAL ASPECTS OF RE-USING COMPONENTS The globalization of the construction sector and the consideration of environmental aspects promote an increased re-use of machines and machine components. Nowadays, large-scale construction projects are often carried out by international joint ventures of several individual companies that are established specifically for this purpose. After the completion of the project, the joint ventures are dissolved and they liquidate their project-specific equipment, such as tunnel boring machines. Today, it is much more uncommon for such machines to remain permanently in the possession of construction companies. Joint ventures offer TBMs on the free market, or they exercise contractually agreed repurchase options with the manufacturer. On the whole, this increases the number of re-usable components or complete tunneling systems available on the market."

Jan 1, 2016

By D. Farnell

Large semi-autogenous (SAG) or autogenous grinding mills have become the work-horse of the modern high volume concentrator. They typify the economy of scale - fewer, larger machines doing more work, more economically. With fewer machines, equipment reliability becomes of paramount importance. Realizing this, companies installing new or modernizing existing facilities have placed extraordinary emphasis on purchasing a reliable mill. This, in turn, has had a significant impact on mill design. Kennecott And Codelco - Two Different Approaches Last year, two of the world's largest copper producers, Codelco and Kennecott, undertook the modernization of their main grinding facilities at Chuquicamata and the Utah Copper Division (UCD) respectively. Both selected semi-autogenous milling and both, recognized the importance of the reliability of the primary mills. Each, however, decided on a different approach to optimizing reliability. Codelco placed the emphasis on technical innovation in design and opted for a gearless driven mill. Kennecott chose the more conservative approach of active participation and exceptional quality assurance in mill design and manufacture.

Jan 1, 1987

By C. P. Davenport

At the risk of belaboring certain facts which have so often been stated in the past, please bear with me while I set the stage. What are the projected electrical power needs of the nation and of the Northwest during the next 15 to 20 years? No one who has researched the subject over its historical past has reached a substantially different result than the following simple conclusion: electrical power requirements are doubling every decade. There are some who question the necessity of a power company's need to install capacity every ten years equal to what it has done during its entire previous history; there are even those who would argue that such growth should be arbitrarily curtailed. We are not here today to decide who should have light, heat, jobs and comfort, for we know that a power company must, by law, meet its responsibilities of providing the energy the public expects when the switch is thrown. The Northwest area (the States of Oregon and Washington), for which I speak, has the same case history of electrical power need as does the nation as a whole, and the requirement boils down to roughly an average of a million kilowatts of new capacity each year over the next ten years and we can estimate an average two million kilowatts per year in the 1980's. This is simple arithmetic, but the problems of meeting this exhausting schedule are a real challenge. The subject to which I address this paper is the role that Western Coal will play in the 6 billion dollar investment in these power generation stations. That 6 billion dollar figure represents today's dollar value and you may wish to apply your own escalation - frankly, I haven't the courage.

Jan 1, 1972

By G. M. Rao

It has been a universal observation that rich grades of ores and minerals are getting depleted, simultaneously the demands for civilization are ever increasing coupled with occurrence of poor grades of ores and minerals posing a problem to the processing engineers. At the same time, the cost of mining and milling are increasing, creating a situation where the management has to handle and process low grade ores at an economic level keeping environmental stipulations and control to be safeguarded which has been an additional cost for the management to comply with.

Jan 1, 1994

By A. B. Mayer

A generic task summary for design and implementation of hydrogeology programs at open-pit mine operations is presented as a guideline for management. Rigorous assessment of the local and regional hydrogeologic system is necessary to plan dewatering activities and to address environmental concerns. Dewatering activities include calculation of dewatering requirements, design of dewatering systems and evaluation of dewatering-water disposal areas. Environmental concerns include calculation of dewatering and water-disposal impacts, mitigation of soil and ground-water contamination and acquisition of water rights. Three-dimensional numerical models are commonly used to support these analyses. A thoroughly developed hydrogeology program provides an interactive basis for dewatering feasibility decisions and for support of environmental permits and regulatory compliance.

Jan 1, 1993

By W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By Karl Ingmarsson

Larger mines spend millions of dollars annually on rock drilling tools, but often purchase based on historic consumption. The results vary from excess inventory to acute tools shortages. These lead to emergency sourcing, sometimes mixing products that don’t perform optimally. Boart Longyear analyzed the usage pattern of 96 thousand drill bits at thirteen different underground mining contracts, showing very high variability. The monthly standard deviation on a product level was 42%, with the highest for development and low volume bits. A new rule of thumb is suggested to carry only one month of safety stock for high volume bits, but increase to three months for low volume bits. This balance will reduce the risk of outages with less inventory. The accuracy can be improved by considering the specific conditions at each mine and reclassifying individual bits for a different safety stock level. Root cause analysis and collaborative forecasting between mines and suppliers can lead to further optimization of availability and inventory levels.

Feb 1, 2024

By N. Rocco, G. Johnson

Implementation of post-closure draindown estimates for tailings facilities are important predictive tools for reclamation planning and often influence jurisdictional bonding. Simplified estimates of draindown have been proposed in the past but these methods are not able to capture many of the site-specific nuances as well as operational and material parameters that influence robust draindown estimates. This paper discusses an iterative approach that relies on unsaturated flow models to predict draindown rates and associated pond inventory water balances that track inputs into underdrain pond systems, solution storage volumes, implementation of active evaporation, and necessary recirculation of solution back to the tailings facilities. Specific design criteria such as climate, facility geometry, material properties, and initial conditions, as well as active closure operational considerations that can influence draindown estimate will be discussed. Concepts presented will be valuable for operators, designers, and regulators to guide closure planning and predictive analytical analyses that support draindown estimates.

Mar 2, 2022