Search Documents

By Wen H. Su

This paper examines the intrinsic mechanisms of cutter roof by combining field investigation, laboratory testings, underground instrumentations, and numerical modelling. Cutter roof developed during the development of a set of longwall panel entries in a West Virginia coal mine was presented as a case study. Mining alternatives applicable to the mine are recommended. Cutter roof occurred in two other West Virginia coal mines were also investigated Detailed comparisons were made among the three cases. As a result of the extensive investigation, intrinsic mechanisms of cutter roof failures under various conditions are presented from the practical and theoretical points of view.

Jan 1, 1985

By W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of freshwater whose origin can be traced to the present and historical courses of the River Indus. In the past the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water-table has risen to within a few feet of the surface. The river system itself is being progressively developed for irrigation and very shortly a situation will arise where the entire low winter flow will be utilised. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilise the water-table at safe depths. This paper discusses some of the methods used to ensure optimum-economic development of the fresh groundwater and describes the general design philosophy evolved by the authors firms for both irrigation and drainage wells, with respect to both well configuation and operation. Water quality standards are discussed in as much as they affect subsequent use of the groundwater. A few particular aspects are considered, including that of the values of the relevant aquifer constants, the construction of wells and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to-produce fresh water from layers overlying saline water. This solution is also discussed.

Jan 1, 1967

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By V. I. Lakshmanan

Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market. Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogenous grinding. In addition to producing marketable coarse graphite by such autogenous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies.

Jan 1, 1984

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays.

Jan 1, 2013

By B. Simser, T. Butler

Glencore’s Nickel Rim South Mine, located in Sudbury, Ontario, Canada, is a primary/secondary blasthole operation with ore zones lying between 1,100 and 1,700 m below surface. One of the main benefits of the primary/secondary mining method in high stress ground is that up to 50% of the mining will take place in secondary stopes that should be in a yielded rock mass state. Every future secondary mining stope begins as a primary stope abutment pillar. As with many mines, the stress loading history and rock mass conditions can vary considerably in space and time. Safe mining practices cannot allow for an assumption that the planned secondary stopes are indeed yielded. An incorrect assumption can result in mining development and stoping taking place in high stress ground rather than the expected yielded rock mass conditions. This can result in higher levels of seismicity than expected and incorrect ground support recommendations in areas where workers could be exposed. Seismic monitoring is the mines’ premier tool to track the actual rock mass response to mining. Yielded zones have a reasonably clear seismic signature/pattern over time that is visible in the collected data. The ability to accurately locate small magnitude seismic events can help define and delineate different stages of rock mass failure. The vast majority of the seismic data recorded by the microseismic monitoring system is below moment magnitude (Mw) 0.0. Examples are provided showing how small seismic events (Mw < -1.5) can help provide feedback from the rock mass deformation that allows the ground control engineer to gain a better understanding of how the rock mass is responding to mining processes.

Apr 26, 2022

By John W. Tieman

The increasing magnitude of our nation&apos;s pollution problems seems to stem from two main factors: urbanization and technical advance. In 1920, less than half the country&apos;s 106 million people lived in cities. Forty years later, the urban population accounted for 70 percent of the nation&apos;s 179 million. It is predicted that by the end of the century, 95 percent of the U. S. population, estimated at 280 million, will live in urban areas. As these people live increasingly in city concentrations, their residues also concentrate. With technological advances to support the increasing population, the variety and quantity of goods that we use also increases. New materials and processes result in increases in pollutants, some of them new. The harmfulness of these pollutants is sometimes known, but sometimes only suspected. One pollutant of concern at the present time is sulfur dioxide, the product of combustion of sulfur-containing fuels. Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930&apos;s, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased. Although many state-of-the-art papers have deluged the literature during the past several years, the research going on in the area of sulfur oxides control is of such importance that periodic reviews are justified. It is the purpose of this paper, therefore, to again review the state-of-the-art, but this time from the stand-point of what is immediately commercially available

Jan 1, 1972

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By W. K. Summers

During the past few years monitoring systems have been installed to measure the effects of environmental changes on the ground-water resource. The design of a monitoring system depends upon the designer&apos;s perception of how the environmental factors merge with his perception of the ground-water flow system. The validity and representativeness of measurements made during a monitoring program depend upon the validicy of the designer&apos;s perceptions and concepts. To optimize the design of a ground- water monitoring program the designer should make preliminary measurements to confirm his assumptions.

Jan 1, 1985

By S. M. Moore, J. F. Burr, R. Fernando, D. Snyder

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done. As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal. TECHNOLOGY GAPS TARGETED BY THE MINER ACT The MINER Act addressed several technology challenges: • Problems with donning and switching between self-contained self-rescuers (SCSRs). • Poor visibility in smoke. • No wayfinding assistance for escape from the mine. • Limited breathable air supply. • Inability to locate trapped miners. • Inability to communicate with trapped miners. • Failure of mine seals. The MINER Act had several provisions that prescribed specific safety technologies intended to address these issues. Many of these were directed at post-accident technology requirements — an area in which Congress mandated additional technology investment. Specifically, the Act required mine operators to submit emergency response plans (ERPs) that contained provisions for implementing new or improved post-accident communications, tracking, lifelines, refuge alternatives and breathable air supplies along with training for emergency procedures and local coordination of emergency response. Most of the requirements were to be carried out within three years of the ratification of the MINER Act. In addition to these requirements for mine operators, the Act clarified and expanded NIOSH’s role and authority in enhancing the development of new mine safety technologies and expediting their commercial availability. The MINER Act also required NIOSH to develop research on refuge chambers, mine seals and the use of belt air and fire-retardant belts. Mine seals had to be upgraded and MSHA turned to NIOSH for applied research to establish the new explosion-resistance requirements. Progress toward closing the gaps."

Jan 1, 2017

By R. L. Grayson

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition, and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1996

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By R. Jin

The hydrophobicity of six coals ranked from lignite to anthracite is studied through contact-angle measurements, bubble attachment-time measurements, FTIR spectroscopy, and Hallimond-tube flotation. The preliminary study shows that the hydrophobicity of coals can be told by the bubble attachment times of coals (a kinetic criterion) or by the contact angles (an - equilibrium criterion). A general agreement between flotation response of coals and measured bubble attachment times or contact angles is observed in the present study. However, the study also shows that the hydrophobicity of coals can be predicted by FTIR spectroscopy work with proper manipulation of the spectra. Both hydroxyl and carboxyl groups in the coals are proven by FTIR work to be responsible for the change of coal hydrophobicity. A new criterion for the hydrophilicity index of coals from FTIR spectra is introduced through the study.

Jan 1, 1987

By J-Y Chen

China was once deficient in nickel and almost totally reliant on imports for its domestic needs, supplies mainly coming from Canada since the ending of imports from the U.S.S.R. in early 1960&apos;s. However, the discovery of the huge nickel/copper sulphide deposit in Jin Chuan, Gansu Province of northwestern China in late 1950&apos;s and its development and construction through the 1960&apos;s and 19701s, have much improved China&apos;s domestic nickel position. In 1985. China&apos;s nickel production has exceeded 27.000 tons, compared with only 7,000 tons in 1977. Today, Jin Chuan Nonferrous Metals Company operates two underground mines and a small open- pit; owns China&apos;s largest reserves of nickel and platinum, and the second largest reserves of copper and cobalt; and has become the most important subsidiary of China National Nonferrous Metals Industry Corporation (CNNC) which was established in April 1983. The Jin Chuan nickel-copper mines are located in Jin Chang City, Gansu Province, 1,700 km west of Beijing in the People&apos;s Republic of China (Figure 1). It is believed that Jin Chuan mines have the second largest nickel reserves in the world, after Sudbury basin, Canada. The deposits are situated on the north slope of the Longshu Mountains, 50 km north of Jin Chang City, and border on the southmost edge of the Gobi Desert plateau. The deposits were discovered in 1958. The total strike length of mineralized zones was approximately 6.5 km long, which was divided into four mining areas by faults (Figure 2). The Longshu underground mine of No. 1 mining area began development in 1959, with full ore production capacity of 1,000 TPD. The open-pit, also in No. 1 mining area, which was brought into operation in 1966 with ore output of 5,500 TPD, was closed down in 1982. The East Extension of the open-pit was put into operation in 1983; present production capacity is about 2,200 TPD. Nickel production of Jin Chuan mines in recent years, and production capacity of each mining operation, are shown in Tables 1 and 2.

Jan 1, 1987

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry&apos;s supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations&apos; average Cost of capital.

Jan 1, 1969

Column flotation cells continue to gain acceptance in the coal industry for the treatment of high-ash streams containing clay slimes. Unfortunately, some industrial installations have failed to meet expectations due to improper scale-up, incorrect operation and poor ancillary circuit design. To overcome these problems, case studies have been conducted to fully define the capabilities of column cells for coal applications. These data have been used to develop generic engineering guidelines for column circuit design and operation. An economic analysis has also been conducted to illustrate the importance of key capital cost considerations. These analyses indicate that column cells are significantly more expensive than conventional machines, although this difference can be greatly reduced through the installation of very large-diameter columns.

Jan 1, 1999

By John R. Gaines

I am not a member of AIME, and this is my first annual meeting. As a lifelong member of the non-ferrous metals industry I have enjoyed listening today to speakers point with pride and view with alarm the public relations activity or lack thereof in the halls of government, as well as at the grass roots. There is much to be alarmed about, to be sure, but also some accomplish¬ments to be viewed with pride. Other speakers have given a broad overview of our industry&apos;s relations with their several publics. I will be specific about two incidents in which The Anaconda Company faced the loss of confidence of a large portion of its publics: the nationalization of our properties in Chile in 1971 and the closing of our under¬ground mines in Butte, which was announced last October. If I have a minute left over, I will speak about our concern for the loss of confidence in business institutions which has been re¬vealed in recent public opinion polls.

Jan 1, 1975

By Carl P. Venzke

Mining lignite in the Gulf Coast often requires some interaction with shallow ground water system. Suggestions for determining ground water data and analysis requirements for regulatory compliance are given. Simple methods for estimating mine inflow seepage, ground water level declines, and changes in ground water chemistry, which may result from mining, are discussed. The mining of lignite often results in interaction with shallow ground water systems. An evaluation of the interaction is required as input to mine permitting and engineering. Your evaluation will proceed more smoothly and produce more meaningful results with some planning prior to performing your evaluation. The following are tips to consider in planning and carrying out a successful study.

Jan 1, 1982

By A. K. Sinha

A great potential market for the high BTU midwestern thermal coal exists if the coal is desulfurized and prepared to meet the environmental restrictions and the utility customer specifications. Because the midwestern coal is very high in pyritic sulfur, it can be adequately desulfurized by removing the pyrite with the help of such coal cleaning techniques as the froth flotation. Froth flotation cells are now commonly employed in modern coal preparation plants for recovering the fines but they are not utilized for desulfurizing the coal probably due to a lack of system operating data for such applications. A research project recently conducted at Southern Illinois University shows that the total sulfur in the midwestern coals can be successfully reduced from as high as 5.3 percent to less than 1.4 percent by single stage froth flotation. The results obtained on ten different samples of high sulfur coal obtained from different areas in the Illinois Basin are presented and discussed.

Jan 1, 1985