Search Documents

By J. L. Schroder, William J. Halvorsen, Wiliam W. Lyons, Kent C. Ware, Sheridan A. Glen, Donald C. Simpsom

The prospects for near-term growth in coal demand are exceptional: the federal government recently targeted 141 oil- and gas-fired generating units for mandatory conversion to coal; coal-to-synfuel developments are proceeding at a steady clip, with construction of a $1.2 billion gasification plant to begin this year in Beulah, ND; uncertainty over nuclear power and stratospheric oil prices enhance the steam coal market; the export market is ripening; and an influential new political force (the Senate Coal Caucus and Congressional Coal Group) is flexing its muscles on Capitol Hill. But the rosy picture is muddled by signals, often conflicting, sent out by federal agencies. Although EPA can be credited with relaxing its grip on the Clean Air Act, its sulfur dioxide control strategy is still often at odds with the Administration's call for domestic energy (coal) development. B. R. Brown, president of Consolidation Coal Co., sums up the situation: "Every mule is pulling in a different direction." Often in the midst of the fray is the small operator who has been hardest hit by the stagnation of coal markets. Layoffs, shortened work weeks, and mine closures were rampant in the eastern and midwestern coal fields, even among large producers. The longstanding boom in western coal was tempered during 1979 by a noticeable slowdown in announcements of new mine construction. The prognosis: Eastern coal will remain in the doldrums for quite a while to come as it works off some 90 Mt of overcapacity. Midwestern coal will fare no better due to the regulatory-influenced appetite of midwestern utilities for low-sulfur western coal. This displacement should ease, though, as new power plants equipped to burn high-sulfur coal come on line in the years ahead. In the West, the National Coal Association projects production to increase a healthy- 10% this year, although mine-to-market transportation looms as the single largest stumbling block to marketing efforts. Fatalities Up 40% in 1979 The National Coal Association estimated total coal production in 1979 at 671 Mt, an increase of 13% over 1978. Of this total, the East and Mid-west accounted for 476 Mt (71%) and the West produced 195 Mt (29%). With the consistent rise in western production playing against flat outputs in the East and Midwest, underground mining's share of total production continues to slip and is expected to account for only 38-39% in 1980. Incidence of deaths and injuries at US coal mines soared in 1979 over 1978 rates. MSHA figures (still subject to final adjustments) reveal a death rate of 0.07 per 200 000 man-hours, up 40% over 1978's 0.05 figure. MSHA chief Bob Lagather attributed the death incidence to the large number of new coal mines put on line in 1978, which he estimated at between 350 and 400. Nonfatal injuries rose to 8.48 per 200 000 man-hours, up about 15% from a 1978 rate of 7.35. In absolute numbers, MSHA counted 144 fatalities and 18 111 lost-day injuries during the 1979 calendar year. The 144 coal mining deaths in 1979 is the highest number of coal fatalities at US mines since 1975.

Jan 5, 1980

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By Daniel A. Servigna, Pedro V. Porcayo, Humberto F. Preciado

This case study presents successful conversions of two conventional slurry tailings storage facilities (TSFs) to filtered tailings storage facilities in Durango, Mexico, for two mining operations with production rates ranging from 1,200 to 4,500 t/d (1,320 to 4,960 stpd). In both cases, the decision to make the conversion was driven by: • Ability to increase the storage capacity via stacking of filtered tailings. • Reduction of the tailings’ impacted footprint. • Mitigation of long-term geotechnical stability risks. • Alleviation of environmental risks by reducing tailings water as a source of pollutants, and a net reduction in process make-up water demand. The case studies can be divided in two classes: class 1 facilities, where slurry tailings are loaded almost immediately with filtered tailings because of storage area limitations; and class 2 facilities, where the conversion is immediate but the available area allows gradual or eventual loading of the previously stored slurry tailings. The condition where slurry tailings must be loaded almost immediately represents the greatest engineering challenge because of the geotechnical risks of instability and liquefaction (under both static and dynamic loads). Regardless of whether these facilities are converted immediately or eventually, they all require monitoring of pore water pressure conditions within the slurry tailings being loaded as the depth of placement of the filtered tailings above the slurry tailings increases. Additionally, where loading rate exceeds the pore pressure dissipation rate, tailings dewatering may be required to increase the rate of consolidation and strength and mitigate the risks of foundation failure.

Jul 1, 2025

By P. Bevilacqua, M. C. Williams, T. P. Meloy

We will bet you that, without prior programming within 10 minutes, we can design and simulate a 10,000 unit operation separation circuit. We will even do it at your place. We do it all the time. [ ] There are no tricks; we do it in a spreadsheet. We do it in those user friendly spreadsheet such as Quattro Pro. Spreadsheets must be user friendly. Accountants use them as do managers, business men, lawyers, doctors and salesmen. What these users seldom realize, is how powerful a mathematical tool a spreadsheet is. Among their other capabilities, spreadsheets can do a finite element analysis. That is why they are useful for accounting. That is also why they are more useful to engineers in the mineral industry. Spreadsheets are ideally suited for the engineering problems in the mineral industry. We have used then for solving problems in: a) mine ventilation; b) circuit design and optimization of dense media, flotation and sizing; c) comminution circuit design; d) shaking tables; e) Humphrey spirals; f) sluice ways and channel flow; g) lock particle and liberation problems; h) tunnel and shaft stress problems; i) cascadograph simulation; j) complex heat transfer problems; k) flow in porous media; and sheet flotation (Figure 1). Mineral industry problems presented on or with a spreadsheet are an excellent teaching instrument, problem statement and solution tools and sales devices. Spreadsheets answer easily, quickly and reliably many mineral industry engineering problems. What makes spreadsheets so useful to the mineral industry. The short answer is: they are easy to use; mineral industry problems fit the spreadsheet format. Those reasons are part of the answer. The real answer lies with the structure of the spreadsheet itself. Essentially, a spreadsheet is a "finite element analysis" form of computer software. Many mineral industry problems are readily solved by finite element analysis techniques. While some in the mineral industry may think they have never heard of finite element analysis, most use it weekly if not daily. Any profit and loss statement is essentially a finite element instrument. In fact, any array of numbers where one number is related to another may be construed as a finite element analysis product. Finite element analysis is a common daily activity. To get an appreciation of a finite element analysis, think of a monthly sales forecast for the next year. For each product and for each month, there exists a dollar figure for the forecasted amount of sales. In the forecast statement, for a given product in a given month, there is a "box" where the forecasted figure is presented. The forecast figure in that box was arrived at through some type of formula. The formula probably required some information from other neighboring boxes in the master forecast statement. Voila, one has a finite element analysis. Today the analysis would be done in a spreadsheet. A typical mineral industry problem is ventilation in an underground mine. Think of a rectangular room and pillar mining operation. Each room has air entering at a given pressure and velocity and air leaving at another pressure and velocity. During steady state, the air entering and leaving the room is determined by conditions in the adjacent rooms. One can readily model the room and pillar mine layout in a spreadsheet, and then find the flow in and out of each room at steady state. Change the flow by moving a brattice cloth or blocking off a path way and one gets a new air flow profile. Change the numbers on the spreadsheet that reflect

Jan 1, 1993

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By Weixiang Meng, Zhao Song, Ming Guo, Zhigao Liu, Shoubao Zhang

"There are many multi-layer coal reserves in China which account for nearly 20 to 25% of the existing proven reserves. When the coals are mined in a descending order using the fully mechanized long wall mining method, they usually have roof collapse with cavity and air leak in roadways and long wall stopes; this is especially relevant when the thickness of the rock between two coals is less than 5.0 m, as the roof stability of lower seam would be greatly reduced. At the Wuhushan Mine, such abnormal strata behavior occurs, including abnormal support stress, irregular period roof pressure, and roof falls in the face. The main reasons for these behaviors include smaller roof thickness, lower rock strength, and mining influence of upper coal; these reasons were determined by analyzing the in situ conditions. A mechanics-based model of the mine geometry was set up to study the sources of stress, the stress evolution of coal, and the discriminant method of roof stability; to obtain the smallest safe thickness of roof between two coal layers, numerical modeling was applied to analyze the relations between the roof thickness and its displacement distribution. Based on the above research, the No.1001 face was divided into easy roof caving zone (ERCZ), roof caving transition zone (RCTZ), and unlikely to roof caving zone (URCZ). In the ERCZ, comprehensive grouting to reinforce the roof was implemented; in the RCTZ, local grouting to reinforce the roof was implemented. Furthermore, a face stability control index and its range were developed in a fully mechanized face combined with mine pressure observation. After implementing this strategy, there have been no unexpected roof caving or other serious strata behaviors.INTRODUCTIONChina is the country with the largest coal production in the world, and the conditions for its coal seams are particularly complicated. For example, in China’s Datong, Wuda, Pingdingshan, and Qinshui mining areas, there are a large number of multi-layer coal seams. The thickness of these coal seams ranges from 1.3 m to more than 10 m, and the spacing between layers is from under 1.0 m to over 30 m. A common problem with these coal seams is that one layer of mining has a large impact on other coal seams, which are customarily referred to as close-distance coal seams. According to statistics, close-distance coal seams account for about 20–25% and 15–18% of China’s coal reserves and production, respectively.From the reference research of Huang (1999, 2002, 2018) and Tu (2010, 2011) we can learn that in the mining process of close-distance coal seams, downward mining is mainly used. When the upper-layer coal is mined, it has a huge mining disturbance effect on the floor (that is, the roof of the lower coal). The mining disturbance increases the mining fissure in the rockmass and weakens the strata strength. The mining problem formed by this issue is that when the lower coal is mined, problems such as difficulty in roadway support, collapse of stope roof, and difficulty in ventilation are often encountered. Especially for the mining of medium-thick coal seam groups with a layer spacing of less than 5.0 m, there has been a large-scale roof collapse accident with a fall height of more than 10.0 m. In response to such problems, domestic and foreign scholars and engineers such as Tan, Zhao, and Xiao (2010), Xie et al. (2017), and others have also carried out targeted theoretical and practical research."

Jan 1, 2019

By Keivan PakIman, Maziar Pasdarpour

Transportation tunnels are highly sensitive to ground movements and are required to be stable and secure for safe operation. In urban areas, the interaction between tunnels and adjacent piles, which are widely used to support buildings and other structures, requires careful consideration. The seismic response of tunnels may vary depending on the lateral stiffness and strength of the tunnel walls, while the axial loading and seismic impact of adjacent piles may cause soil displacement and stress changes that can damage the tunnel lining. As a result, tunnel owners often impose strict limits on the design of new piles lying close to existing tunnels including maximum allowable tunnel deformation, stress change limits, and minimum tunnel to pile separation distances. This paper describes a numerical analysis of the inuence of the axial loading and seismic impact of bored pile foundations on subway tunnels, undertaen using the nite element software laxis D. ased on the results of the numerical analysis, the paper suggests a more realistic and less conservative approach for designing piles in close proximity to transportation tunnels. INTRODUCTION The interaction between tunnels and adjacent piles can cause stress changes and displacements in the soil and structures which may adversely impact structural performance and tunnel safety. It is therefore important to take account of relative load transfer and piling conguration when designing new piles in

Jun 23, 2024

By James W. Mahar

The following paper summarizes our observations on building response to mine subsidence and techniques for mitigation of building damage. The subsidence cases are located in Illinois. The general description of the geologic and mine conditions are primarily for those sites. Data on building response and mitigation measures were collected under grants supported by the Abandoned Mined Lands Reclamation Council (AMLRC) of Illinois and the U. S. Bureau of Mines, in Twin Cities, Minnesota. Case histories include pit and sag subsidence primarily beneath abandoned room and pillar mines. The majority of the paper deals with structures affected by sag subsidence. Most of the structures are one and two story homes. The first section of the paper summarizes the typical geologic and mining conditions at the sites. Building response to pit and sag subsidence follows the first section. Emphasis is placed on the behavior of concrete and masonry foundations, and wood frame and masonry superstructures. The third section describes mitigation techniques used to prevent or minimize building damage. A summary of the observations and critical parameters is given at the end of the paper.

Jan 1, 1982

By Colonel Oattis E. Parks

The quantity of coal recovered by diamond coring techniques is not sufficient in many instances to make meaningful coking and/or ash fouling tests. Quantities in excess of that obtained by conventional coring techniques, usually in amounts exceeding 500 pounds, has been designated bulk sampling. During the past three years, AMAX Coal Company has utilized five methods of bulk sampling. It was our desire to obtain a bulk sample that was diagnostic of the seam by the most expedient and economical method. From the beginning all of our efforts have been directed to methods which would extract the required coal from slim boreholes which provide quick and inexpensive access to the coal seam, regardless of depth, terrain and accessability. In our efforts and investigation several large diameter cores have been taken from thick coal seams at relatively shallow depths in easily drilled rocks. On the other hand, for deeper thin seams multiple large diameter coring is more expensive and time consuming. It is somewhat less expensive when multiple cores are taken from a single slim borehole utilizing deflection coring, although considerable skill is necessary.

Jan 1, 1973

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By W. Clark Ashby

Productivity is a fascinating concept. Like motherhood or apple pie, we know it as a good thing. Just what it means is not so clear. To a coal miner we assume it means tons of coal hauled from the mine. To the company president it means profit after capital, labor, and other costs have also been reckoned. To the government economist it means output in a balance of payments. What does it mean to the biologist, and can reclamation really be productive? In this paper we discuss productivity from a biological viewpoint, give some yield data for various types of reclamation plantings, and discuss how our demand for or acceptance of differing kinds of productivity is tied up in bigger questions of land use, environmental stability, and resource allocation.

Jan 1, 1981

By Allan M. Harvey

Asbestos production in the United States is no match for the vast operations of Canada and the U.S.S.R. The majority of U.S. production is limited to the states of Vermont, California and Arizona, and the type of asbestos is limited to the variety of serpentine known as chrysotile. What little production of other varieties of asbestos such as tremolite and anthophyllite that has occurred over the past 100 years since asbestos became a useful commodity is of practically no significance. However, new developments in the field of environmental and occupational health hazards has startled the mining industry in this country and has already given a few particular companies reason to be concerned about the profitability and probability of their continued operation in the business of mineral processing. At the heart of these developments is the question and controversy over just what constitutes asbestos and what exactly is the definition of a fiber. To the mineralogist or, in fact, to practically anyone engaged in the process of mining and separating minerals there is little or no question about asbestos. It is not a distinct mineral but rather a commercial product serving specific applications for which a number of fibrous mineral types can qualify. To the hygienist pr health authority this definition is too general. They demand something they can detect, measure and control. To suit their purposes and simplify their task of detection, they have labelled the minerals chrysotile, crocidolite, amosite, tremolite, anthoph-yllite and actinolite as asbestos, and any particle of these minerals with an aspect ratio of 3:1 as an asbestos fiber. It does not

Jan 1, 1976

By George R. Stephans

The Climax Mine is a panel caving mine which has had a long history of incidents of severe ground control problems. The nature of the ore deposit, which lends itself to the caving meth- of of production, a1 so makes the mine susceptible to large scale stress concentrations which are referred to as ?weight? problems. These problems have increased with increased production and also with expansion to deeper mine levels. During the past twenty years the mine has had to learn to cope with these problems in order to remain in operation. A number of practical guidelines and useful techniques have emerged from these efforts. The purpose of this paper is to share a few of these ideas. The Mine is located near Leadville, Colorado on the continental divide at an elevation of 3450 meters. The ore body is a large low grade deposit of disseminated molybdenum sulfide. It measures about 1200 to 1600 meters in diameter and it had an original depth of about 660 mters. The Mine has been in operation since 1918 and the massive nature of the ore body together with its blocky, highly fractured condition made it natural for the caving system to have been adopted for production at an early date. Open pit mining was started in 1973. The total plant has a capacity of more than 50 thousand tons per day, and more than 400 million tons of reserves at an average grade of 0.310 percent molybdenum disulfide remain to be produced.

Jan 1, 1982

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By J. B. Gwiazda

In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the .u factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the .u of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves.

Jan 1, 1987

By Sidney A. Hiscock

INTRODUCTION Lead and zinc are today rightly regarded as sister metals. Historically, however, they differ markedly with lead being known and in general use as the metal since 3000 BC in several countries which at that time might have been described as mature economies. Zinc was not isolated and recognised as an industrial metal with distinct and valuable properties until about 1700-1800 AD (although it had, of course, been utilised as a constituent of brass for some 2000 years previously). c were well established as industrial metals by the beginning of the 20th century. The present paper briefly reviews the overall growth in world consumption* and changes in the three main areas which today represent the mature economies or industrialised areas, i. e. ,Europe, the United States and Japan. Trends in overall consumption are determined by the demands for the individual uses for lead and zinc. The changes in patterns of use in the industrialised areas - individually and collectively - and reasons for the changes are also considered. LONG TERM TRENDS - 1900-1984 The World Picture Since the beginning of the 20th century the world consumption of lead (3.9 million tonnes in 1984) has grown almost fourfold and that of zinc (4.7 million tonnes in 1984) is almost eleven times greater than it was in 1900. The long-term trend has been one of continuing expansion for both. metals although the pattern has been severely disturbed at certain periods, for example in the years immediately following the two world wars and at times of marked recessions in industrialised areas. Apart from such major setbacks, new levels of consumption have been established regularly every few years. Recently, however, consumption has not really grown and with only a slow and partial recovery in world industrial activity at present, there is no indication that the peak consumptions of 4.2 million tonnes of lead, set in 1979, and 4.8 million tonnes of zinc (1973) will be exceeded in the near future. The growth in world lead and zinc consumption since 1900 is shown in Figure 1 (which includes changes in copper and aluminium for comparison). Overall growth over the period 1900-1984 has been about two percent a year for lead and about three percent for zinc (annual growth for copper has also been about three percent). Increases in tonnage consumption and growth rates by decade for lead and zinc are summarised in Table I. However, the growth rates by decade sometimes conceal very large individual annual increases and decreases. For example, in 1975 lead consumption fell by 13 percent and zinc consumption by 22 percent compared to 1974. In 1976 consumption of lead and zinc rose by 12 percent and 18 percent respectively. The years when consumption 'landmarks' (ie one, two, three and four million tonnes) were first reached are shown on Table 2. Clearly, the pattern of shorter periods being required to attain each extra million tonnes of consumption was broken in the 1970's. The consumption of zinc overtook that of lead for the first time in 1940, and since 1946 has always been at a higher level. Trends in industrialised areas The two key industrialised areas at the beginning of the 20th century were Europe and the United States which between them accounted for some 95 percent of world lead consumption and 98 percent of zinc consumption. Figures 2 and 3 show the growth in lead and zinc consumption, and Figures 4 and 5 the percentage shares for each area since 1900. Europe has usually been the major user of lead except for some years in the 1920fs, most of the 40's and early 50's when consumption in the United States was larger. In 1900, Europe accounted for about 64 percent of world lead consumption and the United States just over 30 percent. Currently, Europe takes about 40 percent of world consumption and the

Jan 1, 1986

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986