Search Documents

By Erik S. Bernard

"INTRODUCTION Conventional steel bar reinforcement is used in many tunnel linings to provide high flexural and tensile load resistance. These Reinforced Concrete (RC) tunnel linings may suffer flexural cracking during service or, in the case of precast concrete segments, during production, handling, or installation. Cracks can lead to corrosion of steel reinforcement, so limits are placed on maximum acceptable crack widths to reduce the likelihood of corrosion during the intended design life (AFTES, 2013; MC2010, 2012). However, the relatively light level of reinforcement used in many applications can result in quite wide in-service crack widths, so either additional steel bar reinforcement is required to limit maximum crack widths, or fibers can be included to control crack widths. Numerous investigations have been undertaken into the efficacy of including steel fibers to reduce crack widths in conventionally reinforced members (Stang and Aarre, 1992; Abrishami and Mitchell, 1997; Bischoff, 2003; Dupont and Vandevalle, 2003; and Jansson et al, 2010), but steel fibers suffer the problem that they are at least as sensitive to corrosion at cracks as steel bars and therefore have similarly tight limits placed on acceptable crack widths (AFTES, 2013). An alternative means of maintaining narrow crack limits in RC members has therefore been sought. The current investigation was instigated following an observation that theories promoted as an explanation for the ability of steel fibers to reduce crack widths in reinforced concrete flexural members (Deluce et al, 2014) do not depend on the material composition of the fibers used but instead depend primarily on the tensile stress generated by the fibers across cracks. Since it is known that macro-synthetic fibers are capable of equaling the post-crack tensile capacity of steel fibers, it has been hypothesized that macro-synthetic fibers are also capable of reducing crack widths in reinforced concrete flexural members but with the added advantage that macro-synthetic fibers are completely immune to the effects of corrosion. Use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete flexural members subject to aggressive environmental exposure is more rational than use of steel fibers because steel fibers are very sensitive to the corrosive effects of environmental exposure at cracks. The current investigation was therefore undertaken to explore the potential use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete members subject to flexure. Barchip BC54 fibers were selected as they are one of the most widely used and competitive high performance macro-synthetic fibers currently available."

Jan 1, 2016

By E. D. Sehnke

The refractory materials industry provides the largest commercial market for nonmetallurgical grade bauxite. Refractory grade bauxite is prepared from bauxites having low iron, titania, and alkali content by calcining at temperatures near 1,650° C. Although there are substantial bauxite reserves in the world, premium grade bauxite ores suitable for use in refractory applications are limited to only a few specific sources, primarily in Guyana and the People's Republic of China. Consumption of bauxite for refractory use is closely associated with the production and consumption of primary metals, in particular iron and steel. Barring major disruptions within the principal producer nations, sufficient supplies of refractory bauxite will be available to meet world demand well into the next century, and raw material costs will continue to determine the availability of markets for bauxite-based refractory products.

Jan 1, 1992

By M. Buxton

"Advanced data acquisition and process modelling technology provides online data and decision support about different aspects of the resource extraction process. Real-time approaches have recently been applied to utilize the value of this information for improved production control in mineral resource extraction in different operational set ups including coal, polymetallic ore and gold deposits. The key concept of these approaches promotes the change in paradigm from discontinuous intermittent process monitoring to a continuous process and quality management system in the resource extraction process. The framework includes a real-time feedback control loop that rapidly links online material characteristics data acquired during extraction at the mining face, during material handling and processing with a sequentially up-datable resource model. This will allow near real-time optimization of decisions related to long-term planning, short-term sequencing and production control. The contribution reviews recent developments in the three main constituents sensor based material characterisation, rapid updating of grade control models and simulation based optimization for improved production control. Technological readiness is assessed and critical gaps for further technology development are identified. The value added is illustrated by means of selected case studies. INTRODUCTION With the depletion of known and established mineral reserves, the decrease in head grades and the continuing demand of mineral raw materials by the modern society, future exploitation will move towards extraction of deposits under geologically more complex conditions. Complex deposits are characterized by a low continuity in grade, presence of deleterious elements such as arsenic and high irregularity in the geometry of the ore boundaries. The profitable exploitation of such deposits becomes significantly more challenging. To be able to better utilize such unconventional mineral resources of the future, smart autonomous mining systems are needed, which integrate local exploration of spatially varying material characteristics in–situ and have the ability to follow and extract the pay zones in the ore body while minimizing dilution (Buxton and Benndorf, 2013). The main barriers to overcome for the successful economic exploitation are: • effective grade control which will maximize resource potential along the whole value chain, • minimization of handling zero-value material introduced by dilution, thus • reducing unnecessary expenditure of energy and financial resources and • management and control of the geological uncertainty due to limited information available,"

Jan 1, 2017

By Miguel Angel Banuet Rodriquez, Hector Conceso Aragon

"Construction of the longest road tunnel in Mexico is part of Acapulco’s alternate roadway to the scenic roadway project. This article provides a brief summary regarding details of the construction since the project began. Work was done by skilled engineers and Mexican workers that includes outstanding execution of the work in an urban and tourist area. This project will have a strong impact on the steady development of the port of Acapulco.Project locationAcapulco’s Alternate Roadway Project is currently under construction in the city of Acapulco, located in the Guerrero state of Mexico. It is an 8-km (5-mile) long roadway that starts at the Icacos neighborhood, heading toward Acapulco’s airport, crossing a drill-and-blast tunnel that is 3,160 m (10,350 ft) long under Veladero Park, a mountainous area. The tunnel overburden reaches a depth of 380 m (1,250 ft) approximately at the central point of the horizontal alignment, and continues with a 4-km (2.5-mile) long elevated road to connect to the existing Viaducto Diamante toll road (Fig. 1).Tunnel construction has already been finished using two portals for drilling and blasting operations; Brisamar Portal on the west side and Cayaco Portal on the east side (Fig. 2).Geometric dataOnly two main excavation cross-sections were considered in the executive design. The first one corresponds to the running tunnel for a three-lane vehicle section, with crosssection areas between 120 and 130 m2 (1,290 and 1,400 sq ft) taking into consideration different geological and geotechnical conditions to be encountered (Fig. 3).The second one corresponds to eight emergency bays, each one 50 m (164 ft) long, laid down within the tunnel outline, located at 400 m (1,312 ft) from each one with excavation cross-sections between 156 to 169 m2 (1,680 to 1,820 sq ft), in accordance to geological and geotechnical conditions to be encountered (Fig. 4).The tunnel’s horizontal alignment is completely straight, having a small curve within the vertical alignment on Cayaco portal, because there were some differences in levels when tunnel excavation started. Tunnel slopes were designed in such a way that rainwater does not run down into the tunnel at any time."

Jan 3, 2018

By E. Maré

Some of the members will probably ask themselves what close relationship exists between hydro-metallurgy and a wet scrubber, but we are sure that as soon as deeper thought is given to the matter it will be realised how vital scrubbing, operations are in metallurgical plants. In ordinary metallurgical installations or pyro-metallurgical processes ore concentrates are first of all shifted from place to place and dust is created. In other cases the ores or concentrates are crushed or dried or roasted, and in each one of these operations dust and fumes, are created. All suspended particles and fumes originating from the abovementioned conditions not only, in many instances, provide health hazards which disrupt production and endanger the personnel in the plant, but also are the source of economic losses through extra maintenance and wear to moving machinery due to abrasion and corrosion. Further losses are incurred by the waste of fine, very often valuable, components. The Party who once said that in several metallurgical plants the bulk of the profits was discharged into the atmosphere by the stack wasn't stretching the truth. There is a place in Africa where a gold producing concern used to lose over 5 oz. of fine gold per day out of a total production of 3000 oz. per month. In another instance, copper concentrate going as high as 80% Cu was discharged into the atmosphere at the rate of 4 tons per day. Realising the value of removing and collecting solids and fumes created in metallurgical plants, a thorough study was made of the available plant and equipment offered on the market. Some units were found very efficient, but very expensive; some others also very efficient but with temperature and maintenance limitations. Some others were also efficient but prohibitive from the point of running costs.

Jan 1, 1963

By Alexander E. McHugh

A study of some variables affecting the recovery of molybdenum from oxidized molybdenum minerals was made. The effects of variations in contact time, temperature, pulp density, particle size, and solvent concentration on the recovery of molybdenum using acid and alkaline solvents were investigated. Chemical analyses, screen analyses and microscopic examinations were made and the presence of important elements determined. A hydrometallurgical method was developed to recover the molybdenum from the oxidized molybdenum ore by simultaneous dissolution of the molybdenum with sulfuric acid, adsorption on activated charcoal and flotation of the charcoal. The molybdenum was extracted from the activated charcoal with sodium hydroxide, precipitated with calcium hydroxide as calcium molybdate and this regenerated sodium hydroxide for additional stripping. A solvent extraction method, using mines, was also studied to recover molybdenum from both alkaline and acid molybdenum solutions. Satisfactory results were obtained.

Jan 1, 1967

By N. A. Abdel-Khalek

An experimental study was carried out to compare the results of laboratory column flotation versus conventional flotation for the cleaning of fine coals of different rank and their oxidized samples as well as discrete size fractions. Surface oxidation caused a significant reduction in the flotation yields achieved with both methods. However, the column flotation produced concentrates? of lower ash content. The recovery -size curve achieved with column was similar in shape to that obtained with conventional cell, with superior results in the region of fine fractions. The influence of some column operating parameters was also discussed.

Jan 1, 1990

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By D. Diekman

Perlite is not a trade name but a generic term for naturally occurring siliceous volcanic rock. A distinguishing feature which sets perlite apart from other volcanic glasses is that when heated to a suitable point in its softening range, it expands 5 to 20 times its original volume. This expansion is due to the presence of 2% to 6% combined water in the crude perlite rock. When quickly heated above 1600°F (871°C) crude perlite pops in a manner similar to popcorn. The combined water vaporizes and creates countless tiny bubbles in the heat softened glassy particles. It is these tiny glass sealed bubbles which account for the amazing lightweight and other exceptional physical properties of expanded perlite. The bulk densities of the expanded perlite generally range from 3 pounds per cubic foot (48 Kg M3) to 10 pounds per cubic foot (160 Kg H3).

Jan 1, 1985

By Everett H. Dobbs

The Tripoli deposits in the southwest corner of Missouri In Newton County and the northeast corner of Oklahoma in Ottawa County, located in the vicinity of Seneca, Missouri, contains an unusual and peculiar form of silica which has not been found any other place in the world. Its outstanding characteristic is the physical structure of the individual particle, The particle structure of the Missouri-Oklahoma type Tripoli accounts for its market. It is a soft, friable, porous, double-refracting silica of the chalcedony variety, The particle is porous, has a fibrous structure, no sharp edges or comers, ad an average size of less than .01 millimeter, It varies from 90 to 98 per cent Si02 with less than 1 per cent free silica in the form of quartz, 24; has ignition loss of 1 per cent and fractional percentages of iron, alumina, lime, etc.

Jan 1, 1960

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By V. R. Voller

The WTBAL computer program for evaluating material balances for minerals processing flowsheets was developed at the MRC and has been in general use for a number of years. This paper reports on two enhancements to the basic MTBAL routine. The original program accounted for errors in the process measurements and used estimates of measurement variability to calculate stream weights. Unfortunately, the estimate of measurement variability was fixed over all streams. In the enhanced version of MATBAL, named IMTBL, the program equations and their solution procedure have been modified to allow the estimated variability in a process measurement to vary from stream to stream. The .second enhancement involves making MTBAL interactive. As such, the user now prescribes his information in an easy-to-use fashion in a conversational mode via a terminal. Finally, an assessment of the feasibility of implementing IMTBL on microcomputer systems will also be reported.

Jan 1, 1982

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988

By F. W. Mueller

It seems to be a matter of general understnading that title extraction or use of ground water may not be used as the basis of a depletion deduction under the United States Revenue Code And indeed, I have been unable to find any precedent upon which to base such a deduction. It is for this reason that the Shurbet case, which is the subject of my discussion and is now before the Court, may well become a precedent as authority for the allowance or disallowance of a depletion deduction for income purposes. It is well known that the law recognized that capital is consumed in the process of extracting minerals, oil and has, other natural deposits, and timber (underscoring supplied). This exhaustion, or depletion, is likened to the using up of raw materials in manufacturing. The law, therefore, provides a deduction for depletion which is intended as compensation for the exhaustion of assets consumed in the production of income through severance of minerals, oil and gas, other natural deposits, and timber.

Jan 1, 1962

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By J. B. Mitchell

Comminution methods for base metal and precious metal ores have had considerable attention from mine operators, equipment suppliers and design engineers for many years and much of their work has been well reported. This interest derives from a healthy concern with the costs of comminution, often the largest single cost factor in ore dressing of hard ores. Many imaginative innovations have resulted. One notices a trend toward autogenous and semi-autogenous methods, combined with a trend toward very large equipment. Unfortunately, there has been less obvious cost incentive to experiment with softer ores. This is unfortunate because the consequences of inappropriate comminution methods can have an important effect on overall economics by influencing down stream processing and salability of final products. This paper concerns some of the factors to be considered in the selection of comminution methods for potash ores, and gives some specific examples to illustrate some of the principles involved.

Jan 1, 1969

By José A. Matar Ibañez

Geologic terranes in Argentina include potential mineralized environments from localized younger Precambrian cratonic outcrops through Paleozoic sequences, generally in the northwest or under younger cover, to the Mes[o] zoic-Cenozoic Andean Systems in western and southern Argentina. Argentina is self sufficient or nearly so in many metallic, nonmetallic, and energy commodities, and exploration in each of these categories is ongoing. Present production of precious metals (silver and gold) is important, and many recent discoveries of base metals, precious metals, alloy metals, and other mineral categories have been made. Economic trends, geologic environments, and commodity types important in actual exploration are described, and it is emphasized that extensive areas showing attractive alteration, geochemical, and geological anomalies, especially of porphyry, cordilleran vein, and epithermal characteristics, remain to be fully evaluated.

Jan 1, 1986