Search Documents

By G. Barbery

In Mineral Processing, the objective of most processes is the separation of mixtures of minerals, which are originally associated in composite particles. Feed preparation processes grinding for instance, which take place before beneficiation or separation processes do not usually break particles at the boundary between mineral phases. They produce composite ("middlings") as well as liberated particle. It is therefore necessary, in a particulate system, to determine the proportion of particles which are liberated as well as, ideally, the size distribution of minerals which remain associated in composite particles. Up to now, there has been a lack of experimental techniques to characterize completely composite particulate systems. Heavy liquid separation which is commonly used to obtain information of this type can only be applied to simple binary cases for which one mineral has a low density (lower than e.g 2.8 ). The technique which is proposed in this paper involves the measurement of parameters on polished sections of particles mounted in a matrix, and the use of mathematical transformations to reconstruct in three-dimensions the information obtained from these measurements .

Jan 1, 1977

By Terence P. McNulty

Gold-bearing outcrops were discovered in 1862 by Union soldiers garrisoned at Needles, CA, near the northwest corner of the future State of Arizona. Sporadic mining began several years later, but engineered shaft sinking and mill construction were not adopted at Oatman and the neighboring camp of Goldroad until about 1900. Geological interpretations in 1915 enabled major production during the next decade. In the late-1930s, USSR&M built a new mine and mill in Gold Road and the District flourished until closure by Federal Order L-208 in October 1942. For about a decade, Oatman’s mines were among the largest gold producers in the American West.

Feb 1, 2024

By Francisco J. Sotillo

Using new ecological-natural-organic depressant for gangue and pyrite with antibacterial properties (control of acid mine drainage) with new improved xanthate collectors using rheology additive not chemical reacting with xanthate resulted in better sulfide flotation. Rougher-scavenger lead flotation tests were conducted increasing the concentrate grade from 7.07% Pb to 13.44% Pb, enhancing selectivity. Lead recovery increased from 64.08% to 79.38% and 80.40% using only the new depressant, and improved xanthate Z-11 and Z-4, respectively. The results demonstrated that the new depressant was selective and efficient, and the new improved xanthates stronger more selective collectors.

Feb 22, 2026

By Dean Brox

Tunnel boring machines (TBMs) have been used for the construction of various tunnels for mining projects for the purpose of access, conveyance of ore and waste, drainage, exploration, water supply and water diversion. Several mining projects have seen the successful and economic beneficial use of TBMs, and there is an increasing awareness of the benefits of TBMs for mining projects. Key technical considerations for the use of TBMs for the construction of tunnels for mining projects include geological issues (rock type, rock alteration, rock strength, rock abrasivity, durability, ground water in flows), depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, TBM constraints, minimum tunnel size, tunnel support requirements, contractor and labor experience, and project schedule demands. TBMs offer key project schedule benefits with high rates of progress, which is a unique economic advantage recognized for mining projects where timing is of the essence in order to advance mining development and achieve early startup for operations. A thorough evaluation of the anticipated ground conditions should be performed as part of the decision to adopt a TBM for a mining project. Minimum specifications for TBMs are necessary in order to prevent the incorrect type of TBM from being used. Appropriate geotechnical investigations are necessary in order to provide key information on the anticipated subsurface conditions for careful planning and design of the proposed tunnel alignment. The overall site and geological conditions associated with some projects may suggest that it is not appropriate to use TBMs for some mining projects due to a perceived higher risk. Key words: TBM, Tunnel boring machines, Tunneling in mining

Feb 1, 2014

By M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material build-up inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 mtpd and significant operating costs savings.

Jan 1, 1985

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983

By William A. Riggs

Salt, a non-metallic mineral whose use dates back to earliest history of mankind, and whose uses cover the widest range for any mineral raw material, is generally of widespread occurrence in commercially recoverable quantities in the oceans, in certain sedimentary rocks, in certain lakes, and in certain underground waters. Passing over geological detail, it may be said that, generally, all of the salt in the world has, at least once in geological history, been in solution in the oceans. The total salt content of today's oceans, said to equal 4.5 million cubic miles of rock salt, dwarfs the tremendous volume of salt in the sedimentary rocks. In 1958, United States production of salt was about 22 million net tons and world production about 82 million. About 3 percent of United States production is table salt, with chemical, municipal, industrial and agricultural uses taking the remainder. Mississippi River. Figure 1 has been expanded sufficiently to show also those salt occurrences and producing points which might economically ship salt into these states. Although widespread in occurrence, salt deposits and possible production areas generally show very sharp local boundaries. Salt-for non-table use is susceptible to ?place value?, a common problem in low valued raw materials, where transportation costs often exceed the value of the material f.o.b. the production point. Generally only large capacity mechanized salt producing operations can compete in United States markets, as contrasted to the many small local salt evaporators in less industrialized Mexico.

Jan 1, 1962

By M. S. Tsai

Recovery of uranium from wet-process phosphoric acid is a newly developed source of uranium. Many processes have been developed but the OPAP (octylphenyl acid phosphate) process is still the valuable one because the OPAP reagent compound has the high extraction ,power and cheap cost. The OPAP process was already studied by murthy(1) in 1970 and its complete process flow sheet was first fulfilled by F.T. Hurst(2) in 1974. WCFC(3) (western Co-op Fertilizer Ltd.) in cooperation with ESI (Earth Science Inc.) set up the OPAP uranium recovery pilot plant in Canada in 1978. We have studied the OPAP process since 1974 and first improved the OPAP extractant by proper adjustment of the DOPAP/MOPAP mole ratio with CH3OH-H20 method, resulting in shortening the phase separation time and avoiding the precipitation occurrence in our process. Second, we utilize the reduction and oxidation occurring by DC power supply on either side of the membrane to achieve the extraction and stripping at the same time. An improved OPAP process in which high recovery yield of uranium and acid uncontaminated by iron has been developed in our laboratory.

Jan 1, 1982

By XUEWEN WANG, Changda Zhang, Huaguang Wang, Mingyu Wang, Bin Hu

The copper smelting process produces plenty of copper slag every year, which is a hazardous solid waste, but a secondary resource. In the present study, the extraction of copper, nickel, and cobalt from copper slag was investigated through the process of sulfation roasting–water leaching and the process of sulfation roasting–sulfate decomposition roasting–water leaching respectively. Compared with the process of sulfation roasting–water leaching, the process of sulfation roasting–sulfate decomposition roasting–water leaching is a better choice, which could not only get almost the same leaching of copper, nickel, and cobalt as the former process, but has a lower leaching of iron and aluminum. For the process of sulfation roasting–sulfate decomposition roasting–water leaching, the leaching of Cu, Ni, and Co reached up to 74.2%, 71.1%, and 69.6% respectively, under the optimal conditions including sulfation roasted with 80 wt% sulfuric acid addition at 200 °C for 60 min and sulfate decomposition roasted at 650 °C for 60 min, followed by water leached at 90 °C for 30min with a liquid–solid ratio of 2 ml/g. The leaching of Fe and Al was only 4.9% and 17.6%.

May 4, 2020

By Dean Brox

Tunnel boring machines (TBMs) have been used for the construction of various tunnels for mining projects for the purpose of access, conveyance of ore and waste, drainage, exploration, water supply and water diversion. Several mining projects have seen the successful and economic beneficial use of TBMs, and there is an increasing awareness of the benefits of TBMs for mining projects. Key technical considerations for the use of TBMs for the construction of tunnels for mining projects include geological issues (rock type, rock alteration, rock strength, rock abrasivity, durability, ground water inflows), depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, TBM constraints, minimum tunnel size, tunnel support requirements, contractor and labor experience, and project schedule demands. TBMs offer key project schedule benefits with high rates of progress, which is a unique economic advantage recognized for mining projects where timing is of the essence in order to advance mining development and achieve early startup for operations. A thorough evaluation of the anticipated ground conditions should be performed as part of the decision to adopt a TBM for a mining project. Minimum specifications for TBMs are necessary in order to prevent the incorrect type of TBM from being used. Appropriate geotechnical investigations are necessary in order to provide key information on the anticipated subsurface conditions for careful planning and design of the proposed tunnel alignment. The overall site and geological conditions associated with some projects may suggest that it is not appropriate to use TBMs for some mining projects due to a perceived higher risk.

Jan 1, 2013

By Xiaojie Yang, Gang Yang, Zhenli Hao, Manchao He, Ruifeng Huang, Zheng Wang, Chaowen Hu

Preventing the spontaneous combustion of remnant coal, which is indicated by carbon monoxide (CO), is a significant issue for coal mining safety. The N00 longwall mining method with Z-type ventilation is advantageous for the prevention and control of CO; however, research regarding this topic is limited. To investigate the distribution of CO in a goaf and working face, a sealing material and technique for blocking the goaf were introduced after proposing a forming method for a Z-type ventilation system; furthermore, a monitoring method was designed and applied in the field. The results demonstrated that the CO concentration during mining in the upper corner and return airway ranged between 4–6 ppm and 3–7 ppm, respectively. More importantly, no CO was generated in the goaf. The results indicate that the advantages and mechanisms regarding the prevention of spontaneous ignition using the N00 longwall mining method with Z-type ventilation are as follows: (1) The adoption of the downward ventilation technique is not only beneficial for reducing the air pressure difference between both ends of the working face, but also prevents CO accumulation in the upper corner. (2) The basis of a spontaneous combustion disaster is eliminated owing to the absence of coal pillars reserved in the goaf. This study proposes a superior method for mitigating spontaneous combustion disasters related to remnant coal in the goaf in a coal mining field and contributes to the better understanding of the N00 longwall mining method for coal mining safety.

Nov 28, 2022

By Calvin L. Stevenson

The probability of a particle passing through a maze is predictable and consistent. This principle may be utilized to effect a particle size separation of materials by presenting a physical maze to a stream of material that will allow the fine particles to pass, while deflecting the coarse particles. A maze is effective even though all apertures encountered are many times larger than the particles being separated. By designing a machine that allows the probability parameters to be controlled and varied without changing physical dimensions, probability sizing becomes a useful tool for the separation of granular materials.

Jan 1, 1967

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By Hamed Khodadadi, Hamid Ghadiri

In this study, a fuzzy logic self-tuning PID controller based on an improved disturbance observer is designed for control of the ball mill grinding circuit. The ball mill grinding circuit has vast applications in the mining, metallurgy, chemistry, pharmacy, and research laboratories; however, this system has some challenges. The grinding circuit is a multivariable system in which the high interaction between loops, the variation of the system parameters with time, and time delay are some of the problems that pose a challenge. Since the controller parameters are determined offline in classic PID control, these gains are unchangeable and cannot overcome the mentioned challenges in this system. Hence, a fuzzy logic self-tuning PID controller, which is a combination of fuzzy logic and a conventional PID controller, is proposed to control the grinding system, especially in the presence of model mismatch and disturbances. In addition, in order to solve the system challenges, a multivariable control approach based on an improved disturbance observer is proposed to suppress the effects of the disturbances. The most important feature of the algorithm proposed in this paper as the combination of fuzzy logic self-tuning PID and improved disturbance observer is its ability to eliminate system interaction, attenuate internal and external disturbances, and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit. Simulation results in the cases of the set-point change in particle size and circulating load in the presence of model mismatch and external disturbances confirmed the controller performance compared to other controllers.

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Amilton Barbosa Botelho Junior

A new step in the Bayer process has been used to recover NaOH and to reduce its content in red mud. After digestion, the residue is separated from the Bayer liquor and goes through press filters, which enables the recovery of NaOH and decreases the moisture content. It is well known that red mud is one of the most important sources of scandium. For this reason, the goal of this work was to characterize a Brazilian red mud (BRM) for scandium recovery. The sample was collected after the press filter system process. Analysis of energy-dispersive X-ray fluorescence (EDXRF), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), and X-ray diffraction (XRD) was performed. Microwave digestion using an acid mixture was carried out to determine the concentration of the main elements. Fe2O3 represented 40% of the BRM, and the Sc concentration was 43 mg/kg. The SiO2 content was 24%, which is the highest value found in the literature, whereas the sodium concentration was the lowest. A literature review was carried out to compare results with BRM, as well as the current studies for recovery of scandium by the leaching/ion-exchange process. Scandium recovery using a leaching/ion exchange process may be possible with efficiency higher than 90%. The greatest challenge is the occurrence of silica gel formation during leaching.

Oct 19, 2020

By J. F. Childs

Montana consists of an Archean crystalline basement overlain by Proterozoic through Cenozoic sedimentary rocks. Igneous rocks range in age from Archean to Pleistocene; the most voluminous magmatism and volcanism occurred during the Late Cretaceous and early Tertiary. The state can be divided into three tectonic provinces whose deformational styles are a function of different bedrock responses to Late Cretaceous-early Eocene compressional tectonism. Several long-lived structural zones have been periodically reactivated since the Precambrian, and were the sites of recurrent magmatism. Regional gold distributions are strongly influenced by the tectonic provinces and structural zones. Lode gold systems in Montana occur in diverse geologic settings resulting from a complex interaction between structure, magmatism, and sedimentary depositional processes. Reserves or resources are known for 19 significant lode gold systems, and additional unannounced discoveries have been made recently. Mineralization ranges in age from Archean to Tertiary. The influence of long-lived structures is apparent at both the regional and deposit scale, and in some cases multiple mineralizing events have been superimposed upon one another. Most Montana gold systems have a direct spatial and genetic association with Late Cretaceous through Oligocene igneous rocks. However, the importance of sedimentary rocks and associated depositional processes should not be underestimated.

Jan 1, 1993

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By S. D. Irons

With the passage of recent national and state legislation aimed at tighter regulation of air pollution and smoke control, attention has been focused on a problem which has long confronted the coal industry--the disposal of coal waste with its inadvertent ignition. Even as recent as 1935, a decision from the Allegheny County Court of Common Pleas confirms the stand taken on control of burning coal refuse disposal areas. "The uncontroverted testimony is that there is no feasible method of operating a coal mine without a gob pile on the surface, as no use has ever been found for this troublesome by-product of mining; that every large coal mine has a large gob pile close to its tipple; that sooner or later these piles all ignite through spontaneous combustion; that practically every large mine in Western Pennsylvania has a burning gob pile, and that there is no known means of averting such a fire." 19* As a result of the past "no regulation policy," there are presently on the order of 500 burning refuse banks, of which 213, 142, and 49 are found in West Virginia, Pennsylvania, and Kentucky, respective¬ly. 18 Many of these refuse banks have burned for 40 years or more; many others may continue burning for a like period. It is estimated that the annual emission from these smoldering piles approaches 183,000 tons of pollutents which may produce many deleterious effects on the populace, property and vegetation in the proximity to the sources.16 To date, little progress has been made in alleviating the pollution from the currently burning refuse banks; however, numerous investigators who are researching the causes of ignition, as well as preventative disposal techniques (refuse compaction, layering and crushing to finer sizes) have met with some success in handling the newly discarded coal refuse.

Jan 1, 1967

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022

By Alexander N. Winchell

"Location. The iron formation of the Gogebic district (including the Penokee) comprises a narrow belt south of the western part of Lake Superior extending from Michigan for a considerable distance into Wisconsin. From the mouth of the Montreal River (about twenty-five miles west of Ashland) the iron formation is only about twelve miles distant, but it is about twenty miles south of Ashland. Beginning on the east at a point about eight miles east of Wakefield, Mich., it extends through Sunday Lake, Bessemer and Ironwood in Michigan, and thence south of west through Hurley, Wis., and only a short distance south of Mellen, Wis. About eight miles westward from Mellen, the formation disappears, but six miles further west it is known to reappear and continue thence for about eight miles. The total length of the range is about sixty miles, two-thirds of this distance being in the State of Wisconsin; but nearly all of the ore has been obtained from the eastern third of the district, which is in the State of Michigan.History. This iron range was first noted in 1848 by Dr. Randall, assistant geologist to Dr. David Dale Owen, while following the fourth principal meridian northward. It was also reported by Charles Whittlesey in an account of a survey made in 1849, and published by Owen in 1852. Analyses of the iron ore are given with the following account. ""The bed of magnetic iron ore south of Lac des Anglais is of extraordinary thickness,25 to 60 feet. * * In the wild and deep ravines where the Bad River breaks through the range, there is a cliff of slaty ore * * * probably three hundred feet thick. * * * I estimate more than one-half of this face to be ore, and in places the beds are from ten to twelve feet in thickness, with very little inter-mixture of quartz * * * . The position of the best exposures of ore which I saw is such as to require from eighteen to twenty eight miles of transportation to reach the lake."""

Jan 1, 1920