Search Documents

By Jason Swartz, Gerardo Gomez, Henry Leighton

San Antonio has experienced sustained growth for decades, putting increased pressure on existing wastewater infrastructure. In June 2013, San Antonio Water System (SAWS) reached a Consent Decree agreement that requires significant improvements to the wastewater system over a 10-year period to reduce Sanitary Sewer Overflows. One of the critical projects was the W-6 Upper Segment Tunnel project to reduce sanitary sewer overflows on an existing sewer main running through Lackland Airforce Base. The replacement project consisted of a new tunnel nearly 29,000 LF of primarily 104" FRP. The project also includes nine shafts and multiple trenchless crossings to make near surface connections to the new works.

Jun 23, 2024

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By Jr. Cook

Panned stream-sediment,geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial gravels of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa counties, Alabama, and Baldwin and Hancock counties, Georgia. Identification of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1988

By R. L. Grayson, J. R. Warneke

Environmental conflict between the public and private sectors, including mining, is highly visible and often based on deeply divergent environmental, social, and economic values. In order to achieve sound public policies by government, scientifically rigorous and objective analyses of mining’s impacts are demanded. Material flows accounting and analysis, linked with other data to generate indicators of environmental, social, and economic impacts of mining activity are means toward providing cogent input into public policy-making on key issues. This paper will present a material flows analysis scheme for the coal industry and recommend derived, objective indicators of coal mining’s impact on society.

Jan 1, 2004

By R. J. Wesely, A. D. Zunkel, Tracy B. Braun, Philip L. LeHoux

An overview of gold processing operations at Barneys Canyon Mine is presented with particular emphasis on ore agglomerating experience, leaching and metallurgical accounting practices, and carbon column plant operating approach. The mine, located thirty kilometers from downtown Salt Lake City, is just eight kilometers north of the Bingham Canyon copper mine. Mining was initiated in February 1989 and the first gold was poured in September 1989. Through year-end 1992, approximately 7 million tonnes of ore have been processed and 12,000 kg of gold have been produced. Gold recovery is in excess of 85 percent.

Jan 1, 1993

By J. A. Nelen, R. B. Cook

Panned stream-sediment, geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial sediments of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa Counties, AL, and Baldwin and Hancock Counties, GA. Identification and interpretation of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1990

By William C. Beebe, Russell E. Martin

An account of driving and concreting two 900 m railroad tunnels for the Denver and Rio Grande Western Railroad under emergency conditions. Details the importance of on-site decision making by the Owner in completing the project successfully in record time. A general description of the geology and construction methods. The Thistle Drainage Tunnel drained water impounded behind the Thistle slide and serves as permanent diversion of the Spanish Fork River and Thistle Creek around the slide area. The project involved 684 meters of 5 m horseshoe tunnel, a 5 m diameter raised shaft and 23,000 cm of cut excavation.

Jan 1, 1985

By D. Shink

A small scale continuous flotation cell was designed and constructed at Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine. This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results.

Jan 1, 1992

By C. Zhou, J. Srednicki

Electronic systems have been increasingly used in underground mines to improve mine safety. These electronic systems emit electromagnetic (EM) energy which can adversely impact the performance of other electronic systems nearby and thus should be characterized. Researchers at the National Institute for Occupational Safety and Health (NIOSH) characterized the magnetic fields emitted from devices that can potentially interfere with the performance of proximity detection systems (PDSs) and compared the emission levels of these devices to the susceptibility of PDSs. In this paper, we present our measurement results pertaining to this effort. Particularly, magnetic fields emitted from the different orientations of a powered air purifying respirator (PAPR) and two lite trackers are evaluated based on the RE101 protocol specified in the MIL-STD-461G standard. The results show that both devices emit strong magnetic fields which strongly depend on the orientation of the devices. At some frequencies, the maximum emission levels from the two devices exceed both the emission limit given in MIL-STD-461G and the maximum magnetic fields that a PDS can withstand without a failure. The results and findings in this paper can help the mining industry better understand electromagnetic interference (EMI) underground and provide critical scientific data that support mining-specific recommendations to address EMI-related challenges.

Feb 1, 2023

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978

By V. Herman, B. Knorr, D. Whalen

"Edge effect is a condition widely observed in High Pressure Grinding Roll (HPGR) operations that gives rise to reduced comminution at the edges of the roll surfaces. This effect is caused by a reduction in the local crushing pressure at the edges of the rolls resulting from the sliding friction between the static cheek plates and HPGR feed material. Practically, this has an impact on equipment sizing, as the edge effect leads to coarser particles reporting to downstream equipment in open-circuit operations and increased circulating load and diminished HPGR circuit capacity in closed-circuit operations.To address this, Metso's HRC™ HPGR incorporates an Arch-frame to maintain a parallel relationship between the rolls and allow for the use of a flanged roll design. We conducted a series of pilot-plant tests with a 750 mm by 400 mm HRC HPGR to compare the performance of the flanged roll design against that of a traditional cheek plate arrangement under similar operating conditions. The edge effect was found to be significantly reduced with the flanged roll design. Based on the pilot-plant results, the implications for circuit design, energy efficiency and overall plant performance in a full-scale application were investigated and discussed.IntroductionGlobal trends such as lower ore grades and rising operating costs are driving the market toward more energy-efficient mineral processing solutions, most notably in comminution circuit design. High pressure grinding rolls (HPGRs) have been recognized as an energy-efficient solution relative to more conventional circuit designs. The basic operating principle of HPGRs, in which a fairly uniform pressure is applied to a bed of material in the compression zone, lends itself to this improved energy efficiency (Morley, 2006). Studies have estimated that savings of 10-15 percent are possible when comparing an HPGR circuit with a traditional SABC circuit (Rosario and Hall, 2008). While HPGRs offer a more energy-efficient solution than tumbling mills, there is still room for improvement in many aspects of the design. Edge effect, in particular, is one such aspect that limits the effectiveness of the machines. Edge effect is the impaired performance at the edge of the rolls due to a reduction in crushing pressure (Morley, 2010; van der Meer, 2010). As described in our prior work (Knorr, Herman and Whalen, 2013), edge effect is caused by the interaction between the ore entering the crusher and the relatively static cheek plates positioned at the edges of the rolls. As the material is drawn into the crushing zone, the sliding friction between the ore and the cheek plates inhibits the ability of material to be effectively drawn into the compression zone at the edges of the rolls. This reduces the crushing force in those edge regions relative to the center of the roll where material is being drawn into the compression zone at a higher rate. In addition, the cheek plates of a traditional HPGR design are held in place by spring-loaded brackets that are adjustable to manage the clearance. This spring-loaded cheek plate design prevents full compression of the material in the edge regions of the roll as there is relief at the outer edges."

Jan 1, 2016

By E. -R. Niinikoski, M. A. Islam, H. Mischo, G. Barakos, J. Joutsenvaara, G. Meissner

European Union's transition to a low-carbon and digital economy highly depends on securing the strategic autonomy of the Critical Raw Materials (CRMs) supply chain. This paper introduces a European Commission-funded research and innovation action, AGEMERA, which aims to create detailed geological and people's concerns maps to unlock the CRMs potential in Europe. Furthermore, the project will develop educational packages for schools and universities, publish online CRM-related games and news flashes, and arrange public events to ensure a basis for socially accepted and sustainable exploration and mining of CRMs in Europe. 1. IntroductionCritical Raw Materials (CRMs), crucial for shifting to a low-carbon and digital economy, should focus on maintaining Europe's overall supply-demand balance (Birol, 2022). Therefore, to proactively address the surge in demand and ensure the strategic autonomy of European industrial supply chains, the exploration and extraction of CRMs must be scaled out across the continent. Moreover, mobilizing Europe's domestic potential is vital for the EU to become more resilient and to establish open strategic autonomy as the demand for CRMs continues to increase quickly on a global scale (European Commission, 2021). Base metal extraction and mining have a long history in Europe. Nevertheless, CRMs mining projects have shown less success, although these have a lot of potential (Guzik et al., 2021). The main barriers are a lack of investment in mining and exploration, complicated and drawn-out national permitting processes, and low levels of public support (European Commission, 2020). It is necessary to have a vast amount of knowledge and intelligence about CRM's potential and market impact. Novel non-invasive geophysical survey techniques that enable sustainable exploration must be created and used to enhance mineral system models of ore deposits incorporating CRMs. The minerals policy framework significantly influences the mining industry's performance, stability, and sustainability. However, the EU Member States' mineral policy frameworks differ significantly (MINLEX, 2017). In addition, the Fraser Institute Annual Survey of Mining Companies offers concrete information on how managers and executives of mining companies view key policy areas that impact mining activities in the jurisdiction in which they operate or are familiar (Jackson & Green, 2015).

Feb 1, 2023

By Robert B. Tippin

A number of recent studies 1-4 suggest that steelmaking expansion might be achieved more economically by a combination of the prereduction furnace and the electric steelmaking furnace rather than through new blast furnace construction. Supergrade concentrates would be the first step in an evolving technology which bypasses the blast furnace and in which the concentrates are first made into pre¬reduced pellets and then used directly in electric steelmaking, Prereduced pellets made from superconcentrates should not only be competitive with scrap, but should be a preferred feed for the electric furnace because of the absence of such residual elements as copper and nickel. Furthermore, geographic areas remote from present steelmaking centers may find the electric furnace to be an economical method of providing local steel requirements. The development of successful methods of producing superconcentrates may also be expected to find application to conventional blast furnace burdens. The need for methods of increasing grade of domestic concentrates will become increasingly urgent in the face of competition from high grade imports. Only a small percentage of domestic iron ore production can qualify as superconcentrates, (Superconcentrates for the purpose of this investigation are limi¬ted to those concentrates which contain a maximum of 2 percent S'02). During the last several years the Twin Cities Metallurgy Research Center of the Bureau of Mines has directed research efforts to develop methods of manufacturing superconcentrates from present standard grade products by cationic flotation, screening, and magnetic separation.

Jan 1, 1971

By F. L. Jackson

When using perlite as an insulation, it is important to determine the requirements for different applications as this influences the processing of the perlite. In cryogenic applications, perlite properties of low density and fine particle size are desirable, while Loose fill insulation applications require similar properties and water repellency. However, in perlite insulating concrete applications, a coarser particle, of higher density, is required to provide improved compression strength. The essential properties of perlite including, particle size, density and surface treatment are discussed in relation to the various insulation applications. Also typical mineral processing and manufacturing techniques are reviewed

Jan 1, 1983

By G. T. Lineberry

Reduced clearance is one of the most important characteristics of encumbered space in underground coal mining. Another key variable is the maximum velocity at which a piece of mobile mining equipment can operate in this limited space. Typical velocity- clearance curves for different mine transportation systems are developed and characterized. Applications of the relationships are examined, emphasizing their significance in the design and control of mine materials handling systems.

Jan 1, 1983

By A. T. Yu

The quest for ore in an open pit is fundamentally an earth moving proposition. This thesis is vividly underscored by the rapidly increasing volume of waste to be removed in newer mines, where in some instances waste to ore ratios have reached as high as 20 to 1. Continuing depletion of high grade reserves, greater demand for raw materials, coupled with ever climbing labor costs, have made the problem still more pronounced and the need for more effective means of earth moving in an open pit even more acute. A conservative approach to the problem has been to upgrade the sizes of conventional earth moving equipment such as shovels and trucks. In many open pits, particularly in the C.S., this has been responsible for the generally down- ward trend of earth moving costs. None the less, the investment costs of these machines are high, and their gigantic engines are seldom fully utilized. Moreover, a large number of operators are required and maintenance remains relatively high. Unfortunately most people have felt that no other viable alternative was in sight within today's technological capabilities.

Jan 1, 1973

By Alen Shibu Joseph, Arvind Rajnarayan Singh, Mudila Dhanunjaya Rao, Kamalesh K. Singh

In this article, the cementation of major impurities from zinc sulphate leach solution by the addition of zinc dust was studied by considering different parameters including time, mesh size, and percentage of excess zinc dust. The output obtained from various experiments was utilized for the design of experiments. A multi-level categorical factorial design with a quadratic model was employed during this study. Results were predicted to minimize the concentration of impurity metals in the solution by altering the parameters. Furthermore, these predicted results were validated by performing another experiment. Successfully, it showed that the predicted and experimental data values were close to each other. The predicted optimized values were 40 min, 100% excess zinc dust, and 300 mesh size for copper; 42 min, 100% excess zinc dust, and 300 mesh size for cobalt; 37 min, 100% excess zinc dust, and 300 mesh size for cadmium; and 34 min, 100% excess zinc dust, and 300 mesh size zinc dust for nickel. At these optimized values, the experimental results showed 99.99%, 55.7%, 99.6%, and 76.6% cementation efficiencies for copper, cobalt, cadmium, and nickel respectively. The statistical design of experiments for the effective cementation of impurities corroborates the economic feasibility of optimizing parameters for the proposed process.

Jul 18, 2022

By Paul Wellman

The energy problem of the U. S; was emphasized by the oil embargo of late 1973 and early 1974 and it seemed for a time that the Federal Government, under pressure from the general public, might take some corrective action. However, this was not the case. With the gasoline lines gone and an apparent plentiful supply of petroleum products, public concern quickly dissipated., This country is more vulnerable to an oil embargo today than we were in 1973-1974 and this fact should be of concern to all our people. Since 1968, we have used oil and natural gas at a much more rapid rate than we have been able to find new domestic sources; thus, there is an increasing gap between domestic production and consumption and we have filled the gap with ever increasing oil' imports. These imports have increased at an alarming rate in the recent past, some 58 percent in 1976 compared with 1975. Imports are nearing 8 million barrels per day. Then, by applying some simple arithmetic, at $12 per barrel, the resulting trade deficit is $96 million per day or $35 billion per year. Obviously, this cannot be tolerated by our economy over a long period of time. Historically, we have shifted from one fuel to another as is shown in this slide. In 1850 about 90 percent of our fuel requirements came from direct combustion of wood, by 1900 we shifted to coal for 70 percent of our fuel, and now about 78 percent of fuel requirements comes from oil and natural gas. The difference is that the previous shifts were voluntary and the one facing us now is of necessity.

Jan 1, 1977

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978