Search Documents

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

By C. R. Tinsley

Valuations can be molded, twisted and misinterpreted. Cases of spurious scope setting; limits to the information or access by the valuer; difficulties with the lack of comparative valuations; inappropriate valuation methods and outright speculations are described. None should be accepted by an experienced, independent minerals valuer. The Australasian Institute of Mining and Metallurgy (TheAusIMM) is working on a Valmin Code for which a Manual of Best Practice and Valuation Guidelines may be developed.

Jan 1, 1995

By Richard Klimpel

A common problem in mineral processing and chemical engineering is the need to estimate flow rates and/or weight ratios involved with engineering operations for which it is inherently difficult to directly measure stream weights. Simple examples of this situation include stream separators (a classifier operating on a particle flow) and stream mixers (the mixing of new feed and circulating load in a ball mill circuit). Often in these types of operations, it is possible to sample the streams involved to get approximate component analyses (e.g. size distributions of solid streams, chemical composition of chemical streams). In this paper various formulae are developed which can be used to estimate stream flow rates or weight ratios given information on the stream components. The type and level of experimental error present in the stream component analyses does have an important bearing on the numerical values (and reliability) of the weight ratios calculated by the various formulae. A simple but theoretically sound method is shown for selecting appropriate estimation formulae for any given engineering operation. The derived formulae are applied to sets of experimental classification data for illustration purposes.

Jan 1, 1979

By N. Hoffman

Accurate, repeatable density measurements of a coal-magnetite-water slurry are difficult to achieve using a nuclear density gauge. Changes in the coal-to-magnetite solids ratio cause fluctuations in the readings of nuclear gauges. To investigate this problem the Electric Power Research Institute's Coal Cleaning Test Facility compared the performance of a nuclear density gauge on a coal-magnetite-water slurry with the performance of a differential pressure gauge modified with a new pressure sensor. A second aim of these preliminary tests was to determine if the differential pressure gauge is also sensitive to the type of solids in the slurry. This paper explains current slurry density measurement practices, describes the nuclear and differential pressure gauges used in the CCTF tests, and presents test methods and results.

Jan 1, 1986

By Klaus Beckmann

Gentlemen : My object reads "Longwall Rapid Advance of Coal Mining in the Federal Republic of Germany". It is true that the percentage of coal obtained in your country from longwall faces, with at present 1.2, is still rather low, but it increased considerably since 1966 with 0.4 %. The coal mines of the Federal Republic of Germany ever used longwall as the classical method of coal getting. All attempts to introduce bord and pillar mining did not lead to any wider application of this method. The principal reasons, for this appear to have been: - the deeper depth of our workings, - the wish to keep working losses as low as possible and to utilize the deposits opened up by deep and therefore expensive shafts to the furthest possible degree, - the dense sequence of seams and the mutual influencing of the working points, - the high number of disturbances in the geologically much stressed deposits, - and the necessary considerations to the protection of the densely built-upon surface.

Jan 1, 1970

By Wayne D. Gould

Planning for a project does not start with the announcement of the approval for a project. Planning actually begins when the project is only a prospect and it involves the years of experience of many people because their expertise influences the final decisions. In partial anticipation of the Pinto Valley project, as well as a search for improvement in the Copper Cities operation, two projects were undertaken. The first project was to substitute one 26" cyclone for three 20? cyclones in the single stage grinding circuit. The second project was to replace the Hunt air flotation cells with 300 cubic foot mechanical cells. The 300 cubic foot cells were just being introduced, consequently two types of cells were selected for testing. The results from both projects influenced the decisions on equipment for the Pinto Valley project.

Jan 1, 1975

By Alan R. Johnson

Because of the competitive nature of the iron ore pelletizing industry, commodities required for the production of pellets are continually being scrutinized to minimize their usage and offset rapidly escalating costs. In the Tilden pellet plant, the usage of one commodity, bentonite, has been reduced from over twenty-four pounds per long ton of pellets to as low as eight pounds per long ton. The evolution of bentonite usage from plant start-up to the present time is described.

Jan 1, 1984

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971

By Christopher Haycocks

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine de- sign, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environ- mental considerations and the visible limitations of other energy sources. The computer program discussed in this paper, RAMPLAN (Rock Mechanics Applied to Nine Planning), was constructed as part of a continuing effort at Virginia Polytechnic Institute & State University under the sponsorship of the Office of Coal Research to develop a suite of programs to benefit the mining engineer in improving mine design and evaluation techniques. This program averages out structural data values obtained from randomly placed or gridded point sources across a mining property and uses these values in structural design equations. The basic purpose of the program is to provide accurate estimates of mineable tonnages, based on a realistic assessment of structural conditions existing in the deposit, for use in subsequent evaluation programs. Program output, however, also provides sound engineering data for the mine planner to use in planning and laying out new properties. Mining dimensions produced by the program provide a good starting point for initial layouts; and as more refined procedures are developed for increasing and improving the quality and quantity of information from boreholes, this information may be used with increasing confidence. The rock mechanics principles utilized in the program are generally well-established with full details provided to the user. To produce meaningful results extensive input data, obtained from exploration borehole core data, outcrop sampling points, or mine samples, are required. To assist the engineer, details of the types of tests that should be conducted have been listed. By including all of the ground control equations in the program the otherwise long and tedious calculations can be performed easily and quickly, and the work can provide the basis for a more detailed ground control study. The program is written in Fortran IV Level G to run on an IBM 3701155 ASP and requires 156K storage.

Jan 1, 1973

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988

By N. C. Saxena, S. K. Puri, A. K. Pal

The condition-based monitoring system is an important innovation for reducing the downtime of costly, heavy earth- moving machinery (HEMM). Vibration severity measurements were made on the HEMM located at the Gevra Project, the largest coal opencast project in India. Whenever the vibration severity levels exceeded the permissible limits, necessary actions were taken to replace the defective parts of the ma- chine. The systematic vibration monitoring of 120-t (132-st) dumpers, followed by corrective measures led to a substantial increase in component life (8.18% for an 445E Dressor and 28.44% for an MK-30 Unit Rig). The associated costs (including spareparts) were reduced by 21.55% and 25.74%, respectively. Because of the reduced downtime, savings for these two dumpers over the period from March 26 to June 25,1998, were of the order of Rs.26.47 (US$0.649) million.

Jan 1, 2000

By P. R. Taylor

The ability to treat refractory gold concentrates that contain appreciable amounts of sulfur and arsenic, in an economic and environmentally safe manner is important to the gold mining industry. Processing alternatives include: autoclave oxidation, bacterial oxidation and roasting. Roasting may be the cheapest of all the alternatives if inexpensive methods can be found to contain the arsenic and sulfur. The research program, being reported here, has been evaluating the ability to use hydrated lime in the roaster to capture both the arsenic and the sulfur. Lime roasting is not a new idea, it was proposed for copper ores by Bartlett in the early 1970's (Bartlett and Haung 1973) and for cobaltite concentrates by Taylor in the early 1980's (Taylor et al., 1981). In addition, ores have been roasted that contained limestone and it was shown that partial capture of the sulfur was possible. Lime -sulfur containment has been proposed for the coal fired electricity industry, as well.

Jan 1, 1992

By Raoul Fernandez, Bernard Catalano, Guillaume Roux

The Thaumasia Joint-Venture, composed of Bouygues Travaux Publics, Soletanche- Bachy and Bessac, completed the construction of the underground section of line 2 of the Nice tramway, which comprised a 3.2 km twin track tunnel and four underground stations, in a particularly complex urban and geotechnical context. The density of the surface structures, as well as the presence of many historic buildings on its route made the construction of the tunnel even more sensitive, with a settlement threshold of Half an Inch. The joint venture faced a complex subsoil, varying from one extreme to another from highly plastic clay layers to fibrous peat and to cobbles with very high permeability, with artesian ground water, and with unforeseen anthropogenic obstacles in the tunnel section Due to the diversity of the problems encountered and their variability over short distances, the construction of the underground section of the Nice tramway, in its very sensitive urban context, undeniably constituted an unprecedented challenge.

Jun 13, 2023

By F. X. Ferney

The centrifuge which will be reviewed in this dis¬cussion is the continuous solid bowl typo. As there are presently approximately 2000 of these units operating in our country, and about 200 of these in use in the coal industry, I expect that most of you are acquainted with its operating principle. How¬ever, for those who are not familiar with the machine a brief introduction is in order. The continuous solid bowl centrifuge was first successfully marketed, worldwide by the Bird machine Company in 1934. The successful development of this unit was based primarily on the invention of a drive mechanism to properly control the differential speed between the two rotating elements. This centrifuge was introduced into the coal industry immediately following the second World War. Today there are five or six additional firms' selling this machine in our country, and approximately twenty others in Europe, England and Japan.

Jan 1, 1965

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By P. L. Sibrell

Three different refractory carbonaceous gold ores from the Carlin operation in northeastern Nevada were investigated to characterize the effect of passivation treatments on the nature of the carbonaceous material. The carbonaceous material was chemically isolated from the ores and passivated residues, and examined by FTIR spectroscopy, elemental analysis, and gold adsorption capacity. The main component of the carbonaceous material in these ores was found to be a naturally occurring activated carbon-type compound. Hydro-carbons were detected on rare occasions, but no evidence was seen for humic acids. Ore samples were passivated by autoclaving, or by treatment with sodium hypochlorite or gaseous Chlorine. In some of the passivation tests, a new peak was observed in the IR spectra of the isolated carbonaceous material, that was due to carbonyl functionalities. However, all of the passivation treatments tested decreased preg robbing significantly. This suggested that the appearance of the carbonyl peak was due to the severity of the conditions during passivation, rather than the method used.

Jan 1, 1990

In subterranean mining operations, access to communication networks deep underground is critical for transporting data, voice and video, and other supporting applications that are essential for efficient and safe operations. Whether accessing sophisticated ERP or maintenance management systems, engaging in fleet management, video surveillance, or access control, or protecting miners with wireless locator systems, these networks serve as a literal lifeline between workers deep within mines and surface operations. For this, mining networks require more than permanently installed network cabling, it also requires unique deployable systems designed for quick installation, extension and even relocation as the active mine site area moves, or equipment is moved in and out.

Mar 1, 2014

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988