Search Documents

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By C. L. Emery

The geology and early history of the discovery of potash in Saskatchewan as described by Heber Cole (1) and R. V. Thompkins (2) has dealt with the distribution of the salt beds and their potash content. From the many bore holes through the Prairie Evaporites the outlines and contours of the series have been well established. The thickest section of the salt beds lies to the north of the "barren" area and forms a belt running easterly to a point west of Yorkton. The "barren" area is a region where the salt has been redissolved and the strata have slumped down, to fill the voids. This area is of interest from the standpoint of rock mechanics. The potash-rich beds extend both east and west of the region. mentioned and the top of the Prairie Evaporite is at a depth below 3200 feet from the surface near Saskatoon and dips southerly at an average rate of about five feet to ten feet per mile.

Jan 1, 1966

By W. Collingwood

As openpit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in openpit mines is often recirculatory. This recirculation traps dust and gases in deep openpit mines. This problem is particularly acute in high-latitude openpit mines, due to a phenomenon known as atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In openpit mines, this can result in unhealthy accumulations of gases and other contaminants. In this study, the natural wind flow patterns in and around openpit mines were investigated using a computational fluid dynamics (CfD) program. Two-dimensional models were created for a variety of pit geometries. The effect of depth, slope angle and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2012

By David S. Cahn

For many years the green and dry compressive strengths' of pellets have been, considered as possible criteria of pellet performance during induration. Although widely quoted throughout the industry, little attention has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of the test. The purpose-of this study was to compare the constant deformation rate test with that using a constant loading rate in addition, the dependence of these tests on such pellet properties as size, weight, and method of balling was to be investigated.

Jan 1, 1967

By A. Bascetin

Materials produced in quarries have been used for different intentions such as concrete and cement raw material, asphalt and embankment aggregates, railway ballast. Especially in cement manufacturing, the chemical composition and the uniformity of the raw materials play a strategic role in the economy and quality of the cement process. Therefore, it is necessary to achieve uniformity and desired chemical composition and maintain these at all production stages according to the type of cement produced. To achieve this goal the production planning and pit design play an essential role. This paper briefly outlines the production optimization of cement raw materials in a quarry in Istanbul western part of Turkey. For the purpose it was used the 3D ore body modeling and the geostatistical techniques. The variation of chemical components (%CaO, %Al2O3, %Fe2O3 etc.) and quality control parametres (LSF, SR, AR and etc.) obtained from the quarry were determined. Then the values of unknown chemical components and quality control parameters in the ore body were estimated using Kriging which is one of the geostatistical interpolation methods. The open pit design was also created by specifying wall slopes and taking into consideration of the grade distributions of the benches. The most important revolution in the paper is investigating the effects of the block dimensions in block modelling which is important for reserve estimation. The other important point in the study is using the different range values in variogram analysis for determination optimal reserve estimation. n this study, the effects of two parametres on reserve and waste amount estimation were determined according to CaO% distribution. The study was pointed out that the changing of the two parameters are very important for the optimal mine planning and environmental considerations.

Jan 1, 2010

By Sun K. Kim

Hydrometallurgical processes are not free of environmental regulations. A clear understanding of the regulations under which the minerals industry operates delineates processing requirements at early stages. This paper deals' with federal environmental regulations with emphasis on the hazardous waste regulations promulgated in May, 1980. The procedure of EP toxicity test and an example of the test are described. Brief account is given of the current trend and future outlook of regulations.

Jan 1, 1982

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By Onur Golbası, Berk Gokce

Investment decisions in the mining industry are complicated by sector-specific uncertainties. This study presents a multi-submodule system dynamics model to capture the dynamic complexities of decision-making across mineral property development stages. The model includes five interconnected subsystems: valuation, production, growth strategy, demand, and finance. Developed through system decomposition, expert input, and literature, the model is tested on a hypothetical copper mine with 850 ktpa capacity and 1% cu grade. Simulated over five years with quarterly steps, it estimates an enterprise value of $78.9 million and a target growth rate of 11.2%. Results highlight the significant effects of operating costs, capital policies, and inflation on free cash flow, and the critical role of mineral reserves in sustaining growth. This model supports strategic investment analysis across different minerals and development phases, offering mining investors a robust tool for optimizing decisions.

Feb 22, 2026

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By Kwame Awuah-Ofei, Sisi Que, Shaochun Yuan, Yumin Wang, Ziwei Ding

This research sought to facilitate improved stakeholder analysis in mining by providing further insights into the preferences of local community members using discrete choice theory. While recent research has demonstrated the usefulness of discrete choice theory in mining stakeholder analysis, no previous work has examined which discrete choice model (DCM) is most suitable. This paper provides a research note on a case study in a mining community that was performed to compare three DCMs. After a thorough examination of the benefits and deficiencies of all models, this study concludes that the conditional logit model stratified by questions is the most useful DCM for mining stakeholder analysis. The recommendation is based on the usefulness and accuracy (ability to match the survey data) of this model.

Jul 25, 2022

By Mark E. Emerson

1967 will be remembered as the year the world realized it was running out of silver. In May of this year a new era in tin the history of the white metal was begun as the power of the U.S. Treasury to regulate world .silver markets was staggered by one of the most intense speculative flurries in recent times. In the past few months the price of silver has risen from $1, 29 to over $1.80 per troy ounce and with it have spiraled the prices of a host of silver-bearing consumer items. Legislation has, been enacted to conserve our coinage and meager silver stocks and today large quantities of non-existent silver are trading hands at a fast pace on the commodity exchanges throughout the world. Now that the price of silver has been set loose, forces are in motion to dull the world's appetite for silver. At the same time there is strong incentive to provide greater quantities of silver to satisfy the world's hunger' for the metal.

Jan 1, 1967

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By Shenghua Yin, Xun Chen, Rongfu Yan, Zepeng Yan, Wei Chen

The application of cemented paste backfill (CPB) with alkali-activated slag and phosphogypsum (ASP) can contribute to the sustainable development of the mining industry. The effects of PG content, NaOH content, solid content, and waste rock-rod milling sand (W/R) ratio on workability, unconfined compressive strength (UCS), and setting time of ASP-CPB were investigated in this paper. The results showed that the workability of ASP-CPB decreased with PG content and NaOH content. Compared to OPC-CPB, ASP-CPB exhibited better workability and higher long-term (7 days and 28 days) strength at predetermined backfill formulations and curing times. The mid-term strength of ASP-CPB first increased and then decreased with PG content, while the short-term strength (3 days) decreased gradually due to the influence of soluble acidic impurities. Excessive NaOH will harm the strength of ASP-CPB, possibly due to the swelling effect of the reaction products (ettringite and sulfate). Strength and setting time increased and decreased with solid contents, respectively. Moreover, the compactness of the mixture has an important effect on strength and workability. The workability and strength of ASP-CPB reached the minimum and maximum values at a W/R ratio of 5:5, respectively. Pollutant index detection indicated that most of the pollutants in ASP-CPB leachate met the discharge standard, which proved that ASP-CPB is an effective method to recover PG. The results of the research will provide theoretical guidance for the efficient recovery of PG resources and support the achievement of safe, clean, and efficient mining.

Nov 17, 2023

By Jeff Reid, Mohamed Maghari, Nicholas Joens

The Burnaby Mountain Tunnel was an integral part of the Trans Mountain Expansion Project. General Contractor, Kiewit Ledcor TMEP Partnership (KLTP), contracted with McNally Construction to build an underground tunnel between the Burnaby and Westridge Marine terminals under Burnaby Mountain. The pipeline was constructed within a 2.6-kilometre tunnel, eliminating the need to run the pipeline over the mountain and minimizing community impacts. The complexities of this Project led to multiple innovations, including the design of a Tunnel Boring Machine (TBM) capable of excavating through mixed-faced conditions concurrently thus allowing the Project team to complete the tunnel with limited geotechnical information.

Jun 23, 2024

By Andrew J. Petruska, Austin F. Oltmanns

This work proposes a capacitive load cell for conical picks to enable underground continuous mining machine operators to perform their roles away from known hazardous regions near the machine. The load cell is embedded in commercially available flexible printed circuit board, integrates with the target tooling, and demonstrates in situ force sensing of vibration signatures for continuous mining cutting tools. Changes in material constitution, tool mass, and tool geometry cause modal variations in vibrational response measurable with force sensors at the cutting interface. Time-series measurements are captured during rock cutting tests using a linear cutting machine. These measurements are segmented into small windows, less than 0.25 s, and are preprocessed using the fast Fourier transform, which highlights the modal variations. The transformed measurements are then classified into different material and wear categories using support-vector machines with the radial basis function kernel. Different normalization schemes and Fourier transform methods are tested for signal preprocessing. Results show that the power spectral density measurements with normally distributed coefficients give good results for material classification, while the normalized time-domain measurements give better results for wear classification. Under laboratory conditions, this technique is shown to classify material and wear categories with F1 score above 0.85 out of 1.0 for our experiment. This technology could be used to assist operators in assessing material and wear conditions from a safer distance. It has applications in the coal mining industry as well as other applications which use conical picks such as road milling.

Mar 25, 2023

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By Diogo Peixoto Cordova, Italo Gomes Gonçalves, Andre Cezar Zingano

The top-down extraction sequence in the sublevel open stope method relies on rib pillars to support excavations, making pillar and stope stability crucial for controlling dilution. This study introduces an integrated methodology using a genetic algorithm to optimize the layout of open stopes and rib pillars while considering both economic and geomechanical performance. The methodology incorporates user-defined parameters such as the minimum size of stopes and pillars, maximum accepted dilution and acceptable percentage of pillar failure. A profit function that attributes economic value to the geometric configurations, including geomechanical performance, is employed. The geomechanical performance, assessed using numerical models in FLAC3D, includes the average percentage of pillar failure and potential dilution. The study was tested on a mining panel from an underground gold mine using a top-down mining sequence. The optimization achieved an 8 percent increase in net profit compared to the traditional engineer’s design when 70 percent hangingwall support efficiency was assumed, and a threefold reduction in pillar failure percentage. When no hangingwall support was considered, the net profit increase reached 22 percent. These results demonstrate that the proposed methodology enables integrated optimization, balancing mining costs with geomechanical performance and reducing the need for secondary support compared to traditional methods

Nov 1, 2024

By Peter W. Lipman

In the Rocky Mountain region, variations in Tertiary mineralization correlate with changes in tectonic setting and associated igneous activity that can largely be related to tectonics along the west boundary of the American plate. Successive settings include compressional tectonics and associated continental-arc igneous activity; transitional igneous types associated with intra- and back-arc extension; and basaltic or bimodal basalt-rhyolite assemblages associated with Basin and Range extension in- ward of a growing transform boundary between Pacific and American plates.

Jan 1, 2013

By Steve Karl

Introduction US steel production dropped 5% in 1985 to 79 Mt (87 million st). US operators are producing at only about 65% of capacity. More than 600 steelmaking facilities have closed in just 10 years. And McDonalds Corp. now employs more people than the entire US steel industry's 200,000. Not gloomy enough? Well, the North American iron ore industry can expect more plant closures and capacity reductions in the coming years. And don't count on the Federal government's voluntary restraint agreements with foreign steel producers to bail out the industry. In 1985, the first full year of the restraint agreements program, steel imports were more than 25% of domestic consumption, well above the 18.5% target. That's the grim truth, according to M. A. Hanna's Robert F. Anderson. Hanna's chairman was speaking to a group of iron ore, taconite, and steel industry executives at the Minnesota Section AIME meeting in Duluth in January. Despite those depressing facts, Anderson said he believes the domestic iron ore and steel industries can survive, although they will both be shadows of their former selves. But, he is giving them five years to make the necessary adjustments or both will die. Major steel producers during the last four years have added about $7 billion in losses to their books, he said. In Minnesota's Iron Range, employment in iron ore and taconite has gone from 14,000 10 years ago to less than half that today. Anderson explained that steel producers have more capacity today that more than meets their demand for iron ore. This places great pressure on iron ore producers to restructure to survive. Hanna, for example, has been forced to close or divest its iron ore interests in Missouri, Michigan, Canada, and Minnesota since 1980. The latest casualty was the company's Butler taconite project in Minnesota. "In just five years we've reduced ownership of active pellet capacity by 80%," he said. Technological ironies Improved technology is one cause of the industry's woes, Anderson said. While these improvements are welcome in terms of remaining competitive, the irony is that some of these technological improvements are coming at the expense of the iron and steel industries. There is a growing demand for lighter and less expensive substitutes for steel. Automobiles contain about 318 kg (700 lbs) less steel than they did 10 years ago. And, Anderson said Ford Motor Co. has indicated it plans to reduce steel usage an average of 50 kg (112 lbs) per car in the next few years. One leading steel analyst has predicted that steel usage in cars will fall another 40% in the coming years. Improved steelmaking technology has also decreased raw steel production. Continuous casting is more efficient than traditional forms of steelmaking, Anderson said. Continuous casting accounted for about 43% of steel production in the US last year, compared to 9% a decade earlier. And, Japan and Korea are producing more

Jan 3, 1986

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971